diff options
| author | Linus Torvalds <torvalds@linux-foundation.org> | 2019-03-06 16:35:12 -0800 |
|---|---|---|
| committer | Linus Torvalds <torvalds@linux-foundation.org> | 2019-03-06 16:35:12 -0800 |
| commit | 67e79a6dc2664a3ef85113440e60f7aaca3c7815 (patch) | |
| tree | 206f8a84da0aefca8c588e31f812bd208e7a34a4 | |
| parent | e266ca36da7de45b64b05698e98e04b578a88888 (diff) | |
| parent | f694936c3b5a4c140ded5b673555d95aedc866b9 (diff) | |
Merge tag 'tty-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" patchset for the tty/serial driver layer for
5.1-rc1.
It's really not all that big, nothing major here.
There are a lot of tiny driver fixes and updates, combined with other
cleanups for different serial drivers and the vt layer. Full details
are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'tty-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (70 commits)
tty: xilinx_uartps: Correct return value in probe
serial: sprd: Modify the baud rate calculation formula
dt-bindings: serial: Add Milbeaut serial driver description
serial: 8250_of: assume reg-shift of 2 for mrvl,mmp-uart
serial: 8250_pxa: honor the port number from devicetree
tty: hvc_xen: Mark expected switch fall-through
tty: n_gsm: Mark expected switch fall-throughs
tty: serial: msm_serial: Remove __init from msm_console_setup()
tty: serial: samsung: Enable baud clock during initialisation
serial: uartps: Fix stuck ISR if RX disabled with non-empty FIFO
tty: serial: remove redundant likely annotation
tty/n_hdlc: mark expected switch fall-through
serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()
serial: 8250_pci: Fix number of ports for ACCES serial cards
vt: perform safe console erase in the right order
tty/nozomi: use pci_iomap instead of ioremap_nocache
tty/synclink: remove ISA support
serial: 8250_pci: Replace custom code with pci_match_id()
serial: max310x: Correction of the initial setting of the MODE1 bits for various supported ICs.
serial: mps2-uart: Add parentheses around conditional in mps2_uart_shutdown
...
50 files changed, 1672 insertions, 772 deletions
diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index da50321da34d..3cba12f855b7 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -21,6 +21,7 @@ Required properties: - "altr,16550-FIFO128" - "fsl,16550-FIFO64" - "fsl,ns16550" + - "intel,xscale-uart" - "ti,da830-uart" - "aspeed,ast2400-vuart" - "aspeed,ast2500-vuart" diff --git a/Documentation/devicetree/bindings/serial/ingenic,uart.txt b/Documentation/devicetree/bindings/serial/ingenic,uart.txt index c3c6406d5cfe..24ed8769f4af 100644 --- a/Documentation/devicetree/bindings/serial/ingenic,uart.txt +++ b/Documentation/devicetree/bindings/serial/ingenic,uart.txt @@ -6,7 +6,8 @@ Required properties: - "ingenic,jz4760-uart", - "ingenic,jz4770-uart", - "ingenic,jz4775-uart", - - "ingenic,jz4780-uart". + - "ingenic,jz4780-uart", + - "ingenic,x1000-uart". - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. - clocks : phandles to the module & baud clocks. diff --git a/Documentation/devicetree/bindings/serial/milbeaut-uart.txt b/Documentation/devicetree/bindings/serial/milbeaut-uart.txt new file mode 100644 index 000000000000..3d2fb1a7ba94 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/milbeaut-uart.txt @@ -0,0 +1,21 @@ +Socionext Milbeaut UART controller + +Required properties: +- compatible: should be "socionext,milbeaut-usio-uart". +- reg: offset and length of the register set for the device. +- interrupts: two interrupts specifier. +- interrupt-names: should be "rx", "tx". +- clocks: phandle to the input clock. + +Optional properties: +- auto-flow-control: flow control enable. + +Example: + usio1: usio_uart@1e700010 { + compatible = "socionext,milbeaut-usio-uart"; + reg = <0x1e700010 0x10>; + interrupts = <0 141 0x4>, <0 149 0x4>; + interrupt-names = "rx", "tx"; + clocks = <&clk 2>; + auto-flow-control; + }; diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.txt new file mode 100644 index 000000000000..085a8591accd --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.txt @@ -0,0 +1,35 @@ +NVIDIA Tegra Combined UART (TCU) + +The TCU is a system for sharing a hardware UART instance among multiple +systems within the Tegra SoC. It is implemented through a mailbox- +based protocol where each "virtual UART" has a pair of mailboxes, one +for transmitting and one for receiving, that is used to communicate +with the hardware implementing the TCU. + +Required properties: +- name : Should be tcu +- compatible + Array of strings + One of: + - "nvidia,tegra194-tcu" +- mbox-names: + "rx" - Mailbox for receiving data from hardware UART + "tx" - Mailbox for transmitting data to hardware UART +- mboxes: Mailboxes corresponding to the mbox-names. + +This node is a mailbox consumer. See the following files for details of +the mailbox subsystem, and the specifiers implemented by the relevant +provider(s): + +- .../mailbox/mailbox.txt +- .../mailbox/nvidia,tegra186-hsp.txt + +Example bindings: +----------------- + +tcu: tcu { + compatible = "nvidia,tegra194-tcu"; + mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_SM 0>, + <&hsp_aon TEGRA_HSP_MBOX_TYPE_SM 1>; + mbox-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/serial/omap_serial.txt b/Documentation/devicetree/bindings/serial/omap_serial.txt index c35d5ece1156..0a9b5444f4e6 100644 --- a/Documentation/devicetree/bindings/serial/omap_serial.txt +++ b/Documentation/devicetree/bindings/serial/omap_serial.txt @@ -22,6 +22,8 @@ Optional properties: - dma-names : "rx" for receive channel, "tx" for transmit channel. - rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt - rs485-rts-active-high: drive RTS high when sending (default is low). +- clocks: phandle to the functional clock as per + Documentation/devicetree/bindings/clock/clock-bindings.txt Example: diff --git a/Documentation/devicetree/bindings/serial/pl011.txt b/Documentation/devicetree/bindings/serial/pl011.txt deleted file mode 100644 index 77863aefe9ef..000000000000 --- a/Documentation/devicetree/bindings/serial/pl011.txt +++ /dev/null @@ -1,51 +0,0 @@ -* ARM AMBA Primecell PL011 serial UART - -Required properties: -- compatible: must be "arm,primecell", "arm,pl011", "zte,zx296702-uart" -- reg: exactly one register range with length 0x1000 -- interrupts: exactly one interrupt specifier - -Optional properties: -- pinctrl: - When present, must have one state named "default", - and may contain a second name named "sleep". The former - state sets up pins for ordinary operation whereas - the latter state will put the associated pins to sleep - when the UART is unused -- clocks: - When present, the first clock listed must correspond to - the clock named UARTCLK on the IP block, i.e. the clock - to the external serial line, whereas the second clock - must correspond to the PCLK clocking the internal logic - of the block. Just listing one clock (the first one) is - deprecated. -- clock-names: - When present, the first clock listed must be named - "uartclk" and the second clock listed must be named - "apb_pclk" -- dmas: - When present, may have one or two dma channels. - The first one must be named "rx", the second one - must be named "tx". -- auto-poll: - Enables polling when using RX DMA. -- poll-rate-ms: - Rate at which poll occurs when auto-poll is set, - default 100ms. -- poll-timeout-ms: - Poll timeout when auto-poll is set, default - 3000ms. - -See also bindings/arm/primecell.txt - -Example: - -uart@80120000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x80120000 0x1000>; - interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dma 13 0 0x2>, <&dma 13 0 0x0>; - dma-names = "rx", "tx"; - clocks = <&foo_clk>, <&bar_clk>; - clock-names = "uartclk", "apb_pclk"; -}; diff --git a/Documentation/devicetree/bindings/serial/pl011.yaml b/Documentation/devicetree/bindings/serial/pl011.yaml new file mode 100644 index 000000000000..1a64d59152aa --- /dev/null +++ b/Documentation/devicetree/bindings/serial/pl011.yaml @@ -0,0 +1,126 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/pl011.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM AMBA Primecell PL011 serial UART + +maintainers: + - Rob Herring <robh@kernel.org> + +allOf: + - $ref: /schemas/serial.yaml# + +# Need a custom select here or 'arm,primecell' will match on lots of nodes +select: + properties: + compatible: + contains: + enum: + - arm,pl011 + - zte,zx296702-uart + required: + - compatible + +properties: + compatible: + oneOf: + - items: + - const: arm,pl011 + - const: arm,primecell + - items: + - const: zte,zx296702-uart + - const: arm,primecell + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + pinctrl-0: true + pinctrl-1: true + + pinctrl-names: + description: + When present, must have one state named "default", + and may contain a second name named "sleep". The former + state sets up pins for ordinary operation whereas + the latter state will put the associated pins to sleep + when the UART is unused + minItems: 1 + items: + - const: default + - const: sleep + + clocks: + description: + When present, the first clock listed must correspond to + the clock named UARTCLK on the IP block, i.e. the clock + to the external serial line, whereas the second clock + must correspond to the PCLK clocking the internal logic + of the block. Just listing one clock (the first one) is + deprecated. + maxItems: 2 + + clock-names: + items: + - const: uartclk + - const: apb_pclk + + dmas: + minItems: 1 + maxItems: 2 + + dma-names: + minItems: 1 + items: + - const: rx + - const: tx + + auto-poll: + description: + Enables polling when using RX DMA. + type: boolean + + poll-rate-ms: + description: + Rate at which poll occurs when auto-poll is set. + default 100ms. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - default: 100 + + poll-timeout-ms: + description: + Poll timeout when auto-poll is set, default + 3000ms. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - default: 3000 + +required: + - compatible + - reg + - interrupts + +dependencies: + poll-rate-ms: [ auto-poll ] + poll-timeout-ms: [ auto-poll ] + +additionalProperties: false + +examples: + - | + serial@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 4>; + dmas = <&dma 13 0 0x2>, <&dma 13 0 0x0>; + dma-names = "rx", "tx"; + clocks = <&foo_clk>, <&bar_clk>; + clock-names = "uartclk", "apb_pclk"; + }; + +... diff --git a/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt b/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt deleted file mode 100644 index 8b9e0d4dc2e4..000000000000 --- a/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt +++ /dev/null @@ -1,10 +0,0 @@ -Renesas RZ/N1 UART - -This controller is based on the Synopsys DesignWare ABP UART and inherits all -properties defined in snps-dw-apb-uart.txt except for the compatible property. - -Required properties: -- compatible : The device specific string followed by the generic RZ/N1 string. - Therefore it must be one of: - "renesas,r9a06g032-uart", "renesas,rzn1-uart" - "renesas,r9a06g033-uart", "renesas,rzn1-uart" diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 20232ad05d89..dd63151dc8b6 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -29,7 +29,9 @@ Required properties: - "renesas,scif-r8a774c0" for R8A774C0 (RZ/G2E) SCIF compatible UART. - "renesas,hscif-r8a774c0" for R8A774C0 (RZ/G2E) HSCIF compatible UART. - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. + - "renesas,hscif-r8a7778" for R8A7778 (R-Car M1) HSCIF compatible UART. - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. + - "renesas,hscif-r8a7779" for R8A7779 (R-Car H1) HSCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. - "renesas,scifa-r8a7790" for R8A7790 (R-Car H2) SCIFA compatible UART. - "renesas,scifb-r8a7790" for R8A7790 (R-Car H2) SCIFB compatible UART. diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt deleted file mode 100644 index 12bbe9f22560..000000000000 --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt +++ /dev/null @@ -1,76 +0,0 @@ -* Synopsys DesignWare ABP UART - -Required properties: -- compatible : "snps,dw-apb-uart" -- reg : offset and length of the register set for the device. -- interrupts : should contain uart interrupt. - -Clock handling: -The clock rate of the input clock needs to be supplied by one of -- clock-frequency : the input clock frequency for the UART. -- clocks : phandle to the input clock - -The supplying peripheral clock can also be handled, needing a second property -- clock-names: tuple listing input clock names. - Required elements: "baudclk", "apb_pclk" - -Optional properties: -- snps,uart-16550-compatible : reflects the value of UART_16550_COMPATIBLE - configuration parameter. Define this if your UART does not implement the busy - functionality. -- resets : phandle to the parent reset controller. -- reg-shift : quantity to shift the register offsets by. If this property is - not present then the register offsets are not shifted. -- reg-io-width : the size (in bytes) of the IO accesses that should be - performed on the device. If this property is not present then single byte - accesses are used. -- dcd-override : Override the DCD modem status signal. This signal will always - be reported as active instead of being obtained from the modem status - register. Define this if your serial port does not use this pin. -- dsr-override : Override the DTS modem status signal. This signal will always - be reported as active instead of being obtained from the modem status - register. Define this if your serial port does not use this pin. -- cts-override : Override the CTS modem status signal. This signal will always - be reported as active instead of being obtained from the modem status - register. Define this if your serial port does not use this pin. -- ri-override : Override the RI modem status signal. This signal will always be - reported as inactive instead of being obtained from the modem status register. - Define this if your serial port does not use this pin. - -Example: - - uart@80230000 { - compatible = "snps,dw-apb-uart"; - reg = <0x80230000 0x100>; - clock-frequency = <3686400>; - interrupts = <10>; - reg-shift = <2>; - reg-io-width = <4>; - dcd-override; - dsr-override; - cts-override; - ri-override; - }; - -Example with one clock: - - uart@80230000 { - compatible = "snps,dw-apb-uart"; - reg = <0x80230000 0x100>; - clocks = <&baudclk>; - interrupts = <10>; - reg-shift = <2>; - reg-io-width = <4>; - }; - -Example with two clocks: - - uart@80230000 { - compatible = "snps,dw-apb-uart"; - reg = <0x80230000 0x100>; - clocks = <&baudclk>, <&apb_pclk>; - clock-names = "baudclk", "apb_pclk"; - interrupts = <10>; - reg-shift = <2>; - reg-io-width = <4>; - }; diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml new file mode 100644 index 000000000000..b42002542690 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml @@ -0,0 +1,140 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/snps-dw-apb-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare ABP UART + +maintainers: + - Rob Herring <robh@kernel.org> + +allOf: + - $ref: /schemas/serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,r9a06g032-uart + - renesas,r9a06g033-uart + - const: renesas,rzn1-uart + - items: + - enum: + - rockchip,px30-uart + - rockchip,rk3036-uart + - rockchip,rk3066-uart + - rockchip,rk3188-uart + - rockchip,rk3288-uart + - rockchip,rk3328-uart + - rockchip,rk3368-uart + - rockchip,rk3399-uart + - rockchip,rv1108-uart + - const: snps,dw-apb-uart + - items: + - enum: + - brcm,bcm11351-dw-apb-uart + - brcm,bcm21664-dw-apb-uart + - const: snps,dw-apb-uart + - const: snps,dw-apb-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clock-frequency: true + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + items: + - const: baudclk + - const: apb_pclk + + snps,uart-16550-compatible: + description: reflects the value of UART_16550_COMPATIBLE configuration + parameter. Define this if your UART does not