| Age | Commit message (Collapse) | Author |
|---|
|
Kernel hang is observed when pci-hyperv module is release with device
drivers still attached. E.g., when I do 'rmmod pci_hyperv' with BCM5720
device pass-through-ed (tg3 module) I see the following:
NMI watchdog: BUG: soft lockup - CPU#1 stuck for 22s! [rmmod:2104]
...
Call Trace:
[<ffffffffa0641487>] tg3_read_mem+0x87/0x100 [tg3]
[<ffffffffa063f000>] ? 0xffffffffa063f000
[<ffffffffa0644375>] tg3_poll_fw+0x85/0x150 [tg3]
[<ffffffffa0649877>] tg3_chip_reset+0x357/0x8c0 [tg3]
[<ffffffffa064ca8b>] tg3_halt+0x3b/0x190 [tg3]
[<ffffffffa0657611>] tg3_stop+0x171/0x230 [tg3]
...
[<ffffffffa064c550>] tg3_remove_one+0x90/0x140 [tg3]
[<ffffffff813bee59>] pci_device_remove+0x39/0xc0
[<ffffffff814a3201>] __device_release_driver+0xa1/0x160
[<ffffffff814a32e3>] device_release_driver+0x23/0x30
[<ffffffff813b794a>] pci_stop_bus_device+0x8a/0xa0
[<ffffffff813b7ab6>] pci_stop_root_bus+0x36/0x60
[<ffffffffa02c3f38>] hv_pci_remove+0x238/0x260 [pci_hyperv]
The problem seems to be that we report local resources release before
stopping the bus and removing devices from it and device drivers may try to
perform some operations with these resources on shutdown. Move resources
release report after we do pci_stop_root_bus().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jake Oshins <jakeo@microsoft.com>
|
|
I.MX6+ has a dedicated bit for resetting PCIe core, which should be used
instead of a regular reset sequence since using the latter will hang the
SoC.
This commit is based on c34068d48273e24d392d9a49a38be807954420ed from
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Use enumerated type instead of a boolean flag to specify the variant of
the PCIe IP block (6Q, 6SX, etc). This patch has zero functional impact,
however it makes the code easier to extend for the case of more than 2
possible variants of an IP block (of which there are).
[bhelgaas: rewrap comment, remove extra blank line]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Linux 4.5 introduced a behavioral change in device probing during the
suspend process with commit 013c074f8642 ("PM / sleep: prohibit devices
probing during suspend/hibernation"): It defers device probing during the
entire suspend process, starting from the prepare phase and ending with the
complete phase. A rule existed before that "we rely on subsystems not to
do any probing once a device is suspended" but it is enforced only now
(Alan Stern, https://lkml.org/lkml/2015/9/15/908).
This resulted in a WARN splat if a PCI device (e.g., Thunderbolt) is
plugged in while the system is asleep: Upon waking up, pciehp_resume()
discovers new devices in the resume phase and immediately tries to bind
them to a driver. Since probing is now deferred, device_attach() returns
-EPROBE_DEFER, which provoked a WARN in pci_bus_add_device().
Linux 4.6-rc1 aggravates the situation with commit ab1a187bba5c ("PCI:
Check device_attach() return value always"): If device_attach() returns a
negative value, pci_bus_add_device() now removes the sysfs and procfs
entries for the device and pci_bus_add_devices() subsequently locks up with
a BUG. Even with the BUG fixed we're still in trouble because the device
remains on the deferred probing list even though its sysfs and procfs
entries are gone and its children won't be added.
Fix by not interpreting -EPROBE_DEFER as failure. The device will be
probed eventually (through device_unblock_probing() in dpm_complete()) and
there is proper locking in place to avoid races (e.g., if devices are
unplugged again und thus deleted from the system before deferred probing
happens, I have tested this). Also, those functions which dereference
dev->driver (e.g. pci_pm_*()) do contain proper NULL pointer checks. So it
seems safe to ignore -EPROBE_DEFER.
Fixes: ab1a187bba5c ("PCI: Check device_attach() return value always")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
|
|
Previously when pci_bus_add_device() called device_attach() and it returned
a negative value, we emitted a WARN but carried on.
Commit ab1a187bba5c ("PCI: Check device_attach() return value always"),
introduced in Linux 4.6-rc1, changed this to unwind all steps preceding
device_attach() and to not set dev->is_added = 1.
The latter leads to a BUG if pci_bus_add_device() was called from
pci_bus_add_devices(). Fix by not recursing to a child bus if
device_attach() failed for the bridge leading to it.
This can be triggered by plugging in a PCI device (e.g. Thunderbolt) while
the system is asleep. The system locks up when woken because
device_attach() returns -EPROBE_DEFER.
Fixes: ab1a187bba5c ("PCI: Check device_attach() return value always")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The 32-bit addressing modes in the I/O and Prefetchable Memory registers
are required to be read-only. Since the underlying access method allows
them to be set, emulate their read-only nature and always set them.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The R-Car PCIe driver requires the use of IRQ domains for its MSI code:
drivers/pci/host/pcie-rcar.c:635:9: error: implicit declaration of function 'irq_find_mapping' [-Werror=implicit-function-declaration]
drivers/pci/host/pcie-rcar.c:666:8: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration]
...
