summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2019-10-28ARM: dts: vf-colibri: add recovery mode to i2cPhilippe Schenker
This patch enables the recovery mode now available. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-28ARM: dts: imx*(colibri|apalis): add missing recovery modes to i2cPhilippe Schenker
This patch adds missing i2c recovery modes and corrects wrongly named ones. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-28ARM: dts: imx6-logicpd: Re-enable SNVS power keyAdam Ford
The baseboard of the Logic PD i.MX6 development kit has a power button routed which can both power down and power up the board. It can also wake the board from sleep. This functionality was marked as disabled by default in imx6qdl.dtsi, so it needs to be explicitly enabled for each board. This patch enables the snvs power key again. Signed-off-by: Adam Ford <aford173@gmail.com> Fixes: 770856f0da5d ("ARM: dts: imx6qdl: Enable SNVS power key according to board design") Cc: stable <stable@vger.kernel.org> #5.3+ Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-28ARM: dts: imx6dl-yapp4: Enable the I2C3 bus on all board variantsMichal Vokáč
imx6dl-yapp4 Draco and Ursa boards use the I2C3 bus to control some external devices through the /dev files. So enable the I2C3 bus on all board variants, not just on Hydra. Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-28ARM: dts: imx6dl-yapp4: Enable UART2Michal Vokáč
The second UART is needed for 3D or MFD printer control. Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-27ARM: 8917/1: mm: include <asm/set_memory.h>Ben Dooks (Codethink)
The definitions of set_kernel_text_rw() and set_kernel_text_ro() are in <asm/set_memory.h> but this is not included in init.c which defines these. Silence the following warnings by including the <asm/set_memory.h> header. arch/arm/mm/init.c:669:6: warning: symbol 'set_kernel_text_rw' was not declared. Should it be static? arch/arm/mm/init.c:678:6: warning: symbol 'set_kernel_text_ro' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2019-10-27ARM: 8916/1: mm: make set_section_perms() staticBen Dooks (Codethink)
The set_section_perms() is not defined outside of the init.c file, so make it static to avoid the following warning: arch/arm/mm/init.c:596:6: warning: symbol 'set_section_perms' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2019-10-27ARM: 8915/1: zImage: atags_to_fdt: fix __be32 and __be64 typesBen Dooks (Codethink)
There are some sparse warnings about type conversion in the atags_to_fdt.c code, due to __be32 and __be64, so fix the following: - Change _be32 and __be64 where appropriate - Change setprop() to take a 'void *' - Change incorrect fdt32_to_cpu() on FDT_MAGIC Fixes the following sparse warnings: arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32 arch/arm/boot/compressed/atags_to_fdt.c:182:60: warning: incorrect type in assignment (different base types) arch/arm/boot/compressed/atags_to_fdt.c:182:60: expected unsigned long long [usertype] arch/arm/boot/compressed/atags_to_fdt.c:182:60: got restricted __be64 [usertype] arch/arm/boot/compressed/atags_to_fdt.c:184:60: warning: incorrect type in assignment (different base types) arch/arm/boot/compressed/atags_to_fdt.c:184:60: expected unsigned long long [usertype] arch/arm/boot/compressed/atags_to_fdt.c:184:60: got restricted __be64 [usertype] arch/arm/boot/compressed/atags_to_fdt.c:187:62: warning: incorrect type in assignment (different base types) arch/arm/boot/compressed/atags_to_fdt.c:187:62: expected unsigned int arch/arm/boot/compressed/atags_to_fdt.c:187:62: got restricted __be32 [usertype] arch/arm/boot/compressed/atags_to_fdt.c:189:62: warning: incorrect type in assignment (different base types) arch/arm/boot/compressed/atags_to_fdt.c:189:62: expected unsigned int arch/arm/boot/compressed/atags_to_fdt.c:189:62: got restricted __be32 [usertype] Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2019-10-27ARM: 8913/1: arch_timer: include <asm/arch_timer.h>Ben Dooks
