Merge tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB updates from Greg KH:
 "Here's the big USB patchset for 3.18-rc1.  Also in here is the PHY
  tree, as it seems to fit well with the USB tree for various reasons...

  Anyway, lots of little changes in here, all over the place, full
  details in the changelog

  All have been in the linux-next tree for a while with no issues"

* tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (244 commits)
  USB: host: st: fix typo 'CONFIG_USB_EHCI_HCD_ST'
  uas: Reduce number of function arguments for uas_alloc_foo functions
  xhci: Allow xHCI drivers to be built as separate modules
  xhci: Export symbols used by host-controller drivers
  xhci: Check for XHCI_COMP_MODE_QUIRK when disabling D3cold
  xhci: Introduce xhci_init_driver()
  usb: hcd: add generic PHY support
  usb: rename phy to usb_phy in HCD
  usb: gadget: uvc: fix up uvcg_v4l2_get_unmapped_area typo
  USB: host: st: fix ehci/ohci driver selection
  usb: host: ehci-exynos: Remove unnecessary usb-phy support
  usb: core: return -ENOTSUPP for all targeted hosts
  USB: Remove .owner field for driver
  usb: core: log higher level message on malformed LANGID descriptor
  usb: Add LED triggers for USB activity
  usb: Rename usb-common.c
  usb: gadget: Refactor request completion
  usb: gadget: Introduce usb_gadget_giveback_request()
  usb: dwc2/gadget: move phy bus legth initialization
  phy: remove .owner field for drivers using module_platform_driver
  ...

