| Age | Commit message (Collapse) | Author |
|---|
|
If the console is a PCI device, and we try to print to it while its
decoding is disabled, the system will hang. This particular printk hasn't
caused a problem yet, but it could, so this fixes it.
See also 0ff9514b579b ("PCI: Don't print anything while decoding is
disabled").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If a BAR is above 4GB and our dma_addr_t is too small, don't clear the BAR
to zero: that doesn't disable the BAR, and it makes it more likely that the
BAR will conflict with things if we turn on the memory enable bit (as we
will at "out:" if the device was already enabled at the handoff).
We should also print the BAR info and its original size so we can follow
the process when we try to assign space to it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If dma_addr_t is too small to represent the BAR value,
pcibios_bus_to_resource() will fail, so just remember the BAR size directly
in the resource. The resource is already marked UNSET, so we know the
address isn't valid anyway.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We can only handle BARs above 4GB if dma_addr_t (not resource_size_t) is 64
bits wide. If we have a 64-bit resource_size_t and a 32-bit dma_addr_t,
we can't deal with BARs above 4GB.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We can only handle BARs larger than 4GB if both dma_addr_t and
resource_size_t are 64 bits wide. If dma_addr_t is 32 bits, we can't
represent all the bus addresses, and if resource_size_t is 32 bits, we
can't represent all the CPU addresses.
Previously we cleared res->flags (at "fail:") for resources that were too
large. That means we think the BAR doesn't exist at all, which in turn
means that we could enable the device even though we can't keep track of
where the BAR is and we can't make sure it doesn't overlap something else.
This preserves the type flags (MEM/IO) so we can keep from enabling the
device.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove pcibios_add_platform_entries(). Architecture-specific attributes
can be achieved by setting pdev->dev.groups.
Link: https://lkml.kernel.org/r/alpine.LFD.2.11.1404141101500.1529@denkbrett
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for an SHPCHP hotplug regression, a "wait for pending
transaction" problem (used in device reset paths), and an email
address update.
PCI device hotplug:
- Fix SHPCHP bus speed mismatch issue (Marcel Apfelbaum)
Miscellaneous:
- Fix pci_wait_for_pending_transaction() (Gavin Shan)
- Update email address (Ben Hutchings)"
* tag 'pci-v3.15-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Wrong register used to check pending traffic
PCI: shpchp: Check bridge's secondary (not primary) bus speed
PCI: Update my email address
|
|
INTx masking does not work on this device. To see this, configure the
network device UP on an active network, note that the interrupt count
continues to increment for the device in /proc/interrupts. Use setpci to
set the PCI_COMMAND_INTX_DISABLE bit in the PCI_COMMAND register. As
expected, the interrupt count ceases to increment. However, reading the
PCI_STATUS_INTERRUPT bit of the PCI_STATUS register does not indicate that
interrupts are pending and clearing PCI_COMMAND_INTX_DISABLE in the
PCI_COMMAND register does not allow the device to continue operation.
This does not affect operation of the host r8169 driver, but it does
prevent the device from being functional when assigned to a VM, such as
with QEMU and VFIO. The guest driver successfully probes the device, but
there is no traffic. Mark INTx masking as broken, allowing the more
restrictive APIC masking to be used instead.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The incorrect register offset is passed to pci_wait_for_pending(), which is
caused by commit 157e876ffe ("PCI: Add pci_wait_for_pending() (refactor
pci_wait_for_pending_transaction())").
Fixes: 157e876ffe ("PCI: Add pci_wait_for_pending() (refactor pci_wait_for_pending_transaction())
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@gmail.com>
CC: stable@vger.kernel.org # v3.14+
|
|
No functional change, just cleaned up a bit.
This does not replace the requirement to move x86 to irq domains, but
it limits the mess to some degree.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: x86@kernel.org
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20140507154335.452206351@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When a new device is added below a hotplug bridge, the bridge's secondary
bus speed and the device's bus speed must match. The shpchp driver
previously checked the bridge's *primary* bus speed, not the secondary bus
speed.
This caused hot-add errors like:
shpchp 0000:00:03.0: Speed of bus ff and adapter 0 mismatch
Check the secondary bus speed instead.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=75251
Fixes: 3749c51ac6c1 ("PCI: Make current and maximum bus speeds part of the PCI core")
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
CC: stable@vger.kernel.org # v2.6.34+
|
|
change made to resolve following checkpatch message:
drivers/pci/pci.c:109: ERROR: "foo* bar" should be "foo *bar"
branch: Linux 3.14-rc8
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
into fixes
From Jason Cooper:
mvebu drivers (mbus and pci) fixes for v3.15
- pci
- fix off-by-one for mbus window size
- split BARs into multiple mbus windows when needed
- mbus
- avoid setting undefined window size
- allow several windows with the same target/attr
* tag 'mvebu-mbus_pci-fixes-3.15' of git://git.infradead.org/linux-mvebu:
PCI: mvebu: split PCIe BARs into multiple MBus windows when needed
bus: mvebu-mbus: allow several windows with the same target/attribute
bus: mvebu-mbus: Avoid setting an undefined window size
PCI: mvebu: fix off-by-one in the computed size of the mbus windows
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
There are no users of pci_enable_msi_block() function left. Obsolete it in
favor of pci_enable_msi_range() and pci_enable_msi_exact() functions.
