summaryrefslogtreecommitdiff
path: root/Documentation/hwmon/ltc4261
diff options
context:
space:
mode:
authorMauro Carvalho Chehab <mchehab+samsung@kernel.org>2019-04-17 06:46:29 -0300
committerGuenter Roeck <linux@roeck-us.net>2019-04-17 10:37:23 -0700
commit7ebd8b66dd9e5a0b65e5ee5e2b8e7ca382ec97b7 (patch)
tree9db30159bd32bec125c7d49e80a79bb7c4da0c8e /Documentation/hwmon/ltc4261
parentb04f2f7d387b3160883c2a1f5e2285483a791e82 (diff)
docs: hwmon: Add an index file and rename docs to *.rst
Now that all files were converted to ReST format, rename them and add an index. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Diffstat (limited to 'Documentation/hwmon/ltc4261')
-rw-r--r--Documentation/hwmon/ltc426171
1 files changed, 0 insertions, 71 deletions
diff --git a/Documentation/hwmon/ltc4261 b/Documentation/hwmon/ltc4261
deleted file mode 100644
index c80233f8082e..000000000000
--- a/Documentation/hwmon/ltc4261
+++ /dev/null
@@ -1,71 +0,0 @@
-Kernel driver ltc4261
-=====================
-
-Supported chips:
-
- * Linear Technology LTC4261
-
- Prefix: 'ltc4261'
-
- Addresses scanned: -
-
- Datasheet:
-
- http://cds.linear.com/docs/Datasheet/42612fb.pdf
-
-Author: Guenter Roeck <linux@roeck-us.net>
-
-
-Description
------------
-
-The LTC4261/LTC4261-2 negative voltage Hot Swap controllers allow a board
-to be safely inserted and removed from a live backplane.
-
-
-Usage Notes
------------
-
-This driver does not probe for LTC4261 devices, since there is no register
-which can be safely used to identify the chip. You will have to instantiate
-the devices explicitly.
-
-Example: the following will load the driver for an LTC4261 at address 0x10
-on I2C bus #1::
-
- $ modprobe ltc4261
- $ echo ltc4261 0x10 > /sys/bus/i2c/devices/i2c-1/new_device
-
-
-Sysfs entries
--------------
-
-Voltage readings provided by this driver are reported as obtained from the ADC
-registers. If a set of voltage divider resistors is installed, calculate the
-real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the
-value of the divider resistor against the measured voltage and R2 is the value
-of the divider resistor against Ground.
-
-Current reading provided by this driver is reported as obtained from the ADC
-Current Sense register. The reported value assumes that a 1 mOhm sense resistor
-is installed. If a different sense resistor is installed, calculate the real
-current by dividing the reported value by the sense resistor value in mOhm.
-
-The chip has two voltage sensors, but only one set of voltage alarm status bits.
-In many many designs, those alarms are associated with the ADIN2 sensor, due to
-the proximity of the ADIN2 pin to the OV pin. ADIN2 is, however, not available
-on all chip variants. To ensure that the alarm condition is reported to the user,
-report it with both voltage sensors.
-
-======================= =============================
-in1_input ADIN2 voltage (mV)
-in1_min_alarm ADIN/ADIN2 Undervoltage alarm
-in1_max_alarm ADIN/ADIN2 Overvoltage alarm
-
-in2_input ADIN voltage (mV)
-in2_min_alarm ADIN/ADIN2 Undervoltage alarm
-in2_max_alarm ADIN/ADIN2 Overvoltage alarm
-
-curr1_input SENSE current (mA)
-curr1_alarm SENSE overcurrent alarm
-======================= =============================