| Age | Commit message (Collapse) | Author |
|---|
|
The name should match the pattern defined in the mmc-controller binding.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202507220336.JhvVLL7k-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202507220215.wVoUMK5B-lkp@intel.com/
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
This platform uses the same GPIO controller as Nomadik. It however has
its own pinconf & pinmux controller. EyeQ5 is the first platform to use
gpio-nomadik independently from pinctrl-nomadik.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Declare the temperature sensor on I2C bus 2. Its label is the schematics
identifier.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add the SoC I2C controller nodes to the platform devicetree. Use a
default bus frequency of 400kHz. They are AMBA devices that are matched
on PeriphID.
Set transfer timeout to 10ms instead of Linux's default of 200ms.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add the MMC/SDHCI controller found in the eyeQ5 SoC. It is based on the
cadence sd4hc controller and support modes up to HS400 enhanced strobe.
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add the MMC/SDHCI controller found in the eyeQ6 SoC. It is based on the
cadence sd4hc controller and support modes up to HS400 enhanced strobe.
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The CM3.5 device used in EyeQ6H SoCs incorrectly reports the status
for Hardware Cache Initialization (HCI). This commit adds the
compatible string for the CM to acknowledge this issue, which enables
the use of the second CPU cluster.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add a new reserved-memory node, containing bootloader config with MAC
addresses for both ethernet instances of the SoC.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20241230143035.265518-8-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change the declaration of clocks: remove all fixed clocks and declare
system-controllers (OLB) as clock providers.
Remove eyeq6h-fixed-clocks.dtsi and move the crystal clock to the main
eyeq6h.dtsi file.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Change the structure of the clock tree: rather than individual
devicetree nodes registering each fixed factor clock derived from OLB
PLLs, have the OLB node provide the necessary clocks.
Remove eyeq5-clocks.dtsi and move the three remaining "fixed-clock"s to
the main eyeq5.dtsi file.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
There is currently no eyeq6 compatible string defined in the binding
documentation. Only eyeq6h version is defined, so let's use it.
Note that there are actually no codes relying on eyeq6h; the purpose
of this patch is mainly to be coherent with the documentation.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The OLB ("Other Logic Block") is a system-controller region hosting
clock, reset and pin controllers. It contains registers such as I2C
speed mode that need to be accessible by other nodes.
Remove fixed-clocks previously used; replace references.
Add parent crystal clock, fixed at 30MHz.
Add pin nodes for all functions.
Add mobileye,eyeq5-olb compatible node, hosting clk, reset and pinctrl.
Add reset and pinctrl references to UART nodes.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
EyeQ6H (or “High”) is an other SoC from Mobileye still based on the
MIPS I6500 architecture as the EyeQ5. The 2 clusters of this SoC
contains 4 cores which are capable of running 4 threads. Besides this,
it features multiple controllers such as the classic UART, high speed
I2C, SPI, as well as CAN-FD, PCIe Gen4, Octal/Quad SPI Flash
interface, Gigabit Ethernet, MIPI CSI-2, MIPI DSI, and eMMC 5.1. It
also includes a Hardware Security Module, Functional Safety Hardware,
and video encoders and more.
This commit provides the infrastructure to build a kernel running on
EyeQ6H SoC. For now the support is limited and only one CPU core is
running.
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
EyeQ6H (or “High”) is an other SoC from Mobileye still based on the
MIPS I6500 architecture as the EyeQ5. The 2 clusters of this SoC
contains 4 cores which are capable of running 4 threads. Besides this,
it features multiple controllers such as the classic UART, high speed
I2C, SPI, as well as CAN-FD, PCIe Gen4, Octal/Quad SPI Flash
interface, Gigabit Ethernet, MIPI CSI-2, MIPI DSI, and eMMC 5.1. It
also includes a Hardware Security Module, Functional Safety Hardware,
and video encoders and more.
This commit provides the initial device tree files with support for
UART, GPIO and pinctrl, as well as fixed clocked.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add a device tree for the Mobileye EPM5 evaluation board.
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add a device tree include file for the Mobileye EyeQ5 SoC.
Based on the work of Slava Samsonov <stanislav.samsonov@intel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
