| Age | Commit message (Collapse) | Author |
|---|
|
According to the datasheet the block process call requires block
buffer mode. The user may disable block buffer mode by module
parameter disable_features, in such a case we have to clear
FEATURE_BLOCK_PROC.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Host notification uses an interrupt, therefore it makes sense only if
interrupts are enabled. Make this dependency explicit by removing
FEATURE_HOST_NOTIFY if FEATURE_IRQ isn't set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Not sure if it can happen, but better play safe: If SMBHSTSTS_BYTE_DONE
and an error flag is set, then don't trust the result and skip calling
i801_isr_byte_done(). In addition clear status bit SMBHSTSTS_BYTE_DONE
in the main interrupt handler, this allows to simplify the code a
little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Rely on pm_sleep_ptr when setting the pm ops and get rid
of the ifdef CONFIG_PM_SLEEP around suspend/resume functions.
Signed-off-by: Alain Volmat <avolmat@me.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Move include/linux/qcom-geni-se.h to include/linux/soc/qcom/geni-se.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Link: https://lore.kernel.org/r/20230203210133.3552796-1-quic_eberman@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here, and this resolves a merge conflict with
the i915 driver as reported in linux-next
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On x86 devices with a CHT Whiskey Cove PMIC the driver for
the I2C bus coming from the PMIC is responsible for instantiating
the i2c_client for the charger chip.
Add the necessary i2c_board_info for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230126153823.22146-3-hdegoede@redhat.com
|
|
'DYNAMIC_MODE_READ_BROKEN_BIT' quirk added in the driver,
effected IP versions no longer enter dynamic mode.
So, remove local_irq_save/local_irq_restore APIs from driver.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
smbus_block_read is added to xiic driver to read from few sensors
which support this command. Since the number of bytes to read is not
known prior to transfer, xiic standard mode is being used for low level
control of IP.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If the tx_half_empty interrupt comes first instead of tx_empty,
STOP bit is generated even before all the bytes are transmitted
out on the bus.
STOP bit should be sent only after all the bytes in the FIFO are
transmitted out of the FIFO. So wait until FIFO is empty before sending
the STOP bit.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Xilinx I2C IP has two modes of operation, both of which implement
I2C transactions. The only difference from sw perspective is the
programming sequence for these modes.
Dynamic mode -> Simple to program, less number of steps in sequence.
Standard mode -> Gives flexibility, more number of steps in sequence.
In dynamic mode, during the i2c-read transactions, if there is a
delay(> 200us) between the register writes (address & byte count),
read transaction fails. On a system with load, this scenario is
occurring frequently.
To avoid this, switch to standard mode if there is a read request.
Added a quirk to identify the IP version effected by this and follow
the standard mode.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
repeated start
When a combined message request comes from user space, the
controller has to initiate repeated start sequence. In standard
mode, this repeated start sequence is corrupted if there is still
data in the Tx FIFO.
So, always make sure that all the bytes are completely transmitted
out of the FIFO by waiting for TXEMPTY, if the previous message is
of Tx type.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
read transfers
Added standard mode for AXI I2C controller to enable read transfers
of size more than 255 bytes. The driver selects standard mode in the
following scenarios.
1. If a single message request comes from user space, requesting a
read of more than 255 bytes
2. If a message set request comes from user space consisting of many
messages and if any one of them is a read operation, irrespective
of the size of transfer. (This is done because it is observed that
repeated start operation is not happening in dynamic mode read as
expected in a message set request from user space.)
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
net/core/gro.c
7d2c89b32587 ("skb: Do mix page pool and page referenced frags in GRO")
b1a78b9b9886 ("net: add support for ipv4 big tcp")
https://lore.kernel.org/all/20230203094454.5766f160@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This I2C module is integrated into the Loongson-2K SoCs and Loongson
LS7A bridge chip.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Now the Cypress CCG driver has been updated to support the
'firmware-name' property to align with device-tree, remove the
'ccgx,firmware-build' property as this is no longer needed.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20230131175748.256423-5-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Device-tree uses the 'firmware-name' string property to pass a name of
the firmware build to the Cypress CCGx driver. Add a new ACPI string
property to the NVIDIA GPU I2C driver to align with device-tree so that
we can migrate to using a common property name for both ACPI and
device-tree.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Co-developed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20230131175748.256423-3-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
regmap_read() API signature expects the caller to send "unsigned int"
type to return back the read value, but there are some occurrences of 'u32'
across i2c-designware-* files.
Change them to match the regmap_read() signature.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
On some AMD platforms, based on the new designware datasheet,
BIOS sets the BIT(11) within the IC_CON register to advertise
the "bus clear feature capability".
AMD/Designware datasheet says:
Bit(11) BUS_CLEAR_FEATURE_CTRL. Read-write,Volatile. Reset: 0.
