| Age | Commit message (Collapse) | Author |
|---|
|
Add a driver for the Intel Over-Clocking Watchdog found in Intel
Platform Controller (PCH) chipsets. This watchdog is controlled
via a simple single-register interface and would otherwise be
standard except for the presence of a LOCK bit that can only be
set once per power cycle, needing extra handling around it.
Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20250317-ivo-intel_oc_wdt-v3-1-32c396f4eefd@siemens.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
The S32 platform has several Watchdog Timer available and tied with a
CPU. The SWT0 is the only one which directly asserts the reset line,
other SWT require an external setup to configure the reset behavior
which is not part of this change.
As a side note, in the NXP documentation, the s32g2 and s32g3
reference manuals refer the watchdog as the 'Software Timer Watchdog'
where the name can be misleading as it is actually a hardware
watchdog.
The maximum watchdog timeout value depends on the clock feeding the
SWT counter which is 32bits wide. On the s32g274-rb2, the clock has a
rate of 51MHz which result on 83 seconds maximum timeout.
The timeout can be specified via the device tree with the usual
existing bindings 'timeout-sec' or via the module param timeout.
The watchdog can be loaded with the 'nowayout' option, preventing the
watchdog to be stopped.
The watchdog can be started at boot time with the 'early-enable'
option, thus letting the watchdog framework to service the watchdog
counter.
The watchdog support the magic character to stop when the userspace
releases the device.
Cc: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Cc: Thomas Fossati <thomas.fossati@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Alexandru-Catalin Ionita <alexandru-catalin.ionita@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20250410082616.1855860-3-daniel.lezcano@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Enabling the compile test should not cause automatic enabling of all
drivers.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20250404123941.362620-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Tidy up ACPI ID table:
- drop ACPI_PTR() and hence replace acpi.h with mod_devicetable.h
- remove explicit driver_data initializer
- drop comma in the terminator entry
With that done, extend compile test coverage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20250304140114.1812452-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Watchdog driver implementation for Lenovo SE30 platform.
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20250131204855.1827-1-mpearson-lenovo@squebb.ca
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
RZ/G3E watchdog timer IP is similar to the one found on RZ/V2H. Both these
SoCs belong to the ARCH_RENESAS family. So, it makes sense to use
ARCH_RENESAS rather than ARCH_R9A09G057 to enable the RZV2HWDT driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20250126132633.31956-3-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- Add support for exynosautov920 SoC
- Add support for Airoha EN7851 watchdog
- Add support for MT6735 TOPRGU/WDT
- Delete the cpu5wdt driver
- Always print when registering watchdog fails
- Several other small fixes and improvements
* tag 'linux-watchdog-6.13-rc1' of git://www.linux-watchdog.org/linux-watchdog: (36 commits)
watchdog: rti: of: honor timeout-sec property
watchdog: s3c2410_wdt: add support for exynosautov920 SoC
dt-bindings: watchdog: Document ExynosAutoV920 watchdog bindings
watchdog: mediatek: Add support for MT6735 TOPRGU/WDT
watchdog: mediatek: Make sure system reset gets asserted in mtk_wdt_restart()
dt-bindings: watchdog: fsl-imx-wdt: Add missing 'big-endian' property
dt-bindings: watchdog: Document Qualcomm QCS8300
docs: ABI: Fix spelling mistake in pretimeout_avaialable_governors
Revert "watchdog: s3c2410_wdt: use exynos_get_pmu_regmap_by_phandle() for PMU regs"
watchdog: rzg2l_wdt: Power on the watchdog domain in the restart handler
watchdog: Switch back to struct platform_driver::remove()
watchdog: it87_wdt: add PWRGD enable quirk for Qotom QCML04
watchdog: da9063: Remove __maybe_unused notations
watchdog: da9063: Do not use a global variable
watchdog: Delete the cpu5wdt driver
watchdog: Add support for Airoha EN7851 watchdog
dt-bindings: watchdog: airoha: document watchdog for Airoha EN7581
watchdog: sl28cpld_wdt: don't print out if registering watchdog fails
watchdog: rza_wdt: don't print out if registering watchdog fails
watchdog: rti_wdt: don't print out if registering watchdog fails
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"These are a number of unrelated cleanups, generally simplifying the
architecture specific header files:
- A series from Al Viro simplifies asm/vga.h, after it turns out that
most of it can be generalized.
- A series from Julian Vetter adds a common version of
memcpy_{to,from}io() and memset_io() and changes most architectures
to use that instead of their own implementation
- A series from Niklas Schnelle concludes his work to make PC style
inb()/outb() optional
- Nicolas Pitre contributes improvements for the generic do_div()
helper
- Christoph Hellwig adds a generic version of page_to_phys() and
phys_to_page(), replacing the slightly different architecture
specific definitions.
