| Age | Commit message (Collapse) | Author |
|---|
|
The Kconfig for this file is:
drivers/gpio/Kconfig:config GPIO_ATH79
drivers/gpio/Kconfig: tristate "Atheros AR71XX/AR724X/AR913X GPIO support"
...but however it does not include module.h -- it in turn gets it from
another header (gpio/driver.h) and we'd like to replace that with a
forward delcaration of "struct module;" but if we do, this file will
fail to compile.
So we fix this first to avoid putting build failures into the bisect
commit history.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig for this file is:
drivers/gpio/Kconfig:config GPIO_ALTERA
drivers/gpio/Kconfig: tristate "Altera GPIO"
...but however it does not include module.h -- it in turn gets it from
another header (gpio/driver.h) and we'd like to replace that with a
forward delcaration of "struct module;" but if we do, this file will
fail to compile.
So we fix this first to avoid putting build failures into the bisect
commit history.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig for this file is:
drivers/gpio/Kconfig:config GPIO_TS4800
drivers/gpio/Kconfig: tristate "TS-4800 DIO blocks and compatibles"
...but however it does not include module.h -- it in turn gets it from
another header (gpio/driver.h) and we'd like to replace that with a
forward delcaration of "struct module;" but if we do, this file will
fail to compile.
So we fix this first to avoid putting build failures into the bisect
commit history.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This file is currently getting module.h from a global gpio header
and it will faii to build once we remove module.h from that.
However, the driver is controlled with the following Kconfig:
drivers/gpio/Kconfig:config GPIO_SX150X
drivers/gpio/Kconfig: bool "Semtech SX150x I2C GPIO expander"
and hence the two lines of MODULE_DEVICE_TABLE are no-ops that
can simply be deleted.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This file is currently getting module.h from a global gpio header
and it will fail to build once we remove module.h from that.
However, the driver is controlled with the following Kconfig:
drivers/gpio/Kconfig:config GPIO_PALMAS
drivers/gpio/Kconfig: bool "TI PALMAS series PMICs GPIO"
and hence the line of MODULE_DEVICE_TABLE is a no-op that can simply
be deleted. In fact it should have been removed in an earlier commit
that did demodularization, however the unseen include prevented my
build testing from detecting it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts commit 313b9a9938bf4076425741121d5d766826793e5d.
This was already fixed by
commit bf62efeb164343916ebb89dca6dfe5e6b6751700
"gpio: pca954x: fix undefined error code from remove"
The latter is a better fix since it makes it easier to detect
erronous code by not assigning a default error code.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The build complains about missing MODULE_LICENSE() in
the Aspeed GPIO driver. The license is evident from the
file header, put in "GPL".
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alistair Popple <alistair@popple.id.au>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Follow DT and forbid default trigger if the GPIO irqchip device is
enumerated from ACPI. Triggering for these devices will be configured
automatically from ACPI interrupt resources provided by the BIOS.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use devm_gpiochip_add_data() for GPIO registration and remove the need
of driver callback .remove.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into devel
Immutable branch between MFD, GPIO and Regulator due for the v4.9 merge window
|
|
ret is not initialized so it contains garbage. Ensure garbage
is not returned in the case that pdata && pdata->teardown is false
by initializing ret to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch switches the driver to use the generic GPIO MMIO functions
that removes a bit of redundant and duplicate code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Both gpio_export and gpio_free APIs are obsolete now.
Signed-off-by: Amitesh Singh <singh.amitesh@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pca953x_gpio_set_multiple() has some coding style issues that make it
harder to read. Tweak the code a bit.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The chip_type variable in struct pca953x_chip is no longer required.
Remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Avoid the unnecessary if-else in pca953x_read_regs() by spltting the
routine into smaller, specialized functions and calling the right one
via a function pointer held in struct pca953x.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Avoid the unnecessary if-else in pca953x_write_regs() by splitting
the routine into smaller, specialized functions and calling the right
one via a function pointer held in struct pca953x_chip.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There are multiple places in the driver code where a
switch (chip->chip_type) is used to determine the proper register
offset.