The arch_timer_arch_init is defined in <asm/arch_timer.h> so include that to fix the following sparse error: arch/arm/kernel/arch_timer.c:31:12: warning: symbol 'arch_timer_arch_init' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2019-10-27ARM: 8911/1: move pcibios_report_status to <asm/pci.h>Ben Dooks
Move the pcibios_report_status to <asm/pci.h> include to remove the following sparse warning and to remove the extra definition in the footbrdige dc21285.c driver: arch/arm/kernel/bios32.c:59:6: warning: symbol 'pcibios_report_status' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2019-10-27ARM: 8910/1: fix missing declartion of module_frob_arch_sectionsBen Dooks
The module_frob_arch_sections function is missing the header declaration which is in <linux/moduleloader.h> so include that to fix the following sparse warning: arch/arm/kernel/module-plts.c:188:5: warning: symbol 'module_frob_arch_sections' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2019-10-27ARM: 8909/1: make unexported items staticBen Dooks
Fixup the following sparse warnings by making the functions and structures static. arch/arm/mm/dma-mapping.c:1562:6: warning: symbol '__arm_iommu_free_attrs' was not declared. Should it be static? arch/arm/mm/dma-mapping.c:1586:6: warning: symbol 'arm_iommu_free_attrs' was not declared. Should it be static? arch/arm/mm/dma-mapping.c:1592:6: warning: symbol 'arm_coherent_iommu_free_attrs' was not declared. Should it be static? arch/arm/mm/dma-mapping.c:1716:5: warning: symbol 'arm_coherent_iommu_map_sg' was not declared. Should it be static? arch/arm/mm/dma-mapping.c:1734:5: warning: symbol 'arm_iommu_map_sg' was not declared. Should it be static? arch/arm/mm/dma-mapping.c:1767:6: warning: symbol 'arm_coherent_iommu_unmap_sg' was not declared. Should it be static? arch/arm/mm/dma-mapping.c:1784:6: warning: symbol 'arm_iommu_unmap_sg' was not declared. Should it be static? arch/arm/mm/dma-mapping.c:1798:6: warning: symbol 'arm_iommu_sync_sg_for_cpu' was not declared. Should it be static? arch/arm/mm/dma-mapping.c:1816:6: warning: symbol 'arm_iommu_sync_sg_for_device' was not declared. Should it be static? arch/arm/mm/dma-mapping.c:2018:26: warning: symbol 'iommu_ops' was not declared. Should it be static? arch/arm/mm/dma-mapping.c:2040:26: warning: symbol 'iommu_coherent_ops' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2019-10-27ARM: 8907/1: arch: reuse addr variable in pfn_validClemens Gruber
Avoid calling __pfn_to_phys twice. Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2019-10-27Merge 5.4-rc5 into tty-nextGreg Kroah-Hartman
We want the tty/serial fix in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-27ARM: dts: msm8974: thermal: Add thermal zones for each sensorAmit Kucheria
msm8974 has 11 sensors connected to a single TSENS IP. Define a thermal zone for each of those sensors to expose the temperature of each zone. Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org> Tested-by: Brian Masney <masneyb@onstation.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Andy Gross <agross@kernel.org>
2019-10-27ARM: dts: msm8974: thermal: Add interrupt supportAmit Kucheria
Register upper-lower interrupt for the tsens controller. Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org> Tested-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Andy Gross <agross@kernel.org>
2019-10-26ARM: dts: imx6qdl-rex: add gpio expander pca9535Gilles DOFFE
The pca9535 gpio expander is present on the Rex baseboard, but missing from the dtsi. The pca9535 is on i2c2 bus which is common to the three SOM variants (Basic/Pro/Ultra), thus it is activated by default. Add also the new gpio controller and the associated interrupt line MX6QDL_PAD_NANDF_CS3__GPIO6_IO16. Signed-off-by: Gilles DOFFE <gilles.doffe@savoirfairelinux.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-26ARM: dts: imx6ul-14x14-evk.dtsi: configure USBOTG1 ID pinctrlPeter Chen
Without configuring this pinctrl, the ID value can't be got correctly, then, the dual-role switch can't work well. Signed-off-by: Peter Chen <peter.chen@nxp.com> Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-26ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interruptsFabio Estevam