Add a Kconfig select to ensure that the feature is always enabled.
This is not consistent with what the other drivers do at the moment, but I
have another patch that changes them to do it like this one, which is more
logical.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch modifies all the callers of vmbus_mmio_allocate()
to call vmbus_mmio_free() instead of release_mem_region().
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current XUSB pad controller bindings are insufficient to describe
PHY devices attached to USB controllers. New bindings have been created
to overcome these restrictions. As a side-effect each root port now is
assigned a set of PHY devices, one for each lane associated with the
root port. This has the benefit of allowing fine-grained control of the
power management for each lane.
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Marvell Armada 7K/8K SoCs integrate a PCIe controller from Synopsys.
Add a new driver that provides the small glue needed to use the existing
Designware driver to make it work on Marvell Armada 7K/8K SoCs.
The MSI support will be enabled at a later point.
[bhelgaas: use dev_dbg(), dw_pcie_wait_for_link()]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
iomem_is_exclusive() requires a CPU physical address, but on some arches we
supplied a PCI bus address instead.
On most arches, pci_resource_to_user(res) returns "res->start", which is a
CPU physical address. But on microblaze, mips, powerpc, and sparc, it
returns the PCI bus address corresponding to "res->start".
The result is that pci_mmap_resource() may fail when it shouldn't (if the
bus address happens to match an existing resource), or it may succeed when
it should fail (if the resource is exclusive but the bus address doesn't
match it).
Call iomem_is_exclusive() with "res->start", which is always a CPU physical
address, not the result of pci_resource_to_user().
Fixes: e8de1481fd71 ("resource: allow MMIO exclusivity for device drivers")
Suggested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arjan van de Ven <arjan@linux.intel.com>
|
|
'pci/thunderbolt' and 'pci/virtualization' into next
* pci/enumeration:
x86/PCI: Refine PCI support check in pcibios_init()
* pci/hotplug:
PCI: acpiphp_ibm: Avoid uninitialized variable reference
* pci/misc:
PCI: Fix spelling errors
* pci/ntb:
PCI: Add DMA alias quirk for mic_x200_dma
PCI: Add support for multiple DMA aliases
PCI: Move informational printk to pci_add_dma_alias()
PCI: Add pci_add_dma_alias() to abstract implementation
* pci/thunderbolt:
thunderbolt: Support 1st gen Light Ridge controller
thunderbolt: Fix typos and magic number
PCI: Add Intel Thunderbolt device IDs
* pci/virtualization:
PCI: Work around Intel Sunrise Point PCH incorrect ACS capability
PCI: Reverse standard ACS vs device-specific ACS enabling
PCI: Mark Intel i40e NIC INTx masking as broken
|
|
Fix the misuse of goto statement in ks_pcie_get_irq_controller_info() as
simple return is more appropriate for this function. While at it add an
error log for absence of interrupt controller node.
[bhelgaas: drop "ret" altogether since we always know the return value]
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
|
|
It appears that Gen2 is a misnomer for the R-Car PCIE driver
which also supports Gen 1 and Gen 3 SoCs. Accordingly, drop Gen 2
from the help text and Kconfig symbol.
Also, re-arange the Kconfig symbol name to use PCIE as the prefix.
This appears to be in keeping with other PCIE Kconfig symbols.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Freescale has stated [1] that the LVDS clock source of the IMX6 does not
pass the PCI Gen2 clock jitter test, therefore unless an external Gen2
compliant external clock source is present and supplied back to the IMX6
PCIe core via LVDS CLK1/CLK2 you can not claim Gen2 compliance.
Add a DT property to specify Gen1 vs Gen2 and check this before allowing a
Gen2 link.
We default to Gen1 if the property is not present because at this time
there are no IMX6 boards in mainline that 'input' a clock on LVDS
CLK1/CLK2.
In order to be Gen2 compliant on IMX6 you need to:
- Have a Gen2 compliant external clock generator and route that clock back
to either LVDS CLK1 or LVDS CLK2 as an input (see IMX6SX-SabreSD
reference design).
- Specify this clock in the PCIe node in the DT (i.e.,
IMX6QDL_CLK_LVDS1_IN or IMX6QDL_CLK_LVDS2_IN instead of
IMX6QDL_CLK_LVDS1_GATE which configures it as a CLK output).
[1] https://community.freescale.com/message/453209
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Zhu Richard <Richard.Zhu@freescale.com>
CC: Akshay Bhat <akshay.bhat@timesys.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Shawn Guo <shawnguo@kernel.org>
|
|
Currently the reset-gpio DT property which controls the PCI bus device
reset signal defaults to active-low reset sequence (L=reset state,
H=operation state) plus the code in reset function isn't GPIO polarity
aware - it doesn't matter if the defined reset-gpio is active-low or
active-high, it will always result into active-low reset sequence.