17 files changed, 413 insertions, 4 deletions

diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
new file mode 100644
index 000000000000..1ef8228db73b
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
@@ -0,0 +1,30 @@
+ST STiH407 USB PHY controller
+
+This file documents the dt bindings for the usb picoPHY driver which is the PHY for both USB2 and USB3
+host controllers (when controlling usb2/1.1 devices) available on STiH407 SoC family from STMicroelectronics.
+
+Required properties:
+- compatible		: should be "st,stih407-usb2-phy"
+- reg			: contain the offset and length of the system configuration registers
+			  used as glue logic to control & parameter phy
+- reg-names		: the names of the system configuration registers in "reg", should be "param" and "reg"
+- st,syscfg		: sysconfig register to manage phy parameter at driver level
+- resets		: list of phandle and reset specifier pairs. There should be two entries, one
+			  for the whole phy and one for the port
+- reset-names		: list of reset signal names. Should be "global" and "port"
+See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
+See: Documentation/devicetree/bindings/reset/reset.txt
+
+Example:
+
+usb2_picophy0: usbpicophy@f8 {
+	compatible	= "st,stih407-usb2-phy";
+	reg		= <0xf8 0x04>,	/* syscfg 5062 */
+			  <0xf4 0x04>;	/* syscfg 5061 */
+	reg-names	= "param", "ctrl";
+	#phy-cells	= <0>;
+	st,syscfg	= <&syscfg_core>;
+	resets		= <&softreset STIH407_PICOPHY_SOFTRESET>,
+			  <&picophyreset STIH407_PICOPHY0_RESET>;
+	reset-names	= "global", "port";
+};
diff --git a/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt
new file mode 100644
index 000000000000..00944a05ee6b
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt
@@ -0,0 +1,24 @@
+STMicroelectronics STiH41x USB PHY binding
+------------------------------------------
+
+This file contains documentation for the usb phy found in STiH415/6 SoCs from
+STMicroelectronics.
+
+Required properties:
+- compatible	: should be "st,stih416-usb-phy" or "st,stih415-usb-phy"
+- st,syscfg	: should be a phandle of the syscfg node
+- clock-names	: must contain "osc_phy"
+- clocks	: must contain an entry for each name in clock-names.
+See: Documentation/devicetree/bindings/clock/clock-bindings.txt
+- #phy-cells	: must be 0 for this phy
+See: Documentation/devicetree/bindings/phy/phy-bindings.txt
+
+Example:
+
+usb2_phy: usb2phy@0 {
+	compatible	= "st,stih416-usb-phy";
+	#phy-cell	= <0>;
+	st,syscfg	= <&syscfg_rear>;
+	clocks		= <&clk_sysin>;
+	clock-names	= "osc_phy";
+};
diff --git a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
new file mode 100644
index 000000000000..86f2dbe07ed4
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
@@ -0,0 +1,39 @@
+Qualcomm DWC3 HS AND SS PHY CONTROLLER
+--------------------------------------
+
+DWC3 PHY nodes are defined to describe on-chip Synopsis Physical layer
+controllers.  Each DWC3 PHY controller should have its own node.
+
+Required properties:
+- compatible: should contain one of the following:
+	- "qcom,dwc3-hs-usb-phy" for High Speed Synopsis PHY controller
+	- "qcom,dwc3-ss-usb-phy" for Super Speed Synopsis PHY controller
+- reg: offset and length of the DWC3 PHY controller register set
+- #phy-cells: must be zero
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+- clock-names: Should contain "ref" for the PHY reference clock
+
+Optional clocks:
+  "xo"		External reference clock
+
+Example:
+		phy@100f8800 {
+			compatible = "qcom,dwc3-hs-usb-phy";
+			reg = <0x100f8800 0x30>;
+			clocks = <&gcc USB30_0_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "ok";
+		};
+
+		phy@100f8830 {
+			compatible = "qcom,dwc3-ss-usb-phy";
+			reg = <0x100f8830 0x30>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "ok";
+		};
diff --git a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt
new file mode 100644
index 000000000000..00fc52a034b7
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt
@@ -0,0 +1,51 @@
+* Renesas R-Car generation 2 USB PHY
+
+This file provides information on what the device node for the R-Car generation
+2 USB PHY contains.
+
+Required properties:
+- compatible: "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC.
+	      "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC.
+- reg: offset and length of the register block.
+- #address-cells: number of address cells for the USB channel subnodes, must
+		  be <1>.
+- #size-cells: number of size cells for the USB channel subnodes, must be <0>.
+- clocks: clock phandle and specifier pair.
+- clock-names: string, clock input name, must be "usbhs".
+
+The USB PHY device tree node should have the subnodes corresponding to the USB
+channels. These subnodes must contain the following properties:
+- reg: the USB controller selector; see the table below for the values.
+- #phy-cells: see phy-bindings.txt in the same directory, must be <1>.
+
+The phandle's argument in the PHY specifier is the USB controller selector for
+the USB channel; see the selector meanings below:
+
++-----------+---------------+---------------+
+|\ Selector |               |               |
++ --------- +       0       |       1       |
+| Channel  \|               |               |
++-----------+---------------+---------------+
+| 0         | PCI EHCI/OHCI | HS-USB        |
+| 2         | PCI EHCI/OHCI | xHCI          |
++-----------+---------------+---------------+
+
+Example (Lager board):
+
+	usb-phy@e6590100 {
+		compatible = "renesas,usb-phy-r8a7790";
+		reg = <0 0xe6590100 0 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
+		clock-names = "usbhs";
+
+		usb-channel@0 {
+			reg = <0>;
+			#phy-cells = <1>;
+		};
+		usb-channel@2 {
+			reg = <2>;
+			#phy-cells = <1>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
index 7a6feea2a48b..15e0f2c7130f 100644
--- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
+++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
@@ -17,8 +17,11 @@ Samsung EXYNOS SoC series Display Port PHY
 -------------------------------------------------
 
 Required properties:
-- compatible : should be "samsung,exynos5250-dp-video-phy";
-- reg : offset and length of the Display Port PHY register set;
+- compatible : should be one of the following supported values:
+	 - "samsung,exynos5250-dp-video-phy"
+	 - "samsung,exynos5420-dp-video-phy"
+- samsung,pmu-syscon: phandle for PMU system controller interface, used to
+		      control pmu registers for power isolation.
 - #phy-cells : from the generic PHY bindings, must be 0;
 
 Samsung S5P/EXYNOS SoC series USB PHY
diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt
index 1bae71e9ad47..38a548001e3a 100644
--- a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt
+++ b/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt
@@ -19,6 +19,7 @@ Optional properties:
 - disable-over-current: disable over current detect
 - external-vbus-divider: enables off-chip resistor divider for Vbus
 - maximum-speed: limit the maximum connection speed to "full-speed".
+- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts
 
