| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Just two driver fixes"
* tag 'i2c-for-6.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: ocores: generate stop condition after timeout in polling mode
i2c: mchp-pci1xxxx: Update Timing registers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix interaction between fw_devlink and DT overlays causing devices to
not be probed
- Fix the compatible string for loongson,cpu-interrupt-controller
* tag 'devicetree-fixes-for-6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
treewide: Fix probing of devices in DT overlays
dt-bindings: interrupt-controller: loongarch: Fix mismatched compatible
|
|
If pm_runtime_get() fails in .remove() the driver used to return the
error to the driver core. The only effect of this (compared to returning
zero) is a generic warning that the error value is ignored.
So emit a better warning and return zero to suppress the generic (and
little helpful) message. Also disable runtime PM in the error case.
This prepares changing platform device remove callbacks to return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The Cadence I2C controller has an external reset signal that needs to be
de-asserted before the I2C controller can be used.
Add support to the driver to be able to take the peripheral out of reset
using the reset controller API. The reset is optional in the driver for
compatibility to systems where the reset managed by the bootloader.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add support for the I2C units found in the MediaTek MT7981 and MT7988
SoCs. Just like other recent MediaTek I2C units that also uses v3
register offsets (which differ from v2 only by OFFSET_SLAVE_ADDR being
0x94 instead of 0x4).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In polling mode, no stop condition is generated after a timeout. This
causes SCL to remain low and thereby block the bus. If this happens
during a transfer it can cause slaves to misinterpret the subsequent
transfer and return wrong values.
To solve this, pass the ETIMEDOUT error up from ocores_process_polling()
instead of setting STATE_ERROR directly. The caller is adjusted to call
ocores_process_timeout() on error both in polling and in IRQ mode, which
will set STATE_ERROR and generate a stop condition.
Fixes: 69c8c0c0efa8 ("i2c: ocores: add polling interface")
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When loading a DT overlay that creates a device, the device is not
probed, unless the DT overlay is unloaded and reloaded again.
After the recent refactoring to improve fw_devlink, it no longer depends
on the "compatible" property to identify which device tree nodes will
become struct devices. fw_devlink now picks up dangling consumers
(consumers pointing to descendent device tree nodes of a device that
aren't converted to child devices) when a device is successfully bound
to a driver. See __fw_devlink_pickup_dangling_consumers().
However, during DT overlay, a device's device tree node can have
sub-nodes added/removed without unbinding/rebinding the driver. This
difference in behavior between the normal device instantiation and
probing flow vs. the DT overlay flow has a bunch of implications that
are pointed out elsewhere[1]. One of them is that the fw_devlink logic
to pick up dangling consumers is never exercised.
This patch solves the fw_devlink issue by marking all DT nodes added by
DT overlays with FWNODE_FLAG_NOT_DEVICE (fwnode that won't become
device), and by clearing the flag when a struct device is actually
created for the DT node. This way, fw_devlink knows not to have
consumers waiting on these newly added DT nodes, and to propagate the
dependency to an ancestor DT node that has the corresponding struct
device.
Based on a patch by Saravana Kannan, which covered only platform and spi
devices.
[1] https://lore.kernel.org/r/CAGETcx_bkuFaLCiPrAWCPQz+w79ccDp6=9e881qmK=vx3hBMyg@mail.gmail.com
Fixes: 4a032827daa89350 ("of: property: Simplify of_link_to_phandle()")
Link: https://lore.kernel.org/r/CAGETcx_+rhHvaC_HJXGrr5_WAd2+k5f=rWYnkCZ6z5bGX-wj4w@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Link: https://lore.kernel.org/r/e1fa546682ea4c8474ff997ab6244c5e11b6f8bc.1680182615.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
We need it here to apply other char/misc driver changes to.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This helper does not produce a real modalias, but tries to get the
"product" compatible part of the "vendor,product" compatibles only. It
is far from creating a purely useful modalias string and does not seem
to be used like that directly anyway, so let's try to give this helper a
more meaningful name before moving there a real modalias helper (already
existing under of/device.c).