I've tried to fix it properly and change the reset-gpio reset sequence to
be polarity-aware, but this patch has been accepted and then reverted as it
has introduced few backward incompatible issues:
1. Some DTBs, for example, imx6qdl-sabresd, don't define reset-gpio
polarity correctly:
reset-gpio = <&gpio7 12 0>;
which means that it's defined as active-high, but in reality it's
active-low; thus it wouldn't work without a DTS fix.
2. The logic in the reset function is inverted:
gpio_set_value_cansleep(imx6_pcie->reset_gpio, 0)
msleep(100);
gpio_set_value_cansleep(imx6_pcie->reset_gpio, 1);
so even if some of the i.MX6 boards had reset-gpio polarity defined
correctly in their DTSes, they would stop working.
As we can't break old DTBs, we can't fix them, so we need to introduce this
new DT reset-gpio-active-high boolean property so we can support boards
with active-high reset sequence.
This active-high reset sequence is for example needed on Apalis SoMs, where
GPIO1_IO28, used to PCIe reset is not connected directly to PERST# PCIe
signal, but it's ORed with RESETBMCU coming off the PMIC, and thus is
inverted, active-high.
Tested-by: Tim Harvey <tharvey@gateworks.com> # Gateworks Ventana boards (which have active-low PERST#)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Add initial PCIe support for the imx6 SoC derivate imx6sx. PCI MSI support
is untested as the necessary suspend/resume quirk is not included in this
patch.
This patch is heavily based on patches by Richard Zhu.
[bhelgaas: factor out refclk enable, fix adjacent typos in imx6q-pcie.txt]
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Acked-by: Richard Zhu <Richard.Zhu@freescale.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
|
|
Factor out ref clock enable to make it cleaner to add imx6sx support. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
|
|
Intel Sunrise Point root ports implement ACS but use dwords for the
capability and control registers, putting the control register at the wrong
offset.
Use quirks to enable and test ACS for these devices, which match the
standard functions modulo the broken control register offset.
Note that lspci assumes devices implement ACS per spec, so it shows invalid
ACS data for these devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The original thought was that if a device implemented ACS, then surely
we want to use that... well, it turns out that devices can make an ACS
capability so broken that we still need to fall back to quirks.
Reverse the order of ACS enabling to give quirks first shot at it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
All of the i40e (XL710/X710) 10/20/40GbE NICs lack support for indicating
INTx is asserted via the interrupt bit in the PCI status register. The
DisINTx bit in the command register is functional, causing these devices to
be incorrectly detected as supporting INTx masking. Quirk them to properly
indicate no INTx masking support.
Device IDs copied from i40e_devids.h.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for two issues:
- The VPD parsing code we added for v4.6 keeps some devices from
crashing, but also keeps cxgb4 from reading non-standard extra VPD
data that is relies on. Hariprasad added a way for the driver to
specify how much VPD is valid.
- The i.MX6 active-low reset GPIO support we added in v4.5 caused
regressions on some boards, so we're reverting that.
VPD:
Add pci_set_vpd_size() (Hariprasad Shenai)
cxgb4: Set VPD size so we can read both VPD structures (Hariprasad Shenai)
Freescale i.MX6 host bridge driver:
Revert "PCI: imx6: Add support for active-low reset GPIO" (Fabio Estevam)"
* tag 'pci-v4.6-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
cxgb4: Set VPD size so we can read both VPD structures
PCI: Add pci_set_vpd_size() to set VPD size
Revert "PCI: imx6: Add support for active-low reset GPIO"
|
|
After 104daa71b396 ("PCI: Determine actual VPD size on first access"), the
PCI core computes the valid VPD size by parsing the VPD starting at offset
0x0. We don't attempt to read past that valid size because that causes
some devices to crash.
However, some devices do have data past that valid size. For example,
Chelsio adapters contain two VPD structures, and the driver needs both of
them.
Add pci_set_vpd_size(). If a driver knows it is safe to read past the end
of the VPD data structure at offset 0, it can use pci_set_vpd_size() to
allow access to as much data as it needs.
[bhelgaas: changelog, split patches, rename to pci_set_vpd_size() and
return int (not ssize_t)]
Fixes: 104daa71b396 ("PCI: Determine actual VPD size on first access")
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If ibm_get_table_from_acpi() fails then "table" isn't initialized. Check
for failure so we don't reference "table" unless it's been initialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The PCI config access checked the file capabilities correctly, but used
the itnernal security capability check rather than the helper function
that is actually meant for that.
The security_capable() has unusual return values and is not meant to be
used elsewhere (the only other use is in the capability checking
functions that we actually intend people to use, and this odd PCI usage
really stood out when looking around the capability code.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Keystone PCI hardware generates error interrupts at RC using a platform IRQ
instead of a standard MSI or legacy IRQ. Add a simple error handler that
logs the fatal interrupt status to the console.
[bhelgaas: s/node/dev->of_node/, tidy comments, return irqreturn_t directly]
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
|
|
The MIC x200 NTB forwards DMA transactions upstream using multiple alien
RIDs. These RIDs have to be added as aliases to the DMA device to allow
buffer access when the IOMMU is enabled.
