| Age | Commit message (Collapse) | Author |
|---|
|
This patch supplies the Mailbox Controller nodes. In order to
request channels, these nodes will be referenced by Mailbox
Client nodes.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
This is used for CPU Frequency Scaling.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
Used for Voltage Scaling using CPUFreq.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
You'll notice that the voltage cell is populated with 0's. Voltage
information is very platform specific, even depends on 'cut' and
'substrate' versions. Thus it is left blank for a generic (safe)
implementation. If other nodes/properties are provided by the
bootloader, the ST CPUFreq driver will over-ride these generic
values.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
When compiled with "W=1", dtc complains: e.g.
"Warning (unit_address_vs_reg):
Node /soc/ipu@02800000/port@2/endpoint@0
has a unit name, but no reg property"
Endpoint nodes don't have a reg property, and the addresses
in their node names are ordinals without any special meaning
so remove them and swap them for semantic node names.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Table 8 from MX6DL datasheet (IMX6SDLCEC Rev. 5, 06/2015):
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SDLCEC.pdf
states the following:
"LDO Output Set Point (VDD_ARM_CAP) = 1.125 V minimum for operation
up to 396 MHz."
So fix the entry by adding the 25mV margin value as done in the other
entries of the table, which results in 1.15V for 396MHz operation.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
198MHz is a valid operating point for mx6sx.
Add entries for VDD_ARM_CAP and VDD_SOC_CAP voltages for 198MHz according
to the imx6sx datahseet:
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SXIEC.pdf
(a 25mV offset is added to the minimum allowed values for safety).
These values also match the ones from the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Adjust the VDD_ARM_CAP and VDD_SOC_CAP voltages according to
Table-11 from MX6UL datasheet:
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6ULCEC.pdf
(a 25mV offset is added to the minimum allowed values for safety).
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
into next/dt
Merge "ARM: dts: Add OXNAS Platform Bindings" from Neil Armstrong:
* tag 'ox810se-arm-dt-v4.6-rc3' of https://github.com/superna9999/linux:
ARM: boot: dts: Add Western Digital My Book World Edition device tree
dt-bindings: Add Western Digital to vendor prefixes
dt-bindings: Add OXNAS bindings
ARM: boot: dts: Add Oxford Semiconductor OX810SE dtsi
dt-bindings: Add Oxford Semiconductor to vendor prefixes
dt-bindings: irq: arm,versatile-fpga: add compatible string for OX810SE SoC
|
|
into next/soc
Merge "ARM: Add OXNAS Platform Support" from Neil Armstrong
This is for the ARM926 based ox810 chip used in some older
NAS appliances. There is another related ox820 chip based on
ARM11 that might get added here later.
* tag 'ox810se-arm-v4.6-rc3' of https://github.com/superna9999/linux:
MAINTAINERS: add maintainer entry for ARM/OXNAS platform
ARM: Add new mach-oxnas
irqchip: versatile-fpga: add new compatible for OX810SE SoC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Merge "Renesas ARM Based SoC Pci Defconfig Updates for v4.7" from Simon Horman:
* Remove Gen2 designation from Kconfig for R-Car PCIE driver
* tag 'renesas-pci-defconfig-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
PCI: rcar-pcie: Remove Gen2 designation from Kconfig
|
|
DEBUG_HI3716_UART was supposed to be renamed to DEBUG_HIX5HD2_UART, but
accidentally both got left in place, which results in a build error when
CONFIG_DEBUG_UART_PHYS is not set as it should be.
This removes the old symbol.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 12aae3097454 ("ARM: debug: Rename Hi3716 to HIX5HD2")
Acked-by: Wei Xu <xuwei5@hisilicon.com>
|
|
This patch adds a new config for MPS2 platform.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Application Notes 399 and 400 shares the same memory map and
features. Both are shipped with Cortex-M7 and have the same peripheral
as AN385/AN386, but with different location of PSRAM and Ethernet
controller.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Application Notes 385 and 386 shares the same memory map and features
except the CPU is used. AN385 is supplied with Cortex-M3 CPU and AN386
is supplied with Cortex-M4.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The Cortex-M Prototyping System (or V2M-MPS2) is designed for
prototyping and evaluation Cortex-M family of processors including the
latest Cortex-M7
It comes with a range of useful peripherals including 8MB single cycle
SRAM, 16MB PSRAM, Ethernet, QSVGA touch screen panel, 4bit RGB VGA
connector, Audio, SPI and GPIO.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC Fixes for v4.6
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
This is a backmerge of v4.6 fixes, to avoid a merge conflict between 4.6
and our next/dt branch.
* tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
|
|
Fix a typo on PIN_PD24 for UTXD2 and FLEXCOM4_IO3 which were
wrongly linked to PIN_PD23).
Signed-off-by: Florian Vallee <fvallee@eukrea.fr>
Fixes: 7f16cb676c00 ("ARM: at91/dt: add sama5d2 pinmux")
Cc: stable@vger.kernel.org # v4.4+
[nicolas.ferre@atmel.com: add commit message, changed subject]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Merge "Second Round of Renesas ARM Based SoC R-Car SYSC Updates for v4.7" from Simon Horman:
Introduce a DT-based driver for the R-Car System Controller, as found on
Renesas R-Car H1, R-Car Gen2, and R-Car Gen3 SoCs.
* tag 'renesas-rcar-sysc2-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (30 commits)
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
soc: renesas: rcar-sysc: Add support for R-Car H1 power areas
soc: renesas: rcar-sysc: Enable Clock Domain for I/O devices
soc: renesas: rcar-sysc: Make rcar_sysc_power_is_off() static
soc: renesas: rcar-sysc: Add DT support for SYSC PM domains
soc: renesas: rcar-sysc: Improve rcar_sysc_power() debug info
soc: renesas: Move pm-rcar to drivers/soc/renesas/rcar-sysc
clk: renesas: cpg-mssr: Export cpg_mssr_{at,de}tach_dev()
clk: renesas: mstp: Provide dummy attach/detach_dev callbacks
clk: renesas: Provide Kconfig symbols for CPG/MSSR and CPG/MSTP support
soc: renesas: Add r8a7795 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7794 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7793 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7791 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7790 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7779 SYSC PM Domain Binding Definitions
...
|
|
Add Western Digital My Book World Edition device tree based on
Oxford Semiconductor OX810SE SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add mach-oxnas directory containing Kconfig.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
The BA16 module has a PMIC that uses the WDOG_B output from iMX6 to
reset the system on a watchdog timeout. Configure the watchdog to assert
the external reset signal (WDOG_B) using fsl,ext-reset-output property.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Previously the LDB_DIx clocks could be specified in the ldb node. With
the ERR009219 errata fix applied, the ldb_di clocks now needs to be
specified in the clks node to ensure the clocks are setup early in the
boot process.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The default monitor that ships with B850v3 requires a 65MHz pixel clock.
65MHz can not be achieved using PLL3 (480MHz/7=68.5MHz). Hence set the
LDB_DIx clock source to PLL5. Since PLL5 is already in use by IPU1_DIx,
set the clock source for IPU1_DIx to PLL2_PFD2 to allow simultaneous
display on both LVDS and HDMI interface.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove ldb panel entry for the following reasons:
- The b850v3 has an onboard LVDS to DisplayPort converter (STDP4028). So
we should not limit the monitors that can be connected by hardcoding the
auo,b133htn01 1080p panel.
- The default resolution on the LVDS interface needs to be WXGA or less.
Otherwise when a 1080p monitor is connected to the HDMI port there is no
output on both the LVDS and HDMI ports since a single IPU on i.MX6 can
not handle two 1080p displays. With the panel entry removed from the
devicetree, drm driver defaults the resolution on LVDS interface to XGA.
Once in userspace, applications can set the desired resolution on LVDS
interface over IPU2 CRTC.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
http://git.linaro.org/people/daniel.lezcano/linux into tmp
Pull ARM cpuidle changes for v4.7 from Daniel Lezcano.
* 'cpuidle/4.7' of http://git.linaro.org/people/daniel.lezcano/linux:
drivers: firmware: psci: use const and __initconst for psci_cpuidle_ops
soc: qcom: spm: Use const and __initconst for qcom_cpuidle_ops
ARM: cpuidle: constify return value of arm_cpuidle_get_ops()
ARM: cpuidle: add const qualifier to cpuidle_ops member in structures
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Enable dm814x and dra62x clock driver. This branch has a dependency
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
* tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add clocks for dm814x ADPLL
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Put nodes after of_address_to_resource() in case the nodes might be
released while parsing in them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC Updates for v4.7" from Simon Horman:
Drop support for Cortex A8 in timer code
* tag 'renesas-soc-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: timer: Drop support for Cortex A8
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
Merge "DaVinci SoC updates for v4.7" from Sekhar Nori:
These are preparatory patches to support a USB PHY driver for USB on DA850
SoC. This should eventually lead to USB working again on this device.
