| Age | Commit message (Collapse) | Author |
|---|
|
Remove the SMBus Quick operation from this driver because it is not
natively supported by the hardware and is wrongly implemented in the
driver.
The I2C controllers in Realtek RTL9300 and RTL9310 are SMBus-compliant
but there doesn't seem to be native support for the SMBus Quick
operation. It is not explicitly mentioned in the documentation but
looking at the registers which configure an SMBus transaction, one can
see that the data length cannot be set to 0. This suggests that the
hardware doesn't allow any SMBus message without data bytes (except for
those it does on it's own, see SMBus Block Read).
The current implementation of SMBus Quick operation passes a length of
0 (which is actually invalid). Before the fix of a bug in a previous
commit, this led to a read operation of 16 bytes from any register (the
one of a former transaction or any other value.
This caused issues like soft-bricked SFP modules after a simple probe
with i2cdetect which uses Quick by default. Running this with SFP
modules whose EEPROM isn't write-protected, some of the initial bytes
are overwritten because a 16-byte write operation is executed instead of
a Quick Write. (This temporarily soft-bricked one of my DAC cables.)
Because SMBus Quick operation is obviously not supported on these
controllers (because a length of 0 cannot be set, even when no register
address is set), remove that instead of claiming there is support. There
also shouldn't be any kind of emulated 'Quick' which just does another
kind of operation in the background. Otherwise, specific issues occur
in case of a 'Quick' Write which actually writes unknown data to an
unknown register.
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Cc: stable@vger.kernel.org # v6.13+
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Tested-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # On RTL9302C based board
Tested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250831100457.3114-4-jelonek.jonas@gmail.com
|
|
Add an explicit check for the xfer length to 'rtl9300_i2c_config_xfer'
to ensure the data length isn't within the supported range. In
particular a data length of 0 is not supported by the hardware and
causes unintended or destructive behaviour.
This limitation becomes obvious when looking at the register
documentation [1]. 4 bits are reserved for DATA_WIDTH and the value
of these 4 bits is used as N + 1, allowing a data length range of
1 <= len <= 16.
Affected by this is the SMBus Quick Operation which works with a data
length of 0. Passing 0 as the length causes an underflow of the value
due to:
(len - 1) & 0xf
and effectively specifying a transfer length of 16 via the registers.
This causes a 16-byte write operation instead of a Quick Write. For
example, on SFP modules without write-protected EEPROM this soft-bricks
them by overwriting some initial bytes.
For completeness, also add a quirk for the zero length.
[1] https://svanheule.net/realtek/longan/register/i2c_mst1_ctrl2
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Cc: stable@vger.kernel.org # v6.13+
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Tested-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # On RTL9302C based board
Tested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250831100457.3114-3-jelonek.jonas@gmail.com
|
|
Fix the current check for number of channels (child nodes in the device
tree). Before, this was:
if (device_get_child_node_count(dev) >= RTL9300_I2C_MUX_NCHAN)
RTL9300_I2C_MUX_NCHAN gives the maximum number of channels so checking
with '>=' isn't correct because it doesn't allow the last channel
number. Thus, fix it to:
if (device_get_child_node_count(dev) > RTL9300_I2C_MUX_NCHAN)
Issue occured on a TP-Link TL-ST1008F v2.0 device (8 SFP+ ports) and fix
is tested there.
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Cc: stable@vger.kernel.org # v6.13+
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Tested-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # On RTL9302C based board
Tested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250831100457.3114-2-jelonek.jonas@gmail.com
|
|
Hide the Intel Birch Stream SoC TCO WDT feature since it was removed.
On platforms with PCH TCO WDT, this redundant device might be rendering
errors like this:
[ 28.144542] sysfs: cannot create duplicate filename '/bus/platform/devices/iTCO_wdt'
Fixes: 8c56f9ef25a3 ("i2c: i801: Add support for Intel Birch Stream SoC")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220320
Signed-off-by: Chiasheng Lee <chiasheng.lee@linux.intel.com>
Cc: <stable@vger.kernel.org> # v6.7+
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250901125943.916522-1-chiasheng.lee@linux.intel.com
|
|
The expected on-wire format of an SMBus Block Write is
S Addr Wr [A] Comm [A] Count [A] Data [A] Data [A] ... [A] Data [A] P
Everything starting from the Count byte is provided by the I2C subsystem in
the array data->block. But the driver was skipping the Count byte
(data->block[0]) when sending it to the RTL93xx I2C controller.
Only the actual data could be seen on the wire:
S Addr Wr [A] Comm [A] Data [A] Data [A] ... [A] Data [A] P
This wire format is not SMBus Block Write compatible but matches the format
of an I2C Block Write. Simply adding the count byte to the buffer for the
I2C controller is enough to fix the transmission.
This also affects read because the I2C controller must receive the count
byte + $count * data bytes.
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: <stable@vger.kernel.org> # v6.13+
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-4-cd9dca0db722@narfation.org
|
|
The timeout for transfers was only set to 2ms. Because of this relatively
low limit, 12-byte read operations to the frontend MCU of a RTL8239 POE PSE
chip cluster was consistently resulting in a timeout.
The original OpenWrt downstream driver [1] was not using any timeout limit
at all. This is also possible by setting the timeout_us parameter of
regmap_read_poll_timeout() to 0. But since the driver currently implements
the ETIMEDOUT error, it is more sensible to increase the timeout in such a
way that communication with the (quite common) Realtek I2C-connected POE
management solution is possible.
[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=blob;f=target/linux/realtek/files-6.12/drivers/i2c/busses/i2c-rtl9300.c;h=c4d973195ef39dc56d6207e665d279745525fcac#l202
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: <stable@vger.kernel.org> # v6.13+
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-3-cd9dca0db722@narfation.org
|
|
The RTL93xx I2C controller has 4 32 bit registers to store the bytes for
the upcoming I2C transmission. The first byte is stored in the
least-significant byte of the first register. And the last byte in the most
significant byte of the last register. A map of the transferred bytes to
their order in the registers is:
reg 0: 0x04_03_02_01
reg 1: 0x08_07_06_05
reg 2: 0x0c_0b_0a_09
reg 3: 0x10_0f_0e_0d
The i2c_read() function basically demonstrates how the hardware would pick
up bytes from this register set. But the i2c_write() function was just
pushing bytes one after another to the least significant byte of a register
AFTER shifting the last one to the next more significant byte position.