- Uwe Kleine-Koenig has a minor cleanup for ioctl definitions"
* tag 'asm-generic-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (24 commits)
empty include/asm-generic/vga.h
sparc: get rid of asm/vga.h
asm/vga.h: don't bother with scr_mem{cpy,move}v() unless we need to
vt_buffer.h: get rid of dead code in default scr_...() instances
tty: serial: export serial_8250_warn_need_ioport
lib/iomem_copy: fix kerneldoc format style
hexagon: simplify asm/io.h for !HAS_IOPORT
loongarch: Use new fallback IO memcpy/memset
csky: Use new fallback IO memcpy/memset
arm64: Use new fallback IO memcpy/memset
New implementation for IO memcpy and IO memset
watchdog: Add HAS_IOPORT dependency for SBC8360 and SBC7240
__arch_xprod64(): make __always_inline when optimizing for performance
ARM: div64: improve __arch_xprod_64()
asm-generic/div64: optimize/simplify __div64_const32()
lib/math/test_div64: add some edge cases relevant to __div64_const32()
asm-generic: add an optional pfn_valid check to page_to_phys
asm-generic: provide generic page_to_phys and phys_to_page implementations
asm-generic/io.h: Remove I/O port accessors for HAS_IOPORT=n
tty: serial: handle HAS_IOPORT dependencies
...
|
|
PMU regs"
This reverts commit 746f0770f916e6c48e422d6a34e67eae16707f0e.
Now that we can register a SoC specific regmap with syscon using
of_syscon_register_regmap() api we can switch back to using
syscon_regmap_lookup_by_phandle() in the client drivers.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241029191131.2329414-1-peter.griffin@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
This driver has a number of issues (accesses arbitrary I/O ports
without identifying the hardware, doesn't document what hardware it
supports, suspiciously inconsistent locking model, doesn't implement
WDIOC_SETTIMEOUT, potential integer overflow...)
The driver was added in 2003 and there's no evidence that it has any
recent user, all changes seem to be tree-wide, subsystem-wide, or the
result of static code analysis. So I believe we should simply drop
this legacy piece of code.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Message-ID: <20241011170710.484a257a@endymion.delvare>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241022114731.31f69c94@endymion.delvare
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Add support for Airoha EN7851 watchdog. This is a very basic watchdog
with no pretimeout support, max timeout is 28 seconds and it ticks based
on half the SoC BUS clock.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241011104411.28659-2-ansuelsmth@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Both drivers use I/O port accesses without declaring a dependency on
CONFIG_HAS_IOPORT. For sbc8360_wdt this causes a compile error on UML
once inb()/outb() helpers become conditional.
For sbc7240_wdt this causes no such errors with UML because this driver
depends on both x86_32 and !UML. Nevertheless add HAS_IOPORT as
a dependency for both drivers to be explicit and drop the !UML
dependency for sbc7240_wdt as it is now redundant since UML implies no
HAS_IOPORT.
Fixes: 52df67b6b313 ("watchdog: add HAS_IOPORT dependencies")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add watchdog timer support for the Congatec Board Controller.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20241001-congatec-board-controller-v3-4-39ceceed5c47@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add Watchdog Timer driver for RZ/V2H(P) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240829193831.80768-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- make watchdog_class const
- rework of the rzg2l_wdt driver
- other small fixes and improvements
* tag 'linux-watchdog-6.11-rc1' of git://www.linux-watchdog.org/linux-watchdog:
dt-bindings: watchdog: dlg,da9062-watchdog: Drop blank space
watchdog: rzn1: Convert comma to semicolon
watchdog: lenovo_se10_wdt: Convert comma to semicolon
dt-bindings: watchdog: renesas,wdt: Document RZ/G3S support
watchdog: rzg2l_wdt: Add suspend/resume support
watchdog: rzg2l_wdt: Rely on the reset driver for doing proper reset
watchdog: rzg2l_wdt: Remove comparison with zero
watchdog: rzg2l_wdt: Remove reset de-assert from probe
watchdog: rzg2l_wdt: Check return status of pm_runtime_put()
watchdog: rzg2l_wdt: Use pm_runtime_resume_and_get()
watchdog: rzg2l_wdt: Make the driver depend on PM
watchdog: rzg2l_wdt: Restrict the driver to ARCH_RZG2L and ARCH_R9A09G011
