Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM/arm64 Devicetree updates from Olof Johansson:
 "As usual, device tree updates is the bulk of our material in this
  merge window. This time around, 559 patches affecting both 32- and
  64-bit platforms.

  Changes are too many to list individually, but some of the larger
  ones:

  New platform/SoC support:

   - Automotive:
     + Renesas R-Car D3 (R8A77995)
     + TI DT76x
     + MediaTek mt2712e
   - Communication-oriented:
     + Qualcomm IPQ8074
     + Broadcom Stingray
     + Marvell Armada 8080
   - Set top box:
     + Uniphier PXs3

  Besides some vendor reference boards for the SoC above, there are also
  several new boards/machines:

   - TI AM335x Moxa UC-8100-ME-T open platform
   - TI AM57xx Beaglebone X15 Rev C
   - Microchip/Atmel sama5d27 SoM1 EK
   - Broadcom Raspberry Pi Zero W
   - Gemini-based D-Link DIR-685 router
   - Freescale i.MX6:
     + Toradex Apalis module + Apalis and Ixora carrier boards
     + Engicam GEAM6UL Starter Kit
   - Freescale i.MX53-based Beckhoff CX9020 Embedded PC
   - Mediatek mt7623-based BananaPi R2
   - Several Allwinner-based single-board computers:
  + Cubietruck plus
  + Bananapi M3, M2M and M64
  + NanoPi A64
  + A64-OLinuXino
  + Pine64
   - Rockchip RK3328 Pine64/Rock64 board support
   - Rockchip RK3399 boards:
  + RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
  + Theobroma Systems RK3399-Q7 SoM
   - ZTE ZX296718 PCBOX Board"

* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
  ARM: dts: at91: at91sam9g45: add AC97
  arm64: dts: marvell: mcbin: enable more networking ports
  arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
  arm64: dts: marvell: add TX interrupts for PPv2.2
  arm64: dts: uniphier: add PXs3 SoC support
  ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
  ARM: dts: uniphier: fix size of sdctrl nodes
  ARM: dts: uniphier: add AIDET nodes
  arm64: dts: uniphier: fix size of sdctrl node
  arm64: dts: uniphier: add AIDET nodes
  Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
  arm64: dts: uniphier: add reset controller node of analog amplifier
  arm64: dts: marvell: add Device Tree files for Armada-8KP
  arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
  arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
  dt-bindings: add rk3399-q7 SoM
  ARM: dts: rockchip: enable usb for rv1108-evb
  ARM: dts: rockchip: add usb nodes for rv1108 SoCs
  dt-bindings: update grf-binding for rv1108 SoCs
  ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
  ...

1 files changed, 51 insertions, 1 deletions

diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
index c72a27d908b6..20725ca487f3 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
@@ -1 +1,51 @@
-#include "arm64/broadcom/bcm2837-rpi-3-b.dts"
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model B";
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	leds {
+		act {
+			gpios = <&gpio 47 0>;
+		};
+	};
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
+	status = "okay";
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	status = "okay";
+	bus-width = <4>;
+	non-removable;
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
+	bus-width = <4>;
+};