If you would then have tried to send a buffer with numbers 1-11 using
i2c_write(), you would have ended up with following register content:
reg 0: 0x01_02_03_04
reg 1: 0x05_06_07_08
reg 2: 0x00_09_0a_0b
reg 3: 0x00_00_00_00
On the wire, you would then have seen:
Sr Addr Wr [A] 04 A 03 A 02 A 01 A 08 A 07 A 06 A 05 A 0b A 0a A 09 A P
But the correct data transmission was expected to be
Sr Addr Wr [A] 01 A 02 A 03 A 04 A 05 A 06 A 07 A 08 A 09 A 0a A 0b A P
Because of this multi-byte ordering problem, only single byte i2c_write()
operations were executed correctly (on the wire).
By shifting the byte directly to the correct end position in the register,
it is possible to avoid this incorrect byte ordering and fix multi-byte
transmissions.
The second initialization (to 0) of vals was also be dropped because this
array is initialized to 0 on the stack by using `= {};`. This makes the
fix a lot more readable.
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Cc: <stable@vger.kernel.org> # v6.13+
Co-developed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-2-cd9dca0db722@narfation.org
|
|
The data->block[0] variable comes from user. Without proper check,
the variable may be very large to cause an out-of-bounds bug.
Fix this bug by checking the value of data->block[0] first.
1. commit 39244cc75482 ("i2c: ismt: Fix an out-of-bounds bug in
ismt_access()")
2. commit 92fbb6d1296f ("i2c: xgene-slimpro: Fix out-of-bounds bug in
xgene_slimpro_i2c_xfer()")
Fixes: c366be720235 ("i2c: Add driver for the RTL9300 I2C controller")
Signed-off-by: Alex Guo <alexguo1023@gmail.com>
Cc: <stable@vger.kernel.org> # v6.13+
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250810-i2c-rtl9300-multi-byte-v5-1-cd9dca0db722@narfation.org
|
|
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
If an error occurs in the loop that creates the device adapters, then a
reference to 'dev' still needs to be released.
Use for_each_child_of_node_scoped() to both fix the issue and save one line
of code.
Fixes: d0f8e97866bf ("i2c: muxes: add support for tsd,mule-i2c multiplexer")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
This patch fixes an issue where the touchpad cursor movement becomes
slow on the Dell Precision 5560. Force the touchpad freq to 100khz
as a workaround.
Tested on Dell Precision 5560 with 6.14 to 6.14.6. Cursor movement
is now smooth and responsive.
Signed-off-by: fangzhong.zhou <myth5@myth5.com>
[wsa: kept sorting and removed unnecessary parts from commit msg]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
When the first driver for Apple Silicon was upstreamed we accidentally
included `default ARCH_APPLE` in its Kconfig which then spread to almost
every subsequent driver. As soon as ARCH_APPLE is set to y this will
pull in many drivers as built-ins which is not what we want.
Thus, drop `default ARCH_APPLE` from Kconfig.
Signed-off-by: Sven Peter <sven@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-mergewindow
i2c-host for v6.17, part 2
- apple: add support for Apple A7–A11, T2 chips
- qcom-geni: fix controller frequency mapping
- stm32f7: add DMA-safe transfer support
- tegra: use controller reset if device reset is missing
- tegra: remove unnecessary dma_sync*() calls
|
|
Pull drm updates from Dave Airlie:
"Highlights:
- Intel xe enable Panthor Lake, started adding WildCat Lake
- amdgpu has a bunch of reset improvments along with the usual IP
updates
- msm got VM_BIND support which is important for vulkan sparse memory
- more drm_panic users
- gpusvm common code to handle a bunch of core SVM work outside
drivers.
Detail summary:
Changes outside drm subdirectory:
- 'shrink_shmem_memory()' for better shmem/hibernate interaction
- Rust support infrastructure:
- make ETIMEDOUT available
- add size constants up to SZ_2G
- add DMA coherent allocation bindings
- mtd driver for Intel GPU non-volatile storage
- i2c designware quirk for Intel xe
core:
- atomic helpers: tune enable/disable sequences
- add task info to wedge API
- refactor EDID quirks
- connector: move HDR sink to drm_display_info
- fourcc: half-float and 32-bit float formats
- mode_config: pass format info to simplify
dma-buf:
- heaps: Give CMA heap a stable name
ci:
- add device tree validation and kunit
displayport:
- change AUX DPCD access probe address
- add quirk for DPCD probe
- add panel replay definitions
- backlight control helpers
fbdev:
- make CONFIG_FIRMWARE_EDID available on all arches
fence:
- fix UAF issues
format-helper:
- improve tests
gpusvm:
- introduce devmem only flag for allocation
- add timeslicing support to GPU SVM
ttm:
- improve eviction
sched:
- tracing improvements
- kunit improvements
- memory leak fixes
- reset handling improvements
color mgmt:
- add hardware gamma LUT handling helpers
bridge:
- add destroy hook
- switch to reference counted drm_bridge allocations
- tc358767: convert to devm_drm_bridge_alloc
- improve CEC handling
panel:
- switch to reference counter drm_panel allocations
- fwnode panel lookup
- Huiling hl055fhv028c support
- Raspberry Pi 7" 720x1280 support
- edp: KDC KD116N3730A05, N160JCE-ELL CMN, N116BCJ-EAK
- simple: AUO P238HAN01
- st7701: Winstar wf40eswaa6mnn0
- visionox: rm69299-shift
- Renesas R61307, Renesas R69328 support
- DJN HX83112B
hdmi:
- add CEC handling
- YUV420 output support
xe:
- WildCat Lake support
- Enable PanthorLake by default
- mark BMG as SRIOV capable
- update firmware recommendations
- Expose media OA units
- aux-bux support for non-volatile memory
- MTD intel-dg driver for non-volatile memory
- Expose fan control and voltage regulator in sysfs
- restructure migration for multi-device
- Restore GuC submit UAF fix
- make GEM shrinker drm managed
- SRIOV VF Post-migration recovery of GGTT nodes
- W/A additions/reworks
- Prefetch support for svm ranges
- Don't allocate managed BO for each policy change
- HWMON fixes for BMG