watchdog: imx7ulp_wdt: keep already running watchdog enabled
watchdog: starfive: Add missing clk_disable_unprepare()
watchdog: Make watchdog_class const
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- ROHM BD96801 Power Management IC
- Cirrus Logic CS40L50 Haptic Driver with Waveform Memory
- Marvell 88PM886 Power Management IC
New Device Support:
- Keyboard Backlight to ChromeOS Embedded Controller
- LEDs to ChromeOS Embedded Controller
- Charge Control to ChromeOS Embedded Controller
- HW Monitoring Service to ChromeOS Embedded Controller
- AUXADCs to MediaTek MT635{7,8,9} Power Management ICs
New Functionality:
- Allow Syscon consumers to supply their own Regmaps on registration
Fix-ups:
- Constify/staticise applicable data structures
- Remove superfluous/duplicated/unused sections
- Device Tree binding adaptions/conversions/creation
- Trivial; spelling, whitespace, coding-style adaptions
- Utilise centrally provided helpers and macros to aid
simplicity/duplication
- Drop i2c_device_id::driver_data where the value is unused
- Replace ACPI/DT firmware helpers with agnostic variants
- Move over to GPIOD (descriptor-based) APIs
- Annotate a bunch of __counted_by() cases
- Straighten out some includes
Bug Fixes:
- Ensure potentially asserted recent lines are deasserted during
initialisation
- Avoid "<module>.ko is added to multiple modules" warnings
- Supply a bunch of MODULE_DESCRIPTIONs to silence modpost warnings
- Fix Wvoid-pointer-to-enum-cast warnings"
* tag 'mfd-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (87 commits)
mfd: timberdale: Attach device properties to TSC2007 board info
mfd: tmio: Move header to platform_data
mfd: tmio: Sanitize comments
mfd: tmio: Update include files
mmc: tmio/sdhi: Fix includes
mfd: tmio: Remove obsolete io accessors
mfd: tmio: Remove obsolete platform_data
watchdog: bd96801_wdt: Add missing include for FIELD_*()
dt-bindings: mfd: syscon: Add APM poweroff mailbox
dt-bindings: mfd: syscon: Split and enforce documenting MFD children
dt-bindings: mfd: rk817: Merge support for RK809
dt-bindings: mfd: rk817: Fixup clocks and reference dai-common
dt-bindings: mfd: syscon: Add TI's opp table compatible
mfd: omap-usb-tll: Use struct_size to allocate tll
dt-bindings: mfd: Explain lack of child dependency in simple-mfd
dt-bindings: mfd: Dual licensing for st,stpmic1 bindings
mfd: omap-usb-tll: Annotate struct usbtll_omap with __counted_by
mfd: tps6594-core: Remove unneeded semicolon in tps6594_check_crc_mode()
mfd: lm3533: Move to new GPIO descriptor-based APIs
mfd: tps65912: Use devm helper functions to simplify probe
...
|
|
The rzg2l_wdt watchdog driver cannot work w/o CONFIG_PM=y (e.g. the
clocks are enabled though pm_runtime_* specific APIs). To avoid building
a driver that doesn't work make explicit the dependency on CONFIG_PM.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240531065723.1085423-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
The rzg2l_wdt driver is used only by ARCH_RZG2L and ARCH_R9A09G011
micro-architectures of Renesas. Thus, limit it's usage only to these.
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240531065723.1085423-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Introduce driver for WDG block on ROHM BD96801 scalable PMIC.
This driver only supports watchdog with I2C feeding and delayed
response detection. Whether the watchdog toggles PRSTB pin or
just causes an interrupt can be configured via device-tree.
The BD96801 PMIC HW supports also window watchdog (too early
feeding detection) and Q&A mode. These are not supported by
this driver.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/bb3a49d606e793a61b0c033170ff2a9f30f3c2a5.1719473802.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Once the inb()/outb() helpers become conditional, the newly added driver
fails to link on targets without CONFIG_HAS_IOPORT:
In file included from arch/arm64/include/asm/io.h:299,
from include/linux/io.h:14,
from drivers/watchdog/lenovo_se10_wdt.c:8:
drivers/watchdog/lenovo_se10_wdt.c: In function 'set_bram':
include/asm-generic/io.h:596:15: error: call to '_outb' declared with attribute error: outb() requires CONFIG_HAS_IOPORT
596 | #define _outb _outb
include/asm-generic/io.h:655:14: note: in expansion of macro '_outb'
655 | #define outb _outb
| ^~~~~
drivers/watchdog/lenovo_se10_wdt.c:67:9: note: in expansion of macro 'outb'
67 | outb(offset, bram_base);
| ^~~~
Add the same dependency we added to the other such drivers.