Also update the various documentations to refer to the strings as
"aliases" rather than "modaliases" which has a real meaning in the Linux
kernel.
There is no functional change.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Wolfram Sang <wsa@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20230404172148.82422-9-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert platform_get_resource_byname(),devm_ioremap_resource() to a single
call to devm_platform_ioremap_resource_byname(), as this is exactly what
this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The maximum transfer length is a synthesis configuration parameters of the
Cadence I2C IP. Different SoCs might use different values for these
parameters.
Currently the driver has the maximum transfer length hardcoded to 255.
Trying to use the driver with an IP instance that uses smaller values for
these will work for short transfers. But longer transfers will fail.
The maximum transfer length can easily be detected at runtime since the
unused MSBs of the transfer length register are hardwired to 0. Writing
0xff and then reading back the value will give the maximum transfer length.
These changes have been tested with
1) The Xilinx MPSoC for which this driver was originally written which
has the previous hardcoded settings of 16 and 255.
2) Another instance of the Cadence I2C IP with FIFO depth of 8 and
maximum transfer length of 16.
Without these changes the latter would fail for I2C transfers longer than
16. With the updated driver both work fine even for longer transfers.
Note that the IP core and driver support chaining multiple transfers into a
single longer transfer using the HOLD bit. So the maximum transfer size is
not the limit for the length of the I2C transfer, but the limit for how
much data can be transferred without having to reprogram the control
registers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The FIFO depth is a synthesis configuration parameters of the Cadence I2C
IP. Different SoCs might use different values for these parameters.
Currently the driver has the FIFO depth hardcoded to 16. Trying to use the
driver with an IP instance that uses smaller values for these will work for
short transfers. But longer transfers will fail.
Introduce a new devicetree property that allows to describe the FIFO depth
of the I2C controller.
These changes have been tested with
1) The Xilinx MPSoC for which this driver was originally written which has
the previous hardcoded settings of 16 and 255.
2) Another instance of the Cadence I2C IP with FIFO depth of 8 and maximum
transfer length of 16.
Without these changes the latter would fail for I2C transfers longer than
8. With the updated driver both work fine even for longer transfers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
According to commit 890cc39a8799 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Update I2C timing registers based on latest hardware design.
This fix does not break functionality of chips with older design and
existing users will not be affected.
Fixes: 361693697249 ("i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch")
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
"fsl,timeout" is marked as deprecated and replaced by the
"i2c-scl-clk-low-timeout-us" i2c property.
Use this latter and, in case it is missing, for back
compatibility, check whether we still have "fsl,timeout" defined.
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
"of_property_read_u32()" is preferred to "of_get_property()" for
retrieving u32 from the device tree. Replace it.
Suggested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/i2c/busses/i2c-xiic.c:1202:39: error: ‘xiic_2_00’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/i2c/busses/i2c-synquacer.c:632:34: error: ‘synquacer_i2c_dt_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some of the bits and fields used for mailboxes communicating with the
PSP are common across all mailbox implementations (SEV, TEE, etc).
Move these bits into the common `linux/psp.h` so they don't need to
be re-defined for each implementation.
Acked-by: Rijo Thomas <Rijo-john.Thomas@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The TEE subdriver for CCP, the amdtee driver and the i2c-designware-amdpsp
drivers all include `psp-sev.h` even though they don't use SEV
functionality.
Move the definition of `__psp_pa` into a common header to be included
by all of these drivers.
Reviewed-by: Jan Dabros <jsd@semihalf.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> # For the drivers/i2c/busses/i2c-designware-amdpsp.c
Acked-by: Sumit Garg <sumit.garg@linaro.org> # For TEE subsystem bits
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Sean Christopherson <seanjc@google.com> # KVM
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The data->block[0] variable comes from user and is a number between
0-255. Without proper check, the variable may be very large to cause
an out-of-bounds when performing memcpy in slimpro_i2c_blkwr.
Fix this bug by checking the value of writelen.
