| Age | Commit message (Collapse) | Author |
|---|
|
Near the top of the function, spi_imx->controller is set to
controller (and is of course never modified again). The rest of the
function uses a mix of the two expressions.
For consistency, readability and better code generation, drop all the
spi_imx-> indirections.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230425134527.483607-2-linux@rasmusvillemoes.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the missing kernel documentation to silence the build warning.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230523090124.3132-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When working in slave mode it seems the timing is exceedingly tight.
The TX FIFO can never empty, because the master is driving the clock so
zeros would be sent for those bytes where the FIFO is empty.
Return to interleaving the writing of the TX FIFO and the reading
of the RX FIFO to try to ensure the data is available when required.
Fixes: a84c11e16dc2 ("spi: spi-cadence: Avoid read of RX FIFO before its ready")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230518093927.711358-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The function debugfs_create_dir returns ERR_PTR if an error occurs,
and the appropriate way to verify for errors is to use the inline
function IS_ERR. The patch will substitute the null-comparison with
IS_ERR.
Suggested-by: Ivan Orlov <ivan.orlov0322@gmail.com
Signed-off-by: Yeqi Fu <asuk4.q@gmail.com
Link: https://lore.kernel.org/r/20230518052515.368978-1-asuk4.q@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
The AMD Pensando Elba SoC has the Cadence QSPI controller integrated.
The quirk CQSPI_NEEDS_APB_AHB_HAZARD_WAR is added and if enabled
a dummy readback from the controller is performed to ensure
synchronization.
Signed-off-by: Brad Larson <blarson@amd.com
Link: https://lore.kernel.org/r/20230515181606.65953-8-blarson@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
New set/get APIs for accessing spi->chip_select were introduced by
'commit 9e264f3f85a5 ("spi: Replace all spi->chip_select and spi->cs_gpiod
references with function call")', but the 'commit 2c8606040a80 ("spi: dw:
Add support for AMD Pensando Elba SoC")' uses the old interface by directly
accessing spi->chip_select. So, replace all spi->chip_select references
in the driver with new get/set APIs.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com
Acked-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230515130343.63770-1-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
n_bytes variable in the driver represents the number of bytes per word
that needs to be sent/copied to fifo. Bits/word can be between 8 and 32
bits from the client but in memory they are a power of 2, same is mentioned
in spi.h header:
"
* @bits_per_word: Data transfers involve one or more words; word sizes
* like eight or 12 bits are common. In-memory wordsizes are
* powers of two bytes (e.g. 20 bit samples use 32 bits).
* This may be changed by the device's driver, or left at the
* default (0) indicating protocol words are eight bit bytes.
* The spi_transfer.bits_per_word can override this for each transfer.
"
Hence, round of n_bytes to a power of 2 to avoid values like 3 which
would generate unalligned/odd accesses to memory/fifo.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Fixes: a51acc2400d4 ("spi: dw: Add support for 32-bits max xfer size")
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com
Signed-off-by: Joy Chakraborty <joychakr@google.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com
Tested-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230512104746.1797865-4-joychakr@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Store address width capabilities of DMA controller during init and check
the same per transfer to make sure the bits/word requirement can be met.
Current DW DMA driver requires both tx and rx channel to be configured
and functional hence a subset of both tx and rx channel address width
capability is checked with the width requirement(n_bytes) for a
transfer.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Signed-off-by: Joy Chakraborty <joychakr@google.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com
Tested-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230512104746.1797865-3-joychakr@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Check capabilities of DMA controller during init to make sure it is
capable of handling MEM2DEV for tx channel, DEV2MEM for rx channel.
Current DW DMA driver requires both tx and rx channel to be configured
and functional for any kind of transfers to take effect including
half duplex. Hence, check for both tx and rx direction and fail on
unavailbility of either.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Signed-off-by: Joy Chakraborty <joychakr@google.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com
Tested-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230512104746.1797865-2-joychakr@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Commit b1b90514eaa3 ("spi: spi-cadence: Add support for Slave mode")
updated the code to trigger the IRQ when the FIFO was half empty,
overlapping filling more data into the FIFO and sending what is left.
This appears to cause regressions on the Zynq 7000, for transactions
longer than the FIFO size, below that no overlapping occurs.
It would appear from my testing that any attempt to put new data into
the FIFO whilst data is still transmitting causes data corruption
on both send and receive. If I am reading the commit message right
on commit 49530e641178 ("spi: cadence: Add usleep_range() for
cdns_spi_fill_tx_fifo()"), that would also seem to imply this is the
case.