Unduplicate the code by adding a simple structure holding the possible
offsets that differ between the pca953x and pca957x chip families and
use it to avoid the checks.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
ARM LPC32xx platform is device-tree only, there is no need to keep
a file with GPIO platform data structures, however some of macro
definitions should be moved to the driver code, which is the only user
of the removed header file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Using a default trigger is a bad idea if using DT to configure
interrupts, as the device's interrupt specifier will always contain
the trigger configuration.
Let's warn about that particular situation, and revert to not
having a default. Hopefully, the couple of drivers still using
this feature will quickly be fixed.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
R-Car Gen3's GPIO blocks are identical to Gen2's in every respect.
Based on work for the r8a7795 (R-Car H3) by Ulrich Hecht.
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Aspeed SoCs contain GPIOs banked by letter, where each bank contains
8 pins. The GPIO banks are then grouped in sets of four in the register
layout.
The implementation exposes multiple banks through the one driver and
requests and releases pins via the pinctrl subsystem. The hardware
supports generation of interrupts from all GPIO-capable pins.
A number of hardware features are not yet supported: Configuration of
interrupt direction (ARM or LPC), debouncing, and WDT reset tolerance
for output ports.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The recent addition of the regulator support has led to the pca953x_remove
function returning uninitialized data when no platform data pointer is
provided, as gcc warns when using -Wmaybe-uninitialized:
drivers/gpio/gpio-pca953x.c: In function 'pca953x_remove':
drivers/gpio/gpio-pca953x.c:860:9: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This restores the previous behavior, returning 0 on success.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: e23efa311110 ("gpio: pca954x: Add vcc regulator and enable it")
Acked-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add driver for lp873x PMIC family GPOs. Two GPOs are supported
and can be configured in Open-drain output or Push-pull output.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_VF610
drivers/gpio/Kconfig: def_bool y
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is now contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_SPEAR_SPICS
drivers/gpio/Kconfig: bool "ST SPEAr13xx SPI Chip Select as GPIO support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is now contained at the top of the file in the comments.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_MXC
drivers/gpio/Kconfig: def_bool y
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Note the original e-mail had a missing/typo'd @ symbol anyway.
We don't replace module.h with init.h since the file already has that.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Juergen Beisert <kernel@pengutronix.de>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_MSIC
drivers/gpio/Kconfig: bool "Intel MSIC mixed signal gpio support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds .get_direction method for the gpio_chip structure
of the wcove_gpio driver.
Signed-off-by: Bin Gao <bin.gao@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This driver is generic and aims to support all Technologic Systems's
boards embedding FPGA GPIOs with an I2C interface.
This driver supports TS-4900, TS-7970, TS-7990 and TS-4100 series.
Signed-off-by: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The if...else... block after the loop can be dropped with
a slight refactoring.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds support for the GPIO found in Broadcom's bcm63xx-gpio
chips.
This GPIO controller is used in the following Broadcom SoCs: BCM6338, BCM6345.
It can be used in newer SoCs, without the capability of pin multiplexing.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into devel
Immutable branch between MFD and GPIO due for the v4.9 merge window
|
|
The Diamond Systems GPIO-MM device features 48 lines of digital I/O via
the emulation of dual 82C55A PPI chips. This driver provides GPIO
support for these 48 channels of digital I/O. The base port addresses
for the devices may be configured via the base array module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch introduces a separate GPIO driver for Intel WhiskeyCove PMIC.
This driver is based on gpio-crystalcove.c.
Changes in v7:
- Fixed various coding style comments from Andy Shevchenko
Changes in v6:
- Removed unnecessary wcove_gpio_remove()
- Used devm_gpiochip_remove() instead of gpiochip_remove()
- Various coding style changes per Mika's comment
Changes in v5:
- Revisited the interrupt handler code to iterate until all pending
interrupts are handled. This change is to avoid missing interrupt
when we're inside the interrupt handler.
- Used regmap_bulk_read() to read address adjacent registers.