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Solve IOMMU support issues with PCIe non-transparent bridges that use
Requester ID look-up tables (RID-LUT), e.g., the PEX8733.
The NTB connects devices in two independent PCI domains. Devices separated
by the NTB are not able to discover each other. A PCI packet being
forwared from one domain to another has to have its RID modified so it
appears on correct bus and completions are forwarded back to the original
domain through the NTB. The RID is translated using a preprogrammed table
(LUT) and the PCI packet propagates upstream away from the NTB. If the
destination system has IOMMU enabled, the packet will be discarded because
the new RID is unknown to the IOMMU. Adding a DMA alias for the new RID
allows IOMMU to properly recognize the packet.
Each device behind the NTB has a unique RID assigned in the RID-LUT. The
current DMA alias implementation supports only a single alias, so it's not
possible to support mutiple devices behind the NTB when IOMMU is enabled.
Enable all possible aliases on a given bus (256) that are stored in a
bitset. Alias devfn is directly translated to a bit number. The bitset is
not allocated for devices that have no need for DMA aliases.
More details can be found in the following article:
http://www.plxtech.com/files/pdf/technical/expresslane/RTC_Enabling%20MulitHostSystemDesigns.pdf
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
|
|
One of the quirks that adds DMA aliases logs an informational message in
dmesg. Move that to pci_add_dma_alias() so all users log the message
consistently. No functional change intended (except extra message).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Add a pci_add_dma_alias() interface to encapsulate the details of adding an
alias. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Now that pcie_port_acpi_setup() always returns 0, make it and its callers
void functions and stop checking the return values.
[bhelgaas: changelog]
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Host bridges we discover via ACPI, i.e., PNP0A03 and PNP0A08 devices, may
have an _OSC method by which the OS can ask the platform for control of
PCIe features like native hotplug, power management events, AER, etc.
Previously, if we found a bridge without an ACPI device, we assumed we did
not have permission to use any of these PCIe features. That seems
unreasonably restrictive.
If we find no ACPI device, assume we can take control of all PCIe features.
The Intel Volume Management Device (VMD) is one such bridge with no ACPI
device. Prior to this change, users had to boot with "pcie_ports=native"
to get hotplug and other services to work below the VMD Root Port.
[bhelgaas: changelog]
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add support for the 1st gen Light Ridge controller, which is built into
these systems:
iMac12,1 2011 21.5"
iMac12,2 2011 27"
Macmini5,1 2011 i5 2.3 GHz
Macmini5,2 2011 i5 2.5 GHz
Macmini5,3 2011 i7 2.0 GHz
MacBookPro8,1 2011 13"
MacBookPro8,2 2011 15"
MacBookPro8,3 2011 17"
MacBookPro9,1 2012 15"
MacBookPro9,2 2012 13"
Light Ridge (CV82524) was the very first copper Thunderbolt controller,
introduced 2010 alongside its fiber-optic cousin Light Peak (CVL2510).
Consequently the chip suffers from some teething troubles:
- MSI is broken for hotplug signaling on the downstream bridges: The chip
just never sends an interrupt. It requests 32 MSIs for each of its six
bridges and the pcieport driver only allocates one per bridge. However
I've verified that even if 32 MSIs are allocated there's no interrupt
on hotplug. The only option is thus to disable MSI, which is also what
OS X does. Apparently all Thunderbolt chips up to revision 1 of Cactus
Ridge 4C are plagued by this issue so quirk those as well.
- The chip supports a maximum hop_count of 32, unlike its successors
which support only 12. Fixup ring_interrupt_active() to cope with
values >= 32.
- Another peculiarity is that the chip supports a maximum of 13 ports
whereas its successors support 12. However the additional port (#5)
seems to be unusable as reading its TB_CFG_PORT config space results in
TB_CFG_ERROR_INVALID_CONFIG_SPACE. Add a quirk to mark the port
disabled on the root switch, assuming that's necessary on all Macs
using this chip.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: William Brown <william@blackhats.net.au> [MacBookPro8,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
|
|
Intel Gen 1 and 2 chips use the same ID for NHI, bridges and switch. Gen 3
chips and onward use a distinct ID for the NHI.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
|
|
Use the SET_NOIRQ_SYSTEM_SLEEP_PM_OPS helper macro for mvebu_pcie_pm_ops.
The macro also sets up freeze_noirq, thaw_noirq and poweroff_noirq,
restore_noirq accordingly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
The mvebu_pcie_pm_ops structure is never modified, so declare it as const.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
dw_pcie_host_init() looks up host bridge resources, ioremaps them, creates
IRQ domains, and enumerates devices below the bridge. dw_pcie_setup_rc()
programs the Root Complex registers. The Root Complex may lose power
during suspend-to-RAM, and when we resume, we want to redo the latter but
not the former.
Move some Root Complex programming from dw_pcie_host_init() to
dw_pcie_setup_rc() where it belongs. DesignWare-based drivers can call
dw_pcie_setup_rc() in their resume paths.
[Niklas Cassel <niklas.cassel@axis.com>: This change moves outbound ATU
programming, which uses pp->mem_base, to dw_pcie_setup_rc(). Apply the
dra7xx pp->mem_base update before calling dw_pcie_setup_rc().]
