| Age | Commit message (Collapse) | Author |
|---|
|
Following are the major issues in current driver code
1. The current driver simply assumes the transfer completion
whenever its gets any non-error interrupts and then simply do the
polling of available/free bytes in FIFO.
2. The block mode is not working properly since no handling in
being done for OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_READ.
3. An i2c transfer can contain multiple message and QUP v2
supports reconfiguration during run in which the mode should be same
for all the sub transfer. Currently the mode is being programmed
before every sub transfer which is functionally wrong. If one message
is less than FIFO length and other message is greater than FIFO
length, then transfers will fail.
Because of above, i2c v2 transfers of size greater than 64 are failing
with following error message
i2c_qup 78b6000.i2c: timeout for fifo out full
To make block mode working properly and move to use the interrupts
instead of polling, major code reorganization is required. Following
are the major changes done in this patch
1. Remove the polling of TX FIFO free space and RX FIFO available
bytes and move to interrupts completely. QUP has QUP_MX_OUTPUT_DONE,
QUP_MX_INPUT_DONE, OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_REQ
interrupts to handle FIFO’s properly so check all these interrupts.
2. Determine the mode for transfer before starting by checking
all the tx/rx data length in each message. The complete message can be
transferred either in DMA mode or Programmed IO by FIFO/Block mode.
in DMA mode, both tx and rx uses same mode but in PIO mode, the TX and
RX can be in different mode.
3. During write, For FIFO mode, TX FIFO can be directly written
without checking for FIFO space. For block mode, the QUP will generate
OUT_BLOCK_WRITE_REQ interrupt whenever it has block size of available
space.
4. During read, both TX and RX FIFO will be used. TX will be used
for writing tags and RX will be used for receiving the data. In QUP,
TX and RX can operate in separate mode so configure modes accordingly.
5. For read FIFO mode, wait for QUP_MX_INPUT_DONE interrupt which
will be generated after all the bytes have been copied in RX FIFO. For
read Block mode, QUP will generate IN_BLOCK_READ_REQ interrupts
whenever it has block size of available data.
6. Split the transfer in chunk of one QUP block size(256 bytes)
and schedule each block separately. QUP v2 supports reconfiguration
during run in which QUP can transfer multiple blocks without issuing a
stop events.
7. Port the SMBus block read support for new code changes.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Following are the major issues in current driver code
1. The current driver simply assumes the transfer completion
whenever its gets any non-error interrupts and then simply do the
polling of available/free bytes in FIFO.
2. The block mode is not working properly since no handling in
being done for OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_REQ.
Because of above, i2c v1 transfers of size greater than 32 are failing
with following error message
i2c_qup 78b6000.i2c: timeout for fifo out full
To make block mode working properly and move to use the interrupts
instead of polling, major code reorganization is required. Following
are the major changes done in this patch
1. Remove the polling of TX FIFO free space and RX FIFO available
bytes and move to interrupts completely. QUP has QUP_MX_OUTPUT_DONE,
QUP_MX_INPUT_DONE, OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_REQ
interrupts to handle FIFO’s properly so check all these interrupts.
2. During write, For FIFO mode, TX FIFO can be directly written
without checking for FIFO space. For block mode, the QUP will generate
OUT_BLOCK_WRITE_REQ interrupt whenever it has block size of available
space.
3. During read, both TX and RX FIFO will be used. TX will be used
for writing tags and RX will be used for receiving the data. In QUP,
TX and RX can operate in separate mode so configure modes accordingly.
4. For read FIFO mode, wait for QUP_MX_INPUT_DONE interrupt which
will be generated after all the bytes have been copied in RX FIFO. For
read Block mode, QUP will generate IN_BLOCK_READ_REQ interrupts
whenever it has block size of available data.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
According to I2c specification, “If a master-receiver sends a
repeated START condition, it sends a not-acknowledge (A) just
before the repeated START condition”. QUP v2 supports sending
of NACK without stop with QUP_TAG_V2_DATARD_NACK so added the
same.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The BAM mode requires buffer for start tag data and tx, rx SG
list. Currently, this is being taken for maximum transfer length
(65K). But an I2C transfer can have multiple messages and each
message can be of this maximum length so the buffer overflow will
happen in this case. Since increasing buffer length won’t be
feasible since an I2C transfer can contain any number of messages
so this patch does following changes to make i2c transfers working
for multiple messages case.