Fixes: f6505fbabc42 ("i2c: add SLIMpro I2C device driver on APM X-Gene platform")
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
devm_clk_get_enabled() returns the clk already (prepared and) enabled
and the automatically called cleanup cares for disabling (and
unpreparing). So simplify .probe() and .remove() accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The controller will always generate a completion interrupt when the
transfer is finished normally or not. Currently we use either error or
completion interrupt to finish, this may result the completion
interrupt unhandled and corrupt the next transfer, especially at low
speed mode. Since on error case, the error interrupt will come first
then is the completion interrupt. So only use the completion interrupt
to finish the whole transfer process.
Fixes: d62fbdb99a85 ("i2c: add support for HiSilicon I2C controller")
Reported-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
After issuing all the messages we can disable the TX_EMPTY interrupts
to avoid handling redundant interrupts. For doing a sinlge bus
detection (i2cdetect -y -r 0) we can reduce ~97% interrupts (before
~12000 after ~400).
Signed-off-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver can be compile tested with !CONFIG_OF or !CONFIG_ACPI making
certain data unused:
drivers/i2c/busses/i2c-cros-ec-tunnel.c:295:34: error: ‘cros_ec_i2c_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/i2c/busses/i2c-owl.c:510:34: error: ‘owl_i2c_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/i2c/busses/i2c-mt65xx.c:514:34: error: ‘mtk_i2c_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
From the comment of platform_get_irq, it only returns non-zero IRQ
number and negative error number, other than zero.
Fix this by removing the if condition.
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
We found that after commit 9c46929e7989
("ARM: implement THREAD_INFO_IN_TASK for uniprocessor systems"), the
PCF85063 RTC driver stopped working on i.MX28 due to regmap_bulk_read()
reading bogus data into a stack buffer. This is caused by the i2c-mxs
driver using DMA transfers even for messages without the I2C_M_DMA_SAFE
flag, and the aforementioned commit enabling vmapped stacks.
As the MXS I2C controller requires DMA for reads of >4 bytes, DMA can't be
disabled, so the issue is fixed by using i2c_get_dma_safe_msg_buf() to
create a bounce buffer when needed.
Fixes: 9c46929e7989 ("ARM: implement THREAD_INFO_IN_TASK for uniprocessor systems")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When reading from I2C, the Tx watermark is set to 0. Unfortunately the
TDF (transmit data flag) is enabled when Tx FIFO entries is equal or less
than watermark. So it is set in every case, hence the reset default of 1.
This results in the MSR_RDF _and_ MSR_TDF flags to be set thus trying
to send Tx data on a read message.
Mask the IRQ status to filter for wanted flags only.
Fixes: a55fa9d0e42e ("i2c: imx-lpi2c: add low power i2c bus driver")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When start sending a new message clear the Rx & Tx buffer pointers in
order to avoid using stale pointers.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In the `cdns_i2c_mrecv()` function the CTRL register of the Cadence I2C
controller is written and read back multiple times. The register value does
not change on its own. So it is possible to remember the just written value
instead of reading it back from the hardware.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When selecting the clock dividers the Cadence I2C driver skips settings
where the resulting I2C bus frequency is larger than the requested
frequency.
If the resulting frequency is lower it will compute the error to actual
frequency. When calculating the difference it also handles the case where
the resulting frequency is larger.
Since the resulting frequency is always smaller or equal the computation of
the error can be simplified by only considering this case.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the Microchip FPGA
i2c drivers to use the new symbol.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The i2cdev_{at,de}tach_adapter() callbacks are used for two purposes:
1. As notifier callbacks, when (un)registering I2C adapters created or
destroyed after i2c_dev_init(),
2. As bus iterator callbacks, for registering already existing
adapters from i2c_dev_init(), and for cleanup.
Unfortunately both use cases expect different return values: the former
expects NOTIFY_* return codes, while the latter expects zero or error
codes, and aborts in case of error.
Hence in case 2, as soon as i2cdev_{at,de}tach_adapter() returns
(non-zero) NOTIFY_OK, the bus iterator aborts. This causes (a) only the
first already existing adapter to be registered, leading to missing
/dev/i2c-* entries, and (b) a failure to unregister all but the first
I2C adapter during cleanup.