On the assumption that this isn't an issue on the platform
the original slave mode support was added for, update the
cdns_transfer_one to only set the watermark to 50% of the FIFO size
when in slave mode. There by retaining the new behaviour for slave
mode but reverting to the older behaviour when the SPI is used a
master.
Fixes: b1b90514eaa3 ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230509164153.3907694-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Recent changes to cdns_spi_irq introduced some issues.
Firstly, when writing the end of a longer transaction, the code in
cdns_spi_irq will write data into the TX FIFO, then immediately
fall into the if (!xspi->tx_bytes) path and attempt to read data
from the RX FIFO. However this required waiting for the TX FIFO to
empty before the RX data was ready.
Secondly, the variable trans_cnt is now rather inaccurately named
since in cases, where the watermark is set to 1, trans_cnt will be
1 but the count of bytes transferred would be much longer.
Finally, when setting up the transaction we set the watermark to 50%
of the FIFO if the transaction is great than 50% of the FIFO. However,
there is no need to split a tranaction that is smaller than the
whole FIFO, so anything up to the FIFO size can be done in a single
transaction.
Tidy up the code a little, to avoid repeatedly calling
cdns_spi_read_rx_fifo with a count of 1, and correct the three issues
noted above.
Fixes: b1b90514eaa3 ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230509164153.3907694-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
These SoCs has two SPI controllers. One of it is quite similar to previous
ones, but with internal clock divider removed; the other added MIPI DBI
Type-C offload based on the first one.
Add basical support for these controllers. As we're not going to
support the DBI functionality now, just implement the two kinds of
controllers as the same.
Co-developed-by: Icenowy Zheng <icenowy@aosc.io
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com
Reviewed-by: Andre Przywara <andre.przywara@arm.com
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com
Link: https://lore.kernel.org/r/20230510081121.3463710-5-bigunclemax@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Previously SPI controllers in Allwinner SoCs has a clock divider inside.
However now the clock divider is removed and to set the transfer clock
rate it's only needed to set the SPI module clock to the target value
and configure a proper work mode.
According to the datasheet there are three work modes:
| SPI Sample Mode | SDM(bit13) | SDC(bit11) | Run Clock |
|-------------------------|------------|------------|-----------|
| normal sample | 1 | 0 | <= 24 MHz |
| delay half cycle sample | 0 | 0 | <= 40 MHz |
| delay one cycle sample | 0 | 1 | >= 80 MHz |
Add a quirk for this kind of SPI controllers.
Co-developed-by: Icenowy Zheng <icenowy@aosc.io
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com
Reviewed-by: Andre Przywara <andre.przywara@arm.com
Link: https://lore.kernel.org/r/20230510081121.3463710-4-bigunclemax@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
As we're adding more properties to the OF match data, convert it to a
struct now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com
Reviewed-by: Samuel Holland <samuel@sholland.org
Reviewed-by: Andre Przywara <andre.przywara@arm.com
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com
Link: https://lore.kernel.org/r/20230510081121.3463710-3-bigunclemax@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Fixing the problem of enabling DMA mode and IRQ mode at the same time.
In this case, a value of more than 6bits is written to RDY_LVL, it can
cause an invasion of other registers, potentially leading to SPI
transfer failure.
Fixes: 1ee806718d5e ("spi: s3c64xx: support interrupt based pio mode")
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Link: https://lore.kernel.org/r/20230510113942.89994-1-jaewon02.kim@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Spi geni driver switches between FIFO and DMA modes based on xfer length.
FIFO mode relies on M_CMD_DONE_EN interrupt for completion while DMA mode
relies on XX_DMA_DONE.
During dynamic switching, if FIFO mode is chosen, FIFO related interrupts
are enabled and DMA related interrupts are disabled. And viceversa.
Chip select shares M_CMD_DONE_EN interrupt with FIFO to check completion.
Now, if a chip select operation is preceded by a DMA xfer, M_CMD_DONE_EN
interrupt would have been disabled and hence it will never receive one
resulting in timeout.
For chip select, in addition to setting the xfer mode to FIFO,
select_mode() to FIFO so that required interrupts are enabled.
Fixes: e5f0dfa78ac7 ("spi: spi-geni-qcom: Add support for SE DMA mode")
Suggested-by: Praveen Talari <quic_ptalari@quicinc.com
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com
Reviewed-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/1683626496-9685-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Merge series from Joy Chakraborty <joychakr@google.com>:
This Patch series adds support for 32 bits per word trasfers using DMA
and some defensive checks around dma controller capabilities.
|
|
Merge series from Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>:
There are large number of QSPI irqs that fire during boot/init and later
on every suspend/resume.