1. Calculate the required buffers for 2 maximum length messages
(65K * 2).
2. Split the descriptor formation and descriptor scheduling.
The idea is to fit as many messages in one DMA transfers for 65K
threshold value (max_xfer_sg_len). Whenever the sg_cnt is
crossing this, then schedule the BAM transfer and subsequent
transfer will again start from zero.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Currently the completion timeout is being taken according to
maximum transfer length which is too high if SCL is operating in
high frequency. This patch calculates timeout on the basis of
one-byte transfer time and uses the same for completion timeout.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Currently each message length in complete transfer is being
checked for determining DMA mode and if any of the message length
is less than FIFO length then non DMA mode is being used which
will increase overhead. DMA can be used for any length and it
should be determined with complete transfer length. Now, this
patch selects DMA mode if the total length is greater than FIFO
length.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Currently the i2c error handling in BAM mode is not working
properly in stress condition.
1. After an error, the FIFO are being written with FLUSH and
EOT tags which should not be required since already these tags
have been written in BAM descriptor itself.
2. QUP state is being moved to RESET in IRQ handler in case
of error. When QUP HW encounters an error in BAM mode then it
moves the QUP STATE to PAUSE state. In this case, I2C_FLUSH
command needs to be executed while moving to RUN_STATE by writing
to the QUP_STATE register with the I2C_FLUSH bit set to 1.
3. In Error case, sometimes, QUP generates more than one
interrupt which will trigger the complete again. After an error,
the flush operation will be scheduled after doing
reinit_completion which should be triggered by BAM IRQ callback.
If the second QUP IRQ comes during this time then it will call
the complete and the transfer function will assume the all the
BAM HW descriptors have been completed.
4. The release DMA is being called after each error which
will free the DMA tx and rx channels. The error like NACK is very
common in I2C transfer and every time this will be overhead. Now,
since the error handling is proper so this release channel can be
completely avoided.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
In case of FLUSH operation, BAM copies INPUT EOT FLUSH (0x94)
instead of normal EOT (0x93) tag in input data stream when an
input EOT tag is received during flush operation. So only one tag
will be written instead of 2 separate tags.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The role of FLUSH and EOT tag is to flush already scheduled
descriptors in BAM HW in case of error. EOT is required only
when descriptors are scheduled in RX FIFO. If all the messages
are WRITE, then only FLUSH tag will be used.
A single BAM transfer can have multiple read and write messages.
The EOT and FLUSH tags should be scheduled at the end of BAM HW
descriptors. Since the READ and WRITE can be present in any order
so for some of the cases, these tags are not being written
correctly.
Following is one of the example
READ, READ, READ, READ
Currently EOT and FLUSH tags are being written after each READ.
If QUP gets NACK for first READ itself, then flush will be
triggered. It will look for first FLUSH tag in TX FIFO and will
stop there so only descriptors for first READ descriptors be
flushed. All the scheduled descriptors should be cleared to
generate BAM DMA completion.
Now this patch is scheduling FLUSH and EOT only once after all the
descriptors. So, flush will clear all the scheduled descriptors and
BAM will generate the completion interrupt.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The rx_nents and tx_nents are redundant. rx_buf and tx_buf can
be used for total number of SG entries. Since rx_buf and tx_buf
give the impression that it is buffer instead of count so rename
it to tx_cnt and rx_cnt for giving it more meaningful variable
name.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
1. Assigns use_dma in qup_dev structure itself which will
help in subsequent patches to determine the mode in IRQ handler.
2. Does minor code reorganization for loops to reduce the
unnecessary comparison and assignment.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The QUP BSLP BAM generates the following error sometimes if the
current I2C DMA transfer fails and the flush operation has been
scheduled
“bam-dma-engine 7884000.dma: Cannot free busy channel”
If any I2C error comes during BAM DMA transfer, then the QUP I2C
interrupt will be generated and the flush operation will be
carried out to make I2C consume all scheduled DMA transfer.
Currently, the same completion structure is being used for BAM
transfer which has already completed without reinit. It will make
flush operation wait_for_completion_timeout completed immediately
and will proceed for freeing the DMA resources where the
descriptors are still in process.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Acked-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The file has been updated from 2016 to 2018 so fixed the
copyright years.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
In case we receive NACK on DATA we shouldn't be resetting the controller,
rather we should issue STOP command. This will terminate the current
transaction and -EIO is returned.