Fixes: 1f6602c8ed1e ("watchdog: lenovo_se10_wdt: Watchdog driver for Lenovo SE10 platform")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240528120759.3491774-1-arnd@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
The Lenovo SE10 watchdog is only present on Lenovo ThinkEdge SE10
platforms, which are based on Intel Atom SoCs, and its driver relies on
DMI tables. Hence add dependencies on X86 && DMI, to prevent asking the
user about this driver when configuring a kernel without Intel Atom or
DMI support.
While at it, fix the odd indentation (spaces instead of TABs).
Fixes: 1f6602c8ed1eccac ("watchdog: lenovo_se10_wdt: Watchdog driver for Lenovo SE10 platform")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/58005595a05ef803b454b78d3ae9b8ee0675bd5d.1715076440.git.geert+renesas@glider.be
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for those
drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240410084201.1481930-2-schnelle@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Watchdog driver implementation for Lenovo SE10 platform.
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: David Ober <dober@lenovo.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240315195227.91282-1-mpearson-lenovo@squebb.ca
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- Add support for Watchdog to ChromeOS Embedded Controller
- Add support for GPIOs to ChromeOS Embedded Controller
- Add supprt for Sound to MediaTek MT6357 CODEC
New Functionality:
- Add power-off functionality to Texas Instruments TWL series CODECs
Fix-ups:
- Device Tree binding adaptions/conversions/creation
- Use/convert to new/better APIs/helpers/MACROs instead of
hand-rolling implementations
- Trivial; spelling, whitespace, clean-ups, etc
- Remove superfluous code and simplify overall
- Fix include lists; alphabetise, remove unused, explicitly add used
- Use dev_err_probe() to clean-up error paths
- Convert used cache type over to the Maple Tree in many instances
- Constify a bunch of static structs
- Refrain from over-riding resources provided via the firmware
Bug Fixes:
- Fix a clock related firmware bug on Dell XPS 9530 et al.
- Repair incorrect IRQ designations
- Increase buffer sizes to omit various snprintf compiler errors
- Ensure errors are handled properly
- Balance references and prevent resource leaks
- Rectify Power Key interrupt processing
- Fix Kconfig related build errors
- Correct a bunch of register start-up default values"
* tag 'mfd-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (65 commits)
mfd: cs42l43: Fix wrong GPIO_FN_SEL and SPI_CLK_CONFIG1 defaults
mfd: cs42l43: Fix wrong register defaults
mfd: mt6397-core: Register mt6357 sound codec
dt-bindings: mfd: syscon: Add ti,am62-usb-phy-ctrl compatible
dt-bindings: mfd: dlg,da9063: Make #interrupt-cells required
dt-bindings: mfd: Convert atmel-flexcom to json-schema
mfd: kempld-core: Don't replace resources provided by ACPI
mfd: cros_ec_dev: Add GPIO device if feature present on EC
dt-bindings: mfd: cros-ec: Add properties for GPIO controller
mfd: twl: Select MFD_CORE
mfd: core: Constify the struct device_type usage
mfd: rk8xx-core: Fix interrupt processing order for power key button
mfd: twl4030-power: Accept standard property for power controller
mfd: twl-core: Add power off implementation for twl603x
dt-bindings: mfd: ti,twl: Document system-power-controller
mfd: altera-sysmgr: Call of_node_put() only when of_parse_phandle() takes a ref
mfd: syscon: Remove extern from function prototypes
mfd: syscon: Call of_node_put() only when of_parse_phandle() takes a ref
mfd: mc13xxx: Use bitfield helpers
mfd: rc5t583: Convert to use maple tree register cache
...
|
|
Obtain the PMU regmap using the new API added to exynos-pmu driver rather
than syscon_regmap_lookup_by_phandle(). As this driver no longer depends
on mfd syscon remove that header and Kconfig dependency.
Tested-by: Alexey Klimov <alexey.klimov@linaro.org>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240220220613.797068-3-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Embedded Controller (EC) present on Chromebook devices
can be used as a watchdog.
Implement a driver to support it.