[bhelgaas: changelog, fold in dra7xx fix from Niklas]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
|
|
Commit 5c5fb40de8f1 ("PCI: imx6: Add support for active-low reset GPIO")
cause regressions on some boards like MX6 Gateworks Ventana, for example.
The reason for the breakage is that this commit sets the GPIO polarity in
the wrong logic level.
Also, the commit log is wrong because active-low reset GPIO is what the
driver used to support since the beginning.
So keep the old behavior that ignores the GPIO polarity specified in the
device tree and treat the PCI reset GPIO as active-low.
Reported-by: Krzysztof Hałasa <khalasa@piap.pl>
Tested-by: Tim Harvey <tharvey@gateworks.com> # Gateworks Ventana
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
CC: stable@vger.kernel.org # v4.5+
|
|
Fix spelling of "initalization".
[bhelgaas: also fix pci/pci.c]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Revert 5c3b99d05752 ("PCI: dra7xx: Mark driver as broken").
1c96bee4df19 ("ARM: DRA7: hwmod: Add custom reset handler for PCIeSS")
added support to de-assert PCIe reset, so DRA7x PCIe is not broken anymore.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Commit e7e127e3c767 ("PCI: Include pci/hotplug Kconfig directly from
pci/Kconfig") added one line to pci/Kconfig. However, for some mysterious
reason it isn't there now, even though there are no traces of removing it
in the git log.
I detected this issue when 'make oldconfig' removed all the options that
depended on HOTPLUG_PCI.
[bhelgaas: I botched the cfeb8139a1fb ("Merge branch 'pci/host-hv' into
next") merge. "git diff cfeb8139a1fb^ cfeb8139a1fb" shows a conflict in
drivers/pci/Kconfig, and I mistakenly dropped the hotplug/Kconfig piece.]
Signed-off-by: Tero Roponen <tero.roponen@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This was delayed a day or two by some build-breakage on old toolchains
which we've now fixed.
There's two PCI commits both acked by Bjorn.
There's one commit to mm/hugepage.c which is (co)authored by Kirill.
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul
Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh
Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy,
Cyril Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell
Currey, Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_*
helpers from Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/
relaxed variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas
Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs
from Wei Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell
Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev
Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter
values, display domain indices in sysfs, eliminate domain suffix in
event names, from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit
checksum optimizations, 86xx consolidation, e5500/e6500 cpu
hotplug, more fman and other dt bits, and minor fixes/cleanup"
* tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (179 commits)
powerpc: Fix unrecoverable SLB miss during restore_math()
powerpc/8xx: Fix do_mtspr_cpu6() build on older compilers
powerpc/rcpm: Fix build break when SMP=n
powerpc/book3e-64: Use hardcoded mttmr opcode
powerpc/fsl/dts: Add "jedec,spi-nor" flash compatible
powerpc/T104xRDB: add tdm riser card node to device tree
powerpc32: PAGE_EXEC required for inittext
powerpc/mpc85xx: Add pcsphy nodes to FManV3 device tree
powerpc/mpc85xx: Add MDIO bus muxing support to the board device tree(s)
powerpc/86xx: Introduce and use common dtsi
powerpc/86xx: Update device tree
powerpc/86xx: Move dts files to fsl directory
powerpc/86xx: Switch to kconfig fragments approach
powerpc/86xx: Update defconfigs
powerpc/86xx: Consolidate common platform code
powerpc32: Remove one insn in mulhdu
powerpc32: small optimisation in flush_icache_range()
powerpc: Simplify test in __dma_sync()
powerpc32: move xxxxx_dcache_range() functions inline
powerpc32: Remove clear_pages() and define clear_page() inline
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes for v4.6:
Enumeration:
- Disable IO/MEM decoding for devices with non-compliant BARs (Bjorn Helgaas)
- Mark Broadwell-EP Home Agent & PCU as having non-compliant BARs (Bjorn Helgaas
Resource management:
- Mark shadow copy of VGA ROM as IORESOURCE_PCI_FIXED (Bjorn Helgaas)
- Don't assign or reassign immutable resources (Bjorn Helgaas)
- Don't enable/disable ROM BAR if we're using a RAM shadow copy (Bjorn Helgaas)
- Set ROM shadow location in arch code, not in PCI core (Bjorn Helgaas)
- Remove arch-specific IORESOURCE_ROM_SHADOW size from sysfs (Bjorn Helgaas)
- ia64: Use ioremap() instead of open-coded equivalent (Bjorn Helgaas)
- ia64: Keep CPU physical (not virtual) addresses in shadow ROM resource (Bjorn Helgaas)
- MIPS: Keep CPU physical (not virtual) addresses in shadow ROM resource (Bjorn Helgaas)
- Remove unused IORESOURCE_ROM_COPY and IORESOURCE_ROM_BIOS_COPY (Bjorn Helgaas)
- Don't leak memory if sysfs_create_bin_file() fails (Bjorn Helgaas)
- rcar: Remove PCI_PROBE_ONLY handling (Lorenzo Pieralisi)
- designware: Remove PCI_PROBE_ONLY handling (Lorenzo Pieralisi)
Virtualization:
- Wait for up to 1000ms after FLR reset (Alex Williamson)
- Support SR-IOV on any function type (Kelly Zytaruk)
- Add ACS quirk for all Cavium devices (Manish Jaggi)
AER:
- Rename pci_ops_aer to aer_inj_pci_ops (Bjorn Helgaas)
- Restore pci_ops pointer while calling original pci_ops (David Daney)
- Fix aer_inject error codes (Jean Delvare)
- Use dev_warn() in aer_inject (Jean Delvare)
- Log actual error causes in aer_inject (Jean Delvare)
- Log aer_inject error injections (Jean Delvare)
VPD:
- Prevent VPD access for buggy devices (Babu Moger)
- Move pci_read_vpd() and pci_write_vpd() close to other VPD code (Bjorn Helgaas)
- Move pci_vpd_release() from header file to pci/access.c (Bjorn Helgaas)
- Remove struct pci_vpd_ops.release function pointer (Bjorn Helgaas)
- Rename VPD symbols to remove unnecessary "pci22" (Bjorn Helgaas)
- Fold struct pci_vpd_pci22 into struct pci_vpd (Bjorn Helgaas)
- Sleep rather than busy-wait for VPD access completion (Bjorn Helgaas)
- Update VPD definitions (Hannes Reinecke)
- Allow access to VPD attributes with size 0 (Hannes Reinecke)
- Determine actual VPD size on first access (Hannes Reinecke)
Generic host bridge driver:
- Move structure definitions to separate header file (David Daney)
- Add pci_host_common_probe(), based on gen_pci_probe() (David Daney)
- Expose pci_host_common_probe() for use by other drivers (David Daney)
Altera host bridge driver:
- Fix altera_pcie_link_is_up() (Ley Foon Tan)
Cavium ThunderX host bridge driver:
- Add PCIe host driver for ThunderX processors (David Daney)
- Add driver for ThunderX-pass{1,2} on-chip devices (David Daney)
Freescale i.MX6 host bridge driver:
- Add DT bindings to configure PHY Tx driver settings (Justin Waters)
- Move imx6_pcie_reset_phy() near other PHY handling functions (Lucas Stach)
- Move PHY reset into imx6_pcie_establish_link() (Lucas Stach)
- Remove broken Gen2 workaround (Lucas Stach)
- Move link up check into imx6_pcie_wait_for_link() (Lucas Stach)
Freescale Layerscape host bridge driver:
- Add "fsl,ls2085a-pcie" compatible ID (Yang Shi)
Intel VMD host bridge driver:
- Attach VMD resources to parent domain's resource tree (Jon Derrick)
- Set bus resource start to 0 (Keith Busch)
Microsoft Hyper-V host bridge driver:
- Add fwnode_handle to x86 pci_sysdata (Jake Oshins)
- Look up IRQ domain by fwnode_handle (Jake Oshins)
- Add paravirtual PCI front-end for Microsoft Hyper-V VMs (Jake Oshins)
NVIDIA Tegra host bridge driver:
- Add pci_ops.{add,remove}_bus() callbacks (Thierry Reding)
- Implement ->{add,remove}_bus() callbacks (Thierry Reding)
- Remove unused struct tegra_pcie.num_ports field (Thierry Reding)
- Track bus -> CPU mapping (Thierry Reding)
- Remove misleading PHYS_OFFSET (Thierry Reding)
Renesas R-Car host bridge driver:
- Depend on ARCH_RENESAS, not ARCH_SHMOBILE (Simon Horman)
Synopsys DesignWare host bridge driver:
- ARC: Add PCI support (Joao Pinto)
- Add generic dw_pcie_wait_for_link() (Joao Pinto)
- Add default link up check if sub-driver doesn't override (Joao Pinto)
- Add driver for prototyping kits based on ARC SDP (Joao Pinto)
TI Keystone host bridge driver:
- Defer probing if devm_phy_get() returns -EPROBE_DEFER (Shawn Lin)
Xilinx AXI host bridge driver:
- Use of_pci_get_host_bridge_resources() to parse DT (Bharat Kumar Gogada)
- Remove dependency on ARM-specific struct hw_pci (Bharat Kumar Gogada)