Description: In Master mode:
- 1'b1: Bus Clear Feature is enabled.
- 1'b0: Bus Clear Feature is Disabled.
In Slave mode, this register bit is not applicable.
On AMD platform designs:
1. BIOS programs the BUS_CLEAR_FEATURE_CTRL and enables the detection
of SCL/SDA stuck low.
2. Whenever the stuck low is detected, the SMU FW shall do the bus
recovery procedure.
Currently, the way in which the "master_cfg" is built in the driver, it
overrides the BUS_CLEAR_FEATURE_CTRL advertised by BIOS and the SMU FW
cannot initiate the bus recovery if the stuck low is detected.
Hence add a check in i2c_dw_probe_master() that if the BIOS
advertises the bus clear feature, let driver not ignore it and
adapt accordingly.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are slave devices that understand I2C but have read-only SDA and
SCL. Examples are FD650 7-segment LED controller and its derivatives.
Typical board designs don't even have a pull-up for both pins.
Handle the new attributes for write-only SDA and missing pull-up on
SDA/SCL.
For either pin the open-drain and has-no-pullup properties are
mutually-exclusive, what is documented in the DT property documentation.
We don't add an extra warning here because the open-drain properties
are marked deprecated anyway.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
[wsa: switched to device properties]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This is in preparation of supporting write-only SDA in i2c-gpio.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Fix multiple W=1 kernel-doc warnings in i2c-rk3x.c:
drivers/i2c/busses/i2c-rk3x.c:83: warning: missing initial short description on line:
* struct i2c_spec_values:
drivers/i2c/busses/i2c-rk3x.c:139: warning: missing initial short description on line:
* struct rk3x_i2c_calced_timings:
drivers/i2c/busses/i2c-rk3x.c:162: warning: missing initial short description on line:
* struct rk3x_i2c_soc_data:
drivers/i2c/busses/i2c-rk3x.c:242: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Generate a START condition, which triggers a REG_INT_START interrupt.
drivers/i2c/busses/i2c-rk3x.c:261: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Generate a STOP condition, which triggers a REG_INT_STOP interrupt.
drivers/i2c/busses/i2c-rk3x.c:304: warning: expecting prototype for Setup a read according to i2c(). Prototype was for rk3x_i2c_prepare_read() instead
drivers/i2c/busses/i2c-rk3x.c:335: warning: expecting prototype for Fill the transmit buffer with data from i2c(). Prototype was for rk3x_i2c_fill_transmit_buf() instead
drivers/i2c/busses/i2c-rk3x.c:535: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Get timing values of I2C specification
drivers/i2c/busses/i2c-rk3x.c:552: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Calculate divider values for desired SCL frequency
drivers/i2c/busses/i2c-rk3x.c:713: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Calculate timing values for desired SCL frequency
drivers/i2c/busses/i2c-rk3x.c:963: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Setup I2C registers for an I2C operation specified by msgs, num.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add "struct" to prevent this kernel-doc warning:
drivers/i2c/busses/i2c-axxia.c:135: warning: cannot understand function prototype: 'struct axxia_i2c_dev '
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add support for the ACPI-based device registration, so that the driver
can be also enabled through ACPI table.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Tested-by: Peibao Liu <liupeibao@loongson.cn>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In the mrecv() function the Cadence I2C driver has the following expression
in an if clause.
((id->p_msg->flags & I2C_M_RECV_LEN) != I2C_M_RECV_LEN) &&
(id->recv_count <= CDNS_I2C_FIFO_DEPTH))
Earlier in the same function when I2C_M_RECV_LEN is set the recv_count is
initialized to a value that is larger than CDNS_I2C_FIFO_DEPTH. This means
if the first expression is false the second expression is also false.
Checking the first expression is thus redundant and can be removed.
This slightly simplifies the logic.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The irq field of the driver state struct is only used in the probe
function. There is no need to keep it around. Remove it from the state
struct and use a on-stack variable instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The CDNS_I2C_DATA_INTR_DEPTH is not used in the Cadence I2C driver. Remove
it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Currently the i2c subsystem rely on the controller device tree to
initialize the pinctrl recovery information, part of the drivers does
not set this field (rinfo->pinctrl), for example i2c DesignWare driver.
The pins information is saved part of the device structure before probe
and it's done on pinctrl_bind_pins().
Make the i2c init recovery to get the device pins if it's not
initialized by the driver from the device pins.
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
We have a set of return values that notifier callbacks can return. They
should not return 0, error codes or anything other than those predefined
values. Make the i2c character device's callback return NOTIFY_DONE or
NOTIFY_OK depending on the situation.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
|
|
Add fwnode APIs for finding and getting I2C adapters, which will be
used by the SFP code. These are passed the fwnode corresponding to
the adapter, and return the I2C adapter. It is the responsibility of
the caller to find the appropriate fwnode.