Signed-off-by: Lukasz Majczak <lma@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240126095721.782782-3-lma@chromium.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Pull MIPS updates from Thomas Bogendoerfer:
- removed AR7 platform support
- cleanups and fixes
* tag 'mips_6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: AR7: remove platform
watchdog: ar7_wdt: remove driver to prepare for platform removal
vlynq: remove bus driver
mtd: parsers: ar7: remove support
serial: 8250: remove AR7 support
arch: mips: remove ReiserFS from defconfig
MIPS: lantiq: Remove unnecessary include of <linux/of_irq.h>
MIPS: lantiq: Fix pcibios_plat_dev_init() "no previous prototype" warning
MIPS: KVM: Fix a build warning about variable set but not used
MIPS: Remove dead code in relocate_new_kernel
mips: dts: ralink: mt7621: rename to GnuBee GB-PC1 and GnuBee GB-PC2
mips: dts: ralink: mt7621: define each reset as an item
mips: dts: ingenic: Remove unneeded probe-type properties
MIPS: loongson32: Remove dma.h and nand.h
|
|
AR7 is going to be removed from the Kernel, so remove its watchdog
support. This allows us to remove the platform because this driver
includes a platform specific header.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The Itanium architecture is obsolete, and an informal survey [0] reveals
that any residual use of Itanium hardware in production is mostly HP-UX
or OpenVMS based. The use of Linux on Itanium appears to be limited to
enthusiasts that occasionally boot a fresh Linux kernel to see whether
things are still working as intended, and perhaps to churn out some
distro packages that are rarely used in practice.
None of the original companies behind Itanium still produce or support
any hardware or software for the architecture, and it is listed as
'Orphaned' in the MAINTAINERS file, as apparently, none of the engineers
that contributed on behalf of those companies (nor anyone else, for that
matter) have been willing to support or maintain the architecture
upstream or even be responsible for applying the odd fix. The Intel
firmware team removed all IA-64 support from the Tianocore/EDK2
reference implementation of EFI in 2018. (Itanium is the original
architecture for which EFI was developed, and the way Linux supports it
deviates significantly from other architectures.) Some distros, such as
Debian and Gentoo, still maintain [unofficial] ia64 ports, but many have
dropped support years ago.
While the argument is being made [1] that there is a 'for the common
good' angle to being able to build and run existing projects such as the
Grid Community Toolkit [2] on Itanium for interoperability testing, the
fact remains that none of those projects are known to be deployed on
Linux/ia64, and very few people actually have access to such a system in
the first place. Even if there were ways imaginable in which Linux/ia64
could be put to good use today, what matters is whether anyone is
actually doing that, and this does not appear to be the case.
There are no emulators widely available, and so boot testing Itanium is
generally infeasible for ordinary contributors. GCC still supports IA-64
but its compile farm [3] no longer has any IA-64 machines. GLIBC would
like to get rid of IA-64 [4] too because it would permit some overdue
code cleanups. In summary, the benefits to the ecosystem of having IA-64
be part of it are mostly theoretical, whereas the maintenance overhead
of keeping it supported is real.
So let's rip off the band aid, and remove the IA-64 arch code entirely.
This follows the timeline proposed by the Debian/ia64 maintainer [5],
which removes support in a controlled manner, leaving IA-64 in a known
good state in the most recent LTS release. Other projects will follow
once the kernel support is removed.
[0] https://lore.kernel.org/all/CAMj1kXFCMh_578jniKpUtx_j8ByHnt=s7S+yQ+vGbKt9ud7+kQ@mail.gmail.com/
[1] https://lore.kernel.org/all/0075883c-7c51-00f5-2c2d-5119c1820410@web.de/
[2] https://gridcf.org/gct-docs/latest/index.html
[3] https://cfarm.tetaneutral.net/machines/list/
[4] https://lore.kernel.org/all/87bkiilpc4.fsf@mid.deneb.enyo.de/
[5] https://lore.kernel.org/all/ff58a3e76e5102c94bb5946d99187b358def688a.camel@physik.fu-berlin.de/
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add marvell GTI watchdog driver
- add support for Amlogic-T7 SoCs
- document the IPQ5018 watchdog compatible
- enable COMPILE_TEST for more watchdog device drivers
- core: stop watchdog when executing poweroff command
- other small improvements and fixes
* tag 'linux-watchdog-6.6-rc1' of git://www.linux-watchdog.org/linux-watchdog: (21 commits)
watchdog: Add support for Amlogic-T7 SoCs
watchdog: Add a new struct for Amlogic-GXBB driver
dt-bindings: watchdog: Add support for Amlogic-T7 SoCs
dt-bindings: watchdog: qcom-wdt: document IPQ5018
watchdog: imx2_wdt: Improve dev_crit() message
watchdog: stm32: Drop unnecessary of_match_ptr()
watchdog: sama5d4: readout initial state
watchdog: intel-mid_wdt: add MODULE_ALIAS() to allow auto-load
watchdog: core: stop watchdog when executing poweroff command
watchdog: pm8916_wdt: Remove redundant of_match_ptr()
watchdog: xilinx_wwdt: Use div_u64() in xilinx_wwdt_start()
watchdog: starfive: Remove #ifdef guards for PM related functions
watchdog: s3c2410: Fix potential deadlock on &wdt->lock
watchdog:rit_wdt: Add support for WDIOF_CARDRESET
dt-bindings: watchdog: ti,rti-wdt: Add support for WDIOF_CARDRESET
watchdog: Enable COMPILE_TEST for more drivers
watchdog: advantech_ec_wdt: fix Kconfig dependencies
watchdog: Explicitly include correct DT includes
Watchdog: Add marvell GTI watchdog driver
dt-bindings: watchdog: marvell GTI system watchdog driver
...