While at that handle the SMBus Quick Command properly.
We shouldn't be setting the XLP9XX_I2C_CMD_READ/WRITE for such
transactions.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I2C bus enters the STOP condition after the DATA_DONE interrupt is raised.
Essentially the driver should be checking the bus state before sending
any transaction. In case a transaction is initiated while the
bus is busy, the prior transaction's stop condition is not achieved.
Add the check to make sure the bus is not busy before every transaction.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The hardware may not support SDA hold time configuration, but if it is
not set in the Device Tree either, there is no need to print a warning.
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The errata FE-8471889 description has been updated. There is still a
timing violation for repeated start. But the errata now states that it
was only the case for the Standard mode (100 kHz), in Fast mode (400 kHz)
there is no issue.
This patch limit the errata fix to the Standard mode.
It has been tesed successfully on the clearfog (Aramda 388 based board).
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Suspend functions seem to have been copied from i2c-cadence driver.
Rename the functions to match the rest of the driver.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
i2c/for-4.17
"These patches verify the device id of the PCA984x mux chips using
standardized (but rarely implemented) i2c device identification."
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag into asm-generic
Remove metag architecture
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
* tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
i2c: img-scb: Drop METAG dependency
media: img-ir: Drop METAG dependency
watchdog: imgpdc: Drop METAG dependency
MAINTAINERS/CREDITS: Drop METAG ARCHITECTURE
tty: Remove metag DA TTY and console driver
clocksource: Remove metag generic timer driver
irqchip: Remove metag irqchip drivers
Drop a bunch of metag references
docs: Remove remaining references to metag
docs: Remove metag docs
metag: Remove arch/metag/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Make sure to not disallow the chips on adapters that are not capable
of reading the device id, but also make sure to check the device id
before writing to the chip.
Tested-by: Adrian Fiergolski <adrian.fiergolski@cern.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
Can be used during probe to double check that the probed device is
what is expected.
Loosely based on code from Adrian Fiergolski <adrian.fiergolski@cern.ch>.
Tested-by: Adrian Fiergolski <adrian.fiergolski@cern.ch>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
Now that arch/metag/ has been removed, remove the METAG dependency from
the IMG SCB I2C device driver. The hardware is also present on MIPS SoCs
so the driver still has value.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-i2c@vger.kernel.org
Cc: linux-metag@vger.kernel.org
|
|
The buses should honor the firmware interface used to register the device,
but the I2C core reports a MODALIAS of the form i2c:<device> even for I2C
devices registered via OF.
This means that user-space will never get an OF stype uevent MODALIAS even
when the drivers modules contain aliases exported from both the I2C and OF
device ID tables. For example, an Atmel maXTouch Touchscreen registered by
a DT node with compatible "atmel,maxtouch" has the following module alias:
$ cat /sys/class/i2c-adapter/i2c-8/8-004b/modalias
i2c:maxtouch
So udev won't be able to auto-load a module for an OF-only device driver.
Many OF-only drivers duplicate the OF device ID table entries in an I2C ID
table only has a workaround for how the I2C core reports the module alias.
This patch changes the I2C core to report an OF related MODALIAS uevent if
the device was registered via OF. So for the previous example, after this
patch, the reported MODALIAS for the Atmel maXTouch will be the following:
$ cat /sys/class/i2c-adapter/i2c-8/8-004b/modalias
of:NtrackpadT<NULL>Catmel,maxtouch
NOTE: This patch may break out-of-tree drivers that were relying on this
behavior, and only had an I2C device ID table even when the device
was registered via OF. There are no remaining drivers in mainline
that do this, but out-of-tree drivers have to be fixed and define
a proper OF device ID table to have module auto-loading working.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Dmitry Mastykin <mastichi@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
ACPI_ERROR and ACPI_DEBUG_PRINT are not intended to be used by device
drivers. Use acpi_handle message logging functions instead.
As a nice side effect, it removes the following compiler warnings
which were printed when ACPI debug is disabled:
drivers/i2c/busses/i2c-scmi.c: In function "acpi_smbus_cmi_add_cap":
drivers/i2c/busses/i2c-scmi.c:328:39: warning: suggest braces around empty body in an "else" statement [-Wempty-body]
drivers/i2c/busses/i2c-scmi.c:338:12: warning: suggest braces around empty body in an "else" statement [-Wempty-body]
Suggested-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Accesses to SB800_PIIX4_SMB_IDX can occur from multiple drivers.
