| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.6/fixes
ARM: OMAP2+: clockdomain: another fix for v4.6-rc
For DRA7xx platforms, add a workaround for missed timer interrupts
that appears to be due to an integration bug (erratum i874)
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-fixes-b-for-v4.6-rc/20160413020850/
(The DRA7xx board here has not yet been added into the testbed.)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Renesas ARM Based SoC Defconfig Updates for v4.7
* Enable I2C demultiplexer and slave eeprom in
shmobile and multi_v7defconfigs
* tag 'renesas-defconfig-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: defconfig: enable I2C demultiplexer and slave eeprom
ARM: multi_v7_defconfig: enable I2C demultiplexer and slave eeprom
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC Cleanup for v4.7
* Remove unnecessary clock-output-names properties from DT
* Use generic pinctrl properties in DT
* tag 'renesas-cleanup-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (26 commits)
ARM: dts: sh73a0: Remove unnecessary clock-output-names properties
ARM: dts: r8a73a4: Remove unnecessary clock-output-names properties
ARM: dts: lager: Remove unnecessary clock-output-names properties
ARM: dts: porter: Remove unnecessary clock-output-names properties
ARM: dts: koelsch: Remove unnecessary clock-output-names properties
ARM: dts: gose: Remove unnecessary clock-output-names properties
ARM: dts: r8a7794: Remove unnecessary clock-output-names properties
ARM: dts: r8a7793: Remove unnecessary clock-output-names properties
ARM: dts: r8a7791: Remove unnecessary clock-output-names properties
ARM: dts: r8a7779: Remove unnecessary clock-output-names properties
ARM: dts: r8a7778: Remove unnecessary clock-output-names properties
ARM: dts: r8a7740: Remove unnecessary clock-output-names properties
ARM: dts: r7s72100: Remove unnecessary clock-output-names properties
ARM: dts: r8a7790: Remove unnecessary clock-output-names properties
ARM: dts: kzm9d: use generic pinctrl properties
ARM: dts: kzm9g: use generic pinctrl properties
ARM: dts: silk: use generic pinctrl properties
ARM: dts: alt: use generic pinctrl properties
ARM: dts: gose: use generic pinctrl properties
ARM: dts: porter: use generic pinctrl properties
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
clkout1 clock node and its generation tree was missing. Add this based
on the data on TRM and PRCM functional spec.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
First DT batch for 4.7, additions for sama5d2 SoC:
- chipid node to identify the SoC
- SFR node (Special Function Registers)
- LCD controller's node
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d2: add LCD controller
ARM: dts: at91: sama5d2: add chipid node
ARM: dts: at91: sama5d2: add SFR node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/soc
First SoC batch for 4.7:
- chipid registers reading for SoC detection
* tag 'at91-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/soc: reference the whole sama5d2 family
ARM: at91: use chipid device for soc detection
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This allows reporting & debugging problems occurring early in the boot
process.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
There are few devices that have USB power controlled using GPIO. Linux
USB host driver (bcma-hcd) already supports this by reading vcc-gpio
from DT. Set it properly for all known devices.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A batch of fixes for -rc4, for various platforms.
Nothing really substantial and worth pointing out in particular; small
fixes for various bugs, see shortlog for details"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: sa1100: remove references to the defunct handhelds.org
bus: uniphier-system-bus: fix condition of overlap check
ARM: uniphier: drop weird sizeof()
ARM: dts: am335x-baltos-ir5221: fix cpsw_emac0 link type
ARM: OMAP: Correct interrupt type for ARM TWD
ARM: DRA722: Add ID detect for Silicon Rev 2.0
ARM: dts: am43xx: fix edma memcpy channel allocation
ARM: dts: AM43x-epos: Fix clk parent for synctimer
ARM: OMAP2: Fix up interconnect barrier initialization for DRA7
documentation: Fix pinctrl documentation for Meson8 / Meson8b
ARM: dts: amlogic: Split pinctrl device for Meson8 / Meson8b
ARM: mvebu: Correct unit address for linksys
bus: mvebu-mbus: use %pa to print phys_addr_t
arm64: dts: vulcan: Update PCI ranges
ARM: u8500_defconfig: turn on the Synaptics RMI4 driver
ARM: pxa: fix the number of DMA requestor lines
ARM: OMAP2+: hwmod: Fix updating of sysconfig register
ARM: OMAP2+: Use srst_udelay for USB on dm814x
|
|
Add the config options needed to get CPU hotplug functional.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
This commit adds definition for cpu_on, cpu_off and cpu_suspend commands.