|
|
While it's pretty much theoretical to be otherwise, make sure
that P2SB is selected only for X86. This is idiomatic dependency
which is used by all others who select it. Use it for Simatic
as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230822141859.2139630-1-andriy.shevchenko@linux.intel.com
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The simatic-ipc driver no longer depends on PCI, but its watchdog portion
still needs it, otherwise P2SB runs into a build failure:
WARNING: unmet direct dependencies detected for P2SB
Depends on [n]: PCI [=n] && X86 [=y]
Selected by [m]:
- SIEMENS_SIMATIC_IPC_WDT [=m] && WATCHDOG [=y] && SIEMENS_SIMATIC_IPC [=y]
drivers/platform/x86/p2sb.c:121:3: error: call to undeclared function 'pci_bus_write_config_dword'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
pci_bus_write_config_dword(bus, devfn_p2sb, P2SBC, 0);
Add back the minimum dependendency to make it build in random
configurations again.
Fixes: b72da71ce24b ("platform/x86: simatic-ipc: drop PCI runtime depends and header")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230814073924.1066390-1-arnd@kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
There's quite a few watchdog drivers which are easily enabled for
COMPILE_TEST, so let's enable them.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230728195022.1198555-1-robh@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
This driver uses the WATCHDOG_CORE framework and ISA_BUS_API.
This commit has these dependencies correctly selected.
Signed-off-by: Florent CARLI <fcarli@gmail.com>
Co-authored-by: Yoann Congal <yoann.congal@smile.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230721081347.52069-1-fcarli@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
This patch add support for Marvell GTI watchdog. Global timer
unit (GTI) support hardware watchdog timer. Software programs
watchdog timer to generate interrupt on first timeout, second
timeout is configured to be ignored and system reboots on
third timeout.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230803032523.6242-2-bbhushan2@marvell.com
[groeck: MODULE_LICENSE GPL v2 -> GPL since that is sufficient]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
If a user did choose to enable Siemens Simatic platform support they
likely want that driver to be enabled without having to flip more config
switches. So we make the watchdog driver config switch default to the
platform driver switches value.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230719153518.13073-2-henning.schild@siemens.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Versal watchdog driver uses window watchdog mode. Window watchdog
timer(WWDT) contains closed(first) and open(second) window with
32 bit width. Write to the watchdog timer within predefined window
periods of time. This means a period that is not too soon and a
period that is not too late. The WWDT has to be restarted within
the open window time. If software tries to restart WWDT outside of
the open window time period, it generates a reset.
Signed-off-by: Srinivas Neeli <srinivas.neeli@amd.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20230420104231.2243079-4-srinivas.neeli@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Add watchdog driver for the StarFive JH7100 and JH7110 SoC.
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230314132437.121534-3-xingyu.wu@starfivetech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- qcom-wdt dt-bindings improvements and additions (like MSM8994 and
MDM9615)
- mtk_wdt: Add reset_by_toprgu support
- devm_clk_get_enabled() helper changes
- Fix kmemleak in watchdog_cdev_register
- watchdog sysfs improvements
- Other fixes and small improvements
* tag 'linux-watchdog-6.3-rc1' of git://www.linux-watchdog.org/linux-watchdog: (52 commits)
watchdog: at91rm9200: Only warn once about problems in .remove()
watchdog: mt7621-wdt: avoid ralink architecture dependent code
watchdog: mt7621-wdt: avoid static global declarations
dt-bindings: watchdog: mt7621-wdt: add phandle to access system controller registers
watchdog: sbsa_wdog: Make sure the timeout programming is within the limits
dt-bindings: watchdog: qcom-wdt: add qcom,apss-wdt-sa8775p compatible
watchdog: report options in sysfs
watchdog: report fw_version in sysfs
dt-bindings: watchdog: fsl-imx: document suspend in wait mode
watchdog: imx2_wdg: suspend watchdog in WAIT mode
watchdog: pcwd_usb: Fix attempting to access uninitialized memory
dt-bindings: watchdog: qcom-wdt: merge MSM timer
dt-bindings: watchdog: qcom-wdt: allow interrupts
dt-bindings: watchdog: qcom-wdt: add qcom,kpss-wdt-mdm9615
dt-bindings: watchdog: qcom-wdt: fix list of MSM timer compatibles
dt-bindings: watchdog: qcom-wdt: do not allow fallback alone
dt-bindings: watchdog: qcom-wdt: require fallback for IPQ4019
watchdog: Fix kmemleak in watchdog_cdev_register
watchdog: Include <linux/kstrtox.h> when appropriate
watchdog: at91sam9_wdt: use devm_request_irq to avoid missing free_irq() in error path
...
