| Age | Commit message (Collapse) | Author |
|---|
|
Add a new quirk flag PCI_DEV_FLAGS_BRIDGE_XLATE_ROOT to limit the DMA alias
search to go no further than the bridge where the IOMMU unit is attached.
The flag will be used to indicate a bridge device which forwards the
address translation requests to the IOMMU, i.e., where the interrupt and
DMA requests leave the PCIe hierarchy and go into the system blocks.
Usually this happens at the PCI RC, so this flag is not needed. But on
systems where there are bridges that introduce aliases above the IOMMU,
this flag prevents pci_for_each_dma_alias() from generating aliases that
the IOMMU will never see.
The function pci_for_each_dma_alias() is updated to stop when it see a
bridge with this flag set.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195447
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: David Daney <david.daney@cavium.com>
|
|
In the PCI_MMAP_PROCFS case when the address being passed by the user is a
'user visible' resource address based on the bus window, and not the actual
contents of the resource, that's what we need to be checking it against.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
|
|
The ITE 8893 bridge has the same problems as the ITE 8892, which were
resulting in crippling an older PCI 1Gbps NIC down to 45Mbps throughput
with IOMMU and VT-d enabled. With the patch, this old e1000 goes back up
to ~900Mbps.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Add a couple of special IOCTLs to:
* Inform userspace of firmware partition locations
* Pass event counts and allow userspace to wait on events
* Translate PFF numbers used by the switch to port numbers
[Dan Carpenter <dan.carpenter@oracle.com>: fix off-by-one in
ioctl_event_ctl()]
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Stephen Bates <stephen.bates@microsemi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wei Zhang <wzhang@fb.com>
Reviewed-by: Jens Axboe <axboe@fb.com>
|
|
Add a few read-only sysfs attributes which provide some device information
that is exposed from the devices, primarily component and device names and
versions.
These are documented in Documentation/ABI/testing/sysfs-class-switchtec.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Stephen Bates <stephen.bates@microsemi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wei Zhang <wzhang@fb.com>
Reviewed-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "hisilicon,pcie-almost-ecam" binding goes against the usual DT
conventions, and is non-sensical in that it describes the IP based on
what it isn't. Fix the DT binding with "hisilicon,hip06-pcie-ecam"
and "hisilicon,hip07-pcie-ecam".
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
All platforms using Rockchip use a common clock for the Root Port and the
slot connected to it. Indicate this by setting the Slot Clock Configuration
(PCI_EXP_LNKSTA_SLC) bit in the Root Port's Link Status.
Per the Implementation Note in the spec (PCIe r3.1, sec 7.8.7), if the
downstream component also sets PCI_EXP_LNKSTA_SLC, software may set the
Common Clock Configuration (PCI_EXP_LNKCTL_CCC) bits on both ends of the
Link. This is done by pcie_aspm_configure_common_clock().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Brian Norris <briannorris@chromium.org>
Cc: jeffy.chen <jeffy.chen@rock-chips.com>
|
|
Adds a new endpoint function driver (to program the virtual test device)
making use of the EP-core library.
[bhelgaas: fold in pci_epf_test_probe() -ENOMEM test from Wei Yongjun
<weiyongjun1@huawei.com>]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Invoke APIs provided by pci-ep-cfs to create configfs entry for every EPC
device and EPF driver to help users in creating EPF device and binding the
EPF device to the EPC device.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Introduce a new configfs entry to configure the EP function (like
configuring the standard configuration header entries) and to bind the EP
function with EP controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Introduce a new EP core layer in order to support endpoint functions in
linux kernel. This comprises the EPC library (Endpoint Controller Library)
and EPF library (Endpoint Function Library). EPC library implements
functions specific to an endpoint controller and EPF library implements
functions specific to an endpoint function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Unused now that all callers switched to pci_alloc_irq_vectors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Linux 4.11-rc6
drm-misc needs 4.11-rc5, may as well fix conflicts with rc6.
|
|
Save a bit of time and avoid going through link speed change procedure in
configuration where link max speed is limited to Gen1 in DT.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: yurovsky@gmail.com
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Dong Aisheng <dongas86@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
|
|
As can be seen from [1]:
"...the different behavior between iMX6Q PCIe and iMX7D PCIe maybe caused
by the different controller version.