 Examples:
 usb@02184000 { /* USB OTG */
@@ -30,4 +31,5 @@ usb@02184000 { /* USB OTG */
 	disable-over-current;
 	external-vbus-divider;
 	maximum-speed = "full-speed";
+	tpl-support;
 };
diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt
index 467ddd15d40c..482f815363ef 100644
--- a/Documentation/devicetree/bindings/usb/dwc2.txt
+++ b/Documentation/devicetree/bindings/usb/dwc2.txt
@@ -4,6 +4,9 @@ Platform DesignWare HS OTG USB 2.0 controller
 Required properties:
 - compatible : One of:
   - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC.
+  - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc;
+  - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc;
+  - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc;
   - snps,dwc2: A generic DWC2 USB controller with default parameters.
 - reg : Should contain 1 register range (address and length)
 - interrupts : Should contain 1 interrupt
@@ -15,6 +18,8 @@ Optional properties:
 - phys: phy provider specifier
 - phy-names: shall be "usb2-phy"
 Refer to phy/phy-bindings.txt for generic phy consumer properties
+- dr_mode: shall be one of "host", "peripheral" and "otg"
+  Refer to usb/generic.txt
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt
new file mode 100644
index 000000000000..f9d70252bbb2
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt
@@ -0,0 +1,68 @@
+ST DWC3 glue logic
+
+This file documents the parameters for the dwc3-st driver.
+This driver controls the glue logic used to configure the dwc3 core on
+STiH407 based platforms.
+
+Required properties:
+ - compatible	: must be "st,stih407-dwc3"
+ - reg		: glue logic base address and USB syscfg ctrl register offset
+ - reg-names	: should be "reg-glue" and "syscfg-reg"
+ - st,syscon	: should be phandle to system configuration node which
+		  encompasses the glue registers
+ - resets	: list of phandle and reset specifier pairs. There should be two entries, one
+		  for the powerdown and softreset lines of the usb3 IP
+ - reset-names	: list of reset signal names. Names should be "powerdown" and "softreset"
+See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
+See: Documentation/devicetree/bindings/reset/reset.txt
+
+ - #address-cells, #size-cells : should be '1' if the device has sub-nodes
+   with 'reg' property
+
+ - pinctl-names	: A pinctrl state named "default" must be defined
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+
+ - pinctrl-0	: Pin control group
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+
+ - ranges	: allows valid 1:1 translation between child's address space and
+		  parent's address space
+
+Sub-nodes:
+The dwc3 core should be added as subnode to ST DWC3 glue as shown in the
+example below. The DT binding details of dwc3 can be found in:
+Documentation/devicetree/bindings/usb/dwc3.txt
+
+NB: The dr_mode property described in [1] is NOT optional for this driver, as the default value
+is "otg", which isn't supported by this SoC. Valid dr_mode values for dwc3-st are either "host"
+or "device".
+
+[1] Documentation/devicetree/bindings/usb/generic.txt
+
+Example:
+
+st_dwc3: dwc3@8f94000 {
+	status		= "disabled";
+	compatible	= "st,stih407-dwc3";
+	reg		= <0x08f94000 0x1000>, <0x110 0x4>;
+	reg-names	= "reg-glue", "syscfg-reg";
+	st,syscfg	= <&syscfg_core>;
+	resets		= <&powerdown STIH407_USB3_POWERDOWN>,
+			  <&softreset STIH407_MIPHY2_SOFTRESET>;
+	reset-names	= "powerdown",
+			  "softreset";
+	#address-cells	= <1>;
+	#size-cells	= <1>;
+	pinctrl-names	= "default";
+	pinctrl-0	= <&pinctrl_usb3>;
+	ranges;
+
+	dwc3: dwc3@9900000 {
+		compatible	= "snps,dwc3";
+		reg		= <0x09900000 0x100000>;
+		interrupts	= <GIC_SPI 155 IRQ_TYPE_NONE>;
+		dr_mode		= "host";
+		phys-names      = "usb2-phy", "usb3-phy";
+		phys            = <&usb2_picophy2>, <&phy_port2 MIPHY_TYPE_USB>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/usb/ehci-st.txt b/Documentation/devicetree/bindings/usb/ehci-st.txt
new file mode 100644
index 000000000000..fb45fa5770bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/ehci-st.txt
@@ -0,0 +1,39 @@
+ST USB EHCI controller
+
+Required properties:
+ - compatible		: must be "st,st-ehci-300x"
+ - reg			: physical base addresses of the controller and length of memory mapped
+			  region