|
|
MT7621 SoC has a system controller node. Watchdog need to access to reset
status register. Ralink architecture and related driver are old and from
the beggining they are using some architecture dependent operations for
accessing this shared registers through 'asm/mach-ralink/ralink_regs.h'
header file. However this is not ideal from a driver perspective which can
just access to the system controller registers in an arch independent way
using regmap syscon APIs. Update Kconfig accordingly to select new added
dependencies and allow driver to be compile tested.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230214103936.1061078-6-sergio.paracuellos@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds the 'advantech_ec_wdt' kernel module which provides
WDT support for Advantech platforms with ITE based Embedded Controller.
Signed-off-by: Thomas Kastner <thomas.kastner@advantech.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Thomas Kastner <thomas.kastner@advantech.com>
Link: https://lore.kernel.org/r/Y0+pl/26e3pcEUPk@EIS-S230
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- new driver for Exar/MaxLinear XR28V38x
- support for exynosautov9 SoC
- support for Renesas R-Car V5H (R8A779G0) and RZ/V2M (r9a09g011) SoC
- support for imx93
- several other fixes and improvements
* tag 'linux-watchdog-6.1-rc1' of git://www.linux-watchdog.org/linux-watchdog: (36 commits)
watchdog: twl4030_wdt: add missing mod_devicetable.h include
dt-bindings: watchdog: migrate mt7621 text bindings to YAML
watchdog: sp5100_tco: Add "action" module parameter
watchdog: imx93: add watchdog timer on imx93
watchdog: imx7ulp_wdt: init wdog when it was active
watchdog: imx7ulp_wdt: Handle wdog reconfigure failure
watchdog: imx7ulp_wdt: Fix RCS timeout issue
watchdog: imx7ulp_wdt: Check CMD32EN in wdog init
watchdog: imx7ulp: Add explict memory barrier for unlock sequence
watchdog: imx7ulp: Move suspend/resume to noirq phase
watchdog: rti-wdt:using the pm_runtime_resume_and_get to simplify the code
dt-bindings: watchdog: rockchip: add rockchip,rk3128-wdt
watchdog: s3c2410_wdt: support exynosautov9 watchdog
dt-bindings: watchdog: add exynosautov9 compatible
watchdog: npcm: Enable clock if provided
watchdog: meson: keep running if already active
watchdog: dt-bindings: atmel,at91sam9-wdt: convert to json-schema
watchdog: armada_37xx_wdt: Fix .set_timeout callback
watchdog: sa1100: make variable sa1100dog_driver static
watchdog: w83977f_wdt: Fix comment typo
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Remove our now never-true definitions for pgd_huge() and p4d_leaf().
- Add pte_needs_flush() and huge_pmd_needs_flush() for 64-bit.
- Add support for syscall wrappers.
- Add support for KFENCE on 64-bit.
- Update 64-bit HV KVM to use the new guest state entry/exit accounting
API.
- Support execute-only memory when using the Radix MMU (P9 or later).
- Implement CONFIG_PARAVIRT_TIME_ACCOUNTING for pseries guests.
- Updates to our linker script to move more data into read-only
sections.
- Allow the VDSO to be randomised on 32-bit.
- Many other small features and fixes.
Thanks to Andrew Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Athira
Rajeev, Christophe Leroy, David Hildenbrand, Disha Goel, Fabiano Rosas,
Gaosheng Cui, Gustavo A. R. Silva, Haren Myneni, Hari Bathini, Jilin
Yuan, Joel Stanley, Kajol Jain, Kees Cook, Krzysztof Kozlowski, Laurent
Dufour, Liang He, Li Huafei, Lukas Bulwahn, Madhavan Srinivasan, Nathan
Chancellor, Nathan Lynch, Nicholas Miehlbradt, Nicholas Piggin, Pali
Rohár, Rohan McLure, Russell Currey, Sachin Sant, Segher Boessenkool,
Shrikanth Hegde, Tyrel Datwyler, Wolfram Sang, ye xingchen, and Zheng
Yongjun.