- Don't call pci_fixup_irqs() on Microblaze (Bharat Kumar Gogada)
- Update Zynq binding with Microblaze node (Bharat Kumar Gogada)
- microblaze: Support generic Xilinx AXI PCIe Host Bridge IP driver (Bharat Kumar Gogada)
Xilinx NWL host bridge driver:
- Add support for Xilinx NWL PCIe Host Controller (Bharat Kumar Gogada)
Miscellaneous:
- Check device_attach() return value always (Bjorn Helgaas)
- Move pci_set_flags() from asm-generic/pci-bridge.h to linux/pci.h (Bjorn Helgaas)
- Remove includes of empty asm-generic/pci-bridge.h (Bjorn Helgaas)
- ARM64: Remove generated include of asm-generic/pci-bridge.h (Bjorn Helgaas)
- Remove empty asm-generic/pci-bridge.h (Bjorn Helgaas)
- Remove includes of asm/pci-bridge.h (Bjorn Helgaas)
- Consolidate PCI DMA constants and interfaces in linux/pci-dma-compat.h (Bjorn Helgaas)
- unicore32: Remove unused HAVE_ARCH_PCI_SET_DMA_MASK definition (Bjorn Helgaas)
- Cleanup pci/pcie/Kconfig whitespace (Andreas Ziegler)
- Include pci/hotplug Kconfig directly from pci/Kconfig (Bjorn Helgaas)
- Include pci/pcie/Kconfig directly from pci/Kconfig (Bogicevic Sasa)
- frv: Remove stray pci_{alloc,free}_consistent() declaration (Christoph Hellwig)
- Move pci_dma_* helpers to common code (Christoph Hellwig)
- Add PCI_CLASS_SERIAL_USB_DEVICE definition (Heikki Krogerus)
- Add QEMU top-level IDs for (sub)vendor & device (Robin H. Johnson)
- Fix broken URL for Dell biosdevname (Naga Venkata Sai Indubhaskar Jupudi)"
* tag 'pci-v4.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits)
PCI: Add PCI_CLASS_SERIAL_USB_DEVICE definition
PCI: designware: Add driver for prototyping kits based on ARC SDP
PCI: designware: Add default link up check if sub-driver doesn't override
PCI: designware: Add generic dw_pcie_wait_for_link()
PCI: Cleanup pci/pcie/Kconfig whitespace
PCI: Simplify pci_create_attr() control flow
PCI: Don't leak memory if sysfs_create_bin_file() fails
PCI: Simplify sysfs ROM cleanup
PCI: Remove unused IORESOURCE_ROM_COPY and IORESOURCE_ROM_BIOS_COPY
MIPS: Loongson 3: Keep CPU physical (not virtual) addresses in shadow ROM resource
MIPS: Loongson 3: Use temporary struct resource * to avoid repetition
ia64/PCI: Keep CPU physical (not virtual) addresses in shadow ROM resource
ia64/PCI: Use ioremap() instead of open-coded equivalent
ia64/PCI: Use temporary struct resource * to avoid repetition
PCI: Clean up pci_map_rom() whitespace
PCI: Remove arch-specific IORESOURCE_ROM_SHADOW size from sysfs
PCI: thunder: Add driver for ThunderX-pass{1,2} on-chip devices
PCI: thunder: Add PCIe host driver for ThunderX processors
PCI: generic: Expose pci_host_common_probe() for use by other drivers
PCI: generic: Add pci_host_common_probe(), based on gen_pci_probe()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
- Add the CPU id for the new z13s machine
- Add a s390 specific XOR template for RAID-5 checksumming based on the
XC instruction. Remove all other alternatives, XC is always faster
- The merge of our four different stack tracers into a single one
- Tidy up the code related to page tables, several large inline
functions are now out-of-line. Bloat-o-meter reports ~11K text size
reduction
- A binary interface for the priviledged CLP instruction to retrieve
the hardware view of the installed PCI functions
- Improvements for the dasd format code
- Bug fixes and cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (31 commits)
s390/pci: enforce fmb page boundary rule
s390: fix floating pointer register corruption (again)
s390/cpumf: add missing lpp magic initialization
s390: Fix misspellings in comments
s390/mm: split arch/s390/mm/pgtable.c
s390/mm: uninline pmdp_xxx functions from pgtable.h
s390/mm: uninline ptep_xxx functions from pgtable.h
s390/pci: add ioctl interface for CLP
s390: Use pr_warn instead of pr_warning
s390/dasd: remove casts to dasd_*_private
s390/dasd: Refactor dasd format functions
s390/dasd: Simplify code in format logic
s390/dasd: Improve dasd format code
s390/percpu: remove this_cpu_cmpxchg_double_4
s390/cpumf: Improve guest detection heuristics
s390/fault: merge report_user_fault implementations
s390/dis: use correct escape sequence for '%' character
s390/kvm: simplify set_guest_storage_key
s390/oprofile: add z13/z13s model numbers
s390: add z13s model number to z13 elf platform
...
