| Age | Commit message (Collapse) | Author |
|---|
|
The patch adds PIO asynchronous wakeup support while PIO PCIe Endpoint
function is in D3 state. When such a wakeup event occurs, the PIO
asserts a PIO_WAKE signal, which in turn triggers PCIe Wake signaling.
This wake request should trigger the PCIe Host to take the PIO PCIe
Endpoint function into the D0 device state.
The device supports up to 96 PIOs distributed across three GPIO banks.
During suspend and resume, the driver checks the status of each GPIO bank
to determine if any GPIOs with wake masking enabled have triggered an
event. Upon resume, PIOxx_STATUS register must be cleared by software
explicitly to enable the detection of the next transition.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20250513091557.3660-3-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
later devices
Systems that issue PCIe hot reset requests during a suspend/resume
cycle cause PCI1XXXX device revisions prior to C0 to get its GPIO
configuration registers reset to hardware default values. This results
in device inaccessibility and GPIO read/write failure. Starting with
Revision C0, support was added in the device hardware (via the Hot
Reset Disable Bit) to allow resetting only the PCIe interface and its
associated logic, but preserving the GPIO configurations during a hot
reset. This patch enables the hot reset disable feature during suspend/
resume for C0 and later revisions of the device.
mchp_pci1xxxx_gpio is an auxiliary child of mchp_pci1xxxx_gp and does
not have access to system register address space for reading the device
revision. Hence, the device revision is retrieved directly from PCIe
config space.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20250513091557.3660-2-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the char-misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Under irq_ack, pci1xxxx_assign_bit reads the current interrupt status,
modifies and writes the entire value back. Since, the IRQ status bit
gets cleared on writing back, the better approach is to directly write
the bitmask to the register in order to preserve the value.
Fixes: 1f4d8ae231f4 ("misc: microchip: pci1xxxx: Add gpio irq handler and irq helper functions irq_ack, irq_mask, irq_unmask and irq_set_type of irq_chip.")
Cc: stable <stable@kernel.org>
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20250313170856.20868-3-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolve kernel panic while accessing IRQ handler associated with the
generated IRQ. This is done by acquiring the spinlock and storing the
current interrupt state before handling the interrupt request using
generic_handle_irq.
A previous fix patch was submitted where 'generic_handle_irq' was
replaced with 'handle_nested_irq'. However, this change also causes
the kernel panic where after determining which GPIO triggered the
interrupt and attempting to call handle_nested_irq with the mapped
IRQ number, leads to a failure in locating the registered handler.
Fixes: 194f9f94a516 ("misc: microchip: pci1xxxx: Resolve kernel panic during GPIO IRQ handling")
Cc: stable <stable@kernel.org>
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20250313170856.20868-2-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250408-gpiochip-set-rv-misc-v1-1-eb6345aea5cd@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the IIO fixes in here as well, and it resolves a merge conflict
in:
drivers/iio/adc/ti-ads1119.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Driver returns -EOPNOTSUPPORTED on unsupported parameters case in set
config. Upper level driver checks for -ENOTSUPP. Because of the return
code mismatch, the ioctls from userspace fail. Resolve the issue by
passing -ENOTSUPP during unsupported case.
Fixes: 7d3e4d807df2 ("misc: microchip: pci1xxxx: load gpio driver for the gpio controller auxiliary device enumerated by the auxiliary bus driver.")
Cc: stable <stable@kernel.org>
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20241205133626.1483499-3-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolve kernel panic caused by improper handling of IRQs while
accessing GPIO values. This is done by replacing generic_handle_irq with
handle_nested_irq.
Fixes: 1f4d8ae231f4 ("misc: microchip: pci1xxxx: Add gpio irq handler and irq helper functions irq_ack, irq_mask, irq_unmask and irq_set_type of irq_chip.")