* tag 'davinci-for-v4.7/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: clk: add set_parent callback for mux clocks
ARM: davinci: da8xx: move usb code to new file
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/cleanup
Merge "DaVinci cleanups for v4.7" from Sekhar Nori:
It includes removal of some unused macros and data- -structures and use
of helper macros to reduce code.
* tag 'davinci-for-v4.7/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
|
|
into next/drivers
Merge "Broadcom ARM-based SoCs drivers changes" from Florian Fainelli:
- Justin adds a soc_dev driver to properly report to user-space the Broadcom
STB SoC family, product and revision
- Florian reworks how the brcmstb_gisb driver dependency is done to enable it
on Broadcom STB MIPS-based SoCs and remove a select in
arch/arm/mach-bcm/Kconfig
* tag 'arm-soc/for-4.7/drivers' of http://github.com/Broadcom/stblinux:
bus: brcmstb_gisb: Rework dependencies
soc: brcmstb: add SoC driver to brcmstb
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "soc/tegra: Changes for v4.7-rc1" from Thierry Reding:
This contains a bunch of preparatory patches to the PMC driver which are
a prerequisite to moving the driver to generic power domains.
* tag 'tegra-for-4.7-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: Update NVIDIA PMC for Tegra
soc/tegra: pmc: Wait for powergate state to change
soc/tegra: pmc: Ensure GPU partition can be toggled on/off by PMC
soc/tegra: pmc: Remove additional check for a valid partition
soc/tegra: pmc: Fix verification of valid partitions
soc/tegra: pmc: Fix testing of powergate state
soc/tegra: pmc: Change powergate and rail IDs to be an unsigned type
soc/tegra: pmc: Protect public functions from potential race conditions
soc/tegra: pmc: Restore base address on probe failure
soc/tegra: pmc: Remove non-existing L2 partition for Tegra124
soc/tegra: pmc: Remove non-existing power partitions for Tegra210
soc/tegra: pmc: Remove debugfs entry on probe failure
soc/tegra: pmc: Fix sparse warning for tegra_pmc_init_tsense_reset()
soc/tegra: pmc: Add missing structure members to kernel-doc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/drivers
Merge "move Versatile flash protection to the device tree" from Linus Walleij:
This is a set of patches removing the board file code
for Versatile flash handling and instead moving it over
to the device tree and a special add-on file.
* tag 'versatile-flash-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: move flash registration to device tree
ARM: versatile: move flash registration to the device tree
mtd: augment the "arm,versatile-flash" bindings
mtd: physmap_of: add a hook for Versatile write protection
Acked-by: Brian Norris <computersforpeace@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Merge "ARM: Keystone DTS for 4.7" from Santosh Shilimkar:
- Remainder k2-* rename to keystone-*
- PSCI node info
- SPI alias nodes for bootloaders
* tag 'keystone_dts_for_4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: dts: add psci command definition
ARM: dts: keystone: Add aliases for SPI nodes
ARM: dts: k2*: Rename the k2* files to keystone-k2* files
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
Merge "ARMv7 Vexpress updates/fixes for v4.7" from Sudeep Holla:
1. Support for external expansion bus useful for additional hardware
e.g. LogicTile Express daughterboards (Brian Starkey)
2. Fix for device node name unit-address presence/absence warnings
enabled in recently update DTC (Sudeep Holla)
* tag 'vexpress-for-v4.7/updates' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: Add external expansion bus to DT
ARM: dts: vexpress: fix node name unit-address presence warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.7" from Simon Horman:
* Configure NMI key as wakeup source in DT of kzm9g board
* Add SDHI support to DT of gose board
* Add support of UHS-I SDR-50 for SDHI to DT of r8a7790 SoC
* Correct interrupt type for ARM TWD in DT of r8a7779 and sh73a0 SoCs
* Add IIC support to DT of r8a7794 SoC
* Add CAN support to DT of r8a7793 and r8a7794 SoCs