Fix this by introducing separate callbacks for the bus iterator,
wrapping the notifier functions, and always returning succes.
Any errors inside these callback functions are unlikely to happen, and
are fatal anyway.
Fixes: cddf70d0bce71c2a ("i2c: dev: fix notifier return values")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Now that .probe() was changed not to get the id parameter, drivers can
be converted back to that with the eventual goal to drop .probe_new().
Implement that for the i2c drivers that are part of the i2c core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Now that .probe() was changed not to get the id parameter, drivers can
be converted back to that with the eventual goal to drop .probe_new().
Implement that for the i2c mux drivers.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back
type") introduced a new probe callback to convert i2c init routines to
not take an i2c_device_id parameter. Now that all in-tree drivers are
converted to the temporary .probe_new() callback, .probe() can be
modified to match the desired prototype.
Now that .probe() and .probe_new() have the same semantic, they can be
defined as members of an anonymous union to save some memory and
simplify the core code a bit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This is passing IS_ERR() instead of PTR_ERR() so instead of an error
code it prints and returns the number 1.
Fixes: 4a55ed6f89f5 ("i2c: Add GXP SoC I2C Controller")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
According to Documentation/i2c/fault-codes.rst, NACK after sending an
address should be -ENXIO.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
There used to be error messages which had to go. Now, it only consists
of 'break's, so it can go.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The ppc64le_allmodconfig sets I2C_PASEMI=y and leaves COMPILE_TEST to
default to y and I2C_APPLE to default to m, running into a known
incompatible configuration that breaks the build [1]. Specifically,
a common dependency (i2c-pasemi-core.o in this case) cannot be used by
both builtin and module consumers.
Disable I2C_APPLE when I2C_PASEMI is a builtin to prevent this.
[1]: https://lore.kernel.org/all/202112061809.XT99aPrf-lkp@intel.com
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- new drivers for HPE GXP and Loongson 2K/LS7A
- bigger refactorings for i801 and xiic
- gpio driver gained ACPI and SDA-write only support
- the core converted some OF helpers to fwnode helpers
- usual bunch of driver updates
* tag 'i2c-for-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
MAINTAINERS: Add HPE GXP I2C Support
i2c: Add GXP SoC I2C Controller
dt-bindings: i2c: Add hpe,gxp-i2c
i2c: xiic: Remove some dead code
i2c: xiic: Add SCL frequency configuration support
i2c: xiic: Update compatible with new IP version
dt-bindings: i2c: xiic: Add 'xlnx,axi-iic-2.1' to compatible
i2c: i801: Call i801_check_post() from i801_access()
i2c: i801: Call i801_check_pre() from i801_access()
i2c: i801: Centralize configuring block commands in i801_block_transaction
i2c: i801: Centralize configuring non-block commands in i801_simple_transaction
i2c: i801: Handle SMBAUXCTL_E32B in i801_block_transaction_by_block only
i2c: i801: Add i801_simple_transaction(), complementing i801_block_transaction()
Documentation: i2c: correct spelling
dt-bindings: i2c: i2c-st: convert to DT schema
i2c: i801: add helper i801_set_hstadd()
i2c: i801: make FEATURE_BLOCK_PROC dependent on FEATURE_BLOCK_BUFFER
i2c: i801: make FEATURE_HOST_NOTIFY dependent on FEATURE_IRQ
i2c: i801: improve interrupt handler
i2c: st: use pm_sleep_ptr to avoid ifdef CONFIG_PM_SLEEP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.3-rc1.