Cc: stable <stable@kernel.org>
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20241205133626.1483499-2-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support to configure GPIO pins for push-pull drive mode.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20241205134956.1493091-1-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: linux-gpio@vger.kernel.org
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230223133252.2257276-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SIMPLE_DEV_PM_OPS() in pci1xxxx's gpio driver
build errors listed below and reported by Sudip Mukherjee
<sudipm.mukherjee@gmail.com> for the builds of
riscv, s390, csky, alpha and loongarch allmodconfig are fixed in
this patch.
drivers/misc/mchp_pci1xxxx/mchp_pci1xxxx_gpio.c:311:12: error: 'pci1xxxx_gpio_resume' defined but not used [-Werror=unused-function]
311 | static int pci1xxxx_gpio_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~
drivers/misc/mchp_pci1xxxx/mchp_pci1xxxx_gpio.c:295:12: error: 'pci1xxxx_gpio_suspend' defined but not used [-Werror=unused-function]
295 | static int pci1xxxx_gpio_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~
Fixes: 4ec7ac90ff39 ("misc: microchip: pci1xxxx: Add power management functions - suspend & resume handlers.")
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20220915094729.646185-1-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove duplicate include in mchp_pci1xxxx_gpio.c
Fixes: 7d3e4d807df2 ("misc: microchip: pci1xxxx: load gpio driver for the gpio controller auxiliary device enumerated by the auxiliary bus driver.")
Reviewed-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Link: https://lore.kernel.org/r/20220913030257.22352-1-hanyihao@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the module_auxiliary_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Fixes: 7d3e4d807df2 ("misc: microchip: pci1xxxx: load gpio driver for the gpio controller auxiliary device enumerated by the auxiliary bus driver.")
Reviewed-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20220907145808.1789249-5-weiyongjun@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Fixes: 7d3e4d807df2 ("misc: microchip: pci1xxxx: load gpio driver for the gpio controller auxiliary device enumerated by the auxiliary bus driver.")
Reviewed-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20220907145808.1789249-4-weiyongjun@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sparse tool complains as follows:
drivers/misc/mchp_pci1xxxx/mchp_pci1xxxx_gpio.c:409:34: warning:
symbol 'pci1xxxx_gpio_auxiliary_id_table' was not declared. Should it be static?
This symbol is not used outside of mchp_pci1xxxx_gpio.c, so marks it static.
Fixes: 7d3e4d807df2 ("misc: microchip: pci1xxxx: load gpio driver for the gpio controller auxiliary device enumerated by the auxiliary bus driver.")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20220907145808.1789249-3-weiyongjun@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver allocates the spinlock but not initialize it.
Use spin_lock_init() on it to initialize it correctly.
Fixes: 7d3e4d807df2 ("misc: microchip: pci1xxxx: load gpio driver for the gpio controller auxiliary device enumerated by the auxiliary bus driver.")
Reviewed-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20220907145808.1789249-2-weiyongjun@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
handlers.
Power event handlers suspend and resume are invoked by the operating
system to notify the driver about the power events. Wakeup is enabled
before entering suspend and disabled after resuming.
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20220824200047.150308-6-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
irq_ack, irq_mask, irq_unmask and irq_set_type of irq_chip.
The helper functions irq_set_type, irq_mask, irq_unmask and
irq_ack configure the interrupt type, mask, unmask and
acknowledge the interrupts.
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20220824200047.150308-5-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
output, get status, handle I/O for gpio pins.
direction_input and direction_output functions configures a gpio pin as
input and output respectively. get_direction function returns if a gpio
pin is output or input. get function returns the value of a gpio pin
whereas set function assigns output value for a gpio pin.
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20220824200047.150308-4-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
auxiliary device enumerated by the auxiliary bus driver.
PIO function's auxiliary bus driver enumerates separate child devices for
GPIO controller and OTP/EEPROM interface. This gpio driver implemented
based on the gpio framework is loaded for the gpio auxiliary device.
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20220824200047.150308-3-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