- Create LRC BO without VM
- PCI ID updates
- make SLPC debugfs files optional
- rework eviction rejection of bound external BOs
- consolidate PAT programming logic for pre/post Xe2
- init changes for flicker-free boot
- Enable GuC Dynamic Inhibit Context switch
i915:
- drm_panic support for i915/xe
- initial flip queue off by default for LNL/PNL
- Wildcat Lake Display support
- Support for DSC fractional link bpp
- Support for simultaneous Panel Replay and Adaptive sync
- Support for PTL+ double buffer LUT
- initial PIPEDMC event handling
- drm_panel_follower support
- DPLL interface renames
- allocate struct intel_display dynamically
- flip queue preperation
- abstract DRAM detection better
- avoid GuC scheduling stalls
- remove DG1 force probe requirement
- fix MEI interrupt handler on RT kernels
- use backlight control helpers for eDP
- more shared display code refactoring
amdgpu:
- add userq slot to INFO ioctl
- SR-IOV hibernation support
- Suspend improvements
- Backlight improvements
- Use scaling for non-native eDP modes
- cleaner shader updates for GC 9.x
- Remove fence slab
- SDMA fw checks for userq support
- RAS updates
- DMCUB updates
- DP tunneling fixes
- Display idle D3 support
- Per queue reset improvements
- initial smartmux support
amdkfd:
- enable KFD on loongarch
- mtype fix for ext coherent system memory
radeon:
- CS validation additional GL extensions
- drop console lock during suspend/resume
- bump driver version
msm:
- VM BIND support
- CI: infrastructure updates
- UBWC single source of truth
- decouple GPU and KMS support
- DP: rework I/O accessors
- DPU: SM8750 support
- DSI: SM8750 support
- GPU: X1-45 support and speedbin support for X1-85
- MDSS: SM8750 support
nova:
- register! macro improvements
- DMA object abstraction
- VBIOS parser + fwsec lookup
- sysmem flush page support
- falcon: generic falcon boot code and HAL
- FWSEC-FRTS: fb setup and load/execute
ivpu:
- Add Wildcat Lake support
- Add turbo flag
ast:
- improve hardware generations implementation
imx:
- IMX8qxq Display Controller support
lima:
- Rockchip RK3528 GPU support
nouveau:
- fence handling cleanup
panfrost:
- MT8370 support
- bo labeling
- 64-bit register access
qaic:
- add RAS support
rockchip:
- convert inno_hdmi to a bridge
rz-du:
- add RZ/V2H(P) support
- MIPI-DSI DCS support
sitronix:
- ST7567 support
sun4i:
- add H616 support
tidss:
- add TI AM62L support
- AM65x OLDI bridge support
bochs:
- drm panic support
vkms:
- YUV and R* format support
- use faux device
vmwgfx:
- fence improvements
hyperv:
- move out of simple
- add drm_panic support"
* tag 'drm-next-2025-07-30' of https://gitlab.freedesktop.org/drm/kernel: (1479 commits)
drm/tidss: oldi: convert to devm_drm_bridge_alloc() API
drm/tidss: encoder: convert to devm_drm_bridge_alloc()
drm/amdgpu: move reset support type checks into the caller
drm/amdgpu/sdma7: re-emit unprocessed state on ring reset
drm/amdgpu/sdma6: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5.2: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5: re-emit unprocessed state on ring reset
drm/amdgpu/gfx12: re-emit unprocessed state on ring reset
drm/amdgpu/gfx11: re-emit unprocessed state on ring reset
drm/amdgpu/gfx10: re-emit unprocessed state on ring reset
drm/amdgpu/gfx9.4.3: re-emit unprocessed state on kcq reset
drm/amdgpu/gfx9: re-emit unprocessed state on kcq reset
drm/amdgpu: Add WARN_ON to the resource clear function
drm/amd/pm: Use cached metrics data on SMUv13.0.6
drm/amd/pm: Use cached data for min/max clocks
gpu: nova-core: fix bounds check in PmuLookupTableEntry::new
drm/amdgpu: Replace HQD terminology with slots naming
drm/amdgpu: Add user queue instance count in HW IP info
drm/amd/amdgpu: Add helper functions for isp buffers
drm/amd/amdgpu: Initialize swnode for ISP MFD device
...
|
|
Update the I2C frequency table to match the recommended values
specified in the I2C hardware programming guide. In the current IPQ5424
configuration where 32MHz is the source clock, the I2C bus frequencies do
not meet expectations—for instance, 363KHz is achieved instead of the
expected 400KHz.
Fixes: 506bb2ab0075 ("i2c: qcom-geni: Support systems with 32MHz serial engine clock")
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Cc: <stable@vger.kernel.org> # v6.13+
Reviewed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250513-i2c-bus-freq-v1-1-9a333ad5757f@oss.qualcomm.com
|
|
Calling dma_sync_*() on a buffer from dma_alloc_coherent() is pointless.
The driver should not be doing its own bounce-buffering if the buffer is
allocated through dma_alloc_coherent().
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250710131206.2316-4-akhilrajeev@nvidia.com
|
|
For controllers that has an internal software reset, make the reset
property optional. This provides and option to use I2C in systems
that choose to restrict reset control from Linux or not to implement
the ACPI _RST method.
Internal reset was not required when the reset control was mandatory.
But on platforms where the resets are outside the control of Linux,
this had to be implemented by just returning success from BPMP or with
an empty _RST method in the ACPI table, basically ignoring the reset.
While the internal reset is not identical to the hard reset of the
controller, this will reset all the internal state of the controller
including FIFOs. This may slightly alter the behaviour in systems
which were ignoring the reset but it should not cause any functional
difference since all the required I2C registers are configured after
this reset, just as in boot. Considering that this sequence is hit
during the boot or during the I2C recovery path from an error, the
internal reset provides a better alternative than just ignoring the
reset.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250710131206.2316-3-akhilrajeev@nvidia.com
|
|
`i2c_*_dma_safe_msg_buf` APIs operate on a `struct i2c_msg`.