One example for another driver is the sp5100_tco driver.
Use request_muxed_region() to ensure synchronization.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The piix4 i2c driver is extremely slow. Replacing msleep()
with usleep_range() increases its speed substantially.
Use sleep ranges similar to those used in the i2c-801 driver
to keep things simple.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The error message:
[Fri Feb 16 13:42:13 2018] i2c-thunderx 0000:01:09.4: unhandled state: 0
is mis-leading as state 0 (bus error) is not an unknown state.
Return -EIO as before but avoid printing the message. Also rename
STAT_ERROR to STATE_BUS_ERROR.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use Kernel coding style for better readability.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Peter Rosin <peda@axentia.se>
|
|
The pointer reg is assigned a value that is never read, it is later
overwritten with a new value, hence the redundant initialization can
be removed.
Cleans up clang warning:
drivers/i2c/busses/i2c-stm32f4.c:352:16: warning: Value stored to 'reg'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
HSI2C_MASTER_ST_LOSE state is not documented properly, extensive tests
show that hardware is usually able to recover from this state without
interrupting the transfer. Moreover documentation says that
such state can be caused by slave clock stretching, and should not be
treated as an error during transaction. The only place it indicates
an error is just before starting transaction. In such case bus recovery
procedure should be performed - master should pulse SCL line nine times
and then send STOP condition, it can be repeated until SDA goes high.
The procedure can be performed using manual commands HSI2C_CMD_READ_DATA
and HSI2C_CMD_SEND_STOP.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
In case of transaction with I2C_M_RECV_LEN set, make sure the driver reads
the first byte and then updates the RX fifo with the expected length. Set
threshold to 1 byte so that driver gets an interrupt on receiving the first byte.
After which the transfer length is updated depending on the received length.
Also report SMBus block read functionality.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Fix the driver violation of the common practice to return
ENXIO error on a slave address NACK.
Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
of_get_property() is a bit cumbersome to use. Replace it with the newer
of_property_read_u32() for more readable code.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The very same check is done when calling i2c_new_device(). Remove it
here to avoid code duplication.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
'result' is mostly used in the kernel as int for functions returning
errno on failure. Here it is a pointer to the client struct, so let's
call it this way (as the parent function does, too).
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When debugging a ref counting problem, I overlooked this snipplet a few
times. Might be taste, but I think the new location is visually easier
recognizable.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If we cannot create a device, this is an error, not a warning. Fix the
log level.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
GPIO library can return -ENOSYS for the failed request.
Instead of failing ->probe() in this case override error code to 0.
Fixes: ca382f5b38f3 ("i2c: designware: add i2c gpio recovery option")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Fix spelling.
Signed-off-by: Patryk Kocielnik <patryk.kocielnik@gmail.com>
[wsa: fixed "Initialization", too]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We were leaving them in the power on state (or the state the firmware
had set up for some client, if we were taking over from them). The
boot state was 30 core clocks, when we actually want to sample some
time after (to make sure that the new input bit has actually arrived).
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Commits adding PCI IDs for Intel Braswell and Kaby Lake PCH-H lacked the
respective Kconfig and Documentation/i2c/busses/i2c-i801 change. Add
them now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
One I2C bus on my Atom E3845 board has been broken since 4.9.
It has two devices, both declared by ACPI and with built-in drivers.
There are two back-to-back transactions originating from the kernel, one
targeting each device. The first transaction works, the second one locks
up the I2C controller. The controller never recovers.
These kernel logs show up whenever an I2C transaction is attempted after
this failure.
i2c-designware-pci 0000:00:18.3: timeout in disabling adapter
i2c-designware-pci 0000:00:18.3: timeout waiting for bus ready
Waiting for the I2C controller status to indicate that it is enabled
before programming it fixes the issue.
I have tested this patch on 4.14 and 4.15.
Fixes: commit 2702ea7dbec5 ("i2c: designware: wait for disable/enable only if necessary")
Cc: linux-stable <stable@vger.kernel.org> #4.13+
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has the following changes for you:
- new flag to mark DMA safe buffers in i2c_msg. Also, some
infrastructure around it. And docs.