Regarding to the DOC description, the DIRECT_SPEED_CHANGE should be
cleared after the speed change from GEN1 to GEN2. Unfortunately, when
GEN1 device is used, the behavior is not documented.
So, IC design guys run the simulation and find out the following
behaviors:
1. DIRECT_SPEED_CHANGE will be cleared in 7D after speed change
from GEN1 to GEN2. This matches doc’s description
2. set MAX link speed(PCIE_CAP_TARGET_LINK_SPEED=0x01) as GEN1 and
re-run the simulation, DIRECT_SPEED_CHANGE will not be cleared;
remain as 1, this matches your result, but function test is
passed, so this bit should not affect the normal PCIe function."
imx6_pcie_wait_for_speed_change() will report false failures for Gen1 ->
Gen1 speed transition, so avoid doing that check and just rely on
imx6_pcie_wait_for_link() only.
[1] https://community.nxp.com/message/867943
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: yurovsky@gmail.com
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Dong Aisheng <dongas86@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
|
|
Some designs implement reset GPIO via a GPIO expander connected to a
peripheral bus. One such example would be i.MX7 Sabre board where said
GPIO is provided by SPI shift register connected to a bitbanged SPI bus.
To support such designs, allow reset GPIO request to defer probing of the
driver.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: yurovsky@gmail.com
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Dong Aisheng <dongas86@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
|
|
Add various bits of code needed to support i.MX7D variant of the IP.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Cc: yurovsky@gmail.com
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Dong Aisheng <dongas86@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
|
|
The memory allocation here needs to be non-blocking. Fix the issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org>
|
|
When we have 32 or more CPUs in the affinity mask, we should use a special
constant to specify that to the host. Fix this issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org>
|
|
There is no pci_cfg_access_unlocked(). I think the author meant
pci_cfg_access_unlock().
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Currently devm_request_irq() is being called before base, PCI fields of
dra7xx_pcie structure are populated. It is called even before
pm_runtime_enable() and pm_runtime_get_sync() are called. This will lead
to exceptions if in case an interrupt is triggered before the all of the
above are done. Hence push the devm_request_irq() call to the end of the
probe.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
No functional change. Rename dw_pcie_writel_unroll/dw_pcie_readl_unroll to
dw_pcie_writel_ob_unroll/dw_pcie_readl_ob_unroll respectively as these
functions are used to perform only outbound configurations. Also move
these _unroll configurations to a separate function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Previously dbi accessors can be used to access data of size 4 bytes. But
there might be situations (like accessing MSI_MESSAGE_CONTROL in order to
set/get the number of required MSI interrupts in EP mode) where dbi
accessors must be used to access data of size 2. This is in preparation
for adding endpoint mode support to designware driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Niklas Cassel <niklas.cassel@axis.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Joao Pinto <Joao.Pinto@synopsys.com>
|
|
dwc has 2 dbi address space labeled dbics and dbics2. The existing helper
to access dbi address space can access only dbics. However dbics2 has to
be accessed for programming the BAR registers in the case of EP mode. This
is in preparation for adding EP mode support to dwc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Niklas Cassel <niklas.cassel@axis.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Joao Pinto <Joao.Pinto@synopsys.com>
|
|
Populate cpu_addr_fixup ops to extract the least 28 bits of the
corresponding CPU address.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
|
|
Populate cpu_addr_fixup ops to extract the least 28 bits of the
corresponding CPU address.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
|
|
Some platforms (like dra7xx) require only the least 28 bits of the
corresponding 32 bit CPU address to be programmed in the address
translation unit. This modified address is stored in io_base/mem_base/
cfg0_base/cfg1_base in dra7xx_pcie_host_init(). While this is okay for
host mode where the address range is fixed, device mode requires different
addresses to be programmed based on the host buffer address. Add a new
ops to get the least 28 bits of the corresponding 32 bit CPU address and
invoke it before programming the address translation unit.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
|
|
The bug is that "val" is unsigned long but we only initialize 32 bits of
it. Then we test "if (val)" and that might be true not because we set the
bits but because some were never initialized.