The get operation make sure the I2C buffer is DMA'able according to its
buffer length, or if the memory use is DMA coherent for example and
return a valid pointer for safe DMA access to be used.
The put operation release the pointer.
Prefer using generic API's than relying on private tests.
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250704-i2c-upstream-v4-3-84a095a2c728@foss.st.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core updates from Danilo Krummrich:
"debugfs:
- Remove unneeded debugfs_file_{get,put}() instances
- Remove last remnants of debugfs_real_fops()
- Allow storing non-const void * in struct debugfs_inode_info::aux
sysfs:
- Switch back to attribute_group::bin_attrs (treewide)
- Switch back to bin_attribute::read()/write() (treewide)
- Constify internal references to 'struct bin_attribute'
Support cache-ids for device-tree systems:
- Add arch hook arch_compact_of_hwid()
- Use arch_compact_of_hwid() to compact MPIDR values on arm64
Rust:
- Device:
- Introduce CoreInternal device context (for bus internal methods)
- Provide generic drvdata accessors for bus devices
- Provide Driver::unbind() callbacks
- Use the infrastructure above for auxiliary, PCI and platform
- Implement Device::as_bound()
- Rename Device::as_ref() to Device::from_raw() (treewide)
- Implement fwnode and device property abstractions
- Implement example usage in the Rust platform sample driver
- Devres:
- Remove the inner reference count (Arc) and use pin-init instead
- Replace Devres::new_foreign_owned() with devres::register()
- Require T to be Send in Devres<T>
- Initialize the data kept inside a Devres last
- Provide an accessor for the Devres associated Device
- Device ID:
- Add support for ACPI device IDs and driver match tables
- Split up generic device ID infrastructure
- Use generic device ID infrastructure in net::phy
- DMA:
- Implement the dma::Device trait
- Add DMA mask accessors to dma::Device
- Implement dma::Device for PCI and platform devices
- Use DMA masks from the DMA sample module
- I/O:
- Implement abstraction for resource regions (struct resource)
- Implement resource-based ioremap() abstractions
- Provide platform device accessors for I/O (remap) requests
- Misc:
- Support fallible PinInit types in Revocable
- Implement Wrapper<T> for Opaque<T>
- Merge pin-init blanket dependencies (for Devres)
Misc:
- Fix OF node leak in auxiliary_device_create()
- Use util macros in device property iterators
- Improve kobject sample code
- Add device_link_test() for testing device link flags
- Fix typo in Documentation/ABI/testing/sysfs-kernel-address_bits
- Hint to prefer container_of_const() over container_of()"
* tag 'driver-core-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core: (84 commits)
rust: io: fix broken intra-doc links to `platform::Device`
rust: io: fix broken intra-doc link to missing `flags` module
rust: io: mem: enable IoRequest doc-tests
rust: platform: add resource accessors
rust: io: mem: add a generic iomem abstraction
rust: io: add resource abstraction
rust: samples: dma: set DMA mask
rust: platform: implement the `dma::Device` trait
rust: pci: implement the `dma::Device` trait
rust: dma: add DMA addressing capabilities
rust: dma: implement `dma::Device` trait
rust: net::phy Change module_phy_driver macro to use module_device_table macro
rust: net::phy represent DeviceId as transparent wrapper over mdio_device_id
rust: device_id: split out index support into a separate trait
device: rust: rename Device::as_ref() to Device::from_raw()
arm64: cacheinfo: Provide helper to compress MPIDR value into u32
cacheinfo: Add arch hook to compress CPU h/w id into 32 bits for cache-id
cacheinfo: Set cache 'id' based on DT data
container_of: Document container_of() is not to be used in new code
driver core: auxiliary bus: fix OF node leak
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C Core:
- prevent double-free of an fwnode if it is a software node
- use recent helpers instead of custom ACPI or outdated OF ones
- add a more elaborate description of a message flag
Cleanups and refactorings:
- lpi2c, riic, st, stm32f7: general improvements
- riic: support more flexible IRQ configurations
- tegra: fix documentation
Improvements:
- lpi2c: improve register polling and add atomic transfer
- imx: use guarded spinlocks
New hardware support:
- Samsung Exynos 2200
- Renesas RZ/T2H (R9A09G077), RZ/N2H (R9A09G087)
DT binding:
- rk3x: enable power domains
- nxp: support clock property"
* tag 'i2c-for-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Fix double-free of fwnode in i2c_unregister_device()
i2c: lpi2c: implement xfer_atomic callback
i2c: lpi2c: use readl_poll_timeout() for register polling
dt-bindings: i2c: i2c-rk3x: Allow use of a power-domain
dt-bindings: i2c: exynos5: add samsung,exynos2200-hsi2c compatible
i2c: lpi2c: convert to use secs_to_jiffies()
i2c: st: Use min() to improve code
i2c: imx: use guard to take spinlock
i2c: stm32f7: Use str_on_off() helper
dt-bindings: i2c: nxp,pnx-i2c: allow clocks property
i2c: riic: Add support for RZ/T2H SoC
i2c: riic: Move generic compatible string to end of array
i2c: riic: Pass IRQ desc array as part of OF data
dt-bindings: i2c: renesas,riic: Document RZ/T2H and RZ/N2H support
dt-bindings: i2c: renesas,riic: Move ref for i2c-controller.yaml to the end
i2c: tegra: Add missing kernel-doc for dma_dev member
i2c: Clarify behavior of I2C_M_RD flag
i2c: mux: pca954x: Use dev_fwnode()
i2c: acpi: Replace custom code with device_match_acpi_handle()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"As is tradition, cpufreq is the part with the largest number of
updates that include core fixes and cleanups as well as updates of
several assorted drivers, but there are also quite a few updates
related to system sleep, mostly focused on asynchronous suspend and
resume of devices and on making the integration of system suspend
and resume with runtime PM easier.
Runtime PM is also updated to allow some code duplication in drivers
to be eliminated going forward and to work more consistently overall
in some cases.
Apart from that, there are some driver core updates related to PM
domains that should help to address ordering issues with devm_ cleanup
routines relying on PM domains, some assorted devfreq updates
including core fixes and cleanups, tooling updates, and documentation
and MAINTAINERS updates.