This could be made faster by doing DMA instead of PIO.
Below is comparison for number of interrupts raised in 2 scenarios...
Boot up and stabilise
Suspend/Resume
Sequence PIO DMA
=======================
Boot-up 69088 19284
S/R 5066 3430
Speed test results...
spi-nor read times in sec after 2 min uptime
============================================
PIO - Iterations-1000, min=3.18, max=3.74, avg=3.53
DMA - Iterations-1000, min=1.21, max=2.28, avg=1.79
spi-nor write times in sec after 2 min uptime
=============================================
PIO - Iterations-1000, min=3.20, max=8.24, avg=3.58
DMA - Iterations-1000, min=1.25, max=5.13, avg=1.82
Further testing performed...
a) multiple entries in sgt (simulated by max_dma_len = 1024)
b) fallback to pio (simulated by dma setup failure)
|
|
Merge series from Jaewon Kim <jaewon02.kim@samsung.com>:
Previously, polling mode was supported as quirk for SOC without DMA.
In order to use it more flexibly, it is supported when there is
no dmas property in devicetree, and the issue of using excessive CPU
usage in polling mode is solved by adding sleep during transfer time and
supporting interrupt mode.
Changes in V3.
- Fix patch commit message.
- Change of_find_property() to of_property_present() with code cleanup
- Remove cpu_relax() related patch.
- Changes use_irq variable type to bool
Changes in V2.
- Switched to polling mode if there is no dmas property in devicetree.
- Add cpu_releax() in polling loop
- Add lower limit in IRQ mode
Jaewon Kim (3):
spi: s3c64xx: change polling mode to optional
spi: s3c64xx: add sleep during transfer
spi: s3c64xx: support interrupt based pio mode
drivers/spi/spi-s3c64xx.c | 81 +++++++++++++++++++----
include/linux/platform_data/spi-s3c64xx.h | 1 +
2 files changed, 70 insertions(+), 12 deletions(-)
--
2.17.1
|
|
The CS_TOGGLE bit when set is supposed to instruct FW to
toggle CS line between words. The driver with intent of
disabling this behaviour has been unsetting BIT(0). This has
not caused any trouble so far because the original BIT(1)
is untouched and BIT(0) likely wasn't being used.
Correct this to prevent a potential future bug.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org
Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Reviewed-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/1682412128-1913-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Avoid config.speed_hz is 0 when it is a divisor.
Signed-off-by: Han Xu <han.xu@nxp.com
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com
Link: https://lore.kernel.org/r/20230505064159.3964473-1-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Move dw_spi_can_dma() implementation below dw_spi_dma_convert_width()
for handing compile dependency in future patches.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Signed-off-by: Joy Chakraborty <joychakr@google.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com
Tested-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230427123314.1997152-3-joychakr@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Add Support for AxSize = 4 bytes configuration from dw dma driver if
n_bytes i.e. number of bytes per write to fifo is 4.
Number of bytes written to fifo per write is depended on the bits/word
configuration being used which the DW core driver translates to n_bytes.
Hence, for bits per word values between 17 and 32 n_bytes should be
equal to 4.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Signed-off-by: Joy Chakraborty <joychakr@google.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com
Tested-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230427123314.1997152-2-joychakr@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Support interrupt based pio mode to optimize cpu usage.
When transmitting data size is larget than 32 bytes, operates with
interrupt based pio mode.
By using the FIFORDY INT, an interrupt can be triggered when
the desired size of data has been received. Using this, we can support
interrupt based pio mode.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com
Link: https://lore.kernel.org/r/20230502062813.112434-4-jaewon02.kim@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
In polling mode, the status register is continuously read to check data
transfer completion. It can cause excessive CPU usage.
To reduce this, we can calculate the transfer time and put the sleep during
transfer.
When test on ExynosAuto9 SADK board, throughput remained the same, but
100% CPU utilization decreased to 40%.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Link: https://lore.kernel.org/r/20230502062813.112434-3-jaewon02.kim@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Previously, Polling mode was supported as quirk for SOC without DMA.
To provide more flexible support for polling mode, it changed to polling
mode when the 'dmas' property is not present in the devicetree, rather than
using a quirk.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Link: https://lore.kernel.org/r/20230502062813.112434-2-jaewon02.kim@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Current driver supports only PIO mode.