These definitions must match the corresponding PSCI definitions in
boot monitor.
Having those command and corresponding PSCI support in boot monitor allows
run time CPU hot plugin.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Add aliases for SPI nodes, this is required to probe the SPI devices in
U-Boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Pull KVM fixes from Radim Krčmář:
"ARM fixes:
- Wrong indentation in the PMU code from the merge window
- A long-time bug occuring with running ntpd on the host, candidate
for stable
- Properly handle (and warn about) the unsupported configuration of
running on systems with less than 40 bits of PA space
- More fixes to the PM and hotplug notifier stuff from the merge
window
x86:
- leak of guest xcr0 (typically shows up as SIGILL)
- new maintainer (who is sending the pull request too)
- fix for merge window regression
- fix for guest CPUID"
Paolo Bonzini points out:
"For the record, this tag is signed by me because I prepared the pull
request. Further pull requests for 4.6 will be signed and sent out by
Radim directly"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: mask CPUID(0xD,0x1).EAX against host value
kvm: x86: do not leak guest xcr0 into host interrupt handlers
KVM: MMU: fix permission_fault()
KVM: new maintainer on the block
arm64: KVM: unregister notifiers in hyp mode teardown path
arm64: KVM: Warn when PARange is less than 40 bits
KVM: arm/arm64: Handle forward time correction gracefully
arm64: KVM: Add braces to multi-line if statement in virtual PMU code
|
|
As reported in [1], rename the k2* dts files to keystone-* files
this will force consistency throughout.
Script for the same (and hand modified for Makefile and MAINTAINERS
files):
for i in arch/arm/boot/dts/k2*
do
b=`basename $i`;
git mv $i arch/arm/boot/dts/keystone-$b;
sed -i -e "s/$b/keystone-$b/g" arch/arm/boot/dts/*[si]
done
NOTE: bootloaders that depend on older dtb names will need to be
updated as well.
[1] http://marc.info/?l=linux-arm-kernel&m=145637407804754&w=2
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
The DCU IP has distinct clock inputs for register access and the
pixel clocks, at least in some implementations. LS1021a seems to
use the same clock, therefore specify the same clock for "dcu"
and "pix".
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Both DSPI have signals SPIn_PCS[0:5] so in summary 6 chip-selects, not 5.
Fix that.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add gpio nodes for ls1021a platform dts file. The gpio
IP block of the ls1021a can be supported by the code
drivers/gpio/gpio-mpc8xxx.c.
The compatible "fsl,qoriq-gpio" is used by gpio driver:
drivers/gpio/gpio-mpc8xxx.c to implement general gpio
functionalities.
The chip-specific compatible "fsl,ls1021a-gpio" may be
used to fix potential gpio IP block errata or other
chip-specific gpio issues.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The vqmmc supply is not connected to bio supply on the BA16 module.
Hence remove vqmmc-supply property in usdhc3 node.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add SCFG MSI dts node and add msi-parent property to PCIe dts node
that points to the corresponding MSI node.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to Documentation/devicetree/bindings/net/fsl-fec.txt the polarity
of "phy-reset-gpios" is assumed to be active-low unless a separate property
"phy-reset-active-high" is available. So replace the inconsistent polarity
description to make the correct active-low reset behavior more obvious.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This commit adds support for Rev. B of a Zodiac Inflight Innovations
development board, mainly intended for DSA and ARINC 429 development
work.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing reg properties to AIPS bus and Cortex-A5's PMU unit.
This change avoids the following warnings:
Warning (unit_address_vs_reg): Node /soc/aips-bus@40000000 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@40080000 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@40080000/pmu@40089000
has a unit name, but no reg property
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The NAND flash memory populated on Colibri VF61 allows faster NAND
timings than the flash memory on VF50. Additionally, due to divider
limitations, VF61 did clock the flash even slower than VF50. Assign
the NFC clock in the module specific device trees vf500-colibri.dtsi
and vf610-colibri.dtsi respectively.
This increases raw read speed on Colibri VF61 by about 20%.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Vybrid based Colibri modules provide a on-module PHY which is
connected to the second FEC instance FEC1. Since the on-module
Ethernet port is considered as primary ethernet interface, alias
fec1 as ethernet0. This also makes sure that the first MAC address
provided by the boot loader gets assigned to the FEC instance used
for the on-module PHY.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Introduce imx6sx-sdb-sai.dts so that it is possible to use the
SAI interface.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Property 'dma-source' is not used anywhere, nor it is documented, so
let's just get rid of it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to sdma_peripheral_type in include/linux/platform_data/dma-imx.h
IMX_DMATYPE_SAI corresponds to index 24, so fix it accordingly.