implement the busy functionality. + type: boolean + + resets: + maxItems: 1 + + reg-shift: true + + reg-io-width: true + + dcd-override: + description: Override the DCD modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + dsr-override: + description: Override the DTS modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + cts-override: + description: Override the CTS modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + ri-override: + description: Override the RI modem status signal. This signal will always + be reported as inactive instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. + type: boolean + +required: + - compatible + - reg + - interrupts + +examples: + - | + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clock-frequency = <3686400>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + dcd-override; + dsr-override; + cts-override; + ri-override; + }; + + - | + // Example with one clock: + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; + + - | + // Example with two clocks: + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>, <&apb_pclk>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; +... diff --git a/drivers/tty/Kconfig b/drivers/tty/Kconfig index 0840d27381ea..e0a04bfc873e 100644 --- a/drivers/tty/Kconfig +++ b/drivers/tty/Kconfig @@ -441,4 +441,28 @@ config VCC depends on SUN_LDOMS help Support for Sun logical domain consoles. + +config LDISC_AUTOLOAD + bool "Automatically load TTY Line Disciplines" + default y + help + Historically the kernel has always automatically loaded any + line discipline that is in a kernel module when a user asks + for it to be loaded with the TIOCSETD ioctl, or through other + means. This is not always the best thing to do on systems + where you know you will not be using some of the more + "ancient" line disciplines, so prevent the kernel from doing + this unless the request is coming from a process with the + CAP_SYS_MODULE permissions. + + Say 'Y' here if you trust your userspace users to do the right + thing, or if you have only provided the line disciplines that + you know you will be using, or if you wish to continue to use + the traditional method of on-demand loading of these modules + by any user. + + This functionality can be changed at runtime with the + dev.tty.ldisc_autoload sysctl, this configuration option will + only set the default value of this functionality. + endif # TTY diff --git a/drivers/tty/hvc/hvc_xen.c b/drivers/tty/hvc/hvc_xen.c index dc43fa96c3de..5ef08905fe05 100644 --- a/drivers/tty/hvc/hvc_xen.c +++ b/drivers/tty/hvc/hvc_xen.c @@ -492,7 +492,7 @@ static void xencons_backend_changed(struct xenbus_device *dev, case XenbusStateClosed: if (dev->state == XenbusStateClosed) break; - /* Missed the backend's CLOSING state -- fallthrough */ + /* fall through - Missed the backend's CLOSING state. */ case XenbusStateClosing: xenbus_frontend_closed(dev); break; diff --git a/drivers/tty/ipwireless/hardware.c b/drivers/tty/ipwireless/hardware.c index b0baa4ce10f9..6bbf35682d53 100644 --- a/drivers/tty/ipwireless/hardware.c +++ b/drivers/tty/ipwireless/hardware.c @@ -1516,6 +1516,8 @@ static void ipw_send_setup_packet(struct ipw_hardware *hw) sizeof(struct ipw_setup_get_version_query_packet), ADDR_SETUP_PROT, TL_PROTOCOLID_SETUP, TL_SETUP_SIGNO_GET_VERSION_QRY); + if (!ver_packet) + return; ver_packet->header.length = sizeof(struct tl_setup_get_version_qry); /* diff --git a/drivers/tty/n_gsm.c b/drivers/tty/n_gsm.c index 6f7da9a9d76f..c4e16b31f9ab 100644 --- a/drivers/tty/n_gsm.c +++ b/drivers/tty/n_gsm.c @@ -143,8 +143,8 @@ struct gsm_dlci { struct sk_buff *skb; /* Frame being sent */ struct sk_buff_head skb_list; /* Queued frames */ /* Data handling callback */ - void (*data)(struct gsm_dlci *dlci, u8 *data, int len); - void (*prev_data)(struct gsm_dlci *dlci, u8 *data, int len); + void (*data)(struct gsm_dlci *dlci, const u8 *data, int len); + void (*prev_data)(struct gsm_dlci *dlci, const u8 *data, int len); struct net_device *net; /* network interface, if created */ }; @@ -988,7 +988,7 @@ static void gsm_dlci_data_kick(struct gsm_dlci *dlci) * Encode up and queue a UI/UIH frame containing our response. */ -static void gsm_control_reply(struct gsm_mux *gsm, int cmd, u8 *data, +static void gsm_control_reply(struct gsm_mux *gsm, int cmd, const u8 *data, int dlen) { struct gsm_msg *msg; @@ -1073,14 +1073,14 @@ static void gsm_process_modem(struct tty_struct *tty, struct gsm_dlci *dlci, * and if need be stuff a break message down the tty. */ -static void gsm_control_modem(struct gsm_mux *gsm, u8 *data, int clen) +static void gsm_control_modem(struct gsm_mux *gsm, const u8 *data, int clen) { unsigned int addr = 0; unsigned int modem = 0; unsigned int brk = 0; struct gsm_dlci *dlci; int len = clen; - u8 *dp = data; + const u8 *dp = data; struct tty_struct *tty; while (gsm_read_ea(&addr, *dp++) == 0) { @@ -1134,13 +1134,13 @@ static void gsm_control_modem(struct gsm_mux *gsm, u8 *data, int clen) * this into the uplink tty if present */ -static void gsm_control_rls(struct gsm_mux *gsm, u8 *data, int clen) +static void gsm_control_rls(struct gsm_mux *gsm, const u8 *data, int clen) { struct tty_port *port; unsigned int addr = 0; u8 bits; int len = clen; - u8 *dp = data; + const u8 *dp = data; while (gsm_read_ea(&addr, *dp++) == 0) { len--; @@ -1189,7 +1189,7 @@ static void gsm_dlci_begin_close(struct gsm_dlci *dlci); */ static void gsm_control_message(struct gsm_mux *gsm, unsigned int command, - u8 *data, int clen) + const u8 *data, int clen) { u8 buf[1]; unsigned long flags; @@ -1261,7 +1261,7 @@ static void gsm_control_message(struct gsm_mux *gsm, unsigned int command, */ static void gsm_control_response(struct gsm_mux *gsm, unsigned int command, - u8 *data, int clen) + const u8 *data, int clen) { struct gsm_control *ctrl; unsigned long flags; @@ -1553,7 +1553,7 @@ static void gsm_dlci_begin_close(struct gsm_dlci *dlci) * open we shovel the bits down it, if not we drop them. */ -static void gsm_dlci_data(struct gsm_dlci *dlci, u8 *data, int clen) +static void gsm_dlci_data(struct gsm_dlci *dlci, const u8 *data, int clen) { /* krefs .. */ struct tty_port *port = &dlci->port; @@ -1565,14 +1565,11 @@ static void gsm_dlci_data(struct gsm_dlci *dlci, u8 *data, int clen) pr_debug("%d bytes for tty\n", len); switch (dlci->adaption) { /* Unsupported types */ - /* Packetised interruptible data */ - case 4: + case 4: /* Packetised interruptible data */ break; - /* Packetised uininterruptible voice/data */ - case 3: + case 3: /* Packetised uininterruptible voice/data */ break; - /* Asynchronous serial with line state in each frame */ - case 2: + case 2: /* Asynchronous serial with line state in each frame */ while (gsm_read_ea(&modem, *data++) == 0) { len--; if (len == 0) @@ -1583,8 +1580,8 @@ static void gsm_dlci_data(struct gsm_dlci *dlci, u8 *data, int clen) gsm_process_modem(tty, dlci, modem, clen); tty_kref_put(tty); } - /* Line state will go via DLCI 0 controls only */ - case 1: + /* Fall through */ + case 1: /* Line state will go via DLCI 0 controls only */ default: tty_insert_flip_string(port, data, len); tty_flip_buffer_push(port); @@ -1603,7 +1600,7 @@ static void gsm_dlci_data(struct gsm_dlci *dlci, u8 *data, int clen) * and we divide up the work accordingly. */ -static void gsm_dlci_command(struct gsm_dlci *dlci, u8 *data, int len) +static void gsm_dlci_command(struct gsm_dlci *dlci, const u8 *data, int len) { /* See what command is involved */ unsigned int command = 0; @@ -1979,7 +1976,7 @@ static void gsm1_receive(struct gsm_mux *gsm, unsigned char c) gsm->address = 0; gsm->state = GSM_ADDRESS; gsm->fcs = INIT_FCS; - /* Drop through */ + /* Fall through */ case GSM_ADDRESS: /* Address continuation */ gsm->fcs = gsm_fcs_add(gsm->fcs, c); if (gsm_read_ea(&gsm->address, c)) @@ -2214,6 +2211,111 @@ static struct gsm_mux *gsm_alloc_mux(void) return gsm; } +static void gsm_copy_config_values(struct gsm_mux *gsm, + struct gsm_config *c) +{ + memset(c, 0, sizeof(*c)); + c->adaption = gsm->adaption; + c->encapsulation = gsm->encoding; + c->initiator = gsm->initiator; + c->t1 = gsm->t1; + c->t2 = gsm->t2; + c->t3 = 0; /* Not supported */ + c->n2 = gsm->n2; + if (gsm->ftype == UIH) + c->i = 1; + else + c->i = 2; + pr_debug("Ftype %d i %d\n", gsm->ftype, c->i); + c->mru = gsm->mru; + c->mtu = gsm->mtu; + c->k = 0; +} + +static int gsm_config(struct gsm_mux *gsm, struct gsm_config *c) +{ + int need_close = 0; + int need_restart = 0; + + /* Stuff we don't support yet - UI or I frame transport, windowing */ + if ((c->adaption != 1 && c->adaption != 2) || c->k) + return -EOPNOTSUPP; + /* Check the MRU/MTU range looks sane */ + if (c->mru > MAX_MRU || c->mtu > MAX_MTU || c->mru < 8 || c->mtu < 8) + return -EINVAL; + if (c->n2 < 3) + return -EINVAL; + if (c->encapsulation > 1) /* Basic, advanced, no I */ + return -EINVAL; + if (c->initiator > 1) + return -EINVAL; + if (c->i == 0 || c->i > 2) /* UIH and UI only */ + return -EINVAL; + /* + * See what is needed for reconfiguration + */ + + /* Timing fields */ + if (c->t1 != 0 && c->t1 != gsm->t1) + need_restart = 1; + if (c->t2 != 0 && c->t2 != gsm->t2) + need_restart = 1; + if (c->encapsulation != gsm->encoding) + need_restart = 1; + if (c->adaption != gsm->adaption) + need_restart = 1; + /* Requires care */ + if (c->initiator != gsm->initiator) + need_close = 1; + if (c->mru != gsm->mru) + need_restart = 1; + if (c->mtu != gsm->mtu) + need_restart = 1; + + /* + * Close down what is needed, restart and initiate the new + * configuration + */ + + if (need_close || need_restart) { + int ret; + + ret = gsm_disconnect(gsm); + + if (ret) + return ret; + } + if (need_restart) + gsm_cleanup_mux(gsm); + + gsm->initiator = c->initiator; + gsm->mru = c->mru; + gsm->mtu = c->mtu; + gsm->encoding = c->encapsulation; + gsm->adaption = c->adaption; + gsm->n2 = c->n2; + + if (c->i == 1) + gsm->ftype = UIH; + else if (c->i == 2) + gsm->ftype = UI; + + if (c->t1) + gsm->t1 = c->t1; + if (c->t2) + gsm->t2 = c->t2; + + /* + * FIXME: We need to separate activation/deactivation from adding + * and removing from the mux array + */ + if (need_restart) + gsm_activate_mux(gsm); + if (gsm->initiator && need_close) + gsm_dlci_begin_open(gsm->dlci[0]); + return 0; +} + /** * gsmld_output - write to link * @gsm: our mux @@ -2495,89 +2597,6 @@ static __poll_t gsmld_poll(struct tty_struct *tty, struct file *file, return mask; } -static int gsmld_config(struct tty_struct *tty, struct gsm_mux *gsm, - struct gsm_config *c) -{ - int need_close = 0; - int need_restart = 0; - - /* Stuff we don't support yet - UI or I frame transport, windowing */ - if ((c->adaption != 1 && c->adaption != 2) || c->k) - return -EOPNOTSUPP; - /* Check the MRU/MTU range looks sane */ - if (c->mru > MAX_MRU || c->mtu > MAX_MTU || c->mru < 8 || c->mtu < 8) - return -EINVAL; - if (c->n2 < 3) - return -EINVAL; - if (c->encapsulation > 1) /* Basic, advanced, no I */ - return -EINVAL; - if (c->initiator > 1) - return -EINVAL; - if (c->i == 0 || c->i > 2) /* UIH and UI only */ - return -EINVAL; - /* - * See what is needed for reconfiguration - */ - - /* Timing fields */ - if (c->t1 != 0 && c->t1 != gsm->t1) - need_restart = 1; - if (c->t2 != 0 && c->t2 != gsm->t2) - need_restart = 1; - if (c->encapsulation != gsm->encoding) - need_restart = 1; - if (c->adaption != gsm->adaption) - need_restart = 1; - /* Requires care */ - if (c->initiator != gsm->initiator) - need_close = 1; - if (c->mru != gsm->mru) - need_restart = 1; - if (c->mtu != gsm->mtu) - need_restart = 1; - - /* - * Close down what is needed, restart and initiate the new - * configuration - */ - - if (need_close || need_restart) { - int ret; - - ret = gsm_disconnect(gsm); - - if (ret) - return ret; - } - if (need_restart) - gsm_cleanup_mux(gsm); - - gsm->initiator = c->initiator; - gsm->mru = c->mru; - gsm->mtu = c->mtu; - gsm->encoding = c->encapsulation; - gsm->adaption = c->adaption; - gsm->n2 = c->n2; - - if (c->i == 1) - gsm->ftype = UIH; - else if (c->i == 2) - gsm->ftype = UI; - - if (c->t1) - gsm->t1 = c->t1; - if (c->t2) - gsm->t2 = c->t2; - - /* FIXME: We need to separate activation/deactivation from adding - and removing from the mux array */ - if (need_restart) - gsm_activate_mux(gsm); - if (gsm->initiator && need_close) - gsm_dlci_begin_open(gsm->dlci[0]); - return 0; -} - static int gsmld_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg) { @@ -2586,29 +2605,14 @@ static int gsmld_ioctl(struct tty_struct *tty, struct file *file, switch (cmd) { case GSMIOC_GETCONF: - memset(&c, 0, sizeof(c)); - c.adaption = gsm->adaption; - c.encapsulation = gsm->encoding; - c.initiator = gsm->initiator; - c.t1 = gsm->t1; - c.t2 = gsm->t2; - c.t3 = 0; /* Not supported */ - c.n2 = gsm->n2; - if (gsm->ftype == UIH) - c.i = 1; - else - c.i = 2; - pr_debug("Ftype %d i %d\n", gsm->ftype, c.i); - c.mru = gsm->mru; - c.mtu = gsm->mtu; - c.k = 0; + gsm_copy_config_values(gsm, &c); if (copy_to_user((void *)arg, &c, sizeof(c))) return -EFAULT; return 0; case GSMIOC_SETCONF: if (copy_from_user(&c, (void *)arg, sizeof(c))) return -EFAULT; - return gsmld_config(tty, gsm, &c); + return gsm_config(gsm, &c); default: return n_tty_ioctl_helper(tty, file, cmd, arg); } @@ -2695,7 +2699,7 @@ static void gsm_mux_net_tx_timeout(struct net_device *net) } static void gsm_mux_rx_netchar(struct gsm_dlci *dlci, - unsigned char *in_buf, int size) + const unsigned char *in_buf, int size) { struct net_device *net = dlci->net; struct sk_buff *skb; diff --git a/drivers/tty/n_hdlc.c b/drivers/tty/n_hdlc.c index 8bdf42bc8fc8..e55c79eb6430 100644 --- a/drivers/tty/n_hdlc.c +++ b/drivers/tty/n_hdlc.c @@ -777,7 +777,7 @@ static int n_hdlc_tty_ioctl(struct tty_struct *tty, struct file *file, case TCOFLUSH: flush_tx_queue(tty); } - /* fall through to default */ + /* fall through - to default */ default: error = n_tty_ioctl_helper(tty, file, cmd, arg); diff --git a/drivers/tty/n_tty.c b/drivers/tty/n_tty.c index 5dc9686697cf..9cdb0fa3c4bf 100644 --- a/drivers/tty/n_tty.c +++ b/drivers/tty/n_tty.c @@ -50,8 +50,10 @@ #include <linux/ratelimit.h> #include <linux/vmalloc.h> - -/* number of characters left in xmit buffer before select has we have room */ +/* + * Until this number of characters is queued in the xmit buffer, select will + * return "we have room for writes". + */ #define WAKEUP_CHARS 256 /* diff --git a/drivers/tty/nozomi.c b/drivers/tty/nozomi.c index fed820e9ab9d..3214e22e79f3 100644 --- a/drivers/tty/nozomi.c +++ b/drivers/tty/nozomi.c @@ -1317,7 +1317,6 @@ static void remove_sysfs_files(struct nozomi *dc) static int nozomi_card_init(struct pci_dev *pdev, const struct pci_device_id *ent) { - resource_size_t start; int ret; struct nozomi *dc = NULL; int ndev_idx; @@ -1357,17 +1356,10 @@ static int nozomi_card_init(struct pci_dev *pdev, goto err_disable_device; } - start = pci_resource_start(dc->pdev, 0); - if (start == 0) { - dev_err(&pdev->dev, "No I/O address for card detected\n"); - ret = -ENODEV; - goto err_rel_regs; - } - /* Find out what card type it is */ nozomi_get_card_type(dc); - dc->base_addr = ioremap_nocache(start, dc->card_type); + dc->base_addr = pci_iomap(dc->pdev, 0, dc->card_type); if (!dc->base_addr) { dev_err(&pdev->dev, "Unable to map card MMIO\n"); ret = -ENODEV; diff --git a/drivers/tty/serdev/serdev-ttyport.c b/drivers/tty/serdev/serdev-ttyport.c index fa1672993b4c..d1cdd2ab8b4c 100644 --- a/drivers/tty/serdev/serdev-ttyport.c +++ b/drivers/tty/serdev/serdev-ttyport.c @@ -233,7 +233,7 @@ static int ttyport_get_tiocm(struct serdev_controller *ctrl) if (!tty->ops->tiocmget) return -ENOTSUPP; - return tty->driver->ops->tiocmget(tty); + return tty->ops->tiocmget(tty); } static int ttyport_set_tiocm(struct serdev_controller *ctrl, unsigned int set, unsigned int clear) @@ -244,7 +244,7 @@ static int ttyport_set_tiocm(struct serdev_controller *ctrl, unsigned int set, u if (!tty->ops->tiocmset) return -ENOTSUPP; - return