|
|
* pci/resource:
PCI: Simplify pci_create_attr() control flow
PCI: Don't leak memory if sysfs_create_bin_file() fails
PCI: Simplify sysfs ROM cleanup
PCI: Remove unused IORESOURCE_ROM_COPY and IORESOURCE_ROM_BIOS_COPY
MIPS: Loongson 3: Keep CPU physical (not virtual) addresses in shadow ROM resource
MIPS: Loongson 3: Use temporary struct resource * to avoid repetition
ia64/PCI: Keep CPU physical (not virtual) addresses in shadow ROM resource
ia64/PCI: Use ioremap() instead of open-coded equivalent
ia64/PCI: Use temporary struct resource * to avoid repetition
PCI: Clean up pci_map_rom() whitespace
PCI: Remove arch-specific IORESOURCE_ROM_SHADOW size from sysfs
PCI: Set ROM shadow location in arch code, not in PCI core
PCI: Don't enable/disable ROM BAR if we're using a RAM shadow copy
PCI: Don't assign or reassign immutable resources
PCI: Mark shadow copy of VGA ROM as IORESOURCE_PCI_FIXED
x86/PCI: Mark Broadwell-EP Home Agent & PCU as having non-compliant BARs
PCI: Disable IO/MEM decoding for devices with non-compliant BARs
|
|
* pci/host-hv:
PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs
PCI: Look up IRQ domain by fwnode_handle
PCI: Add fwnode_handle to x86 pci_sysdata
|
|
* pci/host-designware:
PCI: designware: Add driver for prototyping kits based on ARC SDP
PCI: designware: Add default link up check if sub-driver doesn't override
PCI: designware: Add generic dw_pcie_wait_for_link()
ARC: Add PCI support
|
|
'pci/host-rcar', 'pci/host-tegra', 'pci/host-thunder', 'pci/host-vmd', 'pci/host-xilinx' and 'pci/host-xilinx-nwl' into next
* pci/host-altera:
PCI: altera: Fix altera_pcie_link_is_up()
* pci/host-imx6:
PCI: imx6: Add DT bindings to configure PHY Tx driver settings
* pci/host-keystone:
PCI: keystone: Defer probing if devm_phy_get() returns -EPROBE_DEFER
* pci/host-rcar:
PCI: rcar: Depend on ARCH_RENESAS, not ARCH_SHMOBILE
* pci/host-tegra:
PCI: tegra: Remove misleading PHYS_OFFSET
PCI: tegra: Track bus -> CPU mapping
PCI: tegra: Remove unused struct tegra_pcie.num_ports field
PCI: tegra: Implement ->{add,remove}_bus() callbacks
PCI: Add pci_ops.{add,remove}_bus() callbacks
* pci/host-thunder:
PCI: thunder: Add driver for ThunderX-pass{1,2} on-chip devices
PCI: thunder: Add PCIe host driver for ThunderX processors
PCI: generic: Expose pci_host_common_probe() for use by other drivers
PCI: generic: Add pci_host_common_probe(), based on gen_pci_probe()
PCI: generic: Move structure definitions to separate header file
* pci/host-vmd:
x86/PCI: VMD: Attach VMD resources to parent domain's resource tree
x86/PCI: VMD: Set bus resource start to 0
x86/PCI: VMD: Document code for maintainability
* pci/host-xilinx:
microblaze/PCI: Support generic Xilinx AXI PCIe Host Bridge IP driver
PCI: xilinx: Update Zynq binding with Microblaze node
PCI: xilinx: Don't call pci_fixup_irqs() on Microblaze
PCI: xilinx: Remove dependency on ARM-specific struct hw_pci
PCI: xilinx: Use of_pci_get_host_bridge_resources() to parse DT
* pci/host-xilinx-nwl:
PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller
|
|
'pci/virtualization' and 'pci/vpd' into next
* pci/aer:
PCI/AER: Log aer_inject error injections
PCI/AER: Log actual error causes in aer_inject
PCI/AER: Use dev_warn() in aer_inject
PCI/AER: Fix aer_inject error codes
* pci/enumeration:
PCI: Fix broken URL for Dell biosdevname
* pci/kconfig:
PCI: Cleanup pci/pcie/Kconfig whitespace
PCI: Include pci/hotplug Kconfig directly from pci/Kconfig
PCI: Include pci/pcie/Kconfig directly from pci/Kconfig
* pci/misc:
PCI: Add PCI_CLASS_SERIAL_USB_DEVICE definition
PCI: Add QEMU top-level IDs for (sub)vendor & device
unicore32: Remove unused HAVE_ARCH_PCI_SET_DMA_MASK definition
PCI: Consolidate PCI DMA constants and interfaces in linux/pci-dma-compat.h
PCI: Move pci_dma_* helpers to common code
frv/PCI: Remove stray pci_{alloc,free}_consistent() declaration
* pci/virtualization:
PCI: Wait for up to 1000ms after FLR reset
PCI: Support SR-IOV on any function type
* pci/vpd:
PCI: Prevent VPD access for buggy devices
PCI: Sleep rather than busy-wait for VPD access completion
PCI: Fold struct pci_vpd_pci22 into struct pci_vpd
PCI: Rename VPD symbols to remove unnecessary "pci22"
PCI: Remove struct pci_vpd_ops.release function pointer
PCI: Move pci_vpd_release() from header file to pci/access.c
PCI: Move pci_read_vpd() and pci_write_vpd() close to other VPD code
PCI: Determine actual VPD size on first access
PCI: Use bitfield instead of bool for struct pci_vpd_pci22.busy
PCI: Allow access to VPD attributes with size 0
PCI: Update VPD definitions
|
|
PCI-SIG has defined Interface FEh for Base Class 0Ch, Sub-Class 03h as "USB
Device (not host controller)". It is already being used in various USB
device controller drivers for matching, so add PCI_CLASS_SERIAL_USB_DEVICE
and use it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