Fixes: f342d940ee0e ("PCI: exynos: Add support for MSI")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use "continue" to skip rest of the loop when possible to save an indent
level. No functional change intended.
Suggested-by: walter harms <wharms@bfs.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Fix a crash from dereferencing a NULL dw_pcie_ops pointer. For example,
on ARTPEC-6:
Unable to handle kernel NULL pointer dereference at virtual address 00000004
pgd = c0204000
[00000004] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.11.0-rc3-next-20170321 #1
Hardware name: Axis ARTPEC-6 Platform
task: db098000 task.stack: db096000
PC is at dw_pcie_writel_dbi+0x2c/0xd0
Prior to 442ec4c04d12 ("PCI: dwc: all: Split struct pcie_port into
host-only and core structures"), every driver had a struct pcie_host_ops
with function pointers, typically used as:
if (pp->ops->readl_rc)
return pp->ops->readl_rc(...);
442ec4c04d12 split struct pcie_host_ops into two pieces: struct
dw_pcie_host_ops and struct dw_pcie_ops, so the above became:
if (pci->ops->readl_dbi)
return pci->ops->readl_dbi(...);
But pcie-artpec6.c and pcie-designware-plat.c don't need the dw_pcie_ops
pointers and didn't supply a pci->ops struct, which leads to NULL pointer
dereferences.
Supply an empty struct dw_pcie_ops to avoid the NULL pointer dereferences.
[bhelgaas: changelog]
Fixes: 442ec4c04d12 ("PCI: dwc: all: Split struct pcie_port into host-only and core structures")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
|
|
Without PCI_HOST_COMMON support enabled, we get a link error:
drivers/pci/dwc/built-in.o: In function `hisi_pcie_map_bus':
pcie-hisi.c:(.text+0x8860): undefined reference to `pci_ecam_map_bus'
drivers/pci/dwc/built-in.o: In function `hisi_pcie_almost_ecam_probe':
pcie-hisi.c:(.text+0x88b4): undefined reference to `pci_host_common_probe'
Add an explicit 'select', as the other users have.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
|
|
Rockchip Root Ports support either 64 or 128 byte Read Completion Boundary
(RCB). Set the RCB bit in the Link Control register to indicate this.
A 128 byte RCB significantly improves performance of NVMe with libaio.
[bhelgaas: changelog]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
|
|
Per Intel Specification Update 335553-002 (see link below), some 82579
network adapters advertise a Function Level Reset (FLR) capability, but
they can hang when an FLR is triggered.
To reproduce the problem, attach the device to a VM, then detach and try to
attach again.
Add a quirk to prevent the use of FLR on these devices.
[bhelgaas: changelog, comments]
Link: http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/82579lm-82579v-gigabit-network-connection-spec-update.pdf
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
SZ_16M PEM resource size includes PEM-specific register and its children
resources. Reservation of the whole SZ_16M range leads to child device
driver failure when pcieport driver is requesting resources:
pcieport 0004:1f:00.0: can't enable device: BAR 0 [mem 0x87e0c0f00000-0x87e0c0ffffff 64bit] not claimed
So we cannot reserve full 16M here and instead we want to reserve
PEM-specific register only which is SZ_64K.
At the end increase PEM resource to SZ_16M since this is what
thunder_pem_init() call expects for proper initialization.