Changes in v4:
- Converted CTLI_INTCNT_XX macros to less verbose ones INT_DETECT_XX.
- Add comments about why there is no .pm for the driver.
- Header files re-ordered.
- Various coding style change to address Andy's comments.
Changes in v3:
- Fixed the year in copyright line(2015-->2016).
- Removed DRV_NAME macro.
- Added kernel-doc for regmap_irq_chip of the wcove_gpio structure.
- Line length fix.
Changes in v2:
- Typo fix (Whsikey --> Whiskey).
- Included linux/gpio/driver.h instead of linux/gpio.h
- Implemented .set_single_ended().
- Added GPIO register description.
- Replaced container_of() with gpiochip_get_data().
- Removed unnecessary "if (gpio > WCOVE_VGPIO_NUM" check.
- Removed the device id table and added MODULE_ALIAS().
Signed-off-by: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Signed-off-by: Bin Gao <bin.gao@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The AXP209 PMIC has a bunch of GPIOs accessible, that are usually used to
control LEDs or backlight.
Add a driver for them
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some i2c gpio devices are connected to a switchable power supply
which needs to be enabled prior to probing the device. This patch
allows the drive to enable the devices vcc regulator prior to probing.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The particularities of this variant are:
- GPIO_XXX_LSB and GPIO_XXX_MSB memory locations are inverted compared
to other variants.
- There is no Edge detection, Rising Edge and Falling Edge registers.
- IRQ flags are cleared when read, no need to write in Status register.
Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset
This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.
For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
On STMPE801/1801 datasheets, it's mentionned writing
in interrupt status register has no effect, bits are
cleared when reading.
Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
By cross-checking STMPE 610/801/811/1601/2401/2403 datasheets,
it appears that edge detection and rising/falling edge detection
is not supported by all STMPE variant:
GPIO GPIO
Edge detection rising/falling
edge detection
610 | X | X |
801 | | |
811 | X | X |
1600 | | |
1601 | X | X |
1801 | | X |
2401 | X | X |
2403 | X | X |
Rework stmpe_dbg_show_one() and stmpe_gpio_irq to correctly
take these cases into account.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The GPIOLIB is now selectable explicitly, and always available
for all archs. All archs that require GPIOLIB are switched to
select GPIOLIB directly. Delete the hairy ARCH_REQUIRE_GPIOLIB
and ARCH_WANTS_OPTIONAL_GPIOLIB Kconfig symbols.
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.8 kernel cycle. The big
news is the completion of the chardev ABI which I'm very happy about
and apart from that it's an ordinary, quite busy cycle. The details
are below.
The patches are tested in linux-next for some time, patches to other
subsystem mostly have ACKs.
I got overly ambitious with configureing lines as input for IRQ lines
but it turns out that some controllers have their interrupt-enable and
input-enabling in orthogonal settings so the assumption that all IRQ
lines are input lines does not hold. Oh well, revert and back to the
drawing board with that.
Core changes:
- The big item is of course the completion of the character device
ABI. It has now replaced and surpassed the former unmaintainable
sysfs ABI: we can now hammer (bitbang) individual lines or sets of
lines and read individual lines or sets of lines from userspace,
and we can also register to listen to GPIO events from userspace.
As a tie-in we have two new tools in tools/gpio: gpio-hammer and
gpio-event-mon that illustrate the proper use of the new ABI. As
someone said: the wild west days of GPIO are now over.
- Continued to remove the pointless ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
Kconfig symbols. I'm patching hexagon, openrisc, powerpc, sh,
unicore, ia64 and microblaze. These are either ACKed by their
maintainers or patched anyways after a grace period and no response
from maintainers.
Some archs (ARM) come in from their trees, and others (x86) are
still not fixed, so I might send a second pull request to root it
out later in this merge window, or just defer to v4.9.
- The GPIO tools are moved to the tools build system.
New drivers:
- New driver for the MAX77620/MAX20024.
- New driver for the Intel Merrifield.
- Enabled PCA953x for the TI PCA9536.