tty->driver->ops->tiocmset(tty, set, clear); + return tty->ops->tiocmset(tty, set, clear); } static const struct serdev_controller_ops ctrl_ops = { diff --git a/drivers/tty/serial/8250/8250_ingenic.c b/drivers/tty/serial/8250/8250_ingenic.c index 15a8c8dfa92b..424c07c5f629 100644 --- a/drivers/tty/serial/8250/8250_ingenic.c +++ b/drivers/tty/serial/8250/8250_ingenic.c @@ -129,22 +129,21 @@ static int __init ingenic_early_console_setup(struct earlycon_device *dev, return 0; } -EARLYCON_DECLARE(jz4740_uart, ingenic_early_console_setup); OF_EARLYCON_DECLARE(jz4740_uart, "ingenic,jz4740-uart", ingenic_early_console_setup); -EARLYCON_DECLARE(jz4770_uart, ingenic_early_console_setup); OF_EARLYCON_DECLARE(jz4770_uart, "ingenic,jz4770-uart", ingenic_early_console_setup); -EARLYCON_DECLARE(jz4775_uart, ingenic_early_console_setup); OF_EARLYCON_DECLARE(jz4775_uart, "ingenic,jz4775-uart", ingenic_early_console_setup); -EARLYCON_DECLARE(jz4780_uart, ingenic_early_console_setup); OF_EARLYCON_DECLARE(jz4780_uart, "ingenic,jz4780-uart", ingenic_early_console_setup); +OF_EARLYCON_DECLARE(x1000_uart, "ingenic,x1000-uart", + ingenic_early_console_setup); + static void ingenic_uart_serial_out(struct uart_port *p, int offset, int value) { int ier; @@ -328,12 +327,18 @@ static const struct ingenic_uart_config jz4780_uart_config = { .fifosize = 64, }; +static const struct ingenic_uart_config x1000_uart_config = { + .tx_loadsz = 32, + .fifosize = 64, +}; + static const struct of_device_id of_match[] = { { .compatible = "ingenic,jz4740-uart", .data = &jz4740_uart_config }, { .compatible = "ingenic,jz4760-uart", .data = &jz4760_uart_config }, { .compatible = "ingenic,jz4770-uart", .data = &jz4760_uart_config }, { .compatible = "ingenic,jz4775-uart", .data = &jz4760_uart_config }, { .compatible = "ingenic,jz4780-uart", .data = &jz4780_uart_config }, + { .compatible = "ingenic,x1000-uart", .data = &x1000_uart_config }, { /* sentinel */ } }; MODULE_DEVICE_TABLE(of, of_match); diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c index a1a85805d010..0277479c87e9 100644 --- a/drivers/tty/serial/8250/8250_of.c +++ b/drivers/tty/serial/8250/8250_of.c @@ -130,6 +130,10 @@ static int of_platform_serial_setup(struct platform_device *ofdev, port->flags |= UPF_IOREMAP; } + /* Compatibility with the deprecated pxa driver and 8250_pxa drivers. */ + if (of_device_is_compatible(np, "mrvl,mmp-uart")) + port->regshift = 2; + /* Check for registers offset within the devices address range */ if (of_property_read_u32(np, "reg-shift", &prop) == 0) port->regshift = prop; @@ -327,6 +331,7 @@ static const struct of_device_id of_platform_serial_table[] = { { .compatible = "nvidia,tegra20-uart", .data = (void *)PORT_TEGRA, }, { .compatible = "nxp,lpc3220-uart", .data = (void *)PORT_LPC3220, }, { .compatible = "ralink,rt2880-uart", .data = (void *)PORT_RT2880, }, + { .compatible = "intel,xscale-uart", .data = (void *)PORT_XSCALE, }, { .compatible = "altr,16550-FIFO32", .data = (void *)PORT_ALTR_16550_F32, }, { .compatible = "altr,16550-FIFO64", diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c index ad7ba7d0f28d..0a8316632d75 100644 --- a/drivers/tty/serial/8250/8250_omap.c +++ b/drivers/tty/serial/8250/8250_omap.c @@ -12,6 +12,7 @@ #define SUPPORT_SYSRQ #endif +#include <linux/clk.h> #include <linux/device.h> #include <linux/io.h> #include <linux/module.h> @@ -1134,10 +1135,12 @@ static int omap8250_probe(struct platform_device *pdev) { struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + struct device_node *np = pdev->dev.of_node; struct omap8250_priv *priv; struct uart_8250_port up; int ret; void __iomem *membase; + const struct of_device_id *id; if (!regs || !irq) { dev_err(&pdev->dev, "missing registers or irq\n"); @@ -1194,27 +1197,31 @@ static int omap8250_probe(struct platform_device *pdev) up.port.unthrottle = omap_8250_unthrottle; up.port.rs485_config = omap_8250_rs485_config; - if (pdev->dev.of_node) { - const struct of_device_id *id; - - ret = of_alias_get_id(pdev->dev.of_node, "serial"); - - of_property_read_u32(pdev->dev.of_node, "clock-frequency", - &up.port.uartclk); - priv->wakeirq = irq_of_parse_and_map(pdev->dev.of_node, 1); - - id = of_match_device(of_match_ptr(omap8250_dt_ids), &pdev->dev); - if (id && id->data) - priv->habit |= *(u8 *)id->data; - } else { - ret = pdev->id; - } + ret = of_alias_get_id(np, "serial"); if (ret < 0) { - dev_err(&pdev->dev, "failed to get alias/pdev id\n"); + dev_err(&pdev->dev, "failed to get alias\n"); return ret; } up.port.line = ret; + if (of_property_read_u32(np, "clock-frequency", &up.port.uartclk)) { + struct clk *clk; + + clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(clk)) { + if (PTR_ERR(clk) == -EPROBE_DEFER) + return -EPROBE_DEFER; + } else { + up.port.uartclk = clk_get_rate(clk); + } + } + + priv->wakeirq = irq_of_parse_and_map(np, 1); + + id = of_match_device(of_match_ptr(omap8250_dt_ids), &pdev->dev); + if (id && id->data) + priv->habit |= *(u8 *)id->data; + if (!up.port.uartclk) { up.port.uartclk = DEFAULT_CLK_SPEED; dev_warn(&pdev->dev, @@ -1242,25 +1249,23 @@ static int omap8250_probe(struct platform_device *pdev) omap_serial_fill_features_erratas(&up, priv); up.port.handle_irq = omap8250_no_handle_irq; #ifdef CONFIG_SERIAL_8250_DMA - if (pdev->dev.of_node) { - /* - * Oh DMA support. If there are no DMA properties in the DT then - * we will fall back to a generic DMA channel which does not - * really work here. To ensure that we do not get a generic DMA - * channel assigned, we have the the_no_dma_filter_fn() here. - * To avoid "failed to request DMA" messages we check for DMA - * properties in DT. - */ - ret = of_property_count_strings(pdev->dev.of_node, "dma-names"); - if (ret == 2) { - up.dma = &priv->omap8250_dma; - priv->omap8250_dma.fn = the_no_dma_filter_fn; - priv->omap8250_dma.tx_dma = omap_8250_tx_dma; - priv->omap8250_dma.rx_dma = omap_8250_rx_dma; - priv->omap8250_dma.rx_size = RX_TRIGGER; - priv->omap8250_dma.rxconf.src_maxburst = RX_TRIGGER; - priv->omap8250_dma.txconf.dst_maxburst = TX_TRIGGER; - } + /* + * Oh DMA support. If there are no DMA properties in the DT then + * we will fall back to a generic DMA channel which does not + * really work here. To ensure that we do not get a generic DMA + * channel assigned, we have the the_no_dma_filter_fn() here. + * To avoid "failed to request DMA" messages we check for DMA + * properties in DT. + */ + ret = of_property_count_strings(np, "dma-names"); + if (ret == 2) { + up.dma = &priv->omap8250_dma; + priv->omap8250_dma.fn = the_no_dma_filter_fn; + priv->omap8250_dma.tx_dma = omap_8250_tx_dma; + priv->omap8250_dma.rx_dma = omap_8250_rx_dma; + priv->omap8250_dma.rx_size = RX_TRIGGER; + priv->omap8250_dma.rxconf.src_maxburst = RX_TRIGGER; + priv->omap8250_dma.txconf.dst_maxburst = TX_TRIGGER; } #endif ret = serial8250_register_8250_port(&up); diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 48bd694a5fa1..df41397de478 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -2027,6 +2027,111 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { .setup = pci_default_setup, .exit = pci_plx9050_exit, }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SDB, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_MPCIE_COM_4S, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4DB, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_MPCIE_COM232_4, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SMDB, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_MPCIE_COM_4SM, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM422_4, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM485_4, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S, + .device = PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM232_4, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM422_4, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM485_4, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SM, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4SM, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, /* * SBS Technologies, Inc., PMC-OCTALPRO 232 */ @@ -3375,6 +3480,9 @@ static const struct pci_device_id blacklist[] = { /* Exar devices */ { PCI_VDEVICE(EXAR, PCI_ANY_ID), }, { PCI_VDEVICE(COMMTECH, PCI_ANY_ID), }, + + /* End of the black list */ + { } }; static int serial_pci_is_class_communication(struct pci_dev *dev) @@ -3392,25 +3500,6 @@ static int serial_pci_is_class_communication(struct pci_dev *dev) return 0; } -static int serial_pci_is_blacklisted(struct pci_dev *dev) -{ - const struct pci_device_id *bldev; - - /* - * Do not access blacklisted devices that are known not to - * feature serial ports or are handled by other modules. - */ - for (bldev = blacklist; - bldev < blacklist + ARRAY_SIZE(blacklist); - bldev++) { - if (dev->vendor == bldev->vendor && - dev->device == bldev->device) - return -ENODEV; - } - - return 0; -} - /* * Given a complete unknown PCI device, try to use some heuristics to * guess what the configuration might be, based on the pitiful PCI @@ -3634,6 +3723,7 @@ pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent) struct pci_serial_quirk *quirk; struct serial_private *priv; const struct pciserial_board *board; + const struct pci_device_id *exclude; struct pciserial_board tmp; int rc; @@ -3652,9 +3742,9 @@ pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent) board = &pci_boards[ent->driver_data]; - rc = serial_pci_is_blacklisted(dev); - if (rc) - return rc; + exclude = pci_match_id(blacklist, dev); + if (exclude) + return -ENODEV; rc = pcim_enable_device(dev); pci_save_state(dev); @@ -4575,10 +4665,10 @@ static const struct pci_device_id serial_pci_tbl[] = { */ { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_2SDB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_COM_2S, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SDB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_pericom_PI7C9X7954 }, @@ -4587,10 +4677,10 @@ static const struct pci_device_id serial_pci_tbl[] = { pbn_pericom_PI7C9X7954 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM232_2DB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_COM232_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4DB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_pericom_PI7C9X7954 }, @@ -4599,10 +4689,10 @@ static const struct pci_device_id serial_pci_tbl[] = { pbn_pericom_PI7C9X7954 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_2SMDB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_COM_2SM, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SMDB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_pericom_PI7C9X7954 }, @@ -4611,13 +4701,13 @@ static const struct pci_device_id serial_pci_tbl[] = { pbn_pericom_PI7C9X7954 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_ICM485_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7951 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_ICM422_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_ICM485_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_ICM422_4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_pericom_PI7C9X7954 }, @@ -4626,16 +4716,16 @@ static const struct pci_device_id serial_pci_tbl[] = { pbn_pericom_PI7C9X7954 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM_2S, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_pericom_PI7C9X7954 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_ICM232_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_pericom_PI7C9X7954 }, @@ -4644,13 +4734,13 @@ static const struct pci_device_id serial_pci_tbl[] = { pbn_pericom_PI7C9X7954 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM_2SM, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7954 }, + pbn_pericom_PI7C9X7952 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM422_4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7958 }, + pbn_pericom_PI7C9X7954 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM485_4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7958 }, + pbn_pericom_PI7C9X7954 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM422_8, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_pericom_PI7C9X7958 }, @@ -4659,19 +4749,19 @@ static const struct pci_device_id serial_pci_tbl[] = { pbn_pericom_PI7C9X7958 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7958 }, + pbn_pericom_PI7C9X7954 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM232_8, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_pericom_PI7C9X7958 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SM, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7958 }, + pbn_pericom_PI7C9X7954 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_8SM, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_pericom_PI7C9X7958 }, { PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4SM, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pericom_PI7C9X7958 }, + pbn_pericom_PI7C9X7954 }, /* * Topic TP560 Data/Fax/Voice 56k modem (reported by Evan Clarke) */ diff --git a/drivers/tty/serial/8250/8250_pxa.c b/drivers/tty/serial/8250/8250_pxa.c index b9bcbe20a2be..c47188860e32 100644 --- a/drivers/tty/serial/8250/8250_pxa.c +++ b/drivers/tty/serial/8250/8250_pxa.c @@ -113,6 +113,10 @@ static int serial_pxa_probe(struct platform_device *pdev) if (ret) return ret; + ret = of_alias_get_id(pdev->dev.of_node, "serial"); + if (ret >= 0) + uart.port.line = ret; + uart.port.type = PORT_XSCALE; uart.port.iotype = UPIO_MEM32; uart.port.mapbase = mmres->start; diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 089a6f285d5e..72966bc0ac76 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -335,6 +335,28 @@ config SERIAL_TEGRA are enabled). This driver uses the APB DMA to achieve higher baudrate and better performance. +config SERIAL_TEGRA_TCU + tristate "NVIDIA Tegra Combined UART" + depends on ARCH_TEGRA && TEGRA_HSP_MBOX + select SERIAL_CORE + help + Support for the mailbox-based TCU (Tegra Combined UART) serial port. + TCU is a virtual serial port that allows multiplexing multiple data + streams into a single hardware serial port. + +config SERIAL_TEGRA_TCU_CONSOLE + bool "Support for console on a Tegra TCU serial port" + depends on SERIAL_TEGRA_TCU=y + select SERIAL_CORE_CONSOLE + default y + ---help--- + If you say Y here, it will be possible to use a the Tegra TCU as the + system console (the system console is the device which receives all + kernel messages and warnings and which allows logins in single user + mode). + + If unsure, say Y. + config SERIAL_MAX3100 tristate "MAX3100 support" depends on SPI diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index 1511e8a9f856..40b702aaa85e 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -77,6 +77,7 @@ obj-$(CONFIG_SERIAL_LANTIQ) += lantiq.o obj-$(CONFIG_SERIAL_XILINX_PS_UART) += xilinx_uartps.o obj-$(CONFIG_SERIAL_SIRFSOC) += sirfsoc_uart.o obj-$(CONFIG_SERIAL_TEGRA) += serial-tegra.o +obj-$(CONFIG_SERIAL_TEGRA_TCU) += tegra-tcu.o obj-$(CONFIG_SERIAL_AR933X) += ar933x_uart.o obj-$(CONFIG_SERIAL_EFM32_UART) += efm32-uart.o obj-$(CONFIG_SERIAL_ARC) += arc_uart.o diff --git a/drivers/tty/serial/clps711x.c b/drivers/tty/serial/clps711x.c index 98f193a83392..061590795680 100644 --- a/drivers/tty/serial/clps711x.c +++ b/drivers/tty/serial/clps711x.c @@ -442,14 +442,10 @@ static struct console clps711x_console = { static int uart_clps711x_probe(struct platform_device *pdev) { struct device_node *np = pdev->dev.of_node; - int ret, index = np ? of_alias_get_id(np, "serial") : pdev->id; struct clps711x_port *s; struct resource *res; struct clk *uart_clk; - int irq; - - if (index < 0 || index >= UART_CLPS711X_NR) - return -EINVAL; + int irq, ret; s = devm_kzalloc(&pdev->dev, sizeof(*s), GFP_KERNEL); if (!s) @@ -473,20 +469,11 @@ static int uart_clps711x_probe(struct platform_device *pdev) if (s->rx_irq < 0) return s->rx_irq; - if (!np) { - char syscon_name[9]; - - sprintf(syscon_name, "syscon.