+ - interrupts		: one EHCI interrupt should be described here
+ - pinctrl-names	: a pinctrl state named "default" must be defined
+ - pinctrl-0		: phandle referencing pin configuration of the USB controller
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+ - clocks		: phandle list of usb clocks
+ - clock-names		: should be "ic" for interconnect clock and "clk48"
+See: Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+ - phys			: phandle for the PHY device
+ - phy-names		: should be "usb"
+ - resets		: phandle + reset specifier pairs to the powerdown and softreset lines
+			  of the USB IP
+ - reset-names		: should be "power" and "softreset"
+See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
+See: Documentation/devicetree/bindings/reset/reset.txt
+
+Example:
+
+	ehci1: usb@0xfe203e00 {
+		compatible = "st,st-ehci-300x";
+		reg = <0xfe203e00 0x100>;
+		interrupts = <GIC_SPI 148 IRQ_TYPE_NONE>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb1>;
+		clocks = <&clk_s_a1_ls 0>;
+		phys = <&usb2_phy>;
+		phy-names = "usb";
+		status = "okay";
+
+		resets = <&powerdown STIH416_USB1_POWERDOWN>,
+			 <&softreset STIH416_USB1_SOFTRESET>;
+		reset-names = "power", "softreset";
+	};
diff --git a/Documentation/devicetree/bindings/usb/mxs-phy.txt b/Documentation/devicetree/bindings/usb/mxs-phy.txt
index 96681c93b86d..379b84a567cc 100644
--- a/Documentation/devicetree/bindings/usb/mxs-phy.txt
+++ b/Documentation/devicetree/bindings/usb/mxs-phy.txt
@@ -5,6 +5,7 @@ Required properties:
 	* "fsl,imx23-usbphy" for imx23 and imx28
 	* "fsl,imx6q-usbphy" for imx6dq and imx6dl
 	* "fsl,imx6sl-usbphy" for imx6sl
+	* "fsl,vf610-usbphy" for Vybrid vf610
 	* "fsl,imx6sx-usbphy" for imx6sx
   "fsl,imx23-usbphy" is still a fallback for other strings
 - reg: Should contain registers location and length
diff --git a/Documentation/devicetree/bindings/usb/ohci-st.txt b/Documentation/devicetree/bindings/usb/ohci-st.txt
new file mode 100644
index 000000000000..6d8393748da2
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/ohci-st.txt
@@ -0,0 +1,37 @@
+ST USB OHCI controller
+
+Required properties:
+
+ - compatible		: must be "st,st-ohci-300x"
+ - reg			: physical base addresses of the controller and length of memory mapped
+			  region
+ - interrupts		: one OHCI controller interrupt should be described here
+ - clocks		: phandle list of usb clocks
+ - clock-names		: should be "ic" for interconnect clock and "clk48"
+See: Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+ - phys			: phandle for the PHY device
+ - phy-names		: should be "usb"
+
+ - resets		: phandle to the powerdown and reset controller for the USB IP
+ - reset-names		: should be "power" and "softreset".
+See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
+See: Documentation/devicetree/bindings/reset/reset.txt
+
+Example:
+
+	ohci0: usb@0xfe1ffc00 {
+		compatible = "st,st-ohci-300x";
+		reg = <0xfe1ffc00 0x100>;
+		interrupts = <GIC_SPI 149 IRQ_TYPE_NONE>;
+		clocks = <&clk_s_a1_ls 0>,
+			 <&clockgen_b0 0>;
+		clock-names = "ic", "clk48";
+		phys = <&usb2_phy>;
+		phy-names = "usb";
+		status = "okay";
+
+		resets = <&powerdown STIH416_USB0_POWERDOWN>,
+			 <&softreset STIH416_USB0_SOFTRESET>;
+		reset-names = "power", "softreset";
+	};
diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
new file mode 100644
index 000000000000..ca164e71dd50
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
@@ -0,0 +1,66 @@
+Qualcomm SuperSpeed DWC3 USB SoC controller
+
+Required properties:
+- compatible:	should contain "qcom,dwc3"
+- clocks:		A list of phandle + clock-specifier pairs for the
+				clocks listed in clock-names
+- clock-names:	Should contain the following:
+  "core"		Master/Core clock, have to be >= 125 MHz for SS
+				operation and >= 60MHz for HS operation
+
+Optional clocks:
+  "iface"		System bus AXI clock.  Not present on all platforms
+  "sleep"		Sleep clock, used when USB3 core goes into low
+				power mode (U3).
+
+Required child node:
+A child node must exist to represent the core DWC3 IP block. The name of
+the node is not important. The content of the node is defined in dwc3.txt.
+
+Phy documentation is provided in the following places:
+Documentation/devicetree/bindings/phy/qcom,dwc3-usb-phy.txt