Specifics:
- Fix two initialization ordering issues in the cpufreq core and a
governor initialization error path in it, and clean it up (Lifeng
Zheng)
- Add Granite Rapids support in no-HWP mode to the intel_pstate
cpufreq driver (Li RongQing)
- Make intel_pstate always use HWP_DESIRED_PERF when operating in the
passive mode (Rafael Wysocki)
- Allow building the tegra124 cpufreq driver as a module (Aaron
Kling)
- Do minor cleanups for Rust cpufreq and cpumask APIs and fix
MAINTAINERS entry for cpu.rs (Abhinav Ananthu, Ritvik Gupta, Lukas
Bulwahn)
- Clean up assorted cpufreq drivers (Arnd Bergmann, Dan Carpenter,
Krzysztof Kozlowski, Sven Peter, Svyatoslav Ryhel, Lifeng Zheng)
- Add the NEED_UPDATE_LIMITS flag to the CPPC cpufreq driver
(Prashant Malani)
- Fix minimum performance state label error in the amd-pstate driver
documentation (Shouye Liu)
- Add the CPUFREQ_GOV_STRICT_TARGET flag to the userspace cpufreq
governor and explain HW coordination influence on it in the
documentation (Shashank Balaji)
- Fix opencoded for_each_cpu() in idle_state_valid() in the DT
cpuidle driver (Yury Norov)
- Remove info about non-existing QoS interfaces from the PM QoS
documentation (Ulf Hansson)
- Use c_* types via kernel prelude in Rust for OPP (Abhinav Ananthu)
- Add HiSilicon uncore frequency scaling driver to devfreq (Jie Zhan)
- Allow devfreq drivers to add custom sysfs ABIs (Jie Zhan)
- Simplify the sun8i-a33-mbus devfreq driver by using more devm
functions (Uwe Kleine-König)
- Fix an index typo in trans_stat() in devfreq (Chanwoo Choi)
- Check devfreq governor before using governor->name (Lifeng Zheng)
- Remove a redundant devfreq_get_freq_range() call from
devfreq_add_device() (Lifeng Zheng)
- Limit max_freq with scaling_min_freq in devfreq (Lifeng Zheng)
- Replace sscanf() with kstrtoul() in set_freq_store() (Lifeng Zheng)
- Extend the asynchronous suspend and resume of devices to handle
suppliers like parents and consumers like children (Rafael Wysocki)
- Make pm_runtime_force_resume() work for drivers that set the
DPM_FLAG_SMART_SUSPEND flag and allow PCI drivers and drivers that
collaborate with the general ACPI PM domain to set it (Rafael
Wysocki)
- Add kernel parameter to disable asynchronous suspend/resume of
devices (Tudor Ambarus)
- Drop redundant might_sleep() calls from some functions in the
device suspend/resume core code (Zhongqiu Han)
- Fix the handling of monitors connected right before waking up the
system from sleep (tuhaowen)
- Clean up MAINTAINERS entries for suspend and hibernation (Rafael
Wysocki)
- Fix error code path in the KEXEC_JUMP flow and drop a redundant
pm_restore_gfp_mask() call from it (Rafael Wysocki)
- Rearrange suspend/resume error handling in the core device suspend
and resume code (Rafael Wysocki)
- Fix up white space that does not follow coding style in the
hibernation core code (Darshan Rathod)
- Document return values of suspend-related API functions in the
runtime PM framework (Sakari Ailus)
- Mark last busy stamp in multiple autosuspend-related functions in
the runtime PM framework and update its documentation (Sakari
Ailus)
- Take active children into account in pm_runtime_get_if_in_use() for
consistency (Rafael Wysocki)
- Fix NULL pointer dereference in get_pd_power_uw() in the dtpm_cpu
power capping driver (Sivan Zohar-Kotzer)
- Add support for the Bartlett Lake platform to the Intel RAPL power
capping driver (Qiao Wei)
- Add PL4 support for Panther Lake to the intel_rapl_msr power
capping driver (Zhang Rui)
- Update contact information in the PM ABI docs and maintainer
information in the power domains DT binding (Rafael Wysocki)
- Update PM header inclusions to follow the IWYU (Include What You
Use) principle (Andy Shevchenko)
- Add flags to specify power on attach/detach for PM domains, make
the driver core detach PM domains in device_unbind_cleanup(), and
drop the dev_pm_domain_detach() call from the platform bus type
(Claudiu Beznea)
- Improve Python binding's Makefile for cpupower (John B. Wyatt IV)
- Fix printing of CORE, CPU fields in cpupower-monitor (Gautham
Shenoy)"
* tag 'pm-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits)
cpufreq: CPPC: Mark driver with NEED_UPDATE_LIMITS flag
PM: docs: Use my kernel.org address in ABI docs and DT bindings
PM: hibernate: Fix up white space that does not follow coding style
PM: sleep: Rearrange suspend/resume error handling in the core
Documentation: amd-pstate:fix minimum performance state label error
PM: runtime: Take active children into account in pm_runtime_get_if_in_use()
kexec_core: Drop redundant pm_restore_gfp_mask() call
kexec_core: Fix error code path in the KEXEC_JUMP flow
PM: sleep: Clean up MAINTAINERS entries for suspend and hibernation
drivers: cpufreq: add Tegra114 support
rust: cpumask: Replace `MaybeUninit` and `mem::zeroed` with `Opaque` APIs
cpufreq: Exit governor when failed to start old governor
cpufreq: Move the check of cpufreq_driver->get into cpufreq_verify_current_freq()
cpufreq: Init policy->rwsem before it may be possibly used
cpufreq: Initialize cpufreq-based frequency-invariance later
cpufreq: Remove duplicate check in __cpufreq_offline()
cpufreq: Contain scaling_cur_freq.attr in cpufreq_attrs
cpufreq: intel_pstate: Add Granite Rapids support in no-HWP mode
cpufreq: intel_pstate: Always use HWP_DESIRED_PERF in passive mode
PM / devfreq: Add HiSilicon uncore frequency scaling driver
...
|
|
Before commit df6d7277e552 ("i2c: core: Do not dereference fwnode in struct
device"), i2c_unregister_device() only called fwnode_handle_put() on
of_node-s in the form of calling of_node_put(client->dev.of_node).