We keep the DT and ACPI interfaces, but where appropriate, recode them
to use the fwnode interfaces internally.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
All board support that was marked as 'unused' earlier can
now be removed, leaving the five machines that that still
had someone using them in 2022, or that are supported in
qemu.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This was marked as unused in 5.19 and can now be removed
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
During boot of I2SE Duckbill the kernel log contains a
confusing error:
Failed to request dma
This is caused by i2c-mxs tries to request a not yet available DMA
channel (-EPROBE_DEFER). So suppress this message by using
dev_err_probe().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add additional supported PCI IDs for latest AMD NAVI GPU card which
has an integrated Type-C controller and designware I2C with PCI
interface.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Tested-by: Sanath S <Sanath.S@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
i2c_master_hub is only used in i2c-qcom-geni.c now,
change it to static.
Fixes: cacd9643eca7 ("i2c: qcom-geni: add support for I2C Master Hub variant")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Ensure that i2c_mark_adapter_suspended() is always balanced by a call to
i2c_mark_adapter_resumed().
dw_i2c_plat_resume() must always be called, so that
i2c_mark_adapter_resumed() is called. This is not compatible with
DPM_FLAG_MAY_SKIP_RESUME, so remove the flag.
Since the controller is always resumed on system resume the
dw_i2c_plat_complete() callback is redundant and has been removed.
The unbalanced suspended flag was introduced by commit c57813b8b288
("i2c: designware: Lock the adapter while setting the suspended flag")
Before that commit, the system and runtime PM used the same functions. The
DPM_FLAG_MAY_SKIP_RESUME was used to skip the system resume if the driver
had been in runtime-suspend. If system resume was skipped, the suspended
flag would be cleared by the next runtime resume. The check of the
suspended flag was _after_ the call to pm_runtime_get_sync() in
i2c_dw_xfer(). So either a system resume or a runtime resume would clear
the flag before it was checked.
Having introduced the unbalanced suspended flag with that commit, a further
commit 80704a84a9f8
("i2c: designware: Use the i2c_mark_adapter_suspended/resumed() helpers")
changed from using a local suspended flag to using the
i2c_mark_adapter_suspended/resumed() functions. These use a flag that is
checked by I2C core code before issuing the transfer to the bus driver, so
there was no opportunity for the bus driver to runtime resume itself before
the flag check.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: c57813b8b288 ("i2c: designware: Lock the adapter while setting the suspended flag")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In functions i2c_dw_scl_lcnt() and i2c_dw_scl_hcnt() may have overflow
by depending on the values of the given parameters including the ic_clk.
For example in our use case where ic_clk is larger than one million,
multiplication of ic_clk * 4700 will result in 32 bit overflow.
Add cast of u64 to the calculation to avoid multiplication overflow, and
use the corresponding define for divide.
Fixes: 2373f6b9744d ("i2c-designware: split of i2c-designware.c into core and bus specific parts")
Signed-off-by: Lareine Khawaly <lareine@amazon.com>
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Make i2c_dw_clk_rate() to return u32 instead of unsigned long, as the
function return the value of get_clk_rate_khz() which returns u32.
Fixes: b33af11de236 ("i2c: designware: Do not require clock when SSCN and FFCN are provided")
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Many compatibles have been introduced, pointing to the same config data.
Leave a note reminding future developers to not do that again.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Core got a new helper 'i2c_client_get_device_id()', designware got
some bigger updates, the rest is driver updates all over the place"
* tag 'i2c-for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (41 commits)
i2c: ismt: Fix an out-of-bounds bug in ismt_access()
i2c: mux: reg: check return value after calling platform_get_resource()
i2c: xiic: Make sure to disable clock on .remove()
i2c: hisi: Add support to get clock frequency from clock
i2c: pxa-pci: fix missing pci_disable_device() on error in ce4100_i2c_probe
i2c: slave-eeprom: Convert to i2c's .probe_new()
i2c: mux: pca954x: Convert to i2c's .probe_new()
drivers/i2c: use simple i2c probe
i2c: mux: pca9541: switch to using .probe_new
i2c: gpio: Fix potential unused warning for 'i2c_gpio_dt_ids'
i2c: qcom-geni: add support for I2C Master Hub variant
i2c: qcom-geni: add desc struct to prepare support for I2C Master Hub variant
soc: qcom: geni-se: add support for I2C Master Hub wrapper variant
soc: qcom: geni-se: add desc struct to specify clocks from device match data
dt-bindings: i2c: qcom-geni: document I2C Master Hub serial I2C engine
dt-bindings: qcom: geni-se: document I2C Master Hub wrapper variant
dt-bindings: i2c: renesas,riic: Document RZ/Five SoC
i2c: tegra: Set ACPI node as primary fwnode
i2c: smbus: add DDR support for SPD
i2c: /pasemi: PASemi I2C controller IRQ enablement
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This looks like a relatively calm development cycle; there have been
only few changes in ALSA and ASoC core sides while we get lots of
device-specific fixes and updates as usual. Most of commits are about
ASoC, including Intel SOF/AVS and many device tree updates.