Since commit a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors") a storm of accelerometer interrupts is seen: [ 114.211283] irq 260: nobody cared (try booting with the "irqpoll" option) [ 114.218108] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.4 #1 [ 114.223960] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 114.230531] [<c0112858>] (unwind_backtrace) from [<c010cdc8>] (show_stack+0x10/0x14) [ 114.238301] [<c010cdc8>] (show_stack) from [<c0c1aa1c>] (dump_stack+0xd8/0x110) [ 114.245644] [<c0c1aa1c>] (dump_stack) from [<c0193594>] (__report_bad_irq+0x30/0xc0) [ 114.253417] [<c0193594>] (__report_bad_irq) from [<c01933ac>] (note_interrupt+0x108/0x298) [ 114.261707] [<c01933ac>] (note_interrupt) from [<c018ffe4>] (handle_irq_event_percpu+0x70/0x80) [ 114.270433] [<c018ffe4>] (handle_irq_event_percpu) from [<c019002c>] (handle_irq_event+0x38/0x5c) [ 114.279326] [<c019002c>] (handle_irq_event) from [<c019438c>] (handle_level_irq+0xc8/0x154) [ 114.287701] [<c019438c>] (handle_level_irq) from [<c018eda0>] (generic_handle_irq+0x20/0x34) [ 114.296166] [<c018eda0>] (generic_handle_irq) from [<c0534214>] (mxc_gpio_irq_handler+0x30/0xf0) [ 114.304975] [<c0534214>] (mxc_gpio_irq_handler) from [<c0534334>] (mx3_gpio_irq_handler+0x60/0xb0) [ 114.313955] [<c0534334>] (mx3_gpio_irq_handler) from [<c018eda0>] (generic_handle_irq+0x20/0x34) [ 114.322762] [<c018eda0>] (generic_handle_irq) from [<c018f3ac>] (__handle_domain_irq+0x64/0xe0) [ 114.331485] [<c018f3ac>] (__handle_domain_irq) from [<c05215a8>] (gic_handle_irq+0x4c/0xa8) [ 114.339862] [<c05215a8>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98) [ 114.347361] Exception stack(0xc1301ec0 to 0xc1301f08) [ 114.352435] 1ec0: 00000001 00000006 00000000 c130c340 00000001 c130f688 9785636d c13ea2e8 [ 114.360635] 1ee0: 9784907d 0000001a eaf99d78 0000001a 00000000 c1301f10 c0182b00 c0878de4 [ 114.368830] 1f00: 20000013 ffffffff [ 114.372349] [<c0101a70>] (__irq_svc) from [<c0878de4>] (cpuidle_enter_state+0x168/0x5f4) [ 114.380464] [<c0878de4>] (cpuidle_enter_state) from [<c08792ac>] (cpuidle_enter+0x28/0x38) [ 114.388751] [<c08792ac>] (cpuidle_enter) from [<c015ef9c>] (do_idle+0x224/0x2a8) [ 114.396168] [<c015ef9c>] (do_idle) from [<c015f3b8>] (cpu_startup_entry+0x18/0x20) [ 114.403765] [<c015f3b8>] (cpu_startup_entry) from [<c1200e54>] (start_kernel+0x43c/0x500) [ 114.411958] handlers: [ 114.414302] [<a01028b8>] irq_default_primary_handler threaded [<fd7a3b08>] mma8452_interrupt [ 114.422974] Disabling IRQ #260 CPU0 CPU1 .... 260: 100001 0 gpio-mxc 31 Level mma8451 The MMA8451 interrupt triggers as low level, so the GPIO6_IO31 pin needs to activate its pull up, otherwise it will stay always at low level generating multiple interrupts. The current device tree does not configure the IOMUX for this pin, so it uses whathever comes configured from the bootloader. The IOMUXC_SW_PAD_CTL_PAD_EIM_BCLK register value comes as 0x8000 from the bootloader, which has PKE bit cleared, hence disabling the pull-up. Instead of relying on a previous configuration from the bootloader, configure the GPIO6_IO31 pin with pull-up enabled in order to fix this problem. Fixes: a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors") Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-By: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-26ARM: hisi: drop useless depend on ARCH_MULTI_V7Kefeng Wang
The ARCH_HISI depends on ARCH_MULTI_V7, no need to add this depend to each sub-menu config, and use tabs where possible. Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