But after this commit the i2c_client's fwnode now unconditionally gets
fwnode_handle_put() on it.
When the i2c_client has no primary (ACPI / OF) fwnode but it does have
a software fwnode, the software-node will be the primary node and
fwnode_handle_put() will put() it.
But for the software fwnode device_remove_software_node() will also put()
it leading to a double free:
[ 82.665598] ------------[ cut here ]------------
[ 82.665609] refcount_t: underflow; use-after-free.
[ 82.665808] WARNING: CPU: 3 PID: 1502 at lib/refcount.c:28 refcount_warn_saturate+0xba/0x11
...
[ 82.666830] RIP: 0010:refcount_warn_saturate+0xba/0x110
...
[ 82.666962] <TASK>
[ 82.666971] i2c_unregister_device+0x60/0x90
Fix this by not calling fwnode_handle_put() when the primary fwnode is
a software-node.
Fixes: df6d7277e552 ("i2c: core: Do not dereference fwnode in struct device")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hansg@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-mergewindow
i2c-host for v6.17, part 1
Cleanups and refactorings:
- lpi2c, riic, st, stm32f7: general improvements
- riic: support more flexible IRQ configurations
- tegra: fix documentation
Improvements:
- lpi2c: improve register polling and add atomic transfer
- imx: use guarded spinlocks
New hardware support:
- Samsung Exynos 2200
- Renesas RZ/T2H (R9A09G077), RZ/N2H (R9A09G087)
DT binding:
- rk3x: enable power domains
- nxp: support clock property
|
|
Rework the read and write code paths in the driver to support operation
in atomic contexts. To achieve this, the driver must not rely on IRQs
or perform any scheduling, e.g., via a sleep or schedule routine.
Implement atomic, sleep-free, and IRQ-less operation. This increases
complexity but is necessary for atomic I2C transfers required by some
hardware configurations, e.g., to trigger reboots on an external PMIC chip.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Carlos Song <carlos.song@nxp.com>
Tested-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250718133429.67219-3-francesco@dolcini.it
|
|
Replaces polling loops with the readl_poll_timeout() helper macro.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Carlos Song <carlos.song@nxp.com>
Tested-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250718133429.67219-2-francesco@dolcini.it
|
|
Since secs_to_jiffies() has been introduced in commit b35108a51cf7
("jiffies: Define secs_to_jiffies()"), we can use it to avoid scaling
the time to msec.
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250613110649.3283336-1-liyuesong@vivo.com
|
|
Use min() to reduce the code and improve its readability.
The type of the max parameter in the st_i2c_rd_fill_tx_fifo()
was changed from int to u32, because the max parameter passed
in is always greater than 0.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250709042347.550993-1-rongqianfeng@vivo.com
|
|
Original logic only sets the return value but doesn't jump out of the
loop if the bus is kept active by a client. This is not expected. A
malicious or buggy i2c client can hang the kernel in this case and
should be avoided. This is observed during a long time test with a
PCA953x GPIO extender.
Fix it by changing the logic to not only sets the return value, but also
jumps out of the loop and return to the caller with -ETIMEDOUT.
Fixes: fbfab1ab0658 ("i2c: qup: reorganization of driver code to remove polling for qup v1")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250616-qca-i2c-v1-1-2a8d37ee0a30@outlook.com
|
|
The current implementation uses wait_for_completion(), which can cause
the caller to hang indefinitely if the transfer never completes.
Switch to wait_for_completion_interruptible() so that the operation can
be interrupted by signals.
Fixes: 84e1d0bf1d71 ("i2c: virtio: disable timeout handling")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: <stable@vger.kernel.org> # v5.16+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/b8944e9cab8eb959d888ae80add6f2a686159ba2.1751541962.git.viresh.kumar@linaro.org
|
|
The acpi_evaluate_object() returns an ACPI error code and not
Linux one. For the some platforms the err will have positive code
which may be interpreted incorrectly. Use device_reset() for
reset control which handles it correctly.
Fixes: bd2fdedbf2ba ("i2c: tegra: Add the ACPI support")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Cc: <stable@vger.kernel.org> # v5.17+
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250710131206.2316-2-akhilrajeev@nvidia.com
|
|
Use guard to automatically release the lock after going out of scope
instead of calling it manually.
i2c_imx_slave_handle() can safely be entered with the lock held.
Refactored the i2c_imx_isr function so that i2c_imx_master_isr
does not participate in the guard scope
So Using scoped_guard simplifies the control flow
by ensuring consistent and automatic unlock,
which improves readability without affecting correctness.
Co-developed-by: Yongchao Jia <jyc0019@gmail.com>
Signed-off-by: Yongchao Jia <jyc0019@gmail.com>
Signed-off-by: Troy Mitchell <troymitchell988@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250531-i2c-imx-update-v4-1-bfad0c8fd45c@gmail.com
|
|
Remove hard-coded strings by using the str_on_off() helper.
Signed-off-by: Yumeng Fang <fang.yumeng@zte.com.cn>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250623203144007kQF7E1Bhy5PJl-Ph3u3Ou@zte.com.cn
|
|
Add support for the Renesas RZ/T2H (R9A09G077) SoC, which features a
different interrupt layout for the RIIC controller. Unlike other SoCs
with individual error interrupts, RZ/T2H uses a combined error interrupt
(EEI).
Introduce a new IRQ descriptor table for RZ/T2H, along with a custom
ISR (`riic_eei_isr`) to handle STOP and NACK detection from the shared
interrupt.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # on RZ/A1
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250625104526.101004-6-prabhakar.mahadev-lad.rj@bp.renesas.com
|
|
Reorder the entry in `riic_i2c_dt_ids` to place the generic compatible
string `renesas,riic-rz` at the end of the array, following the
convention used in other Renesas drivers.
Also, drop the unnecessary comma after the sentinel entry, as it is
not needed.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # on RZ/A1
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250625104526.101004-5-prabhakar.mahadev-lad.rj@bp.renesas.com
|
|
In preparation for adding support for Renesas RZ/T2H and RZ/N2H SoCs,
which feature a combined error interrupt instead of individual error
interrupts per condition, update the driver to support configurable IRQ
layouts via OF data.
