| Age | Commit message (Collapse) | Author |
|---|
|
This enables userspace to signal the bootloader to go into the
bootloader or recovery mode.
The magic values can be found in both the downstream kernel and the LK
kernel (bootloader).
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Before this change, trying to boot from the internal storage would
result in a lot of errors like:
[ 11.224046] mmc0: cache flush error -110
[ 11.224180] blk_update_request: I/O error, dev mmcblk0, sector 0 op 0x1:(WRITE) flags 0x800 phys_seg 0 prio class 0
or:
[ 137.544673] mmc0: tuning execution failed: -5
[ 137.569832] mmcblk0: error -110 requesting status
[ 137.593558] mmcblk0: recovery failed!
With this patch, there are no more sdhci errors and booting works fine.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The gpio is not used for SD card detection on the FP2.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes and cleanups from Juergen Gross:
- a fix in the Xen balloon driver avoiding hitting a BUG_ON() in some
cases, plus a follow-on cleanup series for that driver
- a patch for introducing non-blocking EFI callbacks in Xen's EFI
driver, plu a cleanup patch for Xen EFI handling merging the x86 and
ARM arch specific initialization into the Xen EFI driver
- a fix of the Xen xenbus driver avoiding a self-deadlock when cleaning
up after a user process has died
- a fix for Xen on ARM after removal of ZONE_DMA
- a cleanup patch for avoiding build warnings for Xen on ARM
* tag 'for-linus-5.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: fix self-deadlock after killing user process
xen/efi: have a common runtime setup function
arm: xen: mm: use __GPF_DMA32 for arm64
xen/balloon: Clear PG_offline in balloon_retrieve()
xen/balloon: Mark pages PG_offline in balloon_append()
xen/balloon: Drop __balloon_append()
xen/balloon: Set pages PageOffline() in balloon_add_region()
ARM: xen: unexport HYPERVISOR_platform_op function
xen/efi: Set nonblocking callbacks
|
|
SPI_STM32_QSPI must be set in buildin as rootfs can be
located on QSPI memory device.
Link: https://lore.kernel.org/r/20191004124025.17394-1-patrice.chotard@st.com
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The TWL4030 used on the Logit PD Torpedo SOM does not have the
keypad pins routed. This patch disables the twl_keypad driver
to remove some splat during boot:
twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22
twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap
twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed error time stamps]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Commit 0ed266d7ae5e ("clk: ti: omap3: cleanup unnecessary clock aliases")
removed old omap3 clock framework aliases but caused omap3-rom-rng to
stop working with clock not found error.
Based on discussions on the mailing list it was requested by Tero Kristo
that it would be best to fix this issue by probing omap3-rom-rng using
device tree to provide a proper clk property. The other option would be
to add back the missing clock alias, but that does not help moving things
forward with removing old legacy platform_data.
Let's also add a proper device tree binding and keep it together with
the fix.
Cc: devicetree@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes: 0ed266d7ae5e ("clk: ti: omap3: cleanup unnecessary clock aliases")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In general we should check for GP device instead of HS device unless
the other options such as EMU are also checked. Otherwise omap3-rom-rng
won't probe on few of the old n900 macro boards still in service in
automated build and boot test systems.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Enable auto-configuration of VUART SIRQ polarity on AST2500.
Signed-off-by: Oskar Senft <osk@google.com>
Link: https://lore.kernel.org/r/20190905144130.220713-3-osk@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commits 3d109bdca981 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa28 ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca981 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa28 ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Rio500 kernel driver has not been used by Rio500 owners since 2001
not long after the rio500 project added support for a user-space USB stack
through the very first versions of usbdevfs and then libusb.
Support for the kernel driver was removed from the upstream utilities
in 2008:
https://gitlab.freedesktop.org/hadess/rio500/commit/943f624ab721eb8281c287650fcc9e2026f6f5db
Cc: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/6251c17584d220472ce882a3d9c199c401a51a71.camel@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add an rtc label so we just need to alias it from derived boards.
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Link: https://lore.kernel.org/r/20191002145914.14874-1-kamel.bouhara@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add mmc capabilities for SDMMC0 for this board.
With this enabled, eMMC connected card is detected as:
mmc0: new DDR MMC card at address 0001
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/1565252928-28994-2-git-send-email-eugen.hristev@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The general-purpose OMAP3530, OMAP3630, and DM3730 have hardware
crypto engines that appear to be functional despite limited
documentation.