2019-10-25Merge tag 'armsoc-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Olof Johansson: "A slightly larger set of fixes have accrued in the last two weeks. Mostly a collection of the usual smaller fixes: - Marvell Armada: USB phy setup issues on Turris Mox - Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some maintainer updates. - OMAP: Fixlets for display config, interrupt settings for wifi, some clock/PM pieces. Also IOMMU regression fix and a ti-sysc no-watchdog regression fix. - i.MX: A few fixes around PM/settings, some devicetree fixlets and catching up with config option changes in DRM - Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display panel settings ... and some smaller fixes for Davinci (backlight, McBSP DMA), Allwinner (phy regulators, PMU removal on A64, etc)" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits) ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157 MAINTAINERS: Update the Spreadtrum SoC maintainer MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue bus: ti-sysc: Fix watchdog quirk handling ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs ARM: davinci_all_defconfig: enable GPIO backlight ARM: davinci: dm365: Fix McBSP dma_slave_map entry ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk ARM: dts: imx7s: Correct GPT's ipg clock source ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect' ARM: dts: imx6q-logicpd: Re-Enable SNVS power key arm64: dts: lx2160a: Correct CPU core idle state name mailmap: Add Simon Arlott (replacement for expired email address) arm64: dts: rockchip: Fix override mode for rk3399-kevin panel ...
2019-10-25ARM: multi_v7_defconfig: Enable audio support for stm32mp157Olivier Moysan
This commits enable (as module): - STM32 SAI and I2S configs used on stm32mp157. - Cirrus CS42L51 audio codec for stm32mp157a-dk1 board. - Audio graph card support for stm32mp157a-dk1 board. Link: https://lore.kernel.org/r/20191025125632.11057-1-alexandre.torgue@st.com Signed-off-by: Olivier Moysan <olivier.moysan@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2019-10-25ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157Patrice Chotard
Relax qspi pins slew-rate to minimize peak currents. Fixes: 844030057339 ("ARM: dts: stm32: add flash nor support on stm32mp157c eval board") Link: https://lore.kernel.org/r/20191025130122.11407-1-alexandre.torgue@st.com Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2019-10-25ARM: dts: stm32: remove useless dma-ranges property for stm32f469Benjamin Gaignard
Remove dma-ranges from ltdc node since it is already set on bus node. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: remove useless dma-ranges property for stm32f429Benjamin Gaignard
Remove dma-ranges from ltdc node since it is already set on bus node. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: disable active-discharge for vbus_otg on stm32mp157a-avenger96Pascal Paillet
Active discharge is not needed on vbus_otg and generate unneeded current consumption. Signed-off-by: Pascal Paillet <p.paillet@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: Fix active discharge usage on stm32mp157Pascal Paillet
Active discharge is a uint32 not a boolean. Signed-off-by: Pascal Paillet <p.paillet@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: change default minimal buck1 value on stm32mp157Pascal Paillet
Minimal value is the value set during boot or before suspend. We must ensure that the value is a functional value to boot. Signed-off-by: Pascal Paillet <p.paillet@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: add PWR regulators support on stm32mp157Pascal Paillet
This patch adds support of STM32 PWR regulators on stm32mp157c. This replace dummy fixed regulators on stm32mp157c-ed1 and stm32mp157c-dk2. Signed-off-by: Pascal Paillet <p.paillet@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: remove useless interrupt from dsi node for stm32f469Benjamin Gaignard
DSI driver doesn't use interrupt, remove it from the node since it breaks yaml check. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: add hdmi audio support to stm32mp157a-dk1 boardOlivier Moysan
Add HDMI audio support through Sil9022 HDMI transceiver on stm32mp157a-dk1 board. Signed-off-by: Olivier Moysan <olivier.moysan@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: Add DAC support to stm32mp157c-ed1Fabrice Gasnier
stm32mp157c-ed1 board has digital-to-analog converter signals routed to JP11 and JP10 jumpers (e.g. PA4/PA5). It's easier then to configure them both. But keep them disabled by default, so the pins are kept in their initial state to lower power consumption. This way they can also be used as GPIO. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: Add DAC pins used on stm32mp157c-ed1Fabrice Gasnier