HW supports DMA, so add DMA mode support to the driver
for better performance for larger xfers.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com
Reviewed-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/1682328761-17517-6-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc drivers updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost
breaks even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (196 commits)
mcb-lpc: Reallocate memory region to avoid memory overlapping
mcb-pci: Reallocate memory region to avoid memory overlapping
mcb: Return actual parsed size when reading chameleon table
kernel/configs: Drop Android config fragments
virt: acrn: Replace obsolete memalign() with posix_memalign()
spmi: Add a check for remove callback when removing a SPMI driver
spmi: fix W=1 kernel-doc warnings
spmi: mtk-pmif: Drop of_match_ptr for ID table
spmi: pmic-arb: Convert to platform remove callback returning void
spmi: mtk-pmif: Convert to platform remove callback returning void
spmi: hisi-spmi-controller: Convert to platform remove callback returning void
w1: gpio: remove unnecessary ENOMEM messages
w1: omap-hdq: remove unnecessary ENOMEM messages
w1: omap-hdq: add SPDX tag
w1: omap-hdq: allow compile testing
w1: matrox: remove unnecessary ENOMEM messages
w1: matrox: use inline over __inline__
w1: matrox: switch from asm to linux header
w1: ds2482: do not use assignment in if condition
w1: ds2482: drop unnecessary header
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly standard release for SPI with the exception of a change to
the API for specifying chip selects done in preparation for supporting
devices with more than one chip select, this required some mechanical
changes throughout the tree which have been cooking in -next happily
for a while.
There's also a new API to allow us to support TPM chips on half duplex
controllers.
Summary:
- Refactoring in preparation for supporting multiple chip selects for
a single device, needed by some flash devices, which required a
change in the SPI device API visible throughout the tree
- Support for hardware assisted interaction with SPI TPMs on half
duplex controllers, implemented on nVidia Tedra210 QuadSPI
- Optimisation for large transfers on fsl-cpm devices
- Cleanups around device property use which fix some sisues with
fwnode
- Use of both void remove() and devm_platform_.*ioremap_resource()
- Support for AMD Pensando Elba, Amlogic A1, Cadence device mode,
Intel MetorLake-S and StarFive J7110 QuadSPI"
* tag 'spi-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (185 commits)
spi: bcm63xx: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: tegra210-quad: Enable TPM wait polling
spi: Add TPM HW flow flag
spi: bcm63xx: remove PM_SLEEP based conditional compilation
spi: cadence-quadspi: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: spi-cadence: Add support for Slave mode
spi: spi-cadence: Switch to spi_controller structure
spi: cadence-quadspi: fix suspend-resume implementations
spi: dw: Add support for AMD Pensando Elba SoC
spi: dw: Add AMD Pensando Elba SoC SPI Controller
spi: cadence-quadspi: Disable the SPI before reconfiguring
spi: cadence-quadspi: Update the read timeout based on the length
spi: spi-loopback-test: Add module param for iteration length
spi: add support for Amlogic A1 SPI Flash Controller
dt-bindings: spi: add Amlogic A1 SPI controller
spi: fsl-spi: No need to check transfer length versus word size
spi: fsl-spi: Change mspi_apply_cpu_mode_quirks() to void
spi: fsl-cpm: Use 16 bit mode for large transfers with even size
spi: fsl-spi: Re-organise transfer bits_per_word adaptation
spi: fsl-spi: Fix CPM/QE mode Litte Endian
...
|
|
Using this macro makes the code more readable.
It also inits the members of dev_pm_ops in the following manner
without us explicitly needing to:
.suspend = bcm63xx_spi_suspend, \
.resume = bcm63xx_spi_resume, \
.freeze = bcm63xx_spi_suspend, \
.thaw = bcm63xx_spi_resume, \
.poweroff = bcm63xx_spi_suspend, \
.restore = bcm63xx_spi_resume
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230424102546.1604484-1-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Krishna Yarlagadda <kyarlagadda@nvidia.com>:
TPM devices may insert wait state on last clock cycle of ADDR phase.
For SPI controllers that support full-duplex transfers, this can be
detected using software by reading the MISO line. For SPI controllers
that only support half-duplex transfers, such as the Tegra QSPI, it is
not possible to detect the wait signal from software. The QSPI
controller in Tegra234 and Tegra241 implement hardware detection of the
wait signal which can be enabled in the controller for TPM devices.
Add a flag for this in the SPI core and implement support in the Tegra
QuadSPI driver.
|
|
Trusted Platform Module requires flow control. As defined in TPM
interface specification, client would drive MISO line at same cycle as
last address bit on MOSI.