This patch enables them as modules.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When running make savedefconfig ARCH=arm, CONFIG_DMA_CMA
changed location. To help facilitate future changes to
omap2plus_defconfig, this patch re-syncs the omap2plus file
with the updated location generated by make savedefconfig.
No items were removed or added during this patch.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The omap panel-dpi driver was removed in
Commit 8bf4b1621178 ("drm/omap: Remove panel-dpi driver")
The tFP410 and DVI connector was remove in
Commit be3143d8b27f ("drm/omap: Remove TFP410 and DVI connector drivers")
This patch removes these items from the omap2plus_defconfig.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The old omapdrm panels got removed for v5.4 in favor of generic panels,
and the Kconfig options changed. Let's update omap2plus_defconfig
accordingly so the same panels are still enabled.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
Here are fixes for omaps to deal with few regressions, and to fix
more boot time errors and warnings:
- The recent ti-sysc interconnect target module driver changes had
incorrect clock bits for both clocks and dts that cause warnings
- For omap3-gta04, gpio changes caused the LCD to break a while back,
and after discussing things the right fix is to set spi-cs-high
- Recent omapdrm changes to use generic panels caused tfp410 to be
disabled as we now must enable the generic support for it in
defconfig
- Recent omapdrm and backlight changes also finally made droid4 LCD
to work, so let's enable it in the defconfig it can be used out
of the box. This is not strictly a fix, but we still also have the
older CONFIG_MFD_TI_LMU options available so this cuts down the
confusion for trying to guess which display and which backlight
is needed
- Recent ti-sysc interconnect target module changes need the gpio
module disabled on some boards, but this now needs to happen at
the module level, not at the gpio driver level
- Recent changes to probe system timers with ti-sysc caused warnings
about mismatch in syconfig registers, so let's configure the option
for RESET_STATUS as available in the TRMs
- Recent changes to probe LCDC with ti-sysc caused warnings about
mismatch in sysconfig registers, so let's configure the missing
idlemodes for both platform data and dts as documented in TRMs
- Since we moved mach-omap2 to probe with device tree, we've been
getting voltage controller warnings. Turns out this code is no
longer needed, so let's just remove omap2_set_init_voltage() to
get rid of the pointless warnings
- Configure am4372 dispc memory bandwidth to avoid underflow errors
* tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: Set memory bandwidth limit for DISPC
ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
ARM: OMAP2+: Add missing LCDC midlemode for am335x
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
ARM: dts: Fix gpio0 flags for am335x-icev2
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
ARM: dts: Fix wrong clocks for dra7 mcasp
clk: ti: dra7: Fix mcasp8 clock bits
Link: https://lore.kernel.org/r/pull-1570040410-308159@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add wdog1 node to support watchdog driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Select CONFIG_IMX7ULP_WDT by default to support i.MX7ULP watchdog.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add interrupts to Dynamic Memory Controller in Exynos5422 and Odroid
XU3-family boards. It will be used instead of devfreq polling mode
governor. The interrupt is connected to performance counters private
for DMC, which might track utilisation of the memory channels.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
DMC Adaptive Voltage and Frequency Scaling driver in interrupt mode
needs to access registers at address offset near 0x10000. These
registers are private DMC performance counters, which might be used
as interrupt trigger when overflow. Potential usage is to skip polling
in devfreq framework and switch to interrupt managed bandwidth control.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Enable audio driver for Exynos5250 based Arndale boards to improve
testing coverage.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Enable driver for Exynos5422 Dynamic Memory Controller supporting
dynamic frequency and voltage scaling in Exynos5422 SoCs.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add sound node and the clock configurations for the I2S controller
for audio support on the Exynos5250 SoC Arndale boards with
WM1811 based audio daughter board.
We need to increase drive strength of the I2S bus, otherwise
the audio CODEC doesn't work. Likely the CODEC's master clock
is the main issue here.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Replace hard-coded number with appropriate define for GIC SPI or PPI
specifier in interrupt. This makes code easier to read. No expected
functionality change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Multi Core Timer node has interrupts routed to two different parents -
GIC and combiner. This was modeled with a interrupt-map within a
subnode but can be expressed in an easier and more common way, directly
in the node itself.