Define pins that can be used by digital-to-analog converter on stm32mp157c eval daughter board: - PA4 and PA5 pins are available respectively on JP11 and JP10 Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: fix regulator-sd_switch node on stm32mp157c-ed1 boardAlexandre Torgue
This commit fixes regulator-sd_switch node in order to be compliant to DT validation schema. Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: remove usb phy-names entries on stm32mp157c-ev1Alexandre Torgue
"phy-names" entries are not used. To be compliant with DT validation tool, those entries have to be remove. Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: fix joystick node on stm32f746 and stm32mp157c eval boardsAlexandre Torgue
"#size-cells" entry is not needed for "gpio-keys" driver. Indeed "reg" entry is not used. This commit will fix a warnings seen by DT validation tool. Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: fix memory nodes to match with DT validation toolAlexandre Torgue
DT validation ("make dtbs_check") has shown that some memory nodes were not correctly written. This commit fixes this kind of issue: "stm32f746-disco.dt.yaml: /: memory: False schema does not allow {'device_type': ['memory'], 'reg': [[3221225472, 8388608]]}" Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: add focaltech touchscreen on stm32mp157c-dk2 boardYannick Fertré
Enable focaltech ft6236 touchscreen on STM32MP157C-DK2 board. Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: enable ADC support on stm32mp157a-dk1Fabrice Gasnier
Configure ADC support on stm32mp157a-dk1. It can be used for various purpose: - AIN connector has several analog inputs: ANA0, ANA1, ADC2 in6 & in2, ADC1 in13 & in6 - USB Type-C CC1 & CC2 pins wired to in18 & in19 It's easier then to Configure them all. But keep them disabled by default, so the pins are kept in their initial state to lower power consumption. This way they can also be used as GPIO. Add VDD and VDDA supplies to ADC on stm32mp157c-dk1 board. This allows to get full ADC analog performances in case VDDA is below 2.7V (not the case by default). Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: add ADC pins used on stm32mp157a-dk1Fabrice Gasnier
Define pins that can be used for ADC on stm32mp157a-dk1 board: - AIN connector has ADC input pins - USB Type-C CC1 & CC2 pins (e.g. in18, in19) Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: Enable VREFBUF on stm32mp157a-dk1Fabrice Gasnier
Enable VREFBUF as ADC/DAC uses it on stm32mp157a-dk1 board. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: dts: stm32: move ltdc pinctrl on stm32mp157a dk1 boardYannick Fertré
The ltdc pinctrl must be in the display controller node and not in the peripheral node (hdmi bridge). Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-10-25ARM: shmobile: rcar-gen2: Drop legacy DT clock supportGeert Uytterhoeven
As of commit 362b334b17943d84 ("ARM: dts: r8a7791: Convert to new CPG/MSSR bindings"), all upstream R-Car Gen2 device tree source files use the unified "Renesas Clock Pulse Generator / Module Standby and Software Reset" DT bindings. Hence remove backward compatibility with old R-Car Gen2 device trees describing a hierarchical representation of the various CPG and MSTP clocks. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20191016150939.30620-1-geert+renesas@glider.be
2019-10-25ARM: dts: at91: sama5d4_xplained: add digital filter for i2cEugen Hristev
Add property for digital filter for i2c0 node sama5d4_xplained Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Link: https://lore.kernel.org/r/1568189911-31641-10-git-send-email-eugen.hristev@microchip.com Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
2019-10-25ARM: dts: at91: sama5d2_xplained: add analog and digital filter for i2cEugen Hristev