Nothing major in here, just lots of good development, including:
- Thunderbolt additions for new device support and features
- xhci driver updates and cleanups
- USB gadget media driver updates (includes media core changes that
were acked by the v4l2 maintainers)
- lots of other USB gadget driver updates for new features
- dwc3 driver updates and fixes
- minor debugfs leak fixes
- typec driver updates and additions
- dt-bindings conversions to yaml
- other small bugfixes and driver updates
All have been in linux-next for a while with no reported issues"
* tag 'usb-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (237 commits)
usb: dwc3: xilinx: Remove unused of_gpio,h
usb: typec: pd: Add higher capability sysfs for sink PDO
usb: typec: pd: Remove usb_suspend_supported sysfs from sink PDO
usb: dwc3: pci: add support for the Intel Meteor Lake-M
usb: gadget: u_ether: Don't warn in gether_setup_name_default()
usb: gadget: u_ether: Convert prints to device prints
usb: gadget: u_serial: Add null pointer check in gserial_resume
usb: gadget: uvc: fix missing mutex_unlock() if kstrtou8() fails
xhci: host: potential NULL dereference in xhci_generic_plat_probe()
dt-bindings: usb: amlogic,meson-g12a-usb-ctrl: make G12A usb3-phy0 optional
usb: host: fsl-mph-dr-of: reuse device_set_of_node_from_dev
of: device: Do not ignore error code in of_device_uevent_modalias
of: device: Ignore modalias of reused nodes
usb: gadget: configfs: Fix set but not used variable warning
usb: gadget: uvc: Use custom strings if available
usb: gadget: uvc: Allow linking function to string descs
usb: gadget: uvc: Pick up custom string descriptor IDs
usb: gadget: uvc: Allow linking XUs to string descriptors
usb: gadget: configfs: Attach arbitrary strings to cdev
usb: gadget: configfs: Support arbitrary string descriptors
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Change MFD support status from Supported to Maintained
New Drivers:
- Add support for the Intel Platform Management Component Interface
(PMCI)
Removed Drivers:
- HTC PASIC3 LED/DS1WM
- Toshiba T7L66XB, TC6387XB and TC6393XB TMIO
New Device Support:
- Add support for N6000 Flash to Intel M10 BMC PMCI
- Add support for Lenovo Yoga Tab 3 to Intel CHTWC PMIC
New Functionality:
- Provide Reset support to Syscon
Fix-ups:
- Explicitly provide missing include files
- Pass platform type data/info via the SPI/I2C/DT registration
strategy
- Lots of DT documentation / adaptions
- Replace scnprintf() with preferred sysfs_emit()
- Remove unused / superfluous code
- Fix some trivial whitesspace / spelling / grammatical issues
- Replace pm_power_off with new and improved
register_sys_off_handler() API
Bug Fixes:
- Reintroduce RK808-clkout registration - fixing Wi-Fi and Bluetooth
- Repair the order of AXPxxx IRQ PEK RISE/FALL definitions
- Refuse to build CS5535 on unsupported UML architectures
- Fix memory leaks in error return paths
- Prevent refcount leaks in error return paths"
* tag 'mfd-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (40 commits)
dt-bindings: mfd: qcom,tcsr: Add compatible for IPQ5332
dt-bindings: mfd: Add NXP BBNSM
mfd: ntxec: Add version number for EC in Tolino Vision
dt-bindings: mfd: syscon: Add mt8365-syscfg
mfd: Remove toshiba tmio drivers
mfd: arizona: Use pm_runtime_resume_and_get() to prevent refcnt leak
mfd: syscon: Allow reset control for syscon devices
dt-bindings: mfd/syscon: Add resets property
dt-bindings: mfd: syscon: Add amd,pensando-elba-syscon compatible
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8226
mfd: simple-mfd-i2c: Fix incoherent comment regarding DT registration
mfd: axp20x: Switch to the sys-off handler API
mfd: core: Spelling s/compement/complement/
mfd: max8925: Remove the unused function irq_to_max8925()
mfd: qcom-pm8xxx: Remove set but unused variable 'rev'
dt-bindings: mfd: syscon: Document GXP register compatible
mfd: twl4030-power: Drop empty platform remove function
mfd: twl: Fix TWL6032 phy vbus detection
mfd: pcf50633-adc: Fix potential memleak in pcf50633_adc_async_read()
MAINTAINERS: Move MFD from a Supported to Maintaied state
...
|