Previously, we called arch_setup_msi_irqs() once, requesting the same
vector count we passed to arch_msi_check_device(). Now we may call it
several times: if it returns failure, we may retry and request fewer
vectors.
We don't keep track of the vector count we initially passed to
arch_msi_check_device(). We only keep track of the number of vectors
successfully set up by arch_setup_msi_irqs(), and this is what we use to
clean things up when disabling MSI. Therefore, we assume that
arch_msi_check_device() does nothing that will have to be cleaned up later.
[bhelgaas: changelog]
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move the devspec OF attribute to PCI common code's set of device attributes
since it's not architecture dependent. As a side effect microblaze and
powerpc no longer need to use pcibios_add_platform_entries().
[bhelgaas: fold in #include for compile error]
Link: https://lkml.kernel.org/r/alpine.LFD.2.11.1404141101500.1529@denkbrett
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
into next
* pci/hotplug:
PCI: rphahp: Fix endianess issues
PCI: Allow hotplug service drivers to operate in polling mode
PCI: pciehp: Acknowledge spurious "cmd completed" event
PCI: pciehp: Use PCI_EXP_SLTCAP_PSN define
PCI: hotplug: Remove unnecessary "dev->bus" test
* pci/msi:
GenWQE: Use pci_enable_msi_exact() instead of pci_enable_msi_block()
PCI/MSI: Simplify populate_msi_sysfs()
PCI/portdrv: Use pci_enable_msix_exact() instead of pci_enable_msix()
* pci/virtualization:
PCI: Add Patsburg (X79) to Intel PCH root port ACS quirk
* pci/misc:
PCI: Fix use of uninitialized MPS value
PCI: Remove dead code
MAINTAINERS: Add arch/x86/kernel/quirks.c to PCI file patterns
PCI: Remove unnecessary __ref annotations
PCI: Fail new_id for vendor/device values already built into driver
PCI: Add new ID for Intel GPU "spurious interrupt" quirk
PCI: Update my email address
PCI: Fix incorrect vgaarb conditional in WARN_ON()
PCI: Use designated initialization in PCI_VDEVICE
PCI: Remove old serial device IDs
PCI: Remove unnecessary includes of <linux/init.h>
powerpc/PCI: Fix NULL dereference in sys_pciconfig_iobase() list traversal
|
|
If "pcie_bus_config == PCIE_BUS_PERFORMANCE", we don't initialize "smpss",
so we pass a pointer to garbage into pcie_bus_configure_set(), where we
compute "mps" based on the garbage. We then pass the garbage "mps" to
pcie_write_mps(), which ignores it in the PCIE_BUS_PERFORMANCE case.
Coverity isn't smart enough to deduce that we ignore the garbage (it's a
lot to expect from a human, too), so initialize "smpss" to a safe value in
all cases.
Found by Coverity (CID 146454).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
"pdev" can never be NULL here, so remove the test.
Found by Coverity (CID 744313).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Some PCI functions used to be marked __devinit. When CONFIG_HOTPLUG was
not set, these functions were discarded after boot. A few callers of these
__devinit functions were marked __ref to indicate that they could safely
call the __devinit functions even though the callers were not __devinit.
But CONFIG_HOTPLUG and __devinit are now gone, and the need for the __ref
annotations is also gone, so remove them. Relevant historical commits:
54b956b90360 Remove __dev* markings from init.h
a8e4b9c101ae PCI: add generic pci_hp_add_bridge()
0ab2b57f8db8 PCI: fix section mismatch warning in pci_scan_child_bus
451124a7cc6c PCI: fix 4x section mismatch warnings
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
While using the sysfs new_id interface, the user can unintentionally feed
incorrect values if the driver static table has a matching entry. This is
possible since only the device and vendor fields are mandatory and the rest
are optional. As a result, store_new_id() will fill in default values that
are then passed on to the driver and can have unintended consequences.
As an example, consider the ixgbe driver and the 82599EB network card:
echo "8086 10fb" > /sys/bus/pci/drivers/ixgbe/new_id
This will pass a pci_device_id with driver_data = 0 to ixgbe_probe(), which
uses that zero to index a table of card operations. The zeroth entry of
the table does *not* correspond to the 82599 operations.