Tegra234 and Tegra241 QSPI controllers have TPM wait state detection
feature which is enabled for TPM client devices reported in SPI device
mode bits.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20230421091309.2672-4-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Get rid of conditional compilation based on CONFIG_PM_SLEEP because
it may introduce build issues with certain configs where it maybe disabled
This is because if above config is not enabled the suspend-resume
functions are never part of the code but the bcm63xx_spi_pm_ops struct
still inits them to non-existent suspend-resume functions.
Fixes: b42dfed83d95 ("spi: add Broadcom BCM63xx SPI controller driver")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230420121615.967487-1-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Using this macro makes the code more readable.
It also inits the members of dev_pm_ops in the following manner
without us explicitly needing to:
.suspend = cqspi_suspend, \
.resume = cqspi_resume, \
.freeze = cqspi_suspend, \
.thaw = cqspi_resume, \
.poweroff = cqspi_suspend, \
.restore = cqspi_resume
Also get rid of conditional compilation based on CONFIG_PM_SLEEP because
it introduces build issues with certain configs when CQSPI_DEV_PM_OPS is
just NULL.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304191900.2fARFQW9-lkp@intel.com/
Fixes: 140623410536 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230420054257.925092-1-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"A small fix in the error handling for the rockchip driver, ensuring we
don't leak clock enables if we fail to request the interrupt for the
device"
* tag 'spi-fix-v6.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-rockchip: Fix missing unwind goto in rockchip_sfc_probe()
|
|
If devm_request_irq() fails, then we are directly return 'ret' without
clk_disable_unprepare(sfc->clk) and clk_disable_unprepare(sfc->hclk).
Fix this by changing direct return to a goto 'err_irq'.
Fixes: 0b89fc0a367e ("spi: rockchip-sfc: add rockchip serial flash controller")
Signed-off-by: Li Lanzhe <u202212060@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230419115030.6029-1-u202212060@hust.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Srinivas Goud <srinivas.goud@amd.com>:
Currently SPI Cadence controller works in Master mode only.
Update driver to support Slave mode and also Full duplex transfer
support in Slave mode
|
|
Currently SPI Cadence controller works only in Master mode.
Updated interrupt handler for Full duplex transfer in Slave mode.
Interrupt handler rely on the TX empty interrupt even for Slave mode
transfer due to below HW limitation.
HW limitation:
AR 65885 - SPI Controller Might Not Update RX_NEMPTY Flag, Showing
Incorrect Status Of The Receive FIFO
SPI Slave mode works in the following manner:
1. One transfer can be finished only after all transfer->len
data been transferred to master device.
2. Slave device only accepts transfer->len data. Any data longer
than this from master device will be dropped. Any data shorter than
this from master will cause SPI to be stuck due to the above behavior.
3. The stale data present in RXFIFO will be dropped in unprepared
hardware transfer function.
Signed-off-by: Srinivas Goud <srinivas.goud@amd.com>
Link: https://lore.kernel.org/r/1681825625-10265-3-git-send-email-srinivas.goud@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace spi_master structure with spi_controller structure.
spi_controller structure provides interface support for
both SPI master and slave controller.
Signed-off-by: Srinivas Goud <srinivas.goud@amd.com>
Link: https://lore.kernel.org/r/1681825625-10265-2-git-send-email-srinivas.goud@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The cadence QSPI driver misbehaves after performing a full system suspend
resume:
...
spi-nor spi0.0: resume() failed
...
This results in a flash connected via OSPI interface after system suspend-
resume to be unusable.
fix these suspend and resume functions.
Fixes: 140623410536 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230417091027.966146-3-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>:
Update Xilinx Versal external DMA read logic to fix random issues
- Instead of having the fixed timeout, update the read timeout based on
the length of the transfer to avoid timeout for larger data size.
- While switching between external DMA read and indirect read, disable the
SPI before configuration and enable it after configuration as recommended
by Octal-SPI Flash Controller specification.
Sai Krishna Potthuri (2):
spi: cadence-quadspi: Update the read timeout based on the length
spi: cadence-quadspi: Disable the SPI before reconfiguring
drivers/spi/spi-cadence-quadspi.c | 40 ++++++++++++++++++-------------
1 file changed, 24 insertions(+), 16 deletions(-)
--
2.25.1
|
|
The AMD Pensando Elba SoC includes a DW apb_ssi v4 controller
with device specific chip-select control. The Elba SoC
provides four chip-selects where the native DW IP supports
two chip-selects. The Elba DW_SPI instance has two native
CS signals that are always overridden.
