| Age | Commit message (Collapse) | Author |
|---|
|
The i.MX7 has two possible Flex Timers, disabled by default. Moreover, the
block is the same as LS1021a, then the drivers can be used as-is.
Signed-off-by: Thomas Perrot <thomas.perrot@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add DT for DH DRC02 unit, which is a universal controller device.
The system has two ethernet ports, two CANs, RS485 and RS232, USB,
capacitive buttons and an OLED display.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The DH electronics PDK2 can be populated with SoM with i.MX6S/DL/D/Q
variants. Split the SoC-independent parts of the SoM and PDK2 into the
imx6qdl-dhcom-*.dtsi and reduce imx6q-dhcom-pdk2.dts to example of
adding i.MX6S/DL/D/Q variants of the SoM into a PDK2 carrier board.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Following cleanups of the devicetrees done, no change in function:
- Remove parentheses from the license
- Update copyright date
- Alphabetical sorting
- Add comments
- Update pinctrl names
- Hex values in lower case
- Set 3rd values of fixed regulators gpio property to 0
- Replace interrupt type with a define
- Remove superfluous property max-speed from the fec node
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move iomux to the end, no change in function.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The function of each SoM pins is defined in the DHCOM standard [1] and
subset of them is defined as GPIOs (pins A-W). To ensure the interchange-
ability of the DHCOM SoMs, the function of the pins are fixed and cannot
be changed. On board level the DHCOM GPIOs can be used associated with
different blocks e.g. for interrupt or reset, but the function is always
GPIO. If not used, they can be freely used in the user space.
Therefore the whole configuration of SoM pins is made in the SoM DT.
Defining the DHCOM GPIO pins as a separate pinctrl nodes makes moving a
subset of them to an appropriate block pinctrl group easier on board level,
since it is not necessary to have a large pinctrl hog group containing
unrelated pinmux entries on board level. This also makes it easy to update
the SoM DT without having to update all the board DTs too. If necessary it
is also possible to change the electrical properties of the DHCOM GPIOs by
overwriting the pinctrl on board level.
[1] https://wiki.dh-electronics.com/images/2/2e/DOC_DHCOM-Standard-Specification_R01_2016-11-17.pdf
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PDK2 board is capable of running both 100M and 1G ethernet. However,
the i.MX6 has only one ethernet MAC, so it is possible to configure
either 100M or 1G Ethernet. In case of 100M option, the PHY is on the
SoM and the signals are routed to a RJ45 port. For 1G the PHY is on
the PDK2 board with another RJ45 port. 100M and 1G ethernet use
different signal pins from the i.MX6, but share the MDIO bus.
This SoM board combination is used to demonstrate how to enable 1G
ethernet configuration.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We need the driver core fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the fixes in here as well, and resolves some merge issues with
the mhi codebase.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds a devicetree for the Freecom FSG-3, a combined router
and NAS.
Cc: Rod Whitby <rod@whitby.id.au>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a device tree for the Linksys WRV54G also known as
Gemtek GTWX5715. Some enhancements have been folded in from the
OpenWrt patches.
This supports everything in the upstream kernel with placeholders
for the out-of-tree multiphy which exist in OpenWrt.
Cc: phj@phj.hu
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds device trees for the ADI Engineering Coyote and the
Intel IXDPG425 reference design. The ethernet set-up on the
IXDPG425 is a bit dubious because I think it uses a DSA
switch chip, but this is a good as it gets right now.
The Coyote boardfile claims an IDE port exist at 0xFFFE1000
but the implementation does not use this. If you have the
board and can/want to test, please contact me.
Cc: Deepak Saxena <dsaxena@plexity.net>
Cc: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Cc: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The IXDP425, IXCDP1100, KIXRP435 and IXDP465 are similar Intel reference
designs for IXP42x, IXP43x and IXP4[56]x.
This adds device trees for these so the board files can be migrated.
Cc: Deepak Saxena <dsaxena@plexity.net>
Cc: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds support for the compact flash card slot on the
Gateworks GW2358 router.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a device tree file for the Gateworks Avila GW2348 platform
supporting all the features of the in-kernel boardfiles.
There are more boards in the Avila family, but this is the one that
is supported out-of-the-box by the current boardfiles. Some extra
features have been folded in from the upstream OpenWrt sources,
such as proper ethernet setup for both ethernet ports.
More variants can be added based on this device tree. Some of those
have DSA switches, multiple LEDs, multiple serial ports and similar
and would need some more elaborate work.
Cc: Michael-Luke Jones <mlj28@cam.ac.uk>
Cc: Deepak Saxena <dsaxena@plexity.net>
Cc: Tom Billman <kernel@giantshoulderinc.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a device tree for the Arcom Vulcan IXP42x board.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a devicetree for the Netgear WG302v2 router.
The DTS is mostly based on the upstream boardfile but I also
added in the ethernet from OpenWrt to get a more complete
system.
Cc: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replace the "simple-bus" simplification by the proper bus for
IXP4xx memory or device expansion.
Use chip-select addressing with two address cells on all the
flashes mounted on the IXP4xx devices. This includes all flash
chips.