Suggested-by: Zidan Wang <zidan.wang@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
pwm2 is provided on the BA16 Q7 module, but is not used on any
of the current configurations. However, future platforms may
utilize this device, so we are simply disabling the node rather
than removing it completely.
Signed-off-by: Justin Waters <justin.waters@timeys.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Based on i.MX6 SoloX with 1GB of RAM.
https://boundarydevices.com/product/nit6_solox-imx6/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It is preferred to use the panel compatible string rather than passing the
LCD timings in the device tree.
So pass the "hannstar,hsd100pxn1" compatible string to describe
the LVDS panel on this board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This baseboard can be used with all TX6 SoMs, but only a certain set
of combinations can be ordered by default. Add support for these
combinations in mainline, so that users can easily adopt their own
combination of SoM and baseboard themselves.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the following i.MX6 based modules from Ka-Ro
electronics GmbH:
TX6S-8034:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 256MiB DDR3 SDRAM
ROM 128MiB NAND Flash
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
TX6S-8035:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 512MiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
TX6U-8033:
Processor Freescale i.MX 6 Dual Lite, 800MHz
RAM 1GiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
TX6Q-1036:
Processor Freescale i.MX 6Quad, 1GHz
RAM 1GB DDR3 SDRAM 64-bit
ROM 8GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range Extended Consumer Grade (-20°C to 105°C Tj)
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing pinctrl for the RTS/CTS lines to uart1 and set the
fsl,uart-has-rtscts property on all UARTs to enable support for HW
handshake.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the pinctrl setting for the board LED from the hoggrp node
to a separate node referenced by the LED driver, so that the pin is
free to be used for different purpose when the LED driver is disabled.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
DT maintainers don't like the 'simple-bus' container around the
regulator nodes. So remove it.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Based on i.MX6 Quad Plus with 4GB of RAM.
https://boundarydevices.com/product/nitrogen6max/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add mdio node and an appropriate PHY configuration to enable use of
the PHY interrupt for link status changes.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the function node around the pinctrl nodes that was obsoleted
by commit 5fcdf6a7ed95 ("pinctrl: imx: Allow parsing DT without
function nodes"), we can save this container node.
Also move the iomux node to the bottom of the file to improve
readability of the file.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The spidev driver doesn't like to be instantiated via a naked 'spidev'
compatible, though it is very convenient to invoke it this way without
a dedicated SPI device for basic functional testing.
Disable the spi node by default to silence the WARN_ON() from the
spidev driver, but leave the configuration intact otherwise.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add an empty line between properties and subnode in the clocks node.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the imx6*-tx6* files to this combination.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
mode
With SION set the level on such a pin is reported to the UART. So for
example when the CS5 pin is configured for GPIO mode and the level
changes this triggers an RTS interrupt on uart5.
Adding some severity to this issue: The imx uart driver currently
doesn't handle correctly irqs for changes on RI and DCD which are
enabled automatically when the respective UART is driven in DTE mode
(that is, has the fsl,dte-mode property set in the device tree). This
results in a stuck machine because the irq isn't cleared and so stalls
the CPU.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Apart from a few additions this also contains two fixes where the daisy
chain input selection register was missing. Moreover dropped _MUX from
some pins for consistency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Utilize the new PCIe Tx configuration to properly support the correct
values.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The TXUL-0010/-0011 modules are Computers On Module manufactured by
Ka-Ro electronics GmbH with the following characteristics:
Processor Freescale i.MX 6UltraLite MCIMX6G2, 528 MHz
RAM 256MB 16-bit DDR3 SDRAM
ROM 128MB NAND Flash (TXUL-0010) / 4GB eMMC (TXUL-0011)
Power supply Single 3.3 to 5V
Size 26mm SO-DIMM
Temp. Range -40°C to 85°C
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable dcu node which is used by the DCU DRM driver. Assign the 5.7"
EDT panel with VGA resolution which Toradex sells often with the
evaluation board.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the dcu and tcon nodes to enable the Display Controller Unit
and Timing Controller in Vybrid's SoC level device-tree file.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Based on i.MX7 Dual with 1GB of RAM.
https://boundarydevices.com/product/nitrogen7/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