Fixes: 9abb27c7594a ("PCI: thunder-pem: Add legacy firmware support for Cavium ThunderX host controller")
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.10+
|
|
./lib/string.c:134: WARNING: Inline emphasis start-string without end-string.
./mm/filemap.c:522: WARNING: Inline interpreted text or phrase reference start-string without end-string.
./mm/filemap.c:1283: ERROR: Unexpected indentation.
./mm/filemap.c:3003: WARNING: Inline interpreted text or phrase reference start-string without end-string.
./mm/vmalloc.c:1544: WARNING: Inline emphasis start-string without end-string.
./mm/page_alloc.c:4245: ERROR: Unexpected indentation.
./ipc/util.c:676: ERROR: Unexpected indentation.
./drivers/pci/irq.c:35: WARNING: Block quote ends without a blank line; unexpected unindent.
./security/security.c:109: ERROR: Unexpected indentation.
./security/security.c:110: WARNING: Definition list ends without a blank line; unexpected unindent.
./block/genhd.c:275: WARNING: Inline strong start-string without end-string.
./block/genhd.c:283: WARNING: Inline strong start-string without end-string.
./include/linux/clk.h:134: WARNING: Inline emphasis start-string without end-string.
./include/linux/clk.h:134: WARNING: Inline emphasis start-string without end-string.
./ipc/util.c:477: ERROR: Unknown target name: "s".
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Only apply the Cavium ACS quirk to devices with ID in the range
0xa000-0xa0ff. These are the on-chip PCI devices for CN81xx/CN83xx/CN88xx.
Fixes: b404bcfbf035 ("PCI: Add ACS quirk for all Cavium devices")
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Manish Jaggi <mjaggi@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Detect on probe whether a PCI device is part of a Thunderbolt controller.
Intel uses a Vendor-Specific Extended Capability (VSEC) with ID 0x1234
on such devices. Detect presence of this VSEC and cache it in a newly
added is_thunderbolt bit in struct pci_dev.
Also, add a helper to check whether a given PCI device is situated on a
Thunderbolt daisy chain (i.e., below a PCI device with is_thunderbolt
set).
The necessity arises from the following:
* If an external Thunderbolt GPU is connected to a dual GPU laptop,
that GPU is currently registered with vga_switcheroo even though it
can neither drive the laptop's panel nor be powered off by the
platform. To vga_switcheroo it will appear as if two discrete
GPUs are present. As a result, when the external GPU is runtime
suspended, vga_switcheroo will cut power to the internal discrete GPU
which may not be runtime suspended at all at this moment. The
solution is to not register external GPUs with vga_switcheroo, which
necessitates a way to recognize if they're on a Thunderbolt daisy
chain.
* Dual GPU MacBook Pros introduced 2011+ can no longer switch external
DisplayPort ports between GPUs. (They're no longer just used for DP
but have become combined DP/Thunderbolt ports.) The driver to switch
the ports, drivers/platform/x86/apple-gmux.c, needs to detect presence
of a Thunderbolt controller and, if found, keep external ports
permanently switched to the discrete GPU.
v2: Make kerneldoc for pci_is_thunderbolt_attached() more precise,
drop portion of commit message pertaining to separate series.
(Bjorn Helgaas)
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Amir Levy <amir.jer.levy@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: http://patchwork.freedesktop.org/patch/msgid/0ab165a4a35c0b60f29d4c306c653ead14fcd8f9.1489145162.git.lukas@wunner.de
|
|
If the PCI device is disconnected, return false immediately from
pci_device_is_present(). pci_device_is_present() uses the bus accessors,
so the early return in the device accessors doesn't help here.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Wei Zhang <wzhang@fb.com>
|
|
Check the device connected state prior to executing device shutdown
operations or writing MSI messages so that tear down on disconnected
devices completes quicker.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Wei Zhang <wzhang@fb.com>
|
|
If we've detected the PCI device is disconnected, there is no need to
attempt to access its config space since we know the operation will fail.