* Add SCIF2 support to r8a7790 device tree
* Use CAN, JPU and USB3.0 fallback compatibility string
in DT of r8a7791 and r8a7790 SoCs
* tag 'renesas-dt-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits)
ARM: dts: gose: Enable SDHI controllers
ARM: dts: r8a7793: Add SDHI controllers
ARM: dts: r8a7790: fix max-frequency for SDHI
ARM: dts: kzm9g: Configure NMI key as wake-up source
ARM: dts: r8a7790: lager: Enable UHS-I SDR-50
ARM: dts: r8a7790: Set maximum frequencies for SDHI clocks
ARM: dts: r8a7791: Use USB3.0 fallback compatibility string
ARM: dts: r8a7790: Use USB3.0 fallback compatibility string
ARM: dts: r8a7779: Correct interrupt type for ARM TWD
ARM: dts: sh73a0: Correct interrupt type for ARM TWD
ARM: dts: r8a7794: Add IIC nodes
ARM: dts: r8a7794: add IIC clocks
ARM: dts: r8a7793: add CAN nodes to device tree
ARM: dts: r8a7793: add CAN clocks to device tree
ARM: dts: r8a7794: add CAN nodes to device tree
ARM: dts: r8a7794: add CAN clocks to device tree
ARM: dts: r8a7790: use fallback can compatibility string
ARM: dts: r8a7791: use fallback can compatibility string
ARM: dts: r8a7790: Add SCIF2 device node
ARM: dts: r8a7790: Add SCIF2 clock
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/defconfig
Merge "ARM: Keystone HOTPLUG and PSCI config update for 4.7" from Santosh Shilimkar
* tag 'keystone_config_for_4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: configs: keystone: Add CPU Hotplug related options
|
|
into next/defconfig
Merge "This pull request contains defconfig changes for Broadcom ARM-based SoCs"
from Florian Fainelli:
- Eric enables more BCM2835 peripherals in multi_v7_defconfig: watchdog, I2S,
switches from the sdhci-bcm2835 to the sdhci-iproc driver, DWC2 USB controller
- Eric also enables more BCM2835 peripherals in bcm2835_defconfig: VC4, NFS root
Power Management support, switching sdhci-bcm2835 for sdhci-iproc
* tag 'arm-soc/for-4.7/defconfig' of http://github.com/Broadcom/stblinux:
ARM: bcm2835: Enable NFS root support.
ARM: bcm2835: Enable the VC4 graphics driver in the defconfig
ARM: bcm2835: Enable CONFIG_PM.
ARM: bcm2835: Switch BCM2835 to sdhci-iproc.c for MMC
ARM: multi_v7_defconfig: Build in DWC2 USB support
ARM: multi_v7_defconfig: Switch BCM2835 to sdhci-iproc.c for MMC
ARM: multi_v7_defconfig: Add more BCM2835 support
|
|
into next/defconfig
Merge "mvebu defconfig for 4.7 (part 1)" from Gregory CLEMENT
- Use the new cryto engine(mv_cesa) in the mvebu and multi-arm
defcongig files
- Attach mvebu_*_defconfig to the mvebu maintainers
* tag 'mvebu-defconfig-4.7-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu_v5_defconfig: Switching to the new Marvell's cryptographic engine driver
ARM: multi_v7_defconfig: Enabling the new Marvell's cryptographic engine driver
MAINTAINERS: attach arch/arm/configs/mvebu_*_defconfig to relevant maintainers
ARM: mvebu_v7_defconfig: Enabling the new Marvell's cryptographic engine driver
|
|
This NAND controller device is used on UniPhier SoCs (and I know
it is also used on SoC FPGA).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/defconfig
Merge "Defconfig (exynos and multi_v7) changes for Exynos based boards for v4.7" from Krzysztof Kozłowski:
1. Enable additional drivers for Trats2 board (Exynos4412).
2. Enable CPUFreq governors as modules.
* tag 'samsung-defconfig-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: multi_v7_defconfig: Enable CPUFreq governors as modules
ARM: exynos_defconfig: Enable CPUFreq governors as modules
ARM: exynos_defconfig: Enable Trats2 audio codec, touchscreen and sensors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Enable dm814x and dra62x clock driver. This branch has a dependency
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
* tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add clocks for dm814x ADPLL
|
|
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch add rockchip's compatible string to the compat list and
remove similar code from platform code for supporting generic platdev
driver.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