Signed-off-by: Brad Larson <blarson@amd.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230410184526.15990-11-blarson@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Observed random DMA timeout failures while doing back to back
transfers which involves switching the modes from DMA to NON-DMA.
This issue is observed while testing the OSPI+UBIFS file system test case
where rootfs is mounted from OSPI UBIFS partition.
To avoid this issue, disable the SPI before changing the configuration
from external DMA to NON-DMA and vice versa and reenable it after changing
the configuration.
As per the Cadence Octal SPI design specification, it is recommended to
disable the Octal-SPI enable bit before reconfiguring.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Link: https://lore.kernel.org/r/20230320095931.2651714-3-sai.krishna.potthuri@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When performing indirect read via external DMA the timeout for
completion is set equal to the read length instead of fixed timeout value.
For reads larger than 500 bytes, the timeout will continue to be
equal to the read length whereas for a small read like the Read Status
Register command, the timeout would be 1 or 2 milliseconds. This is not
enough to cover the overhead needed in setting up DMA, in that case make
sure the timeout is at least 500ms to allow DMA to finish. This solution
is inline with the timeout used for Direct read via DMA.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Link: https://lore.kernel.org/r/20230320095931.2651714-2-sai.krishna.potthuri@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix interaction between fw_devlink and DT overlays causing devices to
not be probed
- Fix the compatible string for loongson,cpu-interrupt-controller
* tag 'devicetree-fixes-for-6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
treewide: Fix probing of devices in DT overlays
dt-bindings: interrupt-controller: loongarch: Fix mismatched compatible
|
|
SPI test framework is designed to run each test case for
a list of lengths.
Introduce a module parameter to limit the iterations
to a single value among the list of lengths.
Signed-off-by: Rohit Ner <rohitner@google.com>
Link: https://lore.kernel.org/r/20230412202009.3750955-2-rohitner@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When loading a DT overlay that creates a device, the device is not
probed, unless the DT overlay is unloaded and reloaded again.
After the recent refactoring to improve fw_devlink, it no longer depends
on the "compatible" property to identify which device tree nodes will
become struct devices. fw_devlink now picks up dangling consumers
(consumers pointing to descendent device tree nodes of a device that
aren't converted to child devices) when a device is successfully bound
to a driver. See __fw_devlink_pickup_dangling_consumers().
However, during DT overlay, a device's device tree node can have
sub-nodes added/removed without unbinding/rebinding the driver. This
difference in behavior between the normal device instantiation and
probing flow vs. the DT overlay flow has a bunch of implications that
are pointed out elsewhere[1]. One of them is that the fw_devlink logic
to pick up dangling consumers is never exercised.
This patch solves the fw_devlink issue by marking all DT nodes added by
DT overlays with FWNODE_FLAG_NOT_DEVICE (fwnode that won't become
device), and by clearing the flag when a struct device is actually
created for the DT node. This way, fw_devlink knows not to have
consumers waiting on these newly added DT nodes, and to propagate the
dependency to an ancestor DT node that has the corresponding struct
device.
Based on a patch by Saravana Kannan, which covered only platform and spi
devices.
[1] https://lore.kernel.org/r/CAGETcx_bkuFaLCiPrAWCPQz+w79ccDp6=9e881qmK=vx3hBMyg@mail.gmail.com
Fixes: 4a032827daa89350 ("of: property: Simplify of_link_to_phandle()")
Link: https://lore.kernel.org/r/CAGETcx_+rhHvaC_HJXGrr5_WAd2+k5f=rWYnkCZ6z5bGX-wj4w@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Link: https://lore.kernel.org/r/e1fa546682ea4c8474ff997ab6244c5e11b6f8bc.1680182615.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
This is a driver for the Amlogic SPI flash controller support
on A113L SoC.
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230403183217.13280-3-mmkurbanov@sberdevices.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This helper does not produce a real modalias, but tries to get the
"product" compatible part of the "vendor,product" compatibles only. It
is far from creating a purely useful modalias string and does not seem
to be used like that directly anyway, so let's try to give this helper a
more meaningful name before moving there a real modalias helper (already
existing under of/device.c).
Also update the various documentations to refer to the strings as
"aliases" rather than "modaliases" which has a real meaning in the Linux
kernel.
There is no functional change.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Wolfram Sang <wsa@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20230404172148.82422-9-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