%i", index + 1); - s->syscon = syscon_regmap_lookup_by_pdevname(syscon_name); - if (IS_ERR(s->syscon)) - return PTR_ERR(s->syscon); - } else { - s->syscon = syscon_regmap_lookup_by_phandle(np, "syscon"); - if (IS_ERR(s->syscon)) - return PTR_ERR(s->syscon); - } + s->syscon = syscon_regmap_lookup_by_phandle(np, "syscon"); + if (IS_ERR(s->syscon)) + return PTR_ERR(s->syscon); - s->port.line = index; + s->port.line = of_alias_get_id(np, "serial"); s->port.dev = &pdev->dev; s->port.iotype = UPIO_MEM32; s->port.mapbase = res->start; diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c index debdd1b9e01a..ea1c85e3b432 100644 --- a/drivers/tty/serial/fsl_lpuart.c +++ b/drivers/tty/serial/fsl_lpuart.c @@ -426,6 +426,17 @@ static void lpuart_dma_tx_complete(void *arg) spin_unlock_irqrestore(&sport->port.lock, flags); } +static dma_addr_t lpuart_dma_datareg_addr(struct lpuart_port *sport) +{ + switch (sport->port.iotype) { + case UPIO_MEM32: + return sport->port.mapbase + UARTDATA; + case UPIO_MEM32BE: + return sport->port.mapbase + UARTDATA + sizeof(u32) - 1; + } + return sport->port.mapbase + UARTDR; +} + static int lpuart_dma_tx_request(struct uart_port *port) { struct lpuart_port *sport = container_of(port, @@ -433,7 +444,7 @@ static int lpuart_dma_tx_request(struct uart_port *port) struct dma_slave_config dma_tx_sconfig = {}; int ret; - dma_tx_sconfig.dst_addr = sport->port.mapbase + UARTDR; + dma_tx_sconfig.dst_addr = lpuart_dma_datareg_addr(sport); dma_tx_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; dma_tx_sconfig.dst_maxburst = 1; dma_tx_sconfig.direction = DMA_MEM_TO_DEV; @@ -636,13 +647,19 @@ static void lpuart_start_tx(struct uart_port *port) static void lpuart32_start_tx(struct uart_port *port) { struct lpuart_port *sport = container_of(port, struct lpuart_port, port); + struct circ_buf *xmit = &sport->port.state->xmit; unsigned long temp; - temp = lpuart32_read(port, UARTCTRL); - lpuart32_write(port, temp | UARTCTRL_TIE, UARTCTRL); + if (sport->lpuart_dma_tx_use) { + if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) + lpuart_dma_tx(sport); + } else { + temp = lpuart32_read(port, UARTCTRL); + lpuart32_write(port, temp | UARTCTRL_TIE, UARTCTRL); - if (lpuart32_read(port, UARTSTAT) & UARTSTAT_TDRE) - lpuart32_transmit_buffer(sport); + if (lpuart32_read(port, UARTSTAT) & UARTSTAT_TDRE) + lpuart32_transmit_buffer(sport); + } } /* return TIOCSER_TEMT when transmitter is not busy */ @@ -664,8 +681,18 @@ static unsigned int lpuart_tx_empty(struct uart_port *port) static unsigned int lpuart32_tx_empty(struct uart_port *port) { - return (lpuart32_read(port, UARTSTAT) & UARTSTAT_TC) ? - TIOCSER_TEMT : 0; + struct lpuart_port *sport = container_of(port, + struct lpuart_port, port); + unsigned long stat = lpuart32_read(port, UARTSTAT); + unsigned long sfifo = lpuart32_read(port, UARTFIFO); + + if (sport->dma_tx_in_progress) + return 0; + + if (stat & UARTSTAT_TC && sfifo & UARTFIFO_TXEMPT) + return TIOCSER_TEMT; + + return 0; } static bool lpuart_is_32(struct lpuart_port *sport) @@ -862,11 +889,10 @@ static irqreturn_t lpuart32_int(int irq, void *dev_id) rxcount = lpuart32_read(&sport->port, UARTWATER); rxcount = rxcount >> UARTWATER_RXCNT_OFF; - if (sts & UARTSTAT_RDRF || rxcount > 0) + if ((sts & UARTSTAT_RDRF || rxcount > 0) && !sport->lpuart_dma_rx_use) lpuart32_rxint(irq, dev_id); - if ((sts & UARTSTAT_TDRE) && - !(lpuart32_read(&sport->port, UARTBAUD) & UARTBAUD_TDMAE)) + if ((sts & UARTSTAT_TDRE) && !sport->lpuart_dma_tx_use) lpuart_txint(irq, dev_id); lpuart32_write(&sport->port, sts, UARTSTAT); @@ -881,18 +907,31 @@ static void lpuart_copy_rx_to_tty(struct lpuart_port *sport) struct circ_buf *ring = &sport->rx_ring; unsigned long flags; int count = 0; - unsigned char sr; - sr = readb(sport->port.membase + UARTSR1); + if (lpuart_is_32(sport)) { + unsigned long sr = lpuart32_read(&sport->port, UARTSTAT); - if (sr & (UARTSR1_PE | UARTSR1_FE)) { - /* Read DR to clear the error flags */ - readb(sport->port.membase + UARTDR); + if (sr & (UARTSTAT_PE | UARTSTAT_FE)) { + /* Read DR to clear the error flags */ + lpuart32_read(&sport->port, UARTDATA); + + if (sr & UARTSTAT_PE) + sport->port.icount.parity++; + else if (sr & UARTSTAT_FE) + sport->port.icount.frame++; + } + } else { + unsigned char sr = readb(sport->port.membase + UARTSR1); - if (sr & UARTSR1_PE) - sport->port.icount.parity++; - else if (sr & UARTSR1_FE) - sport->port.icount.frame++; + if (sr & (UARTSR1_PE | UARTSR1_FE)) { + /* Read DR to clear the error flags */ + readb(sport->port.membase + UARTDR); + + if (sr & UARTSR1_PE) + sport->port.icount.parity++; + else if (sr & UARTSR1_FE) + sport->port.icount.frame++; + } } async_tx_ack(sport->dma_rx_desc); @@ -1015,7 +1054,7 @@ static inline int lpuart_start_rx_dma(struct lpuart_port *sport) return -EINVAL; } - dma_rx_sconfig.src_addr = sport->port.mapbase + UARTDR; + dma_rx_sconfig.src_addr = lpuart_dma_datareg_addr(sport); dma_rx_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; dma_rx_sconfig.src_maxburst = 1; dma_rx_sconfig.direction = DMA_DEV_TO_MEM; @@ -1043,8 +1082,14 @@ static inline int lpuart_start_rx_dma(struct lpuart_port *sport) sport->dma_rx_cookie = dmaengine_submit(sport->dma_rx_desc); dma_async_issue_pending(sport->dma_rx_chan); - writeb(readb(sport->port.membase + UARTCR5) | UARTCR5_RDMAS, - sport->port.membase + UARTCR5); + if (lpuart_is_32(sport)) { + unsigned long temp = lpuart32_read(&sport->port, UARTBAUD); + + lpuart32_write(&sport->port, temp | UARTBAUD_RDMAE, UARTBAUD); + } else { + writeb(readb(sport->port.membase + UARTCR5) | UARTCR5_RDMAS, + sport->port.membase + UARTCR5); + } return 0; } @@ -1334,6 +1379,8 @@ static int lpuart32_startup(struct uart_port *port) sport->txfifo_size = 0x1 << (((temp >> UARTFIFO_TXSIZE_OFF) & UARTFIFO_FIFOSIZE_MASK) - 1); + sport->port.fifosize = sport->txfifo_size; + sport->rxfifo_size = 0x1 << (((temp >> UARTFIFO_RXSIZE_OFF) & UARTFIFO_FIFOSIZE_MASK) - 1); @@ -1342,8 +1389,41 @@ static int lpuart32_startup(struct uart_port *port) lpuart32_setup_watermark(sport); temp = lpuart32_read(&sport->port, UARTCTRL); - temp |= (UARTCTRL_RIE | UARTCTRL_TIE | UARTCTRL_RE | UARTCTRL_TE); - temp |= UARTCTRL_ILIE; + temp |= UARTCTRL_RE | UARTCTRL_TE | UARTCTRL_ILIE; + lpuart32_write(&sport->port, temp, UARTCTRL); + + if (sport->dma_rx_chan && !lpuart_start_rx_dma(sport)) { + /* set Rx DMA timeout */ + sport->dma_rx_timeout = msecs_to_jiffies(DMA_RX_TIMEOUT); + if (!sport->dma_rx_timeout) + sport->dma_rx_timeout = 1; + + sport->lpuart_dma_rx_use = true; + rx_dma_timer_init(sport); + } else { + sport->lpuart_dma_rx_use = false; + } + + if (sport->dma_tx_chan && !lpuart_dma_tx_request(port)) { + init_waitqueue_head(&sport->dma_wait); + sport->lpuart_dma_tx_use = true; + temp = lpuart32_read(&sport->port, UARTBAUD); + lpuart32_write(&sport->port, temp | UARTBAUD_TDMAE, UARTBAUD); + } else { + sport->lpuart_dma_tx_use = false; + } + + if (sport->lpuart_dma_rx_use) { + /* RXWATER must be 0 */ + temp = lpuart32_read(&sport->port, UARTWATER); + temp &= ~(UARTWATER_WATER_MASK << UARTWATER_RXWATER_OFF); + lpuart32_write(&sport->port, temp, UARTWATER); + } + temp = lpuart32_read(&sport->port, UARTCTRL); + if (!sport->lpuart_dma_rx_use) + temp |= UARTCTRL_RIE; + if (!sport->lpuart_dma_tx_use) + temp |= UARTCTRL_TIE; lpuart32_write(&sport->port, temp, UARTCTRL); spin_unlock_irqrestore(&sport->port.lock, flags); @@ -1384,6 +1464,8 @@ static void lpuart_shutdown(struct uart_port *port) static void lpuart32_shutdown(struct uart_port *port) { + struct lpuart_port *sport = + container_of(port, struct lpuart_port, port); unsigned long temp; unsigned long flags; @@ -1396,6 +1478,21 @@ static void lpuart32_shutdown(struct uart_port *port) lpuart32_write(port, temp, UARTCTRL); spin_unlock_irqrestore(&port->lock, flags); + + if (sport->lpuart_dma_rx_use) { + del_timer_sync(&sport->lpuart_timer); + lpuart_dma_rx_free(&sport->port); + } + + if (sport->lpuart_dma_tx_use) { + if (wait_event_interruptible(sport->dma_wait, + !sport->dma_tx_in_progress)) { + sport->dma_tx_in_progress = false; + dmaengine_terminate_all(sport->dma_tx_chan); + } + + lpuart32_stop_tx(port); + } } static void @@ -1621,7 +1718,10 @@ lpuart32_serial_setbrg(struct lpuart_port *sport, unsigned int baudrate) tmp &= ~UARTBAUD_SBR_MASK; tmp |= sbr & UARTBAUD_SBR_MASK; - tmp &= ~(UARTBAUD_TDMAE | UARTBAUD_RDMAE); + if (!sport->lpuart_dma_rx_use) + tmp &= ~UARTBAUD_RDMAE; + if (!sport->lpuart_dma_tx_use) + tmp &= ~UARTBAUD_TDMAE; lpuart32_write(&sport->port, tmp, UARTBAUD); } @@ -1699,6 +1799,18 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios, /* ask the core to calculate the divisor */ baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 4); + /* + * Need to update the Ring buffer length according to the selected + * baud rate and restart Rx DMA path. + * + * Since timer function acqures sport->port.lock, need to stop before + * acquring same lock because otherwise del_timer_sync() can deadlock. + */ + if (old && sport->lpuart_dma_rx_use) { + del_timer_sync(&sport->lpuart_timer); + lpuart_dma_rx_free(&sport->port); + } + spin_lock_irqsave(&sport->port.lock, flags); sport->port.read_status_mask = 0; @@ -1737,6 +1849,13 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios, lpuart32_write(&sport->port, ctrl, UARTCTRL); /* restore control register */ + if (old && sport->lpuart_dma_rx_use) { + if (!lpuart_start_rx_dma(sport)) + rx_dma_timer_init(sport); + else + sport->lpuart_dma_rx_use = false; + } + spin_unlock_irqrestore(&sport->port.lock, flags); } @@ -2306,8 +2425,14 @@ static int lpuart_suspend(struct device *dev) } /* Disable Rx DMA to use UART port as wakeup source */ - writeb(readb(sport->port.membase + UARTCR5) & ~UARTCR5_RDMAS, - sport->port.membase + UARTCR5); + if (lpuart_is_32(sport)) { + temp = lpuart32_read(&sport->port, UARTBAUD); + lpuart32_write(&sport->port, temp & ~UARTBAUD_RDMAE, + UARTBAUD); + } else { + writeb(readb(sport->port.membase + UARTCR5) & + ~UARTCR5_RDMAS, sport->port.membase + UARTCR5); + } } if (sport->lpuart_dma_tx_use) { @@ -2333,8 +2458,7 @@ static int lpuart_resume(struct device *dev) if (lpuart_is_32(sport)) { lpuart32_setup_watermark(sport); temp = lpuart32_read(&sport->port, UARTCTRL); - temp |= (UARTCTRL_RIE | UARTCTRL_TIE | UARTCTRL_RE | - UARTCTRL_TE | UARTCTRL_ILIE); + temp |= UARTCTRL_RE | UARTCTRL_TE | UARTCTRL_ILIE; lpuart32_write(&sport->port, temp, UARTCTRL); } else { lpuart_setup_watermark(sport); @@ -2353,14 +2477,36 @@ static int lpuart_resume(struct device *dev) } if (sport->dma_tx_chan && !lpuart_dma_tx_request(&sport->port)) { - init_waitqueue_head(&sport->dma_wait); - sport->lpuart_dma_tx_use = true; + init_waitqueue_head(&sport->dma_wait); + sport->lpuart_dma_tx_use = true; + if (lpuart_is_32(sport)) { + temp = lpuart32_read(&sport->port, UARTBAUD); + lpuart32_write(&sport->port, + temp | UARTBAUD_TDMAE, UARTBAUD); + } else { writeb(readb(sport->port.membase + UARTCR5) | UARTCR5_TDMAS, sport->port.membase + UARTCR5); + } } else { sport->lpuart_dma_tx_use = false; } + if (lpuart_is_32(sport)) { + if (sport->lpuart_dma_rx_use) { + /* RXWATER must be 0 */ + temp = lpuart32_read(&sport->port, UARTWATER); + temp &= ~(UARTWATER_WATER_MASK << + UARTWATER_RXWATER_OFF); + lpuart32_write(&sport->port, temp, UARTWATER); + } + temp = lpuart32_read(&sport->port, UARTCTRL); + if (!sport->lpuart_dma_rx_use) + temp |= UARTCTRL_RIE; + if (!sport->lpuart_dma_tx_use) + temp |= UARTCTRL_TIE; + lpuart32_write(&sport->port, temp, UARTCTRL); + } + uart_resume_port(&lpuart_reg, &sport->port); return 0; diff --git a/drivers/tty/serial/lpc32xx_hs.c b/drivers/tty/serial/lpc32xx_hs.c index d1d73261575b..f4e27d0ad947 100644 --- a/drivers/tty/serial/lpc32xx_hs.c +++ b/drivers/tty/serial/lpc32xx_hs.c @@ -151,6 +151,8 @@ static void lpc32xx_hsuart_console_write(struct console *co, const char *s, local_irq_restore(flags); } +static void lpc32xx_loopback_set(resource_size_t mapbase, int state); + static int __init lpc32xx_hsuart_console_setup(struct console *co, char *options) { @@ -170,6 +172,8 @@ static int __init lpc32xx_hsuart_console_setup(struct console *co, if (options) uart_parse_options(options, &baud, &parity, &bits, &flow); + lpc32xx_loopback_set(port->mapbase, 0); /* get out of loopback mode */ + return uart_set_options(port, co, baud, parity, bits, flow); } diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c index 4f479841769a..f5bdde405627 100644 --- a/drivers/tty/serial/max310x.c +++ b/drivers/tty/serial/max310x.c @@ -248,6 +248,7 @@ struct max310x_devtype { char name[9]; int nr; + u8 mode1; int (*detect)(struct device *); void (*power)(struct uart_port *, int); }; @@ -410,6 +411,7 @@ static void max14830_power(struct uart_port *port, int on) static const struct max310x_devtype max3107_devtype = { .name = "MAX3107", .nr = 1, + .mode1 = MAX310X_MODE1_AUTOSLEEP_BIT | MAX310X_MODE1_IRQSEL_BIT, .detect = max3107_detect, .power = max310x_power, }; @@ -417,6 +419,7 @@ static const struct max310x_devtype max3107_devtype = { static const struct max310x_devtype max3108_devtype = { .name = "MAX3108", .nr = 1, + .mode1 = MAX310X_MODE1_AUTOSLEEP_BIT, .detect = max3108_detect, .power = max310x_power, }; @@ -424,6 +427,7 @@ static const struct max310x_devtype max3108_devtype = { static const struct max310x_devtype max3109_devtype = { .name = "MAX3109", .nr = 2, + .mode1 = MAX310X_MODE1_AUTOSLEEP_BIT, .detect = max3109_detect, .power = max310x_power, }; @@ -431,6 +435,7 @@ static const struct max310x_devtype max3109_devtype = { static const struct max310x_devtype max14830_devtype = { .name = "MAX14830", .nr = 4, + .mode1 = MAX310X_MODE1_IRQSEL_BIT, .detect = max14830_detect, .power = max14830_power, }; @@ -1197,8 +1202,7 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype, return PTR_ERR(regmap); /* Alloc port structure */ - s = devm_kzalloc(dev, sizeof(*s) + - sizeof(struct max310x_one) * devtype->nr, GFP_KERNEL); + s = devm_kzalloc(dev, struct_size(s, p, devtype->nr), GFP_KERNEL); if (!s) { dev_err(dev, "Error allocating port structure\n"); return -ENOMEM; @@ -1258,9 +1262,8 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype, MAX310X_BRGDIVLSB_REG + offs, &ret); } while (ret != 0x01); - regmap_update_bits(s->regmap, MAX310X_MODE1_REG + offs, - MAX310X_MODE1_AUTOSLEEP_BIT, - MAX310X_MODE1_AUTOSLEEP_BIT); + regmap_write(s->regmap, MAX310X_MODE1_REG + offs, + devtype->mode1); } uartclk = max310x_set_ref_clk(dev, s, freq, xtal); @@ -1294,10 +1297,6 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype, max310x_port_write(&s->p[i].port, MAX310X_IRQEN_REG, 0); /* Clear IRQ status register */ max310x_port_read(&s->p[i].port, MAX310X_IRQSTS_REG); - /* Enable IRQ pin */ - max310x_port_update(&s->p[i].port, MAX310X_MODE1_REG, - MAX310X_MODE1_IRQSEL_BIT, - MAX310X_MODE1_IRQSEL_BIT); /* Initialize queue for start TX */ INIT_WORK(&s->p[i].tx_work, max310x_wq_proc); /* Initialize queue for changing LOOPBACK mode */ @@ -1467,10 +1466,10 @@ static int __init max310x_uart_init(void) return ret; #ifdef CONFIG_SPI_MASTER - spi_register_driver(&max310x_spi_driver); + ret = spi_register_driver(&max310x_spi_driver); #endif - return 0; + return ret; } module_init(max310x_uart_init); diff --git a/drivers/tty/serial/meson_uart.c b/drivers/tty/serial/meson_uart.c index 8a842591b37c..fbc5bc022a39 100644 --- a/drivers/tty/serial/meson_uart.c +++ b/drivers/tty/serial/meson_uart.c @@ -72,7 +72,8 @@ #define AML_UART_BAUD_USE BIT(23) #define AML_UART_BAUD_XTAL BIT(24) -#define AML_UART_PORT_NUM 6 +#define AML_UART_PORT_NUM 12 +#define AML_UART_PORT_OFFSET 6 #define AML_UART_DEV_NAME "ttyAML" @@ -654,10 +655,20 @@ static int meson_uart_probe(struct platform_device *pdev) struct resource *res_mem, *res_irq; struct uart_port *port; int ret = 0; + int id = -1; if (pdev->dev.of_node) pdev->id = of_alias_get_id(pdev->dev.of_node, "serial"); + if (pdev->id < 0) { + for (id = AML_UART_PORT_OFFSET; id < AML_UART_PORT_NUM; id++) { + if (!meson_ports[id]) { + pdev->id = id; + break; + } + } + } + if (pdev->id < 0 || pdev->id >= AML_UART_PORT_NUM) return -EINVAL; diff --git a/drivers/tty/serial/mps2-uart.c b/drivers/tty/serial/mps2-uart.c index 9f8f63719126..587b42f754cb 100644 --- a/drivers/tty/serial/mps2-uart.c +++ b/drivers/tty/serial/mps2-uart.c @@ -22,6 +22,7 @@ #include <linux/serial_core.h> #include <linux/tty_flip.h> #include <linux/types.h> +#include <linux/idr.h> #define SERIAL_NAME "ttyMPS" #define DRIVER_NAME "mps2-uart" @@ -65,11 +66,14 @@ #define MPS2_MAX_PORTS 3 +#define UART_PORT_COMBINED_IRQ BIT(0) + struct mps2_uart_port { struct uart_port port; struct clk *clk; unsigned int tx_irq; unsigned int rx_irq; + unsigned int flags; }; static inline struct mps2_uart_port *to_mps2_port(struct uart_port *port) @@ -264,6 +268,20 @@ static irqreturn_t mps2_uart_oerrirq(int irq, void *data) return handled; } +static irqreturn_t mps2_uart_combinedirq(int irq, void *data) +{ + if (mps2_uart_rxirq(irq, data) == IRQ_HANDLED) + return IRQ_HANDLED; + + if (mps2_uart_txirq(irq, data) == IRQ_HANDLED) + return IRQ_HANDLED; + + if (mps2_uart_oerrirq(irq, data) == IRQ_HANDLED) + return IRQ_HANDLED; + + return IRQ_NONE; +} + static int mps2_uart_startup(struct uart_port *port) { struct mps2_uart_port *mps_port = to_mps2_port(port); @@ -274,26 +292,37 @@ static int mps2_uart_startup(struct uart_port *port) mps2_uart_write8(port, control, UARTn_CTRL); - ret = request_irq(mps_port->rx_irq, mps2_uart_rxirq, 0, - MAKE_NAME(-rx), mps_port); - if (ret) { - dev_err(port->dev, "failed to register rxirq (%d)\n", ret); - return ret; - } + if (mps_port->flags & UART_PORT_COMBINED_IRQ) { + ret = request_irq(port->irq, mps2_uart_combinedirq, 0, + MAKE_NAME(-combined), mps_port); - ret = request_irq(mps_port->tx_irq, mps2_uart_txirq, 0, - MAKE_NAME(-tx), mps_port); - if (ret) { - dev_err(port->dev, "failed to register txirq (%d)\n", ret); - goto err_free_rxirq; - } + if (ret) { + dev_err(port->dev, "failed to register combinedirq (%d)\n", ret); + return ret; + } + } else { + ret = request_irq(port->irq, mps2_uart_oerrirq, IRQF_SHARED, + MAKE_NAME(-overrun), mps_port); + + if (ret) { + dev_err(port->dev, "failed to register oerrirq (%d)\n", ret); + return ret; + } + + ret = request_irq(mps_port->rx_irq, mps2_uart_rxirq, 0, + MAKE_NAME(-rx), mps_port); + if (ret) { + dev_err(port->dev, "failed to register rxirq (%d)\n", ret); + goto err_free_oerrirq; + } - ret = request_irq(port->irq, mps2_uart_oerrirq, IRQF_SHARED, - MAKE_NAME(-overrun), mps_port); + ret = request_irq(mps_port->tx_irq, mps2_uart_txirq, 0, + MAKE_NAME(-tx), mps_port); + if (ret) { + dev_err(port->dev, "failed to register txirq (%d)\n", ret); + goto err_free_rxirq; + } - if (ret) { - dev_err(port->dev, "failed to register oerrirq (%d)\n", ret); - goto err_free_txirq; } control |= UARTn_CTRL_RX_GRP | UARTn_CTRL_TX_GRP; @@ -302,10 +331,10 @@ static int mps2_uart_startup(struct uart_port *port) return 0; -err_free_txirq: - free_irq(mps_port->tx_irq, mps_port); err_free_rxirq: free_irq(mps_port->rx_irq, mps_port); +err_free_oerrirq: + free_irq(port->irq, mps_port); return ret; } @@ -319,8 +348,11 @@ static void mps2_uart_shutdown(struct uart_port *port) mps2_uart_write8(port, control, UARTn_CTRL); - free_irq(mps_port->rx_irq, mps_port); - free_irq(mps_port->tx_irq, mps_port); + if (!(mps_port->flags & UART_PORT_COMBINED_IRQ)) { + free_irq(mps_port->rx_irq, mps_port); + free_irq(mps_port->tx_irq, mps_port); + } + free_irq(port->irq, mps_port); } @@ -397,7 +429,7 @@ static const struct uart_ops mps2_uart_pops = { .verify_port = mps2_uart_verify_port, }; -static struct mps2_uart_port mps2_uart_ports[MPS2_MAX_PORTS]; +static DEFINE_IDR(ports_idr); #ifdef CONFIG_SERIAL_MPS2_UART_CONSOLE static void mps2_uart_console_putchar(struct uart_port *port, int ch) @@ -410,7 +442,8 @@ static void mps2_uart_console_putchar(struct uart_port *port, int ch) static void mps2_uart_console_write(struct console *co, const char *s, unsigned int cnt) { - struct uart_port *port = &mps2_uart_ports[co->index].port; + struct mps2_uart_port *mps_port = idr_find(&ports_idr, co->index); + struct uart_port *port = &mps_port->port; uart_console_write(port, s, cnt, mps2_uart_console_putchar); } @@ -426,7 +459,10 @@ static int mps2_uart_console_setup(struct console *co, char *options) if (co->index < 0 || co->index >= MPS2_MAX_PORTS) return -ENODEV; - mps_port = &mps2_uart_ports[co->index]; + mps_port = idr_find(&ports_idr, co->index); + + if (!mps_port) + return -ENODEV; if (options) uart_parse_options(options, &baud, &parity, &bits, &flow); @@ -487,27 +523,36 @@ static struct uart_driver mps2_uart_driver = { .cons = MPS2_SERIAL_CONSOLE, }; -static struct mps2_uart_port *mps2_of_get_port(struct platform_device *pdev) +static int mps2_of_get_port(struct platform_device *pdev, + struct mps2_uart_port *mps_port) { struct device_node *np = pdev->dev.of_node; int id; if (!np) - return NULL; + return -ENODEV; id = of_alias_get_id(np, "serial"); + if (id < 0) - id = 0; + id = idr_alloc_cyclic(&ports_idr, (void *)mps_port, 0, MPS2_MAX_PORTS, GFP_KERNEL); + else + id = idr_alloc(&ports_idr, (void *)mps_port, id, MPS2_MAX_PORTS, GFP_KERNEL); - if (WARN_ON(id >= MPS2_MAX_PORTS)) - return NULL; + if (id < 0) + return id; + + /* Only combined irq is presesnt */ + if (platform_irq_count(pdev) == 1) + mps_port->flags |= UART_PORT_COMBINED_IRQ; + + mps_port->port.line = id; - mps2_uart_ports[id].port.line = id; - return &mps2_uart_ports[id]; + return 0; } -static int mps2_init_port(struct mps2_uart_port *mps_port, - struct platform_device *pdev) +static int mps2_init_port(struct platform_device *pdev, + struct mps2_uart_port *mps_port) { struct resource *res; int ret; @@ -519,11 +564,6 @@ static int mps2_init_port(struct mps2_uart_port *mps_port, mps_port->port.mapbase = res->start; mps_port->port.mapsize = resource_size(res); - - mps_port->rx_irq = platform_get_irq(pdev, 0); - mps_port->tx_irq = platform_get_irq(pdev, 1); - mps_port->port.irq = platform_get_irq(pdev, 2); - mps_port->port.iotype = UPIO_MEM; mps_port->port.flags = UPF_BOOT_AUTOCONF; mps_port->port.fifosize = 1; @@ -542,6 +582,15 @@ static int mps2_init_port(struct mps2_uart_port *mps_port, clk_disable_unprepare(mps_port->clk); + + if (mps_port->flags & UART_PORT_COMBINED_IRQ) { + mps_port->port.irq = platform_get_irq(pdev, 0); + } else { + mps_port->rx_irq = platform_get_irq(pdev, 0); + mps_port->tx_irq = platform_get_irq(pdev, 1); + mps_port->port.irq = platform_get_irq(pdev, 2); + } + return ret; } @@ -550,11 +599,16 @@ static int mps2_serial_probe(struct platform_device *pdev) struct mps2_uart_port *mps_port; int ret; - mps_port = mps2_of_get_port(pdev); - if (!mps_port) - return -ENODEV; + mps_port = devm_kzalloc(&pdev->dev, sizeof(struct mps2_uart_port), GFP_KERNEL); + + if (!mps_port) + return -ENOMEM; + + ret = mps2_of_get_port(pdev, mps_port); + if (ret) + return ret; - ret = mps2_init_port(mps_port, pdev); + ret = mps2_init_port(pdev, mps_port); if (ret) return ret; diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c index 736b74fd6623..109096033bb1 100644 --- a/drivers/tty/serial/msm_serial.c +++ b/drivers/tty/serial/msm_serial.c @@ -1634,7 +1634,7 @@ static void msm_console_write(struct console *co, const char *s, __msm_console_write(port, s, count, msm_port->is_uartdm); } -static int __init msm_console_setup(struct console *co, char *options) +static int msm_console_setup(struct console *co, char *options) { struct uart_port *port; int baud = 115200; diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c index 38016609c7fa..3bcec1c20219 100644 --- a/drivers/tty/serial/qcom_geni_serial.c +++ b/drivers/tty/serial/qcom_geni_serial.c @@ -89,7 +89,7 @@ #define DEF_FIFO_DEPTH_WORDS 16 #define DEF_TX_WM 2 #define DEF_FIFO_WIDTH_BITS 32 -#define UART_CONSOLE_RX_WM 2 +#define UART_RX_WM 2 #define MAX_LOOPBACK_CFG 3 #ifdef CONFIG_CONSOLE_POLL @@ -105,10 +105,6 @@ struct qcom_geni_serial_port { u32 tx_fifo_depth; u32 tx_fifo_width; u32 rx_fifo_depth; - u32 tx_wm; - u32 rx_wm; - u32 rx_rfr; - enum geni_se_xfer_mode xfer_mode; bool setup; int (*handle_rx)(struct uart_port *uport, u32 bytes, bool drop); unsigned int baud; @@ -228,7 +224,7 @@ static unsigned int qcom_geni_serial_get_mctrl(struct uart_port *uport) if (uart_console(uport)) { mctrl |= TIOCM_CTS; } else { - geni_ios = readl_relaxed(uport->membase + SE_GENI_IOS); + geni_ios = readl(uport->membase + SE_GENI_IOS); if (!(geni_ios & IO2_DATA_IN)) mctrl |= TIOCM_CTS; } @@ -246,7 +242,7 @@ static void qcom_geni_serial_set_mctrl(struct uart_port *uport, if (!(mctrl & TIOCM_RTS)) uart_manual_rfr = UART_MANUAL_RFR_EN | UART_RFR_NOT_READY; - writel_relaxed(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR); + writel(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR); } static const char *qcom_geni_serial_get_type(struct uart_port *uport) @@ -275,9 +271,6 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport, unsigned int fifo_bits; unsigned long timeout_us = 20000; - /* Ensure polling is not re-ordered before the prior writes/reads */ - mb(); - if (uport->private_data) { port = to_dev_port(uport, uport); baud = port->baud; @@ -297,7 +290,7 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport, */ timeout_us = DIV_ROUND_UP(timeout_us, 10) * 10; while (timeout_us) { - reg = readl_relaxed(uport->membase + offset); + reg = readl(uport->membase + offset); if ((bool)(reg & field) == set) return true; udelay(10); @@ -310,7 +303,7 @@ static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size) { u32 m_cmd; - writel_relaxed(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN); + writel(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN); m_cmd = UART_START_TX << M_OPCODE_SHFT; writel(m_cmd, uport->membase + SE_GENI_M_CMD0); } @@ -323,13 +316,13 @@ static void qcom_geni_serial_poll_tx_done(struct uart_port *uport) done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_DONE_EN, true); if (!done) { - writel_relaxed(M_GENI_CMD_ABORT, uport->membase + + writel(M_GENI_CMD_ABORT, uport->membase + SE_GENI_M_CMD_CTRL_REG); irq_clear |= M_CMD_ABORT_EN; qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_ABORT_EN, true); } - writel_relaxed(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR); + writel(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR); } static void qcom_geni_serial_abort_rx(struct uart_port *uport) @@ -339,8 +332,8 @@ static void qcom_geni_serial_abort_rx(struct uart_port *uport) writel(S_GENI_CMD_ABORT, uport->membase + SE_GENI_S_CMD_CTRL_REG); qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG, S_GENI_CMD_ABORT, false); - writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); - writel_relaxed(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG); + writel(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); + writel(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG); } #ifdef CONFIG_CONSOLE_POLL @@ -349,19 +342,13 @@ static int qcom_geni_serial_get_char(struct uart_port *uport) u32 rx_fifo; u32 status; - status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS); - writel_relaxed(status, uport->membase + SE_GENI_M_IRQ_CLEAR); + status = readl(uport->membase + SE_GENI_M_IRQ_STATUS); + writel(status, uport->membase + SE_GENI_M_IRQ_CLEAR); - status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS); - writel_relaxed(status, uport->membase + SE_GENI_S_IRQ_CLEAR); + status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); + writel(status, uport->membase + SE_GENI_S_IRQ_CLEAR); - /* - * Ensure the writes to clear interrupts is not re-ordered after - * reading the data. - */ - mb(); - - status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS); + status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS); if (!(status & RX_FIFO_WC_MSK)) return NO_POLL_CHAR; @@ -372,15 +359,12 @@ static int qcom_geni_serial_get_char(struct uart_port *uport) static void qcom_geni_serial_poll_put_char(struct uart_port *uport, unsigned char c) { - struct qcom_geni_serial_port *port = to_dev_port(uport, uport); - - writel_relaxed(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG); + writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); qcom_geni_serial_setup_tx(uport, 1); WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_TX_FIFO_WATERMARK_EN, true)); - writel_relaxed(c, uport->membase + SE_GENI_TX_FIFOn); - writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase + - SE_GENI_M_IRQ_CLEAR); + writel(c, uport->membase + SE_GENI_TX_FIFOn); + writel(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); qcom_geni_serial_poll_tx_done(uport); } #endif @@ -388,7 +372,7 @@ static void qcom_geni_serial_poll_put_char(struct uart_port *uport, #ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE static void qcom_geni_serial_wr_char(struct uart_port *uport, int ch) { - writel_relaxed(ch, uport->membase + SE_GENI_TX_FIFOn); + writel(ch, uport->membase + SE_GENI_TX_FIFOn); } static void @@ -407,7 +391,7 @@ __qcom_geni_serial_console_write(struct uart_port *uport, const char *s, bytes_to_send++; } - writel_relaxed(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); + writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); qcom_geni_serial_setup_tx(uport, bytes_to_send); for (i = 0; i < count; ) { size_t chars_to_write = 0; @@ -425,7 +409,7 @@ __qcom_geni_serial_console_write(struct uart_port *uport, const char *s, chars_to_write = min_t(size_t, count - i, avail / 2); uart_console_write(uport, s + i, chars_to_write, qcom_geni_serial_wr_char); - writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase + + writel(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); i += chars_to_write; } @@ -454,7 +438,7 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s, else spin_lock_irqsave(&uport->lock, flags); - geni_status = readl_relaxed(uport->membase + SE_GENI_STATUS); + geni_status = readl(uport->membase + SE_GENI_STATUS); /* Cancel the current write to log the fault */ if (!locked) { @@ -464,11 +448,10 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s, geni_se_abort_m_cmd(&port->se); qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_ABORT_EN, true); - writel_relaxed(M_CMD_ABORT_EN, uport->membase + + writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } - writel_relaxed(M_CMD_CANCEL_EN, uport->membase + - SE_GENI_M_IRQ_CLEAR); + writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } else if ((geni_status & M_GENI_CMD_ACTIVE) && !port->tx_remaining) { /* * It seems we can't interrupt existing transfers if all data @@ -477,9 +460,8 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s, qcom_geni_serial_poll_tx_done(uport); if (uart_circ_chars_pending(&uport->state->xmit)) { - irq_en = readl_relaxed(uport->membase + - SE_GENI_M_IRQ_EN); - writel_relaxed(irq_en | M_TX_FIFO_WATERMARK_EN, + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); + writel(irq_en | M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_EN); } } @@ -567,29 +549,20 @@ static int handle_rx_uart(struct uart_port *uport, u32 bytes, bool drop) static void qcom_geni_serial_start_tx(struct uart_port *uport) { u32 irq_en; - struct qcom_geni_serial_port *port = to_dev_port(uport, uport); u32 status; - if (port->xfer_mode == GENI_SE_FIFO) { - /* - * readl ensures reading & writing of IRQ_EN register - * is not re-ordered before checking the status of the - * Serial Engine. - */ - status = readl(uport->membase + SE_GENI_STATUS); - if (status & M_GENI_CMD_ACTIVE) - return; + status = readl(uport->membase + SE_GENI_STATUS); + if (status & M_GENI_CMD_ACTIVE) + return; - if (!qcom_geni_serial_tx_empty(uport)) - return; + if (!qcom_geni_serial_tx_empty(uport)) + return; - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); - irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN; + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); + irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN; - writel_relaxed(port->tx_wm, uport->membase + - SE_GENI_TX_WATERMARK_REG); - writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); - } + writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); + writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); } static void qcom_geni_serial_stop_tx(struct uart_port *uport) @@ -598,35 +571,24 @@ static void qcom_geni_serial_stop_tx(struct uart_port *uport) u32 status; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); - irq_en &= ~M_CMD_DONE_EN; - if (port->xfer_mode == GENI_SE_FIFO) { - irq_en &= ~M_TX_FIFO_WATERMARK_EN; - writel_relaxed(0, uport->membase + - SE_GENI_TX_WATERMARK_REG); - } - writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); - status = readl_relaxed(uport->membase + SE_GENI_STATUS); + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); + irq_en &= ~(M_CMD_DONE_EN | M_TX_FIFO_WATERMARK_EN); + writel(0, uport->membase + SE_GENI_TX_WATERMARK_REG); + writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); + status = readl(uport->membase + SE_GENI_STATUS); /* Possible stop tx is called multiple times. */ if (!