Introduce a new `irqs` field and `num_irqs` count in `riic_of_data` to
allow future SoCs to provide a custom IRQ layout. This patch is a
non-functional change for existing SoCs and maintains compatibility with
the current `riic_irqs` array.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # on RZ/A1
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250625104526.101004-4-prabhakar.mahadev-lad.rj@bp.renesas.com
|
|
Fix the kernel-doc warning by describing the 'dma_dev' member in
the tegra_i2c_dev struct. This resolves the compilation warning:
drivers/i2c/busses/i2c-tegra.c:297: warning: Function parameter or struct member 'dma_dev' not described in 'tegra_i2c_dev'
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250522163814.399630-1-18255117159@163.com
|
|
Merge miscellaneous power management updates and cpupower utility
updates for 6.17-rc1:
- Update contact information in the PM ABI docs and maintainer
information in the power domains DT binding (Rafael Wysocki)
- Update PM header inclusions to follow the IWYU (Include What You Use)
principle (Andy Shevchenko)
- Add flags to specify power on attach/detach for PM domains, make the
driver core detach PM domains in device_unbind_cleanup(), and drop
the dev_pm_domain_detach() call from the platform bus type (Claudiu
Beznea)
- Improve Python binding's Makefile for cpupower (John B. Wyatt IV)
- Fix printing of CORE, CPU fields in cpupower-monitor (Gautham Shenoy)
* pm-misc:
PM: docs: Use my kernel.org address in ABI docs and DT bindings
driver core: platform: Drop dev_pm_domain_detach() call
PM: domains: Detach on device_unbind_cleanup()
PM: domains: Add flags to specify power on attach/detach
PM: Don't use "proxy" headers
* pm-tools:
cpupower: Improve Python binding's Makefile
pm: cpupower: Fix printing of CORE, CPU fields in cpupower-monitor
pm: cpupower: Fix the snapshot-order of tsc,mperf, clock in mperf_stop()
|
|
The regmap is coming from the parent also in case of Xe
GPUs. Reusing the Wangxun quirk for that.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Co-developed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250701122252.2590230-3-heikki.krogerus@linux.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo fixed the co-developed tags while merging]
|
|
The irq resource itself can be used as a generic way to
determine when polling is needed.
This not only removes the need for special additional device
properties that would soon be needed when the platform may
or may not have the irq, but it also removes the need to
check the platform in the first place in order to determine
is polling needed or not.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250701122252.2590230-2-heikki.krogerus@linux.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Before each I2C transfer using DMA, the I2C buffer is DMA'pped to make
sure the memory buffer is DMA'able. This is handle in the function
`stm32_i2c_prep_dma_xfer()`.
If the transfer fails for any reason the I2C buffer must be unmap.
Use the dma_callback to factorize the code and fix this issue.
Note that the `stm32f7_i2c_dma_callback()` is now called in case of DMA
transfer success and error and that the `complete()` on the dma_complete
completion structure is done inconditionnally in case of transfer
success or error as well as the `dmaengine_terminate_async()`.
This is allowed as a `complete()` in case transfer error has no effect
as well as a `dmaengine_terminate_async()` on a transfer success.
Also fix the unneeded cast and remove not more needed variables.
Fixes: 7ecc8cfde553 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Cc: <stable@vger.kernel.org> # v4.18+
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250704-i2c-upstream-v4-2-84a095a2c728@foss.st.com
|
|
If the DMA mapping failed, it produced an error log with the wrong
device name:
"stm32-dma3 40400000.dma-controller: rejecting DMA map of vmalloc memory"
Fix this issue by replacing the dev with the I2C dev.
Fixes: bb8822cbbc53 ("i2c: i2c-stm32: Add generic DMA API")
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Cc: <stable@vger.kernel.org> # v4.18+
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250704-i2c-upstream-v4-1-84a095a2c728@foss.st.com
|
|
If an error occurs after pm_runtime_use_autosuspend(), a corresponding
pm_runtime_dont_use_autosuspend() should be called.
In case of error in pm_runtime_resume_and_get(), it is not the case because
the error handling path is wrongly ordered.
Fix it.
Fixes: 780f62974125 ("i2c: omap: fix reference leak when pm_runtime_get_sync fails")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <stable@vger.kernel.org> # v5.13+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/af8a9b62996bebbaaa7c02986aa2a8325ef11596.1751701715.git.christophe.jaillet@wanadoo.fr
|
|
omap_i2c_init() can fail. Handle this error in omap_i2c_probe().
Fixes: 010d442c4a29 ("i2c: New bus driver for TI OMAP boards")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <stable@vger.kernel.org> # v2.6.19+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/565311abf9bafd7291ca82bcecb48c1fac1e727b.1751701715.git.christophe.jaillet@wanadoo.fr
|
|
Calling dev_pm_domain_attach()/dev_pm_domain_detach() in bus driver
probe/remove functions can affect system behavior when the drivers
attached to the bus use devres-managed resources. Since devres actions
may need to access device registers, calling dev_pm_domain_detach() too
early, i.e., before these actions complete, can cause failures on some
systems. One such example is Renesas RZ/G3S SoC-based platforms.
If the device clocks are managed via PM domains, invoking
dev_pm_domain_detach() in the bus driver's remove function removes the
device's clocks from the PM domain, preventing any subsequent
pm_runtime_resume*() calls from enabling those clocks.
The second argument of dev_pm_domain_attach() specifies whether the PM
domain should be powered on during attachment. Likewise, the second
argument of dev_pm_domain_detach() indicates whether the domain should be
powered off during detachment.
Upcoming changes address the issue described above (initially for the
platform bus only) by deferring the call to dev_pm_domain_detach() until
after devres_release_all() in device_unbind_cleanup(). The detach_power_off
field in struct dev_pm_info stores the detach power off info from the
second argument of dev_pm_domain_attach().
Because there are cases where the device's PM domain power-on/off behavior
must be conditional (e.g., in i2c_device_probe()), the patch introduces
PD_FLAG_ATTACH_POWER_ON and PD_FLAG_DETACH_POWER_OFF flags to be passed
to dev_pm_domain_attach().