Make all the config reads and writes return -ENODEV error immediately when
in such a state.
If a caller requests a config read to a disconnected device, return a data
value of all 1's. This is the same as what hardware is expected to return
when accessing a removed device, but software can do this faster without
relying on hardware.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Wei Zhang <wzhang@fb.com>
|
|
Add a new state to pci_dev to be set when it is unexpectedly disconnected.
The PCI driver tear down functions can observe this new device state so
they may skip operations that will fail.
The pciehp and pcie-dpc drivers are aware when the link is down, so these
set the flag when their handlers detect the device is disconnected.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Wei Zhang <wzhang@fb.com>
|
|
Replace the inline PCI device config read and write accessors with exported
functions. This is preparing for these functions to make use of private
data.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Wei Zhang <wzhang@fb.com>
|
|
It seems on later Armada 38x, the slot clock configuration bit is not
read-only, but can be written. This means that our RW1C protection ends up
clearing this bit when the link control register is written.
Adjust the mask so that we only avoid writing '1' bits to the RW1C bits of
this register (bits 15 and 14 of the link status) rather than masking out
all the status register bits.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add a host bridge driver for the Faraday Technology FPPCI100 host bridge,
used for Cortina Systems Gemini SoC (SL3516) PCI Host Bridge.
This code is inspired by the out-of-tree OpenWRT patch and then extensively
rewritten for device tree and using the modern helpers to cut down and
modernize the code to all new PCI frameworks. A driver exists in U-Boot as
well.
Tested on the ITian Square One SQ201 NAS with the following result in the
boot log (trimmed to relevant parts):
OF: PCI: host bridge /soc/pci@50000000 ranges:
OF: PCI: IO 0x50000000..0x500fffff -> 0x00000000
OF: PCI: MEM 0x58000000..0x5fffffff -> 0x58000000
ftpci100 50000000.pci: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0x58000000-0x5fffffff]
ftpci100 50000000.pci:
DMA MEM1 BASE: 0x0000000000000000 -> 0x0000000007ffffff config 00070000
ftpci100 50000000.pci:
DMA MEM2 BASE: 0x0000000000000000 -> 0x0000000003ffffff config 00060000
ftpci100 50000000.pci:
DMA MEM3 BASE: 0x0000000000000000 -> 0x0000000003ffffff config 00060000
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:00.0: of_irq_parse_pci() failed with rc=-22
pci 0000:00:0c.0: BAR 0: assigned [mem 0x58000000-0x58007fff]
pci 0000:00:09.2: BAR 0: assigned [mem 0x58008000-0x580080ff]
pci 0000:00:09.0: BAR 4: assigned [io 0x1000-0x101f]
pci 0000:00:09.1: BAR 4: assigned [io 0x1020-0x103f]
pci 0000:00:09.0: enabling device (0140 -> 0141)
pci 0000:00:09.0: HCRESET not completed yet!
pci 0000:00:09.1: enabling device (0140 -> 0141)
pci 0000:00:09.1: HCRESET not completed yet!
pci 0000:00:09.2: enabling device (0140 -> 0142)
rt61pci 0000:00:0c.0: enabling device (0140 -> 0142)
ieee80211 phy0: rt2x00_set_chip: Info - Chipset detected -
rt: 2561, rf: 0003, rev: 000c
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:09.2: EHCI Host Controller
ehci-pci 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:09.2: irq 125, io mem 0x58008000
ehci-pci 0000:00:09.2: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:09.0: UHCI Host Controller
uhci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:09.0: HCRESET not completed yet!
uhci_hcd 0000:00:09.0: irq 123, io base 0x00001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
uhci_hcd 0000:00:09.1: UHCI Host Controller
uhci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:09.1: HCRESET not completed yet!