(status & M_GENI_CMD_ACTIVE)) return; - /* - * Ensure cancel command write is not re-ordered before checking - * the status of the Primary Sequencer. - */ - mb(); - geni_se_cancel_m_cmd(&port->se); if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_CANCEL_EN, true)) { geni_se_abort_m_cmd(&port->se); qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_ABORT_EN, true); - writel_relaxed(M_CMD_ABORT_EN, uport->membase + - SE_GENI_M_IRQ_CLEAR); + writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } - writel_relaxed(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); + writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } static void qcom_geni_serial_start_rx(struct uart_port *uport) @@ -635,27 +597,19 @@ static void qcom_geni_serial_start_rx(struct uart_port *uport) u32 status; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); - status = readl_relaxed(uport->membase + SE_GENI_STATUS); + status = readl(uport->membase + SE_GENI_STATUS); if (status & S_GENI_CMD_ACTIVE) qcom_geni_serial_stop_rx(uport); - /* - * Ensure setup command write is not re-ordered before checking - * the status of the Secondary Sequencer. - */ - mb(); - geni_se_setup_s_cmd(&port->se, UART_START_READ, 0); - if (port->xfer_mode == GENI_SE_FIFO) { - irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN); - irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN; - writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN); + irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN; + writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN); - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); - irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN; - writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); - } + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); + irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN; + writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); } static void qcom_geni_serial_stop_rx(struct uart_port *uport) @@ -665,32 +619,24 @@ static void qcom_geni_serial_stop_rx(struct uart_port *uport) struct qcom_geni_serial_port *port = to_dev_port(uport, uport); u32 irq_clear = S_CMD_DONE_EN; - if (port->xfer_mode == GENI_SE_FIFO) { - irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN); - irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN); - writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN); + irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN); + writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN); - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); - irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN); - writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); - } + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); + irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN); + writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); - status = readl_relaxed(uport->membase + SE_GENI_STATUS); + status = readl(uport->membase + SE_GENI_STATUS); /* Possible stop rx is called multiple times. */ if (!(status & S_GENI_CMD_ACTIVE)) return; - /* - * Ensure cancel command write is not re-ordered before checking - * the status of the Secondary Sequencer. - */ - mb(); - geni_se_cancel_s_cmd(&port->se); qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG, S_GENI_CMD_CANCEL, false); - status = readl_relaxed(uport->membase + SE_GENI_STATUS); - writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); + status = readl(uport->membase + SE_GENI_STATUS); + writel(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); if (status & S_GENI_CMD_ACTIVE) qcom_geni_serial_abort_rx(uport); } @@ -704,7 +650,7 @@ static void qcom_geni_serial_handle_rx(struct uart_port *uport, bool drop) u32 total_bytes; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); - status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS); + status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS); word_cnt = status & RX_FIFO_WC_MSK; last_word_partial = status & RX_LAST; last_word_byte_cnt = (status & RX_LAST_BYTE_VALID_MSK) >> @@ -734,7 +680,7 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done, unsigned int chunk; int tail; - status = readl_relaxed(uport->membase + SE_GENI_TX_FIFO_STATUS); + status = readl(uport->membase + SE_GENI_TX_FIFO_STATUS); /* Complete the current tx command before taking newly added data */ if (active) @@ -760,9 +706,9 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done, qcom_geni_serial_setup_tx(uport, pending); port->tx_remaining = pending; - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); if (!(irq_en & M_TX_FIFO_WATERMARK_EN)) - writel_relaxed(irq_en | M_TX_FIFO_WATERMARK_EN, + writel(irq_en | M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_EN); } @@ -795,14 +741,14 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done, * cleared it in qcom_geni_serial_isr it will have already reasserted * so we must clear it again here after our writes. */ - writel_relaxed(M_TX_FIFO_WATERMARK_EN, + writel(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); out_write_wakeup: if (!port->tx_remaining) { - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); if (irq_en & M_TX_FIFO_WATERMARK_EN) - writel_relaxed(irq_en & ~M_TX_FIFO_WATERMARK_EN, + writel(irq_en & ~M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_EN); } @@ -812,12 +758,12 @@ out_write_wakeup: static irqreturn_t qcom_geni_serial_isr(int isr, void *dev) { - unsigned int m_irq_status; - unsigned int s_irq_status; - unsigned int geni_status; + u32 m_irq_en; + u32 m_irq_status; + u32 s_irq_status; + u32 geni_status; struct uart_port *uport = dev; unsigned long flags; - unsigned int m_irq_en; bool drop_rx = false; struct tty_port *tport = &uport->state->port; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); @@ -826,12 +772,12 @@ static irqreturn_t qcom_geni_serial_isr(int isr, void *dev) return IRQ_NONE; spin_lock_irqsave(&uport->lock, flags); - m_irq_status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS); - s_irq_status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS); - geni_status = readl_relaxed(uport->membase + SE_GENI_STATUS); - m_irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); - writel_relaxed(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR); - writel_relaxed(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR); + m_irq_status = readl(uport->membase + SE_GENI_M_IRQ_STATUS); + s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); + geni_status = readl(uport->membase + SE_GENI_STATUS); + m_irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); + writel(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR); + writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR); if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN)) goto out_unlock; @@ -877,17 +823,6 @@ static void get_tx_fifo_size(struct qcom_geni_serial_port *port) (port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE; } -static void set_rfr_wm(struct qcom_geni_serial_port *port) -{ - /* - * Set RFR (Flow off) to FIFO_DEPTH - 2. - * RX WM level at 10% RX_FIFO_DEPTH. - * TX WM level at 10% TX_FIFO_DEPTH. - */ - port->rx_rfr = port->rx_fifo_depth - 2; - port->rx_wm = UART_CONSOLE_RX_WM; - port->tx_wm = DEF_TX_WM; -} static void qcom_geni_serial_shutdown(struct uart_port *uport) { @@ -907,7 +842,7 @@ static void qcom_geni_serial_shutdown(struct uart_port *uport) static int qcom_geni_serial_port_setup(struct uart_port *uport) { struct qcom_geni_serial_port *port = to_dev_port(uport, uport); - unsigned int rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT; + u32 rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT; u32 proto; if (uart_console(uport)) { @@ -928,21 +863,19 @@ static int qcom_geni_serial_port_setup(struct uart_port *uport) get_tx_fifo_size(port); - set_rfr_wm(port); - writel_relaxed(rxstale, uport->membase + SE_UART_RX_STALE_CNT); + writel(rxstale, uport->membase + SE_UART_RX_STALE_CNT); /* * Make an unconditional cancel on the main sequencer to reset * it else we could end up in data loss scenarios. */ - port->xfer_mode = GENI_SE_FIFO; if (uart_console(uport)) qcom_geni_serial_poll_tx_done(uport); geni_se_config_packing(&port->se, BITS_PER_BYTE, port->tx_bytes_pw, false, true, false); geni_se_config_packing(&port->se, BITS_PER_BYTE, port->rx_bytes_pw, false, false, true); - geni_se_init(&port->se, port->rx_wm, port->rx_rfr); - geni_se_select_mode(&port->se, port->xfer_mode); + geni_se_init(&port->se, UART_RX_WM, port->rx_fifo_depth - 2); + geni_se_select_mode(&port->se, GENI_SE_FIFO); if (!uart_console(uport)) { port->rx_fifo = devm_kcalloc(uport->dev, port->rx_fifo_depth, sizeof(u32), GFP_KERNEL); @@ -1008,14 +941,14 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport, struct ktermios *termios, struct ktermios *old) { unsigned int baud; - unsigned int bits_per_char; - unsigned int tx_trans_cfg; - unsigned int tx_parity_cfg; - unsigned int rx_trans_cfg; - unsigned int rx_parity_cfg; - unsigned int stop_bit_len; + u32 bits_per_char; + u32 tx_trans_cfg; + u32 tx_parity_cfg; + u32 rx_trans_cfg; + u32 rx_parity_cfg; + u32 stop_bit_len; unsigned int clk_div; - unsigned long ser_clk_cfg; + u32 ser_clk_cfg; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); unsigned long clk_rate; @@ -1033,10 +966,10 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport, ser_clk_cfg |= clk_div << CLK_DIV_SHFT; /* parity */ - tx_trans_cfg = readl_relaxed(uport->membase + SE_UART_TX_TRANS_CFG); - tx_parity_cfg = readl_relaxed(uport->membase + SE_UART_TX_PARITY_CFG); - rx_trans_cfg = readl_relaxed(uport->membase + SE_UART_RX_TRANS_CFG); - rx_parity_cfg = readl_relaxed(uport->membase + SE_UART_RX_PARITY_CFG); + tx_trans_cfg = readl(uport->membase + SE_UART_TX_TRANS_CFG); + tx_parity_cfg = readl(uport->membase + SE_UART_TX_PARITY_CFG); + rx_trans_cfg = readl(uport->membase + SE_UART_RX_TRANS_CFG); + rx_parity_cfg = readl(uport->membase + SE_UART_RX_PARITY_CFG); if (termios->c_cflag & PARENB) { tx_trans_cfg |= UART_TX_PAR_EN; rx_trans_cfg |= UART_RX_PAR_EN; @@ -1092,17 +1025,17 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport, uart_update_timeout(uport, termios->c_cflag, baud); if (!uart_console(uport)) - writel_relaxed(port->loopback, + writel(port->loopback, uport->membase + SE_UART_LOOPBACK_CFG); - writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); - writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); - writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); - writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); - writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); - writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); - writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); - writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG); - writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG); + writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); + writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); + writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); + writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); + writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); + writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); + writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); + writel(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG); + writel(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG); out_restart_rx: qcom_geni_serial_start_rx(uport); } @@ -1193,13 +1126,13 @@ static int __init qcom_geni_serial_earlycon_setup(struct earlycon_device *dev, geni_se_init(&se, DEF_FIFO_DEPTH_WORDS / 2, DEF_FIFO_DEPTH_WORDS - 2); geni_se_select_mode(&se, GENI_SE_FIFO); - writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); - writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); - writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); - writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); - writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); - writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); - writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); + writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); + writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); + writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); + writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); + writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); + writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); + writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); dev->con->write = qcom_geni_serial_earlycon_write; dev->con->setup = NULL; diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c index 9fc3559f80d9..83fd51607741 100644 --- a/drivers/tty/serial/samsung.c +++ b/drivers/tty/serial/samsung.c @@ -1694,6 +1694,42 @@ s3c24xx_serial_cpufreq_deregister(struct s3c24xx_uart_port *port) } #endif +static int s3c24xx_serial_enable_baudclk(struct s3c24xx_uart_port *ourport) +{ + struct device *dev = ourport->port.dev; + struct s3c24xx_uart_info *info = ourport->info; + char clk_name[MAX_CLK_NAME_LENGTH]; + unsigned int clk_sel; + struct clk *clk; + int clk_num; + int ret; + + clk_sel = ourport->cfg->clk_sel ? : info->def_clk_sel; + for (clk_num = 0; clk_num < info->num_clks; clk_num++) { + if (!