Below are some highlights:
Core:
- Improvement in memalloc helper for fallback allocations
- More cleanups of ASoC DAPM code
ASoC:
- Factoring out of mapping hw_params onto SoundWire configuration
- The ever ongoing overhauls of the Intel DSP code continue,
including support for loading libraries and probes with IPC4 on
SOF.
- Support for more sample formats on JZ4740
- Lots of device tree conversions and fixups
- Support for Allwinner D1, a range of AMD and Intel systems,
Mediatek systems with multiple DMICs, Nuvoton NAU8318, NXP
fsl_rpmsg and i.MX93, Qualcomm AudioReach Enable, MFC and SAL,
RealTek RT1318 and Rockchip RK3588
ALSA:
- Addition of PCM kselftest; still minimalistic but can be extended
in future
- Fixes for corner-case XRUNs with USB-audio implicit feedback mode
- Usual device-specific quirk updates for USB- and HD-audio
- FireWire DICE updates
This also contains a few cross-tree updates:
- Some OMAP board file updates for removal of relevant OMAP platforms
- A new I2C API update for I2C probe API adaption
- A DRM update for the further hdmi-codec updates"
* tag 'sound-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (417 commits)
ALSA: mts64: fix possible null-ptr-defer in snd_mts64_interrupt
ALSA: patch_realtek: Fix Dell Inspiron Plus 16
ALSA: hda/cirrus: Add extra 10 ms delay to allow PLL settle and lock.
ASoC: dt-bindings: Correct Alexandre Belloni email
ASoC: dt-bindings: maxim,max98504: Convert to DT schema
ASoC: dt-bindings: maxim,max98357a: Convert to DT schema
ASoC: dt-bindings: Reference common DAI properties
ASoC: dt-bindings: Extend name-prefix.yaml into common DAI properties
ASoC: rt715: Make read-only arrays capture_reg_H and capture_reg_L static const
ASoC: uniphier: aio-core: Make some read-only arrays static const
ASoC: wcd938x: Make read-only array minCode_param static const
ASoC: qcom: lpass-sc7280: Add maybe_unused tag for system PM ops
ASoC : SOF: amd: Add support for IPC and DSP dumps
ASoC: SOF: amd: Use poll function instead to read ACP_SHA_DSP_FW_QUALIFIER
ALSA: usb-audio: Workaround for XRUN at prepare
ALSA: pcm: Handle XRUN at trigger START
ALSA: pcm: Set missing stop_operating flag at undoing trigger start
drm: tda99x: Don't advertise non-existent capture support
ASoC: hdmi-codec: Allow playback and capture to be disabled
kselftest/alsa: Add more coverage of sample rates and channel counts
...
|
|
When the driver does not check the data from the user, the variable
'data->block[0]' may be very large to cause an out-of-bounds bug.
The following log can reveal it:
[ 33.995542] i2c i2c-1: ioctl, cmd=0x720, arg=0x7ffcb3dc3a20
[ 33.995978] ismt_smbus 0000:00:05.0: I2C_SMBUS_BLOCK_DATA: WRITE
[ 33.996475] ==================================================================
[ 33.996995] BUG: KASAN: out-of-bounds in ismt_access.cold+0x374/0x214b
[ 33.997473] Read of size 18446744073709551615 at addr ffff88810efcfdb1 by task ismt_poc/485
[ 33.999450] Call Trace:
[ 34.001849] memcpy+0x20/0x60
[ 34.002077] ismt_access.cold+0x374/0x214b
[ 34.003382] __i2c_smbus_xfer+0x44f/0xfb0
[ 34.004007] i2c_smbus_xfer+0x10a/0x390
[ 34.004291] i2cdev_ioctl_smbus+0x2c8/0x710
[ 34.005196] i2cdev_ioctl+0x5ec/0x74c
Fix this bug by checking the size of 'data->block[0]' first.
Fixes: 13f35ac14cd0 ("i2c: Adding support for Intel iSMT SMBus 2.0 host controller")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
It will cause null-ptr-deref in resource_size(), if platform_get_resource()
returns NULL, move calling resource_size() after devm_ioremap_resource() that
will check 'res' to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: b3fdd32799d8 ("i2c: mux: Add register-based mux i2c-mux-reg")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