- huge refactoring of the at24 driver led by the new maintainer
Bartosz
- update I2C bus recovery to send STOP after recovery
- conversion from gpio to gpiod for I2C bus recovery
- adding a fault-injector to the i2c-gpio driver
- lots of small driver improvements, and bigger ones to
i2c-sh_mobile"
* 'i2c/for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (99 commits)
i2c: mv64xxx: Add myself as maintainer for this driver
i2c: mv64xxx: Fix clock resource by adding an optional bus clock
i2c: mv64xxx: Remove useless test before clk_disable_unprepare
i2c: mxs: use true and false for boolean values
i2c: meson: update doc description to fix build warnings
i2c: meson: add configurable divider factors
dt-bindings: i2c: update documentation for the Meson-AXG
i2c: imx-lpi2c: add runtime pm support
i2c: rcar: fix some trivial typos in comments
i2c: davinci: fix the cpufreq transition
i2c: rk3x: add proper kerneldoc header
i2c: rk3x: account for const type of of_device_id.data
i2c: acorn: remove outdated path from file header
i2c: acorn: add MODULE_LICENSE tag
i2c: rcar: implement bus recovery
i2c: send STOP after successful bus recovery
i2c: ensure SDA is released in recovery if SDA is controllable
i2c: add 'set_sda' to bus_recovery_info
i2c: add identifier in declarations for i2c_bus_recovery
i2c: make kerneldoc about bus recovery more precise
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are mostly minor bugfixes, cleanup and many defconfig updates to
support added drivers. In particular OMAP and PXA keep cleaning up the
legacy code base, as usual.
Nvidia adds some more SoC support code for Tegra 186.
For the first time on years, we are actually adding a non-DT platform
for the EP93xx based Liebherr controller BK3.1. It's a minor variation
of the EP93xx reference design and in active use, while EP93xx
apparently doesn't have enough new development to have any device tree
support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: omap: hwmod: fix section mismatch warnings
ARM: pxa/tosa-bt: add MODULE_LICENSE tag
arm64: defconfig: enable CONFIG_ACPI_APEI_EINJ
arm64: defconfig: enable EDAC GHES option
arm64: defconfig: enable CONFIG_ACPI_APEI_MEMORY_FAILURE
ARM: imx_v6_v7_defconfig: enable CONFIG_CPU_FREQ_STAT
Wind down ARM/TANGO port
ARM: davinci: constify gpio_led
ARM: davinci: drop unneeded newline
soc: Add SoC driver for Gemini
ARM: SAMSUNG: Add SPDX license identifiers
ARM: S5PV210: Add SPDX license identifiers
ARM: S3C64XX: Add SPDX license identifiers
ARM: S3C24XX: Add SPDX license identifiers
ARM: EXYNOS: Add SPDX license identifiers
ARM: imx: remove unused imx3 pm definitions
ARM: imx: don't abort MMDC probe if power saving status doesn't match
ARM: imx_v6_v7_defconfig: enable RTC_DRV_MXC_V2
ARM: imx_v6_v7_defconfig: Add missing config for DART-MX6 SoM
ARM: davinci: Use PTR_ERR_OR_ZERO()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This includes some infrastructure changes in the PM core, mostly
related to integration between runtime PM and system-wide suspend and
hibernation, plus some driver changes depending on them and fixes for
issues in that area which have become quite apparent recently.
Also included are changes making more x86-based systems use the Low
Power Sleep S0 _DSM interface by default, which turned out to be
necessary to handle power button wakeups from suspend-to-idle on
Surface Pro3.
On the cpufreq front we have fixes and cleanups in the core, some new
hardware support, driver updates and the removal of some unused code
from the CPU cooling thermal driver.
Apart from this, the Operating Performance Points (OPP) framework is
prepared to be used with power domains in the future and there is a
usual bunch of assorted fixes and cleanups.
Specifics:
- Define a PM driver flag allowing drivers to request that their
devices be left in suspend after system-wide transitions to the
working state if possible and add support for it to the PCI bus
type and the ACPI PM domain (Rafael Wysocki).
- Make the PM core carry out optimizations for devices with driver PM
flags set in some cases and make a few drivers set those flags
(Rafael Wysocki).