(clk_sel & (1 << clk_num))) + continue; + + sprintf(clk_name, "clk_uart_baud%d", clk_num); + clk = clk_get(dev, clk_name); + if (IS_ERR(clk)) + continue; + + ret = clk_prepare_enable(clk); + if (ret) { + clk_put(clk); + continue; + } + + ourport->baudclk = clk; + ourport->baudclk_rate = clk_get_rate(clk); + s3c24xx_serial_setsource(&ourport->port, clk_num); + + return 0; + } + + return -EINVAL; +} + /* s3c24xx_serial_init_port * * initialise a single serial port from the platform device given @@ -1788,6 +1824,10 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport, goto err; } + ret = s3c24xx_serial_enable_baudclk(ourport); + if (ret) + pr_warn("uart: failed to enable baudclk\n"); + /* Keep all interrupts masked and cleared */ if (s3c24xx_serial_has_interrupt_mask(port)) { wr_regl(port, S3C64XX_UINTM, 0xf); @@ -1901,6 +1941,8 @@ static int s3c24xx_serial_probe(struct platform_device *pdev) * and keeps the clock enabled in this case. */ clk_disable_unprepare(ourport->clk); + if (!IS_ERR(ourport->baudclk)) + clk_disable_unprepare(ourport->baudclk); ret = s3c24xx_serial_cpufreq_register(ourport); if (ret < 0) diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c index 268098681856..635178cf3eed 100644 --- a/drivers/tty/serial/sc16is7xx.c +++ b/drivers/tty/serial/sc16is7xx.c @@ -1187,9 +1187,7 @@ static int sc16is7xx_probe(struct device *dev, return PTR_ERR(regmap); /* Alloc port structure */ - s = devm_kzalloc(dev, sizeof(*s) + - sizeof(struct sc16is7xx_one) * devtype->nr_uart, - GFP_KERNEL); + s = devm_kzalloc(dev, struct_size(s, p, devtype->nr_uart), GFP_KERNEL); if (!s) { dev_err(dev, "Error allocating port structure\n"); return -ENOMEM; diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c index 556f50aa1b58..351843f847c0 100644 --- a/drivers/tty/serial/serial_core.c +++ b/drivers/tty/serial/serial_core.c @@ -2844,7 +2844,7 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *uport) */ tty_dev = tty_port_register_device_attr_serdev(port, drv->tty_driver, uport->line, uport->dev, port, uport->tty_groups); - if (likely(!IS_ERR(tty_dev))) { + if (!IS_ERR(tty_dev)) { device_set_wakeup_capable(tty_dev, 1); } else { dev_err(uport->dev, "Cannot register tty device on line %d\n", diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c index 64bbeb7d7e0c..060fcd42b6d5 100644 --- a/drivers/tty/serial/sh-sci.c +++ b/drivers/tty/serial/sh-sci.c @@ -1243,12 +1243,22 @@ static int sci_dma_rx_find_active(struct sci_port *s) return -1; } -static void sci_rx_dma_release(struct sci_port *s) +static void sci_dma_rx_chan_invalidate(struct sci_port *s) +{ + unsigned int i; + + s->chan_rx = NULL; + for (i = 0; i < ARRAY_SIZE(s->cookie_rx); i++) + s->cookie_rx[i] = -EINVAL; + s->active_rx = 0; +} + +static void sci_dma_rx_release(struct sci_port *s) { struct dma_chan *chan = s->chan_rx_saved; - s->chan_rx_saved = s->chan_rx = NULL; - s->cookie_rx[0] = s->cookie_rx[1] = -EINVAL; + s->chan_rx_saved = NULL; + sci_dma_rx_chan_invalidate(s); dmaengine_terminate_sync(chan); dma_free_coherent(chan->device->dev, s->buf_len_rx * 2, s->rx_buf[0], sg_dma_address(&s->sg_rx[0])); @@ -1264,6 +1274,20 @@ static void start_hrtimer_us(struct hrtimer *hrt, unsigned long usec) hrtimer_start(hrt, t, HRTIMER_MODE_REL); } +static void sci_dma_rx_reenable_irq(struct sci_port *s) +{ + struct uart_port *port = &s->port; + u16 scr; + + /* Direct new serial port interrupts back to CPU */ + scr = serial_port_in(port, SCSCR); + if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { + scr &= ~SCSCR_RDRQE; + enable_irq(s->irqs[SCIx_RXI_IRQ]); + } + serial_port_out(port, SCSCR, scr | SCSCR_RIE); +} + static void sci_dma_rx_complete(void *arg) { struct sci_port *s = arg; @@ -1313,12 +1337,13 @@ fail: dev_warn(port->dev, "Failed submitting Rx DMA descriptor\n"); /* Switch to PIO */ spin_lock_irqsave(&port->lock, flags); - s->chan_rx = NULL; - sci_start_rx(port); + dmaengine_terminate_async(chan); + sci_dma_rx_chan_invalidate(s); + sci_dma_rx_reenable_irq(s); spin_unlock_irqrestore(&port->lock, flags); } -static void sci_tx_dma_release(struct sci_port *s) +static void sci_dma_tx_release(struct sci_port *s) { struct dma_chan *chan = s->chan_tx_saved; @@ -1331,7 +1356,7 @@ static void sci_tx_dma_release(struct sci_port *s) dma_release_channel(chan); } -static int sci_submit_rx(struct sci_port *s, bool port_lock_held) +static int sci_dma_rx_submit(struct sci_port *s, bool port_lock_held) { struct dma_chan *chan = s->chan_rx; struct uart_port *port = &s->port; @@ -1367,17 +1392,14 @@ fail: spin_lock_irqsave(&port->lock, flags); if (i) dmaengine_terminate_async(chan); - for (i = 0; i < 2; i++) - s->cookie_rx[i] = -EINVAL; - s->active_rx = 0; - s->chan_rx = NULL; + sci_dma_rx_chan_invalidate(s); sci_start_rx(port); if (!port_lock_held) spin_unlock_irqrestore(&port->lock, flags); return -EAGAIN; } -static void work_fn_tx(struct work_struct *work) +static void sci_dma_tx_work_fn(struct work_struct *work) { struct sci_port *s = container_of(work, struct sci_port, work_tx); struct dma_async_tx_descriptor *desc; @@ -1436,7 +1458,7 @@ switch_to_pio: return; } -static enum hrtimer_restart rx_timer_fn(struct hrtimer *t) +static enum hrtimer_restart sci_dma_rx_timer_fn(struct hrtimer *t) { struct sci_port *s = container_of(t, struct sci_port, rx_timer); struct dma_chan *chan = s->chan_rx; @@ -1446,7 +1468,6 @@ static enum hrtimer_restart rx_timer_fn(struct hrtimer *t) unsigned long flags; unsigned int read; int active, count; - u16 scr; dev_dbg(port->dev, "DMA Rx timed out\n"); @@ -1494,15 +1515,9 @@ static enum hrtimer_restart rx_timer_fn(struct hrtimer *t) } if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) - sci_submit_rx(s, true); + sci_dma_rx_submit(s, true); - /* Direct new serial port interrupts back to CPU */ - scr = serial_port_in(port, SCSCR); - if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { - scr &= ~SCSCR_RDRQE; - enable_irq(s->irqs[SCIx_RXI_IRQ]); - } - serial_port_out(port, SCSCR, scr | SCSCR_RIE); + sci_dma_rx_reenable_irq(s); spin_unlock_irqrestore(&port->lock, flags); @@ -1580,7 +1595,7 @@ static void sci_request_dma(struct uart_port *port) __func__, UART_XMIT_SIZE, port->state->xmit.buf, &s->tx_dma_addr); - INIT_WORK(&s->work_tx, work_fn_tx); + INIT_WORK(&s->work_tx, sci_dma_tx_work_fn); s->chan_tx_saved = s->chan_tx = chan; } } @@ -1615,12 +1630,12 @@ static void sci_request_dma(struct uart_port *port) } hrtimer_init(&s->rx_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL); - s->rx_timer.function = rx_timer_fn; + s->rx_timer.function = sci_dma_rx_timer_fn; s->chan_rx_saved = s->chan_rx = chan; if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) - sci_submit_rx(s, false); + sci_dma_rx_submit(s, false); } } @@ -1629,9 +1644,9 @@ static void sci_free_dma(struct uart_port *port) struct sci_port *s = to_sci_port(port); if (s->chan_tx_saved) - sci_tx_dma_release(s); + sci_dma_tx_release(s); if (s->chan_rx_saved) - sci_rx_dma_release(s); + sci_dma_rx_release(s); } static void sci_flush_buffer(struct uart_port *port) @@ -1669,7 +1684,7 @@ static irqreturn_t sci_rx_interrupt(int irq, void *ptr) disable_irq_nosync(irq); scr |= SCSCR_RDRQE; } else { - if (sci_submit_rx(s, false) < 0) + if (sci_dma_rx_submit(s, false) < 0) goto handle_pio; scr &= ~SCSCR_RIE; diff --git a/drivers/tty/serial/sprd_serial.c b/drivers/tty/serial/sprd_serial.c index 4287ca305b6b..1891a45ac05d 100644 --- a/drivers/tty/serial/sprd_serial.c +++ b/drivers/tty/serial/sprd_serial.c @@ -371,7 +371,7 @@ static void sprd_set_termios(struct uart_port *port, /* ask the core to calculate the divisor for us */ baud = uart_get_baud_rate(port, termios, old, 0, SPRD_BAUD_IO_LIMIT); - quot = (unsigned int)((port->uartclk + baud / 2) / baud); + quot = port->uartclk / baud; /* set data length */ switch (termios->c_cflag & CSIZE) { diff --git a/drivers/tty/serial/tegra-tcu.c b/drivers/tty/serial/tegra-tcu.c new file mode 100644 index 000000000000..aaf8748a6147 --- /dev/null +++ b/drivers/tty/serial/tegra-tcu.c @@ -0,0 +1,298 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2018, NVIDIA CORPORATION. All rights reserved. + */ + +#include <linux/console.h> +#include <linux/mailbox_client.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/serial.h> +#include <linux/serial_core.h> +#include <linux/slab.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> + +#define TCU_MBOX_BYTE(i, x) ((x) << (i * 8)) +#define TCU_MBOX_BYTE_V(x, i) (((x) >> (i * 8)) & 0xff) +#define TCU_MBOX_NUM_BYTES(x) ((x) << 24) +#define TCU_MBOX_NUM_BYTES_V(x) (((x) >> 24) & 0x3) + +struct tegra_tcu { + struct uart_driver driver; +#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE) + struct console console; +#endif + struct uart_port port; + + struct mbox_client tx_client, rx_client; + struct mbox_chan *tx, *rx; +}; + +static unsigned int tegra_tcu_uart_tx_empty(struct uart_port *port) +{ + return TIOCSER_TEMT; +} + +static void tegra_tcu_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ +} + +static unsigned int tegra_tcu_uart_get_mctrl(struct uart_port *port) +{ + return 0; +} + +static void tegra_tcu_uart_stop_tx(struct uart_port *port) +{ +} + +static void tegra_tcu_write_one(struct tegra_tcu *tcu, u32 value, + unsigned int count) +{ + void *msg; + + value |= TCU_MBOX_NUM_BYTES(count); + msg = (void *)(unsigned long)value; + mbox_send_message(tcu->tx, msg); + mbox_flush(tcu->tx, 1000); +} + +static void tegra_tcu_write(struct tegra_tcu *tcu, const char *s, + unsigned int count) +{ + unsigned int written = 0, i = 0; + bool insert_nl = false; + u32 value = 0; + + while (i < count) { + if (insert_nl) { + value |= TCU_MBOX_BYTE(written++, '\n'); + insert_nl = false; + i++; + } else if (s[i] == '\n') { + value |= TCU_MBOX_BYTE(written++, '\r'); + insert_nl = true; + } else { + value |= TCU_MBOX_BYTE(written++, s[i++]); + } + + if (written == 3) { + tegra_tcu_write_one(tcu, value, 3); + value = written = 0; + } + } + + if (written) + tegra_tcu_write_one(tcu, value, written); +} + +static void tegra_tcu_uart_start_tx(struct uart_port *port) +{ + struct tegra_tcu *tcu = port->private_data; + struct circ_buf *xmit = &port->state->xmit; + unsigned long count; + + for (;;) { + count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); + if (!count) + break; + + tegra_tcu_write(tcu, &xmit->buf[xmit->tail], count); + xmit->tail = (xmit->tail + count) & (UART_XMIT_SIZE - 1); + } + + uart_write_wakeup(port); +} + +static void tegra_tcu_uart_stop_rx(struct uart_port *port) +{ +} + +static void tegra_tcu_uart_break_ctl(struct uart_port *port, int ctl) +{ +} + +static int tegra_tcu_uart_startup(struct uart_port *port) +{ + return 0; +} + +static void tegra_tcu_uart_shutdown(struct uart_port *port) +{ +} + +static void tegra_tcu_uart_set_termios(struct uart_port *port, + struct ktermios *new, + struct ktermios *old) +{ +} + +static const struct uart_ops tegra_tcu_uart_ops = { + .tx_empty = tegra_tcu_uart_tx_empty, + .set_mctrl = tegra_tcu_uart_set_mctrl, + .get_mctrl = tegra_tcu_uart_get_mctrl, + .stop_tx = tegra_tcu_uart_stop_tx, + .start_tx = tegra_tcu_uart_start_tx, + .stop_rx = tegra_tcu_uart_stop_rx, + .break_ctl = tegra_tcu_uart_break_ctl, + .startup = tegra_tcu_uart_startup, + .shutdown = tegra_tcu_uart_shutdown, + .set_termios = tegra_tcu_uart_set_termios, +}; + +#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE) +static void tegra_tcu_console_write(struct console *cons, const char *s, + unsigned int count) +{ + struct tegra_tcu *tcu = container_of(cons, struct tegra_tcu, console); + + tegra_tcu_write(tcu, s, count); +} + +static int tegra_tcu_console_setup(struct console *cons, char *options) +{ + return 0; +} +#endif + +static void tegra_tcu_receive(struct mbox_client *cl, void *msg) +{ + struct tegra_tcu *tcu = container_of(cl, struct tegra_tcu, rx_client); + struct tty_port *port = &tcu->port.state->port; + u32 value = (u32)(unsigned long)msg; + unsigned int num_bytes, i; + + num_bytes = TCU_MBOX_NUM_BYTES_V(value); + + for (i = 0; i < num_bytes; i++) + tty_insert_flip_char(port, TCU_MBOX_BYTE_V(value, i), + TTY_NORMAL); + + tty_flip_buffer_push(port); +} + +static int tegra_tcu_probe(struct platform_device *pdev) +{ + struct uart_port *port; + struct tegra_tcu *tcu; + int err; + + tcu = devm_kzalloc(&pdev->dev, sizeof(*tcu), GFP_KERNEL); + if (!tcu) + return -ENOMEM; + + tcu->tx_client.dev = &pdev->dev; + tcu->rx_client.dev = &pdev->dev; + tcu->rx_client.rx_callback = tegra_tcu_receive; + + tcu->tx = mbox_request_channel_byname(&tcu->tx_client, "tx"); + if (IS_ERR(tcu->tx)) { + err = PTR_ERR(tcu->tx); + dev_err(&pdev->dev, "failed to get tx mailbox: %d\n", err); + return err; + } + + tcu->rx = mbox_request_channel_byname(&tcu->rx_client, "rx"); + if (IS_ERR(tcu->rx)) { + err = PTR_ERR(tcu->rx); + dev_err(&pdev->dev, "failed to get rx mailbox: %d\n", err); + goto free_tx; + } + +#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE) + /* setup the console */ + strcpy(tcu->console.name, "ttyTCU"); + tcu->console.device = uart_console_device; + tcu->console.flags = CON_PRINTBUFFER | CON_ANYTIME; + tcu->console.index = -1; + tcu->console.write = tegra_tcu_console_write; + tcu->console.setup = tegra_tcu_console_setup; + tcu->console.data = &tcu->driver; +#endif + + /* setup the driver */ + tcu->driver.owner = THIS_MODULE; + tcu->driver.driver_name = "tegra-tcu"; + tcu->driver.dev_name = "ttyTCU"; +#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE) + tcu->driver.cons = &tcu->console; +#endif + tcu->driver.nr = 1; + + err = uart_register_driver(&tcu->driver); + if (err) { + dev_err(&pdev->dev, "failed to register UART driver: %d\n", + err); + goto free_rx; + } + + /* setup the port */ + port = &tcu->port; + spin_lock_init(&port->lock); + port->dev = &pdev->dev; + port->type = PORT_TEGRA_TCU; + port->ops = &tegra_tcu_uart_ops; + port->fifosize = 1; + port->iotype = UPIO_MEM; + port->flags = UPF_BOOT_AUTOCONF; + port->private_data = tcu; + + err = uart_add_one_port(&tcu->driver, port); + if (err) { + dev_err(&pdev->dev, "failed to add UART port: %d\n", err); + goto unregister_uart; + } + + platform_set_drvdata(pdev, tcu); +#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE) + register_console(&tcu->console); +#endif + + return 0; + +unregister_uart: + uart_unregister_driver(&tcu->driver); +free_rx: + mbox_free_channel(tcu->rx); +free_tx: + mbox_free_channel(tcu->tx); + + return err; +} + +static int tegra_tcu_remove(struct platform_device *pdev) +{ + struct tegra_tcu *tcu = platform_get_drvdata(pdev); + +#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE) + unregister_console(&tcu->console); +#endif + uart_remove_one_port(&tcu->driver, &tcu->port); + uart_unregister_driver(&tcu->driver); + mbox_free_channel(tcu->rx); + mbox_free_channel(tcu->tx); + + return 0; +} + +static const struct of_device_id tegra_tcu_match[] = { + { .compatible = "nvidia,tegra194-tcu" }, + { } +}; + +static struct platform_driver tegra_tcu_driver = { + .driver = { + .name = "tegra-tcu", + .of_match_table = tegra_tcu_match, + }, + .probe = tegra_tcu_probe, + .remove = tegra_tcu_remove, +}; +module_platform_driver(tegra_tcu_driver); + +MODULE_AUTHOR("Mikko Perttunen <mperttunen@nvidia.com>"); +MODULE_LICENSE("GPL v2"); +MODULE_DESCRIPTION("NVIDIA Tegra Combined UART driver"); diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c index 094f2958cb2b..74089f5e5b53 100644 --- a/drivers/tty/serial/xilinx_uartps.c +++ b/drivers/tty/serial/xilinx_uartps.c @@ -364,7 +364,13 @@ static irqreturn_t cdns_uart_isr(int irq, void *dev_id) cdns_uart_handle_tx(dev_id); isrstatus &= ~CDNS_UART_IXR_TXEMPTY; } - if (isrstatus & CDNS_UART_IXR_RXMASK) + + /* + * Skip RX processing if RX is disabled as RXEMPTY will never be set + * as read bytes will not be removed from the FIFO. + */ + if (isrstatus & CDNS_UART_IXR_RXMASK && + !(readl(port->membase + CDNS_UART_CR) & CDNS_UART_CR_RX_DIS)) cdns_uart_handle_rx(dev_id, isrstatus); spin_unlock(&port->lock); @@ -1547,27 +1553,33 @@ static int cdns_uart_probe(struct platform_device *pdev) } cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "pclk"); + if (PTR_ERR(cdns_uart_data->pclk) == -EPROBE_DEFER) { + rc = PTR_ERR(cdns_uart_data->pclk); + goto err_out_unregister_driver; + } + if (IS_ERR(cdns_uart_data->pclk)) { cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "aper_clk"); - if (!IS_ERR(cdns_uart_data->pclk)) - dev_err(&pdev->dev, "clock name 'aper_clk' is deprecated.\n"); + if (IS_ERR(cdns_uart_data->pclk)) { + rc = PTR_ERR(cdns_uart_data->pclk); + goto err_out_unregister_driver; + } + dev_err(&pdev->dev, "clock name 'aper_clk' is deprecated.\n"); } - if (IS_ERR(cdns_uart_data->pclk)) { - dev_err(&pdev->dev, "pclk clock not found.\n"); - rc = PTR_ERR(cdns_uart_data->pclk); + + cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "uart_clk"); + if (PTR_ERR(cdns_uart_data->uartclk) == -EPROBE_DEFER) { + rc = PTR_ERR(cdns_uart_data->uartclk); goto err_out_unregister_driver; } - cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "uart_clk"); if (IS_ERR(cdns_uart_data->uartclk)) { cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "ref_clk"); - if (!IS_ERR(cdns_uart_data->uartclk)) - dev_err(&pdev->dev, "clock name 'ref_clk' is deprecated.\n"); - } - if (IS_ERR(cdns_uart_data->uartclk)) { - dev_err(&pdev->dev, "uart_clk clock not found.\n"); - rc = PTR_ERR(cdns_uart_data->uartclk); - goto err_out_unregister_driver; + if (IS_ERR(cdns_uart_data->uartclk)) { + rc = PTR_ERR(cdns_uart_data->uartclk); + goto err_out_unregister_driver; + } + dev_err(&pdev->dev, "clock name 'ref_clk' is deprecated.