Tested on Odroid XU (Exynos5410), Odroid HC1 (Exynos5422) and Arndale
Octa (Exynos5420).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Multi Core Timer node has interrupts routed to two different parents -
GIC and combiner. This was modeled with a interrupt-map within a
subnode but can be expressed in an easier and more common way, directly
in the node itself.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Multi Core Timer node has interrupts routed to two different parents -
GIC and combiner. This was modeled with a interrupt-map within a
subnode but can be expressed in an easier and more common way, directly
in the node itself.
Tested on Odroid U3 (Exynos4412).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Multi Core Timer node has interrupts routed to two different parents -
GIC and combiner. This was modeled with a interrupt-map within a
subnode but can be expressed in an easier and more common way, directly
in the node itself.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
The device node name should reflect generic class of a device so rename
the Multi Core Timer node from "mct" to "timer". This will be also in
sync with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Change representation of phandle array as then dt-schema counts number
of its items properly.
Signed-off-by: Maciej Falkowski <m.falkowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
In commit 7222e8db2d50 ("iommu/exynos: Fix build errors") Exynos3250
IOMMU driver stopped supporting two IRQ lines. The second IRQ line in
DTS is ignored and is not needed.
Signed-off-by: Maciej Falkowski <m.falkowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The Exynos5422 SoC used on Odroid XU3 Lite boards belongs to a special
ASV bin but this information cannot be read from the Chip ID block
registers. Add samsung,asv-bin property for XU3 Lite to ensure the ASV
bin is properly determined.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The Chip ID block in addition to exact chip revision information
contains data and control registers for ASV (Adaptive Supply Voltage)
and ABB (Adaptive Body Bias). Add "syscon" compatible so the Chip ID
block can be shared by respective drivers.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
All CortexA7/A15 based Exynos5 SoCs have ARM architected timers, so enable
support for them directly in the base dtsi. None of the known firmware
properly configures CNTFRQ arch timer register, so force clock frequency
to 24MHz, which is the only configuration supported by the remaining
clock drivers so far.
Stock firmware for Peach Pit and Pi Chromebooks also doesn't reset
properly other arch timer registers, so add respective properties
indicating that. Other Exynos5-based boards behaves correctly in this area,
what finally allows to enable support for KVM-based virtualization.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Today the EFI runtime functions are setup in architecture specific
code (x86 and arm), with the functions themselves living in drivers/xen
as they are not architecture dependent.
As the setup is exactly the same for arm and x86 move the setup to
drivers/xen, too. This at once removes the need to make the single
functions global visible.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
[boris: "Dropped EXPORT_SYMBOL_GPL(xen_efi_runtime_setup)"]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
IPQ4019 has a built in SD/eMMC controller which is supported by the
SDHCI MSM driver, by the "qcom,sdhci-msm-v4" binding.
So lets add the appropriate node for it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
arm64 shares some code under arch/arm/xen, including mm.c.
However ZONE_DMA is removed by commit
ad67f5a6545("arm64: replace ZONE_DMA with ZONE_DMA32").
So add a check if CONFIG_ZONE_DMA32 is enabled use __GFP_DMA32.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
|
|
Add Pincfgs to enable the i.MX6's OTG feature for UDOO
Signed-off-by: Markus Kueffner <kueffner.markus@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds the possibility to wake the module with an external signal
as defined in the Colibri standard
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63
and move the inactive flexcan nodes to imx6ull-colibri-eval-v3.dtsi
where they belong.
Note that this commit does not enable flexcan functionality, but rather
eases the effort needed to do so.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds the watchdog to the imx6ull-colibri devicetree
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Reduce the current drawn from VCC_BATT when the main power on the 3V3
pins to the module are switched off.
This switches off SoC internal pull resistors which are provided on the
module for TAMPER7 and TAMPER9 SoC pin and switches on a pull down
instead of a pullup for the USBC_DET module pin (TAMPER2).
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Do not change the clock as the power for this phy is switched
with that clock.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds some missing pinmuxing that is in the colibri
standard to the dts.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This commit adds the touchscreen from Toradex so one can enable it.
It is disabled by default because the pins are also used for PWM<B>,
PWM<C>, aka pwm2, pwm3 which is the standard use for colibri boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch prepares the devicetree for the new Ixora V1.2 where we are
able to turn off the supply of the can transceiver. This implies to use
a sleep state on transmission pins in order to prevent backfeeding.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds the muxing for the optional pins usb-oc (overcurrent) and
usb-id.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