uhci_hcd 0000:00:09.1: irq 124, io base 0x00001020
hub 3-0:1.0: USB hub found
hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
scsi 0:0:0:0: Direct-Access USB Flash Disk 1.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 7900336 512-byte logical blocks: (4.04 GB/3.77 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] No Caching mode page found
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI removable disk
ieee80211 phy0: rt2x00lib_request_firmware: Info -
Loading firmware file 'rt2561s.bin'
ieee80211 phy0: rt2x00lib_request_firmware: Info -
Firmware detected - version: 0.8
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
$ lspci
00:00.0 Class 0600: 159b:4321
00:09.2 Class 0c03: 1106:3104
00:09.0 Class 0c03: 1106:3038
00:09.1 Class 0c03: 1106:3038
00:0c.0 Class 0280: 1814:0301
$ cat /proc/interrupts
CPU0
123: 0 PCI 0 Edge uhci_hcd:usb2
124: 0 PCI 1 Edge uhci_hcd:usb3
125: 159 PCI 2 Edge ehci_hcd:usb1
126: 1082 PCI 3 Edge rt61pci
$ cat /proc/iomem
50000000-500000ff : /soc/pci@50000000
58000000-5fffffff : Gemini PCI MEM
58000000-58007fff : 0000:00:0c.0
58000000-58007fff : 0000:00:0c.0
58008000-580080ff : 0000:00:09.2
58008000-580080ff : ehci_hcd
The EHCI USB hub works fine; I can mount and manage files and the IRQs just
keep ticking up. I can issue iwlist wlan0 scanning and see all the WLANs
here. I don't have wpa_supplicant so have not tried connecting to them.
[bhelgaas: fold in %pap change from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Janos Laube <janos.dev@gmail.com>
CC: Paulius Zaleckas <paulius.zaleckas@gmail.com>
CC: Hans Ulli Kroll <ulli.kroll@googlemail.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Feng-Hsin Chiang <john453@faraday-tech.com>
CC: Greentime Hu <green.hu@gmail.com>
|
|
A PCI_EJECT message can arrive at the same time we are calling
pci_scan_child_bus() in the workqueue for the previous PCI_BUS_RELATIONS
message or in create_root_hv_pci_bus(). In this case we could potentially
modify the bus from multiple places.
Properly lock the bus access.
Thanks Dexuan Cui <decui@microsoft.com> for pointing out the race condition
in create_root_hv_pci_bus().
Reported-by: Xiaofeng Wang <xiaofwan@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
|
|
hv_pci_devices_present() is called in hv_pci_remove() when we remove a PCI
device from the host, e.g., by disabling SR-IOV on a device. In
hv_pci_remove(), the bus is already removed before the call, so we don't
need to rescan the bus in the workqueue scheduled from
hv_pci_devices_present().
By introducing bus state hv_pcibus_removed, we can avoid this situation.
Reported-by: Xiaofeng Wang <xiaofwan@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
|
|
There's no way to get here with 'err != 0'. Just return 0 to be more
obvious and prevent future changes from accidentally erroring out here
without going through the right error paths.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If regulator_get_current_limit() returns 0 or error, return early so the
body of the function doesn't have to be indented as the body of an "if"
statement. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
controller
During early days of PCI quirks support, ThunderX firmware did not provide
PNP0c02 node with PCI configuration space and PEM-specific register ranges.
This means that for legacy FW we are not reserving these resources and
cannot gather PEM-specific resources for further PEM initialization.
To support already deployed legacy FW, calculate PEM-specific ranges and
provide resources reservation as fallback scenario into PEM driver when we
could not gather PEM reg base from ACPI tables.
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
|
|
"CAV" is the only PNP/ACPI hardware ID vendor prefix assigned to Cavium so
fix this as it should be from day one.
Fixes: 44f22bd91e88 ("PCI: Add MCFG quirks for Cavium ThunderX pass2.x host controller")
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
|