This change returns an error if the user attempts to add a dynid for a
vendor/device combination for which a static entry already exists.
However, if the user intentionally wants a different set of values, she
must provide all the 7 fields and that will be accepted.
[bhelgaas: drop KVM text since the problem isn't KVM-specific]
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Fix the following build warning that happens when building
multi_v7_defconfig with CONFIG_ARM_LPAE=y:
drivers/pci/host/pci-mvebu.c:334:5: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'phys_addr_t' [-Wformat=]
Fix the warning by using '%pa' to printing 'phys_addr_t' type. While at
it, also use the more standard notation [mem 0x-0x] for memory region.
[bhelgaas: make end address inclusive, remove extra spaces]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
|
|
Serialization of configuration accesses is provided by 'pci_lock' in
drivers/pci/access.c thus making the driver's 'conf_lock' superfluous.
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
|
|
After a CPU upgrade while keeping the same mainboard, we faced "spurious
interrupt" problems again.
It turned out that the new CPU also featured a new GPU with a different PCI
ID.
Add this PCI ID to the quirk table. Probably all other Intel GPU PCI IDs
are affected, too, but I don't want to add them without a test system.
See f67fd55fa96f ("PCI: Add quirk for still enabled interrupts on Intel
Sandy Bridge GPUs") for some history.
[bhelgaas: add f67fd55fa96f reference, stable tag]
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.4+
|
|
The problem was initially reported by Wendy who tried pass through
IPR adapter, which was connected to PHB root port directly, to KVM
based guest. When doing that, pci_reset_bridge_secondary_bus() was
called by VFIO driver and linkDown was detected by the root port.
That caused all PEs to be frozen.
The patch fixes the issue by routing the reset for the secondary bus
of root port to underly firmware. For that, one more weak function
pci_reset_secondary_bus() is introduced so that the individual platforms
can override that and do specific reset for bridge's secondary bus.
Reported-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Numerical values stored in the device tree are encoded in Big Endian and
should be byte swapped when running in Little Endian.
The RPA hotplug module should convert those values as well.
Note that in rpaphp_get_drc_props(), the comparison between indexes[i+1]
and *index is done using the BE values (whatever is the current endianess).
This doesn't matter since we are checking for equality here. This way only
the returned value is byte swapped.
RPA also made RTAS calls which implies BE values to be used. According to
the patch done in RTAS (http://patchwork.ozlabs.org/patch/336865), no
additional conversion is required in RPA.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
3448a19da479 "vgaarb: use bridges to control VGA routing where possible"
added the "flags & PCI_VGA_STATE_CHANGE_DECODES" condition to an existing
WARN_ON(), but used bitwise AND (&) instead of logical AND (&&), so the
condition is never true. Replace with logical AND.
Found by Coverity (CID 142811).
Fixes: 3448a19da479 "vgaarb: use bridges to control VGA routing where possible"
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Airlie <airlied@redhat.com>
|
|
Today the PCIe port bus driver disables the Hot-plug service if the port
device does not have the capability to generate interrupts. However, a
user must be able to use the "pciehp_poll_mode" parameter to use the pciehp
in polling method in such a case. Today it is not possible.
This patch allows a hotplug service driver to decide whether or not it
would like to continue in the absence of interrupts.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
In case of a spurious "cmd completed", pcie_write_cmd() does not clear it,
but yet expects more "cmd completed" events to be generated. This does not
happen because the previous (spurious) event has not been acknowledged.
Fix that.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
MBus windows are used on Marvell platforms to map certain peripherals
in the physical address space. In the PCIe context, MBus windows are
needed to map PCIe I/O and memory regions in the physical address.
However, those MBus windows can only have power of two sizes, while
PCIe BAR do not necessarily guarantee this. For this reason, the
current pci-mvebu breaks on platforms where PCIe devices have BARs
that don't sum up to a power of two size at the emulated bridge level.
This commit fixes this by allowing the pci-mvebu driver to create
multiple contiguous MBus windows (each having a power of two size) to
cover a given PCIe BAR.
To achieve this, two functions are added: mvebu_pcie_add_windows() and
mvebu_pcie_del_windows() to respectively add and remove all the MBus
windows that are needed to map the provided PCIe region base and
size. The emulated PCI bridge code now calls those functions, instead
of directly calling the mvebu-mbus driver functions.
Fixes: 45361a4fe446 ('pci: PCIe driver for Marvell Armada 370/XP systems')
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397823593-1932-8-git-send-email-thomas.petazzoni@free-electrons.com
Tested-by: Neil Greatorex <neil@fatboyfat.co.uk>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
mvebu_pcie_handle_membase_change() and
mvebu_pcie_handle_iobase_change() do not correctly compute the window
size. PCI uses an inclusive start/end address pair, which requires a
+1 when converting to size.