- Fix and clean up wrapper routines allowing runtime PM device
callbacks to be re-used for system-wide PM, change the generic
power domains (genpd) framework to stop using those routines
incorrectly and fix up a driver depending on that behavior of genpd
(Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
- Fix and clean up the PM core's device wakeup framework and
re-factor system-wide PM core code related to device wakeup
(Rafael Wysocki, Ulf Hansson, Brian Norris).
- Make more x86-based systems use the Low Power Sleep S0 _DSM
interface by default (to fix power button wakeup from
suspend-to-idle on Surface Pro3) and add a kernel command line
switch to tell it to ignore the system sleep blacklist in the ACPI
core (Rafael Wysocki).
- Fix a race condition related to cpufreq governor module removal and
clean up the governor management code in the cpufreq core (Rafael
Wysocki).
- Drop the unused generic code related to the handling of the static
power energy usage model in the CPU cooling thermal driver along
with the corresponding documentation (Viresh Kumar).
- Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh
Cheng).
- Add a new operating point to the imx6ul and imx6q cpufreq drivers
and switch the latter to using clk_bulk_get() (Anson Huang, Dong
Aisheng).
- Add support for multiple regulators to the TI cpufreq driver along
with a new DT binding related to that and clean up that driver
somewhat (Dave Gerlach).
- Fix a powernv cpufreq driver regression leading to incorrect CPU
frequency reporting, fix that driver to deal with non-continguous
P-states correctly and clean it up (Gautham Shenoy, Shilpasri
Bhat).
- Add support for frequency scaling on Armada 37xx SoCs through the
generic DT cpufreq driver (Gregory CLEMENT).
- Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
- Fix a transition delay setting regression in the longhaul cpufreq
driver (Viresh Kumar).
- Add Skylake X (server) support to the intel_pstate cpufreq driver
and clean up that driver somewhat (Srinivas Pandruvada).
- Clean up the cpufreq statistics collection code (Viresh Kumar).
- Drop cluster terminology and dependency on physical_package_id from
the PSCI driver and drop dependency on arm_big_little from the SCPI
cpufreq driver (Sudeep Holla).
- Add support for system-wide suspend and resume to the RAPL power
capping driver and drop a redundant semicolon from it (Zhen Han,
Luis de Bethencourt).
- Make SPI domain validation (in the SCSI SPI transport driver) and
system-wide suspend mutually exclusive as they rely on the same
underlying mechanism and cannot be carried out at the same time
(Bart Van Assche).
- Fix the computation of the amount of memory to preallocate in the
hibernation core and clean up one function in there (Rainer Fiebig,
Kyungsik Lee).
- Prepare the Operating Performance Points (OPP) framework for being
used with power domains and clean up one function in it (Viresh
Kumar, Wei Yongjun).
- Clean up the generic sysfs interface for device PM (Andy
Shevchenko).
- Fix several minor issues in power management frameworks and clean
them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
Sergey Senozhatsky, gaurav jindal).
- Make it easier to disable PM via Kconfig (Mark Brown).
- Clean up the cpupower and intel_pstate_tracer utilities (Doug
Smythies, Laura Abbott)"
* tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
PCI / PM: Remove spurious semicolon
cpufreq: scpi: remove arm_big_little dependency
drivers: psci: remove cluster terminology and dependency on physical_package_id
powercap: intel_rapl: Fix trailing semicolon
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / hibernate: Drop unused parameter of enough_swap
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / genpd: Stop/start devices without pm_runtime_force_suspend/resume()
cpufreq: powernv: Dont assume distinct pstate values for nominal and pmin
cpufreq: intel_pstate: Add Skylake servers support
cpufreq: intel_pstate: Replace bxt_funcs with core_funcs
platform/x86: surfacepro3: Support for wakeup from suspend-to-idle
ACPI / PM: Use Low Power S0 Idle on more systems
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / domains: Don't skip driver's ->suspend|resume_noirq() callbacks
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
powercap: add suspend and resume mechanism for SOC power limit
...
|
|
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add description for 'data' parameter and drop unused 'irq' memeber.
Here is the warnings:
drivers/i2c/busses/i2c-meson.c:103: warning: No description found for
parameter 'data'
drivers/i2c/busses/i2c-meson.c:103: warning: Excess struct member 'irq'
description in 'meson_i2c'
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