Finally, dev_pm_domain_attach() and its users are updated to use the newly
introduced PD_FLAG_ATTACH_POWER_ON and PD_FLAG_DETACH_POWER_OFF macros.
This change is preparatory.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # I2C
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://patch.msgid.link/20250703112708.1621607-2-claudiu.beznea.uj@bp.renesas.com
[ rjw: Changelog adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- designware: initialise msg_write_idx during transfer
- microchip: check return value from core xfer call
- realtek: add 'reg' property constraint to the device tree
* tag 'i2c-for-6.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
dt-bindings: i2c: realtek,rtl9301: Fix missing 'reg' constraint
i2c: microchip-core: re-fix fake detections w/ i2cdetect
i2c/designware: Fix an initialization issue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers fixes from Ilpo Järvinen:
"Mostly a few lines fixed here and there except amd/isp4 which improves
swnodes relationships but that is a new driver not in any stable
kernels yet. The think-lmi driver changes also look relatively large
but there are just many fixes to it.
The i2c/piix4 change is a effectively a revert of the commit
7e173eb82ae9 ("i2c: piix4: Make CONFIG_I2C_PIIX4 dependent on
CONFIG_X86") but that required moving the header out from arch/x86
under include/linux/platform_data/
Summary:
- amd/isp4: Improve swnode graph (new driver exception)
- asus-nb-wmi: Use duo keyboard quirk for Zenbook Duo UX8406CA
- dell-lis3lv02d: Add Latitude 5500 accelerometer address
- dell-wmi-sysman: Fix WMI data block retrieval and class dev unreg
- hp-bioscfg: Fix class device unregistration
- i2c: piix4: Re-enable on non-x86 + move FCH header under platform_data/
- intel/hid: Wildcat Lake support
- mellanox:
- mlxbf-pmc: Fix duplicate event ID
- mlxbf-tmfifo: Fix vring_desc.len assignment
- mlxreg-lc: Fix bit-not-set logic check
- nvsw-sn2201: Fix bus number in error message & spelling errors
- portwell-ec: Move watchdog device under correct platform hierarchy
- think-lmi: Error handling fixes (sysfs, kset, kobject, class dev unreg)
- thinkpad_acpi: Handle HKEY 0x1402 event (2025 Thinkpads)
- wmi: Fix WMI event enablement"
* tag 'platform-drivers-x86-v6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (22 commits)
platform/x86: think-lmi: Fix sysfs group cleanup
platform/x86: think-lmi: Fix kobject cleanup
platform/x86: think-lmi: Create ksets consecutively
platform/mellanox: mlxreg-lc: Fix logic error in power state check
i2c: Re-enable piix4 driver on non-x86
Move FCH header to a location accessible by all archs
platform/x86/intel/hid: Add Wildcat Lake support
platform/x86: dell-wmi-sysman: Fix class device unregistration
platform/x86: think-lmi: Fix class device unregistration
platform/x86: hp-bioscfg: Fix class device unregistration
platform/x86: Update swnode graph for amd isp4
platform/x86: dell-wmi-sysman: Fix WMI data block retrieval in sysfs callbacks
platform/x86: wmi: Update documentation of WCxx/WExx ACPI methods
platform/x86: wmi: Fix WMI event enablement
platform/mellanox: nvsw-sn2201: Fix bus number in adapter error message
platform/mellanox: Fix spelling and comment clarity in Mellanox drivers
platform/mellanox: mlxbf-pmc: Fix duplicate event ID for CACHE_DATA1
platform/x86: thinkpad_acpi: handle HKEY 0x1402 event
platform/x86: asus-nb-wmi: add DMI quirk for ASUS Zenbook Duo UX8406CA
platform/x86: dell-lis3lv02d: Add Latitude 5500
...
|
|
Introducing support for smbus re-broke i2cdetect, causing it to detect
devices at every i2c address, just as it did prior to being fixed in
commit 49e1f0fd0d4cb ("i2c: microchip-core: fix "ghost" detections").
This was caused by an oversight, where the new smbus code failed to
check the return value of mchp_corei2c_xfer(). Check it, and propagate
any errors.
Fixes: d6ceb40538263 ("i2c: microchip-corei2c: add smbus support")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250630-shopper-proven-500f4075e7d6@spud
|
|
The i2c_dw_xfer_init() function requires msgs and msg_write_idx from the
dev context to be initialized.
amd_i2c_dw_xfer_quirk() inits msgs and msgs_num, but not msg_write_idx.
This could allow an out of bounds access (of msgs).
Initialize msg_write_idx before calling i2c_dw_xfer_init().
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 17631e8ca2d3 ("i2c: designware: Add driver support for AMD NAVI GPU")
Cc: <stable@vger.kernel.org> # v5.13+
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250627143511.489570-1-michael.j.ruhl@intel.com
|
|
loongarch and mips both support hardware that uses the i2c-piix4 driver.
It should not be restricted to x86, so drop the x86 dependency.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/all/CAMuHMdVPQLjOox5sMp34Z5MTwKv2WOpHa=MpZr8hWG22fQKcjw@mail.gmail.com/
Fixes: 7e173eb82ae97175 ("i2c: piix4: Make CONFIG_I2C_PIIX4 dependent on CONFIG_X86").
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250610205817.3912944-2-superm1@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
A new header fch.h was created to store registers used by different AMD
drivers. This header was included by i2c-piix4 in
commit 624b0d5696a8 ("i2c: piix4, x86/platform: Move the SB800 PIIX4 FCH
definitions to <asm/amd/fch.h>"). To prevent compile failures on non-x86
archs i2c-piix4 was set to only compile on x86 by commit 7e173eb82ae9717
("i2c: piix4: Make CONFIG_I2C_PIIX4 dependent on CONFIG_X86").
This was not a good decision because loongarch and mips both actually
support i2c-piix4 and set it enabled in the defconfig.
Move the header to a location accessible by all architectures.
Fixes: 624b0d5696a89 ("i2c: piix4, x86/platform: Move the SB800 PIIX4 FCH definitions to <asm/amd/fch.h>")
Suggested-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250610205817.3912944-1-superm1@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