\n"); } rc = clk_prepare_enable(cdns_uart_data->pclk); diff --git a/drivers/tty/synclink.c b/drivers/tty/synclink.c index d55c858d6058..84f26e43b229 100644 --- a/drivers/tty/synclink.c +++ b/drivers/tty/synclink.c @@ -4325,41 +4325,6 @@ static int mgsl_init_tty(void) return 0; } -/* enumerate user specified ISA adapters - */ -static void mgsl_enum_isa_devices(void) -{ - struct mgsl_struct *info; - int i; - - /* Check for user specified ISA devices */ - - for (i=0 ;(i < MAX_ISA_DEVICES) && io[i] && irq[i]; i++){ - if ( debug_level >= DEBUG_LEVEL_INFO ) - printk("ISA device specified io=%04X,irq=%d,dma=%d\n", - io[i], irq[i], dma[i] ); - - info = mgsl_allocate_device(); - if ( !info ) { - /* error allocating device instance data */ - if ( debug_level >= DEBUG_LEVEL_ERROR ) - printk( "can't allocate device instance data.\n"); - continue; - } - - /* Copy user configuration info to device instance data */ - info->io_base = (unsigned int)io[i]; - info->irq_level = (unsigned int)irq[i]; - info->irq_level = irq_canonicalize(info->irq_level); - info->dma_level = (unsigned int)dma[i]; - info->bus_type = MGSL_BUS_TYPE_ISA; - info->io_addr_size = 16; - info->irq_flags = 0; - - mgsl_add_device( info ); - } -} - static void synclink_cleanup(void) { int rc; @@ -4403,7 +4368,6 @@ static int __init synclink_init(void) printk("%s %s\n", driver_name, driver_version); - mgsl_enum_isa_devices(); if ((rc = pci_register_driver(&synclink_pci_driver)) < 0) printk("%s:failed to register PCI driver, error=%d\n",__FILE__,rc); else @@ -5025,12 +4989,6 @@ static void usc_set_sdlc_mode( struct mgsl_struct *info ) info->mbre_bit = BIT8; outw( BIT8, info->io_base ); /* set Master Bus Enable (DCAR) */ - if (info->bus_type == MGSL_BUS_TYPE_ISA) { - /* Enable DMAEN (Port 7, Bit 14) */ - /* This connects the DMA request signal to the ISA bus */ - usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT15) & ~BIT14)); - } - /* DMA Control Register (DCR) * * <15..14> 10 Priority mode = Alternating Tx/Rx @@ -6007,12 +5965,6 @@ static void usc_set_async_mode( struct mgsl_struct *info ) usc_EnableMasterIrqBit( info ); - if (info->bus_type == MGSL_BUS_TYPE_ISA) { - /* Enable INTEN (Port 6, Bit12) */ - /* This connects the IRQ request signal to the ISA bus */ - usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) & ~BIT12)); - } - if (info->params.loopback) { info->loopback_bits = 0x300; outw(0x0300, info->io_base + CCAR); @@ -6107,12 +6059,6 @@ static void usc_set_sync_mode( struct mgsl_struct *info ) usc_loopback_frame( info ); usc_set_sdlc_mode( info ); - if (info->bus_type == MGSL_BUS_TYPE_ISA) { - /* Enable INTEN (Port 6, Bit12) */ - /* This connects the IRQ request signal to the ISA bus */ - usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) & ~BIT12)); - } - usc_enable_aux_clock(info, info->params.clock_speed); if (info->params.loopback) diff --git a/drivers/tty/sysrq.c b/drivers/tty/sysrq.c index 1f03078ec352..fa0ce7dd9e24 100644 --- a/drivers/tty/sysrq.c +++ b/drivers/tty/sysrq.c @@ -539,7 +539,6 @@ void __handle_sysrq(int key, bool check_mask) */ orig_log_level = console_loglevel; console_loglevel = CONSOLE_LOGLEVEL_DEFAULT; - pr_info("SysRq : "); op_p = __sysrq_get_key_op(key); if (op_p) { @@ -548,14 +547,15 @@ void __handle_sysrq(int key, bool check_mask) * should not) and is the invoked operation enabled? */ if (!check_mask || sysrq_on_mask(op_p->enable_mask)) { - pr_cont("%s\n", op_p->action_msg); + pr_info("%s\n", op_p->action_msg); console_loglevel = orig_log_level; op_p->handler(key); } else { - pr_cont("This sysrq operation is disabled.\n"); + pr_info("This sysrq operation is disabled.\n"); + console_loglevel = orig_log_level; } } else { - pr_cont("HELP : "); + pr_info("HELP : "); /* Only print the help msg once per handler */ for (i = 0; i < ARRAY_SIZE(sysrq_key_table); i++) { if (sysrq_key_table[i]) { diff --git a/drivers/tty/tty_buffer.c b/drivers/tty/tty_buffer.c index 77070c2d1240..ec145a59f199 100644 --- a/drivers/tty/tty_buffer.c +++ b/drivers/tty/tty_buffer.c @@ -26,7 +26,7 @@ * Byte threshold to limit memory consumption for flip buffers. * The actual memory limit is > 2x this amount. */ -#define TTYB_DEFAULT_MEM_LIMIT 65536 +#define TTYB_DEFAULT_MEM_LIMIT (640 * 1024UL) /* * We default to dicing tty buffer allocations to this many characters diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c index 21ffcce16927..5fa250157025 100644 --- a/drivers/tty/tty_io.c +++ b/drivers/tty/tty_io.c @@ -513,6 +513,8 @@ static const struct file_operations hung_up_tty_fops = { static DEFINE_SPINLOCK(redirect_lock); static struct file *redirect; +extern void tty_sysctl_init(void); + /** * tty_wakeup - request more data * @tty: terminal @@ -3483,6 +3485,7 @@ void console_sysfs_notify(void) */ int __init tty_init(void) { + tty_sysctl_init(); cdev_init(&tty_cdev, &tty_fops); if (cdev_add(&tty_cdev, MKDEV(TTYAUX_MAJOR, 0), 1) || register_chrdev_region(MKDEV(TTYAUX_MAJOR, 0), 1, "/dev/tty") < 0) diff --git a/drivers/tty/tty_ldisc.c b/drivers/tty/tty_ldisc.c index 45eda69b150c..e38f104db174 100644 --- a/drivers/tty/tty_ldisc.c +++ b/drivers/tty/tty_ldisc.c @@ -156,6 +156,13 @@ static void put_ldops(struct tty_ldisc_ops *ldops) * takes tty_ldiscs_lock to guard against ldisc races */ +#if defined(CONFIG_LDISC_AUTOLOAD) + #define INITIAL_AUTOLOAD_STATE 1 +#else + #define INITIAL_AUTOLOAD_STATE 0 +#endif +static int tty_ldisc_autoload = INITIAL_AUTOLOAD_STATE; + static struct tty_ldisc *tty_ldisc_get(struct tty_struct *tty, int disc) { struct tty_ldisc *ld; @@ -170,6 +177,8 @@ static struct tty_ldisc *tty_ldisc_get(struct tty_struct *tty, int disc) */ ldops = get_ldops(disc); if (IS_ERR(ldops)) { + if (!capable(CAP_SYS_MODULE) && !tty_ldisc_autoload) + return ERR_PTR(-EPERM); request_module("tty-ldisc-%d", disc); ldops = get_ldops(disc); if (IS_ERR(ldops)) @@ -845,3 +854,41 @@ void tty_ldisc_deinit(struct tty_struct *tty) tty_ldisc_put(tty->ldisc); tty->ldisc = NULL; } + +static int zero; +static int one = 1; +static struct ctl_table tty_table[] = { + { + .procname = "ldisc_autoload", + .data = &tty_ldisc_autoload, + .maxlen = sizeof(tty_ldisc_autoload), + .mode = 0644, + .proc_handler = proc_dointvec, + .extra1 = &zero, + .extra2 = &one, + }, + { } +}; + +static struct ctl_table tty_dir_table[] = { + { + .procname = "tty", + .mode = 0555, + .child = tty_table, + }, + { } +}; + +static struct ctl_table tty_root_table[] = { + { + .procname = "dev", + .mode = 0555, + .child = tty_dir_table, + }, + { } +}; + +void tty_sysctl_init(void) +{ + register_sysctl_table(tty_root_table); +} diff --git a/drivers/tty/vt/vc_screen.c b/drivers/tty/vt/vc_screen.c index 2384ea85ffaf..160f46115aaa 100644 --- a/drivers/tty/vt/vc_screen.c +++ b/drivers/tty/vt/vc_screen.c @@ -80,7 +80,7 @@ struct vcs_poll_data { struct notifier_block notifier; unsigned int cons_num; - bool seen_last_update; + int event; wait_queue_head_t waitq; struct fasync_struct *fasync; }; @@ -93,9 +93,18 @@ vcs_notifier(struct notifier_block *nb, unsigned long code, void *_param) struct vcs_poll_data *poll = container_of(nb, struct vcs_poll_data, notifier); int currcons = poll->cons_num; - - if (code != VT_UPDATE) + int fa_band; + + switch (code) { + case VT_UPDATE: + fa_band = POLL_PRI; + break; + case VT_DEALLOCATE: + fa_band = POLL_HUP; + break; + default: return NOTIFY_DONE; + } if (currcons == 0) currcons = fg_console; @@ -104,9 +113,9 @@ vcs_notifier(struct notifier_block *nb, unsigned long code, void *_param) if (currcons != vc->vc_num) return NOTIFY_DONE; - poll->seen_last_update = false; + poll->event = code; wake_up_interruptible(&poll->waitq); - kill_fasync(&poll->fasync, SIGIO, POLL_IN); + kill_fasync(&poll->fasync, SIGIO, fa_band); return NOTIFY_OK; } @@ -131,6 +140,15 @@ vcs_poll_data_get(struct file *file) poll->cons_num = console(file_inode(file)); init_waitqueue_head(&poll->waitq); poll->notifier.notifier_call = vcs_notifier; + /* + * In order not to lose any update event, we must pretend one might + * have occurred before we have a chance to register our notifier. + * This is also how user space has come to detect which kernels + * support POLLPRI on /dev/vcs* devices i.e. using poll() with + * POLLPRI and a zero timeout. + */ + poll->event = VT_UPDATE; + if (register_vt_notifier(&poll->notifier) != 0) { kfree(poll); return NULL; @@ -261,7 +279,7 @@ vcs_read(struct file *file, char __user *buf, size_t count, loff_t *ppos) poll = file->private_data; if (count && poll) - poll->seen_last_update = true; + poll->event = 0; read = 0; ret = 0; while (count) { @@ -335,8 +353,9 @@ vcs_read(struct file *file, char __user *buf, size_t count, loff_t *ppos) if (p < HEADER_SIZE) { size_t tmp_count; - con_buf0[0] = (char)vc->vc_rows; - con_buf0[1] = (char)vc->vc_cols; + /* clamp header values if they don't fit */ + con_buf0[0] = min(vc->vc_rows, 0xFFu); + con_buf0[1] = min(vc->vc_cols, 0xFFu); getconsxy(vc, con_buf0 + 2); con_buf_start += p; @@ -615,12 +634,21 @@ static __poll_t vcs_poll(struct file *file, poll_table *wait) { struct vcs_poll_data *poll = vcs_poll_data_get(file); - __poll_t ret = DEFAULT_POLLMASK|EPOLLERR|EPOLLPRI; + __poll_t ret = DEFAULT_POLLMASK|EPOLLERR; if (poll) { poll_wait(file, &poll->waitq, wait); - if (poll->seen_last_update) + switch (poll->event) { + case VT_UPDATE: + ret = DEFAULT_POLLMASK|EPOLLPRI; + break; + case VT_DEALLOCATE: + ret = DEFAULT_POLLMASK|EPOLLHUP|EPOLLERR; + break; + case 0: ret = DEFAULT_POLLMASK; + break; + } } return ret; } diff --git a/drivers/tty/vt/vt.c b/drivers/tty/vt/vt.c index bba75560d11e..d34984aa646d 100644 --- a/drivers/tty/vt/vt.c +++ b/drivers/tty/vt/vt.c @@ -935,8 +935,11 @@ static void flush_scrollback(struct vc_data *vc) { WARN_CONSOLE_UNLOCKED(); + set_origin(vc); if (vc->vc_sw->con_flush_scrollback) vc->vc_sw->con_flush_scrollback(vc); + else + vc->vc_sw->con_switch(vc); } /* @@ -1342,6 +1345,8 @@ struct vc_data *vc_deallocate(unsigned int currcons) * VT102 emulator */ +enum { EPecma = 0, EPdec, EPeq, EPgt, EPlt}; + #define set_kbd(vc, x) vt_set_kbd_mode_bit((vc)->vc_num, (x)) #define clr_kbd(vc, x) vt_clr_kbd_mode_bit((vc)->vc_num, (x)) #define is_kbd(vc, x) vt_get_kbd_mode_bit((vc)->vc_num, (x)) @@ -1503,8 +1508,10 @@ static void csi_J(struct vc_data *vc, int vpar) count = ((vc->vc_pos - vc->vc_origin) >> 1) + 1; start = (unsigned short *)vc->vc_origin; break; + case 3: /* include scrollback */ + flush_scrollback(vc); + /* fallthrough */ case 2: /* erase whole display */ - case 3: /* (and scrollback buffer later) */ vc_uniscr_clear_lines(vc, 0, vc->vc_rows); count = vc->vc_cols * vc->vc_rows; start = (unsigned short *)vc->vc_origin; @@ -1513,13 +1520,7 @@ static void csi_J(struct vc_data *vc, int vpar) return; } scr_memsetw(start, vc->vc_video_erase_char, 2 * count); - if (vpar == 3) { - set_origin(vc); - flush_scrollback(vc); - if (con_is_visible(vc)) - update_screen(vc); - } else if (con_should_update(vc)) - do_update_region(vc, (unsigned long) start, count); + update_region(vc, (unsigned long) start, count); vc->vc_need_wrap = 0; } @@ -1628,9 +1629,9 @@ static void rgb_background(struct vc_data *vc, const struct rgb *c) /* * ITU T.416 Higher colour modes. They break the usual properties of SGR codes - * and thus need to be detected and ignored by hand. Strictly speaking, that - * standard also wants : rather than ; as separators, contrary to ECMA-48, but - * no one produces such codes and almost no one accepts them. + * and thus need to be detected and ignored by hand. That standard also + * wants : rather than ; as separators but sequences containing : are currently + * completely ignored by the parser. * * Subcommands 3 (CMY) and 4 (CMYK) are so insane there's no point in * supporting them. @@ -1815,7 +1816,7 @@ static void set_mode(struct vc_data *vc, int on_off) int i; for (i = 0; i <= vc->vc_npar; i++) - if (vc->vc_ques) { + if (vc->vc_priv == EPdec) { switch(vc->vc_par[i]) { /* DEC private modes set/reset */ case 1: /* Cursor keys send ^[Ox/^[[x */ if (on_off) @@ -2022,7 +2023,7 @@ static void restore_cur(struct vc_data *vc) } enum { ESnormal, ESesc, ESsquare, ESgetpars, ESfunckey, - EShash, ESsetG0, ESsetG1, ESpercent, ESignore, ESnonstd, + EShash, ESsetG0, ESsetG1, ESpercent, EScsiignore, ESnonstd, ESpalette, ESosc }; /* console_lock is held (except via vc_init()) */ @@ -2031,7 +2032,7 @@ static void reset_terminal(struct vc_data *vc, int do_clear) vc->vc_top = 0; vc->vc_bottom = vc->vc_rows; vc->vc_state = ESnormal; - vc->vc_ques = 0; + vc->vc_priv = EPecma; vc->vc_translate = set_translate(LAT1_MAP, vc); vc->vc_G0_charset = LAT1_MAP; vc->vc_G1_charset = GRAF_MAP; @@ -2112,6 +2113,7 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c) lf(vc); if (!is_kbd(vc, lnm)) return; + /* fall through */ case 13: cr(vc); return; @@ -2234,9 +2236,22 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c) vc->vc_state=ESfunckey; return; } - vc->vc_ques = (c == '?'); - if (vc->vc_ques) + switch (c) { + case '?': + vc->vc_priv = EPdec; + return; + case '>': + vc->vc_priv = EPgt; + return; + case '=': + vc->vc_priv = EPeq; return; + case '<': + vc->vc_priv = EPlt; + return; + } + vc->vc_priv = EPecma; + /* fall through */ case ESgetpars: if (c == ';' && vc->vc_npar < NPAR - 1) { vc->vc_npar++; @@ -2246,16 +2261,22 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c) vc->vc_par[vc->vc_npar] += c - '0'; return; } + if (c >= 0x20 && c <= 0x3f) { /* 0x2x, 0x3a and 0x3c - 0x3f */ + vc->vc_state = EScsiignore; + return; + } vc->vc_state = ESnormal; switch(c) { case 'h': - set_mode(vc, 1); + if (vc->vc_priv <= EPdec) + set_mode(vc, 1); return; case 'l': - set_mode(vc, 0); + if (vc->vc_priv <= EPdec) + set_mode(vc, 0); return; case 'c': - if (vc->vc_ques) { + if (vc->vc_priv == EPdec) { if (vc->vc_par[0]) vc->vc_cursor_type = vc->vc_par[0] | (vc->vc_par[1] << 8) | (vc->vc_par[2] << 16); else @@ -2264,7 +2285,7 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c) } break; case 'm': - if (vc->vc_ques) { + if (vc->vc_priv == EPdec) { clear_selection(); if (vc->vc_par[0]) vc->vc_complement_mask = vc->vc_par[0] << 8 | vc->vc_par[1]; @@ -2274,7 +2295,7 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c) } break; case 'n': - if (!vc->vc_ques) { + if (vc->vc_priv == EPecma) { if (vc->vc_par[0] == 5) status_report(tty); else if (vc->vc_par[0] == 6) @@ -2282,8 +2303,8 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c) } return; } - if (vc->vc_ques) { - vc->vc_ques = 0; + if (vc->vc_priv != EPecma) { + vc->vc_priv = EPecma; return; } switch(c) { @@ -2406,6 +2427,11 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c) return; } return; + case EScsiignore: + if (c >= 20 && c <= 0x3f) + return; + vc->vc_state = ESnormal; + return; case ESpercent: vc->vc_state = ESnormal; switch (c) { @@ -4591,8 +4617,9 @@ EXPORT_SYMBOL_GPL(screen_pos); void getconsxy(struct vc_data *vc, unsigned char *p) { - p[0] = vc->vc_x; - p[1] = vc->vc_y; + /* clamp values if they don't fit */ + p[0] = min(vc->vc_x, 0xFFu); + p[1] = min(vc->vc_y, 0xFFu); } void putconsxy(struct vc_data *vc, unsigned char *p) diff --git a/include/linux/console_struct.h b/include/linux/console_struct.h index ab137f97ecbd..ed798e114663 100644 --- a/include/linux/console_struct.h +++ b/include/linux/console_struct.h @@ -119,7 +119,7 @@ struct vc_data { unsigned int vc_s_blink : 1; unsigned int vc_s_reverse : 1; /* misc */ - unsigned int vc_ques : 1; + unsigned int vc_priv : 3; unsigned int vc_need_wrap : 1; unsigned int vc_can_do_color : 1; unsigned int vc_report_mouse : 2; diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h index df4a7534e239..6009ee2c2e99 100644 --- a/include/uapi/linux/serial_core.h +++ b/include/uapi/linux/serial_core.h @@ -79,6 +79,9 @@ /* Nuvoton UART */ #define PORT_NPCM 40 +/* NVIDIA Tegra Combined UART */ +#define PORT_TEGRA_TCU 41 + /* Intel EG20 */ #define PORT_PCH_8LINE 44 #define PORT_PCH_2LINE 45 |