Add property for analog and digital filter for i2c1 and i2c2 nodes for sama5d2_xplained Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Link: https://lore.kernel.org/r/1568189911-31641-9-git-send-email-eugen.hristev@microchip.com Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
2019-10-25ARM: dts: Disable DMA support on the BK4 vf610 device's fsl_lpuartLukasz Majewski
This change disables the DMA support (RX/TX) on the NXP's fsl_lpuart driver - the PIO mode is used instead. This change is necessary for better robustness of BK4's device use cases with many potentially interrupted short serial transfers. Without it the driver hangs when some distortion happens on UART lines. Signed-off-by: Lukasz Majewski <lukma@denx.de> Suggested-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-25ARM: dts: imx6q-gw54xx: Do not use 'simple-audio-card,dai-link'Fabio Estevam
According to Documentation/devicetree/bindings/sound/simple-card.txt the 'simple-audio-card,dai-link' may be omitted when the card has only one DAI link, which is the case here. Get rid of 'simple-audio-card,dai-link' in order to fix the following build warning with W=1: arch/arm/boot/dts/imx6q-gw54xx.dts:19.32-31.5: Warning (unit_address_vs_reg): /sound-digital/simple-audio-card,dai-link@0: node has a unit name, but no reg property Cc: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-25ARM: dts: imx6dl-yapp4: Enable the MPR121 touchkey controller on HydraMichal Vokáč
Add the touch keyboard present on Hydra board. The controller is connected only using I2C lines. The interrupt line is not available hence we use the polling mode. Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-25ARM: dts: imx: Rename "iram" node to "sram"Krzysztof Kozlowski
The device node name should reflect generic class of a device so rename the "iram" node to "sram". This will be also in sync with upcoming DT schema. No functional change. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-24Merge tag 'omap-for-v5.5/ti-sysc-drop-pdata-v2-signed-take2' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt Drop legacy platform data for omaps for v5.5 This series of changes continues dropping legacy platform data for omaps. With the proper device tree configuration in place in the dts files for ti-sysc interconnect target module driver, we can drop the related platform data and legacy ti,hwmods custom property. Most of the patches in this series drop platform data and custom dts property one device class and one SoC at time. This way we can easily revert one patch at a time in case of unexpected issues if the fix is not trivial. For am335x musb, we need to first update the device tree to probe with ti-sysc interconnect target module driver. And then the following patches drop the legacy platform data. Note that this series depends on earlier ti-sysc related driver changes * tag 'omap-for-v5.5/ti-sysc-drop-pdata-v2-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (40 commits) ARM: OMAP2+: Drop legacy platform data for am335x musb ARM: dts: Drop pointless status changing for am3 musb ARM: dts: Probe am335x musb with ti-sysc ARM: OMAP2+: Drop legacy platform data for musb on omap4 ARM: OMAP2+: Drop legacy platform data for omap4 mcasp ARM: OMAP2+: Drop legacy platform data for am3 and am4 mcasp ARM: OMAP2+: Drop legacy platform data for dra7 rng ARM: OMAP2+: Drop legacy platform data for am3 and am4 rng ARM: OMAP2+: Drop legacy platform data for omap4 hdq1w ARM: OMAP2+: Drop legacy platform data for dra7 hdq1w ARM: OMAP2+: Drop legacy platform data for am4 hdq1w ARM: OMAP2+: Drop legacy platform data for omap5 mcbsp ARM: OMAP2+: Drop legacy platform data for omap4 mcbsp ARM: OMAP2+: Drop legacy platform data for omap5 wdt ARM: OMAP2+: Drop legacy platform data for dra7 wdt ARM: OMAP2+: Drop legacy platform data for am3 and am4 wdt ARM: dts: Drop custom hwmod property for omap5 mmc ARM: dts: Drop custom hwmod property for am4 mmc ARM: dts: Drop custom hwmod property for am3 mmc ARM: dts: Drop custom hwmod property for omap5 i2c ... Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-3 Signed-off-by: Olof Johansson <olof@lixom.net>
generated by cgit (git 2.34.1) at 2025-09-22 21:22:23 +0000