Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree changes from Arnd Bergmann:
 "A large part of the arm-soc patches are nowadays DT changes, adding
  support for new SoCs, boards and devices without changing kernel
  source.  The plan is still to move the devicetree files out of the
  kernel tree and reduce the amount of churn going on here, but we keep
  finding reasons to delay doing that.

  Changes are really all over the place, with little sticking out
  particularly.  We have contributions from a total of 116 people in
  this branch.

  Unfortunately, the size of this branch also causes a significant
  number of conflicts at the moment, typically when subsystem
  maintainers merge patches that change the driver at the same time as
  the dts files.  In most cases this could be avoided because the dts
  changes are supposed to be compatible in both ways, and we are asking
  everyone to send ARM dts changes through our tree only"

* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
  dts: stmmac: Document the clocks property in the stmmac base document
  dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
  ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
  ARM: STi: stih416: Add support for the FSM Serial Flash Controller
  ARM: tegra: fix Dalmore pinctrl configuration
  ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
  ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
  ARM: dts: Build all keystone dt blobs
  ARM: dts: keystone: Fix control register range for clktsip
  ARM: dts: keystone: Fix domain register range for clkfftc1
  ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
  ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
  ARM: dts: bcm21664: Add device tree files.
  ARM: DT: bcm21664: Device tree bindings
  ARM: efm32: properly namespace i2c location property
  ARM: efm32: fix unit address part in USART2 device nodes' names
  ARM: mvebu: Enable NAND controller in Armada 385-DB
  ARM: mvebu: Add support for NAND controller in Armada 38x SoC
  ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
  ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
  ...

1 files changed, 87 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt
new file mode 100644
index 000000000000..0f813dec5e08
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt
@@ -0,0 +1,87 @@
+* AT91's Analog to Digital Converter (ADC)
+
+Required properties:
+  - compatible: Should be "atmel,<chip>-adc"
+    <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5"
+  - reg: Should contain ADC registers location and length
+  - interrupts: Should contain the IRQ line for the ADC
+  - clock-names: tuple listing input clock names.
+	Required elements: "adc_clk", "adc_op_clk".
+  - clocks: phandles to input clocks.
+  - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this
+    device
+  - atmel,adc-startup-time: Startup Time of the ADC in microseconds as
+    defined in the datasheet
+  - atmel,adc-vref: Reference voltage in millivolts for the conversions
+  - atmel,adc-res: List of resolutions in bits supported by the ADC. List size
+		   must be two at least.
+  - atmel,adc-res-names: Contains one identifier string for each resolution
+			 in atmel,adc-res property. "lowres" and "highres"
+			 identifiers are required.
+
+Optional properties:
+  - atmel,adc-use-external-triggers: Boolean to enable the external triggers
+  - atmel,adc-use-res: String corresponding to an identifier from
+		       atmel,adc-res-names property. If not specified, the highest
+		       resolution will be used.
+  - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion
+  - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds
+  - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this
+                        value is set, then the adc driver will enable touchscreen
+                        support.
+    NOTE: when adc touchscreen is enabled, the adc hardware trigger will be
+          disabled. Since touchscreen will occupy the trigger register.
+  - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It
+                                     makes touch detection more precise.
+
+Optional trigger Nodes:
+  - Required properties:
+    * trigger-name: Name of the trigger exposed to the user
+    * trigger-value: Value to put in the Trigger register
+      to activate this trigger
+  - Optional properties:
+    * trigger-external: Is the trigger an external trigger?
+
+Examples:
+adc0: adc@fffb0000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "atmel,at91sam9260-adc";
+	reg = <0xfffb0000 0x100>;
+	interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+	clocks = <&adc_clk>, <&adc_op_clk>;
+	clock-names = "adc_clk", "adc_op_clk";
+	atmel,adc-channels-used = <0xff>;
+	atmel,adc-startup-time = <40>;
+	atmel,adc-use-external-triggers;
+	atmel,adc-vref = <3300>;
+	atmel,adc-res = <8 10>;
+	atmel,adc-res-names = "lowres", "highres";
+	atmel,adc-use-res = "lowres";
+
+	trigger@0 {
+		reg = <0>;
+		trigger-name = "external-rising";
+		trigger-value = <0x1>;
+		trigger-external;
+	};
+	trigger@1 {
+		reg = <1>;
+		trigger-name = "external-falling";
+		trigger-value = <0x2>;
+		trigger-external;
+	};
+
+	trigger@2 {
+		reg = <2>;
+		trigger-name = "external-any";
+		trigger-value = <0x3>;
+		trigger-external;
+	};
+
+	trigger@3 {
+		reg = <3>;
+		trigger-name = "continuous";
+		trigger-value = <0x6>;
+	};
+};