This only worked because a bug in the mbus driver allowed it to
silently accept and round up bogus sizes.
Fix this by adding one to the computed size.
Fixes: 45361a4fe446 ('PCIe driver for Marvell Armada 370/XP systems')
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Willy Tarreau <w@1wt.eu>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397823593-1932-5-git-send-email-thomas.petazzoni@free-electrons.com
Tested-by: Neil Greatorex <neil@fatboyfat.co.uk>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Mostly scripted conversion of the smp_mb__* barriers.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/n/tip-55dhyhocezdw1dg7u19hmh1u@git.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This allows interrupts to be remapped across bridges.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This allows interrupts to be remapped across bridges.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This makes INTB, INTC, and INTD work on i.MX.
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
|
|
This patch corrects iATU programming for cfg1, io and mem viewport. Enable
ATU only after configuring it.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Ajay Khandelwal <ajay.khandelwal@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: stable@vger.kernel.org
|
|
Corrects comment for setting number of lanes.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
|
|
Serialization of configuration accesses is provided by 'pci_lock' in
drivers/pci/access.c thus making the driver's 'conf_lock' superfluous.
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Richard Zhu <r65037@freescale.com>
|
|
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This makes INTB, INTC, and INTD work on i.MX.
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
|
|
This patch corrects iATU programming for cfg1, io and mem viewport. Enable
ATU only after configuring it.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Ajay Khandelwal <ajay.khandelwal@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: stable@vger.kernel.org
|
|
Corrects comment for setting number of lanes.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
|
|
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This allows interrupts to be remapped across bridges.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Intel has updated Red Hat bz1037684 to note that X79 PCH root ports also
provide isolation and the same ACS quirks apply. Some sources indicate
additional device IDs for X79, but this patch includes only the ones
specifically identified by Intel:
https://bugzilla.redhat.com/show_bug.cgi?id=1037684#c11
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Don Dugger <donald.d.dugger@intel.com>
|
|
None of these files are actually using any __init type directives and hence
don't need to include <linux/init.h>. Most are just a left over from
__devinit and __cpuinit removal, or simply due to code getting copied from
one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use PCI_EXP_SLTCAP_PSN to make it easier to find code that uses the
Physical Slot Number field in the PCIe Slot Capabilities register.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Every pci_dev is on a valid pci_bus, so we don't need to test whether
dev->bus is NULL or not.
The only exceptions are a few legacy cases like alpha_core_agp_setup(),
parisc_agp_setup(), and megaraid's make_local_pdev(), where we allocate a
pci_dev with a NULL bus pointer. These are dubious uses (especially the
megaraid one), and I don't think it's possible to exercise this
pci_configure_slot() path with any of them.
Found by Coverity (CID 146446).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Simplify populate_msi_sysfs() by
- Swapping the order of the two allocations and storing the
msi_dev_attr-derived pointer right after allocation, allowing the
cleanup code to pick things up without extra effort.
- Using kasprintf() instead of the kmalloc()/sprintf() pair.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers using these two
interfaces need to be updated to use the new pci_enable_msi_range() or
pci_enable_msi_exact() and pci_enable_msix_range() or
pci_enable_msix_exact() interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This allows interrupts to be remapped across bridges.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Nothing major: the stricter permissions checking for sysfs broke a
staging driver; fix included. Greg KH said he'd take the patch but
hadn't as the merge window opened, so it's included here to avoid
breaking build"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
staging: fix up speakup kobject mode
Use 'E' instead of 'X' for unsigned module taint flag.
VERIFY_OCTAL_PERMISSIONS: stricter checking for sysfs perms.
kallsyms: fix percpu vars on x86-64 with relocation.
kallsyms: generalize address range checking
module: LLVMLinux: Remove unused function warning from __param_check macro
Fix: module signature vs tracepoints: add new TAINT_UNSIGNED_MODULE
module: remove MODULE_GENERIC_TABLE
module: allow multiple calls to MODULE_DEVICE_TABLE() per module
module: use pr_cont
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 old platform removal from Peter Anvin:
"This patchset removes support for several completely obsolete
platforms, where the maintainers either have completely vanished or
acked the removal. For some of them it is questionable if there even
exists functional specimens of the hardware"
Geert Uytterhoeven apparently thought this was a April Fool's pull request ;)
* 'x86-nuke-platforms-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, platforms: Remove NUMAQ
x86, platforms: Remove SGI Visual Workstation
x86, apic: Remove support for IBM Summit/EXA chipset
x86, apic: Remove support for ia32-based Unisys ES7000
|