+
+Example device nodes:
+
+		hs_phy: phy@100f8800 {
+			compatible = "qcom,dwc3-hs-usb-phy";
+			reg = <0x100f8800 0x30>;
+			clocks = <&gcc USB30_0_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "ok";
+		};
+
+		ss_phy: phy@100f8830 {
+			compatible = "qcom,dwc3-ss-usb-phy";
+			reg = <0x100f8830 0x30>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "ok";
+		};
+
+		usb3_0: usb30@0 {
+			compatible = "qcom,dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			status = "ok";
+
+			dwc3@10000000 {
+				compatible = "snps,dwc3";
+				reg = <0x10000000 0xcd00>;
+				interrupts = <0 205 0x4>;
+				phys = <&hs_phy>, <&ss_phy>;
+				phy-names = "usb2-phy", "usb3-phy";
+				tx-fifo-resize;
+				dr_mode = "host";
+			};
+		};
+
diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
new file mode 100644
index 000000000000..b08c903f8668
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
@@ -0,0 +1,24 @@
+Renesas Electronics USBHS driver
+
+Required properties:
+  - compatible: Must contain one of the following:
+	- "renesas,usbhs-r8a7790"
+	- "renesas,usbhs-r8a7791"
+  - reg: Base address and length of the register for the USBHS
+  - interrupts: Interrupt specifier for the USBHS
+  - clocks: A list of phandle + clock specifier pairs
+
+Optional properties:
+  - renesas,buswait: Integer to use BUSWAIT register
+  - renesas,enable-gpio: A gpio specifier to check GPIO determining if USB
+			 function should be enabled
+  - phys: phandle + phy specifier pair
+  - phy-names: must be "usb"
+
+Example:
+	usbhs: usb@e6590000 {
+		compatible = "renesas,usbhs-r8a7790";
+		reg = <0 0xe6590000 0 0x100>;
+		interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
+	};
diff --git a/Documentation/devicetree/bindings/usb/udc-xilinx.txt b/Documentation/devicetree/bindings/usb/udc-xilinx.txt
new file mode 100644
index 000000000000..47b4e397a08d
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/udc-xilinx.txt
@@ -0,0 +1,18 @@
+Xilinx USB2 device controller
+
+Required properties:
+- compatible		: Should be "xlnx,usb2-device-4.00.a"
+- reg			: Physical base address and size of the USB2
+			  device registers map.
+- interrupts		: Should contain single irq line of USB2 device
+			  controller
+- xlnx,has-builtin-dma	: if DMA is included
+
+Example:
+ 		axi-usb2-device@42e00000 {
+                        compatible = "xlnx,usb2-device-4.00.a";
+                        interrupts = <0x0 0x39 0x1>;
+                        reg = <0x42e00000 0x10000>;
+                        xlnx,has-builtin-dma;
+                };
+
diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt
index 221ac0dbc678..52493b1480e2 100644
--- a/Documentation/devicetree/bindings/usb/usb3503.txt
+++ b/Documentation/devicetree/bindings/usb/usb3503.txt
@@ -8,8 +8,8 @@ Optional properties:
        if I2C is used.
 - connect-gpios: Should specify GPIO for connect.
 - disabled-ports: Should specify the ports unused.
-	'1' or '2' or '3' are availe for this property to describe the port
-	number. 1~3 property values are possible to be desribed.
+	'1' or '2' or '3' are available for this property to describe the port
+	number. 1~3 property values are possible to be described.
 	Do not describe this property if all ports have to be enabled.
 - intn-gpios: Should specify GPIO for interrupt.
 - reset-gpios: Should specify GPIO for reset.
diff --git a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt
index 97ce94e1a6cc..c101a4b17131 100644
--- a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt
+++ b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt
@@ -4,6 +4,7 @@ Required properties:
 - #index-cells: Cells used to descibe usb controller index. Should be <1>
 - compatible: Should be one of below:
 	"fsl,imx6q-usbmisc" for imx6q
+	"fsl,vf610-usbmisc" for Vybrid vf610
 - reg: Should contain registers location and length
 
 Examples:
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 252e4e4c122a..e1e34ad80600 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -29,6 +29,7 @@ calxeda	Calxeda
 capella	Capella Microsystems, Inc
 cavium	Cavium, Inc.
 cdns	Cadence Design Systems Inc.
+chipidea	Chipidea, Inc
 chrp	Common Hardware Reference Platform
 chunghwa	Chunghwa Picture Tubes Ltd.
 cirrus	Cirrus Logic, Inc.