Change the unit-name from @50000000 to @c4000000 as the DTS
validation screams. The registers for controlling the bus are
at c4000000 but the actual memory windows and ranges are at
50000000. Well it is just syntax, we can live with it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The IXP4xx has two UARTs and some platforms make use of the
second one so add this to the include DTSI.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a devicetree for the D-Link DSM-G600 Wireless Network
Storage Enclosure so that we can delete the boardfile. The boardfile
does not even define an ethernet interface as it has an external
ethernet on PCI. This devicetree is for revision A using IXP420
the rev B version uses PowerPC.
Cc: Michael-Luke Jones <mlj28@cam.ac.uk>
Cc: Rod Whitby <rod@whitby.id.au>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Michael Westerhof <mwester@dls.net>
Cc: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This moves the EPBX100 flash under the external bus on CS0
like on the other IXP4xx systems.
Cc: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This creates a more or less fully featured device tree for the
IXP42x-based Iomega NAS 100D.
We can't read out the raw flash contents for ethernet MAC, and
we cannot handle a power-off-button inside the kernel like the
boardfile does. These two things are normally done in userspace.
This conversion is part of moving all of the IXP4xx board files
over to device tree to modernize the IXP4xx kernel.
Cc: Rod Whitby <rod@whitby.id.au>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PCI hosts had bad IRQ semantics, these are all active low.
Use the proper define and fix all in-tree users.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The board features a 128MiB NAND chip and recently linux gained support
for the NAND controller on the Zynq SoC. Thus add the corresponding
devicetree nodes.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210616155437.27378-4-michael@walle.cc
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Recently, a driver for the ARM Primecell PL35x static memory controller
(including NAND controller) was added in linux. Add the corresponding
device tree node.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210616155437.27378-3-michael@walle.cc
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
After years, linux finally got a driver for the PL35x NAND controller
found on the Xilinx Zynq-7000 SoC for example. Enable support for this
driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210616155437.27378-2-michael@walle.cc
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Remove clk_ignore_unused from bootargs as it's no more needed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Remove clk_ignore_unused from bootargs as it's no more needed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Remove clk_ignore_unused from bootargs as it's no more needed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Remove clk_ignore_unused from bootargs as it's no more needed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
4KOpen (B2264) is a board based on the STMicroelectronics STiH418 soc:
- 2GB DDR
- HDMI
- Ethernet 1000-BaseT
- PCIe (mini PCIe connector)
- MicroSD slot
- USB2 and USB3 connectors
- Sata
- 40 pins GPIO header
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The STiH418 embedded the same sensor as the STiH410.
This commit adds the corresponding node, relying on the st_thermal
driver.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The rng11 is not available on the STiH418 hence is disabled in the
stih418.dtsi
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The STiH407 family (and further versions STiH410/STiH418) embedded
a serial flash controller allowing fast access to SPI-NOR.
This commit adds the corresponding node, relying on the st-spi-fsm
drivers.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The clkgen-fsyn driver now embed the clock names (assuming the
right compatible is used). Remove all clock-output-names property
and update when necessary the compatible.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The clkgen-fsyn driver now embed the clock names (assuming the
right compatible is used). Remove all clock-output-names property
and update when necessary the compatible.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The clkgen-fsyn driver now embed the clock names (assuming the
right compatible is used). Remove all clock-output-names property
and update when necessary the compatible.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The clkgen-pll driver now embed the clock names (assuming the
right compatible is used). Remove all clock-output-names property
and update when necessary the compatible.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The clkgen-pll driver now embed the clock names (assuming the
right compatible is used). Remove all clock-output-names property
and update when necessary the compatible.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The clkgen-pll driver now embed the clock names (assuming the
right compatible is used). Remove all clock-output-names property
and update when necessary the compatible.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
With the introduction of new flexgen compatible within the clk-flexgen
driver, remove the clock-output-names entry from the flexgen nodes
and set the new proper compatible corresponding.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
With the introduction of new flexgen compatible within the clk-flexgen
driver, remove the clock-output-names entry from the flexgen nodes
and set the new proper compatible corresponding.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
With the introduction of new flexgen compatible within the clk-flexgen
driver, remove the clock-output-names entry from the flexgen nodes
and set the new proper compatible corresponding.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The OMAP_PACKAGE_* Kconfig entries are no longer referenced
in the kernel so can be dropped as they're obsolete.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The MACH_OMAP3_PANDORA is no longer referenced anywhere in the kernel
options so it can now be dropped as the board has long moved to DT.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The dual_mac mode has been preserved the same way between legacy and new
driver, and one port devices works the same as 1 dual_mac port - it's safe
to switch drivers.
So, Switch BeagleBone boards to use new cpsw switch driver. Those boards
have or 2 Ext. port wired and configured in dual_mac mode by default, or
only 1 Ext. port.
For am335x-sancloud-bbe-common.dtsi also removed duplicated davinci_mdio DT
nodes which already defined in am335x-bone-common.dtsi.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Update ethernet aliases to point at CPSW switchdev driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The dual_mac mode has been preserved the same way between legacy and new
driver, and one port devices works the same as 1 dual_mac port - it's safe
to switch drivers.
So, switch Toby Churchill SL50 Series to use new cpsw switch driver.
Those boards have or 2 Ext. port wired and configured in dual_mac mode by
default, or only 1 Ext. port.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The dual_mac mode has been preserved the same way between legacy and new
driver, and one port devices works the same as 1 dual_mac port - it's safe
to switch drivers.
So, switch Bosch SHC to use new cpsw switch driver.
Those boards have or 2 Ext. port wired and configured in dual_mac mode by
default, or only 1 Ext. port.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