- Enabled PCA953x for the Intel Edison.
- Enabled R8A7792 in the RCAR driver.
Driver improvements:
- The STMPE and F7188x now supports the .get_direction() callback.
- The Xilinx driver supports setting multiple lines at once.
- ACPI support for the Vulcan GPIO controller.
- The MMIO GPIO driver supports device tree probing.
- The Acer One 10 is supported through the _DEP ACPI attribute.
Cleanups:
- A major cleanup of the OF/DT support code. It is way easier to
read and understand now, probably this improves performance too.
- Drop a few redundant .owner assignments.
- Remove CLPS711x boardfile support: we are 100% DT"
* tag 'gpio-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (67 commits)
MAINTAINERS: Add INTEL MERRIFIELD GPIO entry
gpio: dwapb: add missing fwnode_handle_put() in dwapb_gpio_get_pdata()
gpio: merrifield: Protect irq_ack() and gpio_set() by lock
gpio: merrifield: Introduce GPIO driver to support Merrifield
gpio: intel-mid: Make it depend to X86_INTEL_MID
gpio: intel-mid: Sort header block alphabetically
gpio: intel-mid: Remove potentially harmful code
gpio: rcar: add R8A7792 support
gpiolib: remove duplicated include from gpiolib.c
Revert "gpio: convince line to become input in irq helper"
gpiolib: of_find_gpio(): Don't discard errors
gpio: of: Allow overriding the device node
gpio: free handles in fringe cases
gpio: tps65218: Add platform_device_id table
gpio: max77620: get gpio value based on direction
gpio: lynxpoint: avoid potential warning on error path
tools/gpio: add install section
tools/gpio: move to tools buildsystem
gpio: intel-mid: switch to devm_gpiochip_add_data()
gpio: 74x164: Use spi_write() helper instead of open coding
...
|
|
fwnode_handle_put() should be used when terminating
device_for_each_child_node() iteration with break or
return to prevent stale device node references from
being left behind.
Generated by Coccinelle.
Fixes: 4ba8cfa79f44 ("gpio: dwapb: convert device node to fwnode")
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is a potential race when two threads do the writes to the same register
in parallel.
Prevent out of order in such case by protecting I/O access by spin lock.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Intel Merrifield platform has a special GPIO controller to
drive pads when they are muxed in corresponding mode.
Intel Merrifield GPIO IP is slightly different here and there
in comparison to the older Intel MID platforms. These differences
include in particular the shaked register offsets, specific
support of level triggered interrupts and wake capable sources,
as well as a pinctrl which is a separate IP.
Instead of uglifying existing driver I decide to provide a new
one slightly based on gpio-intel-mid.c. So, anyone can easily
compare what changes are happened to be here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Brian J Wood <brian.j.wood@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This GPIO controller is a part of Intel MID platforms which are somehow
different to pure PCs. Thus, there is no need that driver is compiled for them.
Replace dependency to X86_INTEL_MID.
While here, fix capitalization of MID abbreviation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Sort the header inclusion lines by alphabetical order.
While here, update Intel Copyright.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The commit d56d6b3d7d69 ("gpio: langwell: add Intel Merrifield support")
doesn't look at all as a proper support for Intel Merrifield and I dare to say
that it distorts the behaviour of the hardware.
The register map is different on Intel Merrifield, i.e. only 6 out of 8
register have the same purpose but none of them has same location in the
address space. The current case potentially harmful to existing hardware since
it's poking registers on wrong offsets and may set some pin to be GPIO output
when connected hardware doesn't expect such.
Besides the above GPIO and pinctrl on Intel Merrifield have been located in
different IP blocks. The functionality has been extended as well, i.e. added
support of level interrupts, special registers for wake capable sources and
thus, in my opinion, requires a completele separate driver.
If someone wondering the existing gpio-intel-mid.c would be converted to actual
pinctrl (which by the fact it is now), though I wouldn't be a volunteer to do
that.
Fixes: d56d6b3d7d69 ("gpio: langwell: add Intel Merrifield support")
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