* tag 'powerpc-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (214 commits)
KVM: PPC: Book3S HV: Fix stack frame regs marker
powerpc: Don't add __powerpc_ prefix to syscall entry points
powerpc/64s/interrupt: Fix stack frame regs marker
powerpc/64: Fix msr_check_and_set/clear MSR[EE] race
powerpc/64s/interrupt: Change must-hard-mask interrupt check from BUG to WARN
powerpc/pseries: Add firmware details to the hardware description
powerpc/powernv: Add opal details to the hardware description
powerpc: Add device-tree model to the hardware description
powerpc/64: Add logical PVR to the hardware description
powerpc: Add PVR & CPU name to hardware description
powerpc: Add hardware description string
powerpc/configs: Enable PPC_UV in powernv_defconfig
powerpc/configs: Update config files for removed/renamed symbols
powerpc/mm: Fix UBSAN warning reported on hugetlb
powerpc/mm: Always update max/min_low_pfn in mem_topology_setup()
powerpc/mm/book3s/hash: Rename flush_tlb_pmd_range
powerpc: Drops STABS_DEBUG from linker scripts
powerpc/64s: Remove lost/old comment
powerpc/64s: Remove old STAB comment
powerpc: remove orphan systbl_chk.sh
...
|
|
Simple driver for the watchdog present in some Exar/MaxLinear UART chips.
Please see https://www.maxlinear.com/product/interface/uarts/lpc-uarts/xr28v384
for more info.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220914094605.93377-1-d.mueller@elsoft.ch
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Enable HP_WATCHDOG for ARM64 systems.
HPWDT_NMI_DECODING requires X86 as NMI handlers are X86 specific.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220820202821.1263837-3-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
CONFIG_PPC_FSL_BOOK3E is redundant with CONFIG_PPC_E500.
Replace it so that CONFIG_PPC_FSL_BOOK3E can be removed later.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/01a9132d51d3d8d9c74576d3da4d9d1fa5a88bde.1663606876.git.christophe.leroy@csgroup.eu
|
|
With Broadcom Broadband arch ARCH_BCMBCA supported in the kernel, this
patch series migrate the ARCH_BCM4908 symbol to ARCH_BCMBCA. Hence
replace ARCH_BCM4908 with ARCH_BCMBCA in subsystem Kconfig files.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> (for watchdog)
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (for drivers/pci)
Acked-by: Wolfram Sang <wsa@kernel.org> (for i2c)
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> (for reset)
Link: https://lore.kernel.org/r/20220803175455.47638-7-william.zhang@broadcom.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add support for syscall stack randomization
- Add support for atomic operations to the 32 & 64-bit BPF JIT
- Full support for KASAN on 64-bit Book3E
- Add a watchdog driver for the new PowerVM hypervisor watchdog
- Add a number of new selftests for the Power10 PMU support
- Add a driver for the PowerVM Platform KeyStore
- Increase the NMI watchdog timeout during live partition migration, to
avoid timeouts due to increased memory access latency
- Add support for using the 'linux,pci-domain' device tree property for
PCI domain assignment
- Many other small features and fixes
Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira
Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas,
Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A.
Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch,
Naveen N. Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár,
Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher
Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, and Zhouyi Zhou.
* tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits)
powerpc/64e: Fix kexec build error
EDAC/ppc_4xx: Include required of_irq header directly
powerpc/pci: Fix PHB numbering when using opal-phbid
powerpc/64: Init jump labels before parse_early_param()
selftests/powerpc: Avoid GCC 12 uninitialised variable warning
powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
powerpc/xive: Fix refcount leak in xive_get_max_prio
powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
powerpc/perf: Include caps feature for power10 DD1 version
powerpc: add support for syscall stack randomization
powerpc: Move system_call_exception() to syscall.c
powerpc/powernv: rename remaining rng powernv_ functions to pnv_
powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
powerpc/powernv: Avoid crashing if rng is NULL
selftests/powerpc: Fix matrix multiply assist test
powerpc/signal: Update comment for clarity
powerpc: make facility_unavailable_exception 64s
powerpc/platforms/83xx/suspend: Remove write-only global variable
powerpc/platforms/83xx/suspend: Prevent unloading the driver
powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration
...
|
|
PAPR v2.12 defines a new hypercall, H_WATCHDOG. The hypercall permits
guest control of one or more virtual watchdog timers. The timers have
millisecond granularity. The guest is terminated when a timer
expires.
This patch adds a watchdog driver for these timers, "pseries-wdt".
pseries_wdt_probe() currently assumes the existence of only one
platform device and always assigns it watchdogNumber 1. If we ever
expose more than one timer to userspace we will need to devise a way
to assign a distinct watchdogNumber to each platform device at device
registration time.
Signed-off-by: Scott Cheloha <cheloha@linux.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220713202335.1217647-5-cheloha@linux.ibm.com
|
