ARM: dts: Move .dts files to vendor sub-directories

The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.

There's no change to dtbs_install as the flat structure is maintained on
install.

The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
  been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
  company (e.g. gemini, nspire)

The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>

1 files changed, 790 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts b/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts
new file mode 100644
index 000000000000..999adeca6f33
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts
@@ -0,0 +1,790 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama5d2_icp.dts - Device Tree file for SAMA5D2-ICP board
+ *
+ *  Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
+ *
+ *	Author: Radu Pirea & Razvan Stefanescu,
+ *		Codrin Ciubotariu <codrin.ciubotariu@microchip.com>,
+ *		Cristian Birsan <cristian.birsan@microchip.com>
+ */
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+
+/ {
+	model = "Microchip SAMA5D2-ICP";
+	compatible = "microchip,sama5d2-icp", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
+
+	aliases {
+		serial0 = &uart0;	/* debug uart0 + mikro BUS 1 */
+		serial1 = &uart1;	/* mikro BUS 3 */
+		serial3 = &uart3;	/* mikro BUS 2 */
+		serial5 = &uart7;	/* flx2 */
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button-1 {
+			label = "USER_PB1";
+			gpios = <&pioA PIN_PD0 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led_gpio_default>;
+		status = "okay"; /* conflict with pwm0 */
+
+		led-red {
+			label = "red";
+			gpios = <&pioA PIN_PB0 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-green {
+			label = "green";
+			gpios = <&pioA PIN_PB1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-blue {
+			label = "blue";
+			gpios = <&pioA PIN_PA31 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&adc {
+	vddana-supply = <&vdd_io_reg>;
+	vref-supply = <&vdd_io_reg>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_default>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
+	status = "okay";
+};
+
+&flx0 { /* mikrobus2 spi */
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+
+	spi2: spi@400 {
+		dmas = <0>, <0>;
+		cs-gpios = <&pioA PIN_PC0 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mikrobus2_spi &pinctrl_ksz_spi_cs>;
+		status = "okay";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch0: ksz8563@0 {
+			compatible = "microchip,ksz8563";
+			reg = <0>;
+			reset-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_LOW>;
+
+			spi-max-frequency = <500000>;
+			spi-cpha;
+			spi-cpol;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					label = "lan1";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan2";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "cpu";
+					ethernet = <&macb0>;
+					phy-mode = "mii";
+					fixed-link {
+						speed = <100>;
+						full-duplex;
+					};
+				};
+			};
+		};
+	};
+};
+
+&flx2 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart7: serial@200 {
+		pinctrl-0 = <&pinctrl_flx2_default>;
+		pinctrl-names = "default";
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		status = "okay"; /* Conflict w/ qspi1. */
+	};
+};
+
+&flx3 { /* mikrobus1 spi */
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+
+	spi5: spi@400 {
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mikrobus1_spi &pinctrl_mikrobus1_spi_cs>;
+		status = "okay";
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c6: i2c@600 {
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx4_default>;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "okay";
+
+		mcp16502@5b {
+			compatible = "microchip,mcp16502";
+			reg = <0x5b>;
+			status = "okay";
+			lpm-gpios = <&pioBU 7 GPIO_ACTIVE_LOW>;
+
+			regulators {
+				vdd_io_reg: VDD_IO {
+					regulator-name = "VDD_IO";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				VDD_DDR {
+					regulator-name = "VDD_DDR";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-on-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				VDD_CORE {
+					regulator-name = "VDD_CORE";
+					regulator-min-microvolt = <1250000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				VDD_OTHER {
+					regulator-name = "VDD_OTHER";
+					regulator-min-microvolt = <600000>;
+					regulator-max-microvolt = <1850000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				LDO1 {
+					regulator-name = "LDO1";
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <2500000>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				LDO2 {
+					regulator-name = "LDO2";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+			};
+		};
+	};
+};
+
+&i2c0 { /* mikrobus i2c */
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_mikrobus_i2c>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	status = "okay";
+};
+
+&i2c1 {
+	dmas = <0>, <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	sda-gpios = <&pioA PIN_PD19 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+		status = "okay";
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+		status = "disabled";
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+		status = "disabled";
+	};
+};
+
+&macb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq &pinctrl_macb0_rst>;
+	phy-mode = "mii";
+	status = "okay";
+
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+};
+
+&pioA {
+	pinctrl_adc_default: adc_default {
+		pinmux = <PIN_PD24__GPIO>,
+				<PIN_PD25__GPIO>,
+				<PIN_PD26__GPIO>;
+		bias-disable;
+	};
+
+	/*
+	 * The ADTRG pin can work on any edge type.
+	 * In here it's being pulled up, so need to
+	 * connect it to ground to get an edge e.g.
+	 * Trigger can be configured on falling, rise
+	 * or any edge, and the pull-up can be changed
+	 * to pull-down or left floating according to
+	 * needs.
+	 */
+	pinctrl_adtrg_default: adtrg_default {
+		pinmux = <PIN_PD31__ADTRG>;
+		bias-pull-up;
+	};
+
+	pinctrl_flx4_default: flx4_default {
+		pinmux = <PIN_PC28__FLEXCOM4_IO0>,
+			 <PIN_PC29__FLEXCOM4_IO1>;
+		bias-disable;
+	};
+
+	pinctrl_can0_default: can0_default {
+		pinmux = <PIN_PC10__CANTX0>,
+			 <PIN_PC11__CANRX0>;
+		bias-disable;
+	};
+
+	pinctrl_can1_default: can1_default {
+		pinmux = <PIN_PC26__CANTX1>,
+			 <PIN_PC27__CANRX1>;
+		bias-disable;
+	};
+
+	pinctrl_i2c1_default: i2c1_default {
+		pinmux = <PIN_PD19__TWD1>,
+			 <PIN_PD20__TWCK1>;
+		bias-disable;
+	};
+
+	pinctrl_i2c1_gpio: i2c1_gpio {
+                pinmux = <PIN_PD19__GPIO>,
+                         <PIN_PD20__GPIO>;
+                bias-disable;
+        };
+
+	pinctrl_key_gpio_default: key_gpio_default {
+		pinmux = <PIN_PD0__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_led_gpio_default: led_gpio_default {
+		pinmux = <PIN_PB0__GPIO>,
+			 <PIN_PB1__GPIO>,
+			 <PIN_PA31__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_qspi1_default: qspi1_default {
+		pinmux = <PIN_PA6__QSPI1_SCK>,
+			 <PIN_PA7__QSPI1_IO0>,
+			 <PIN_PA8__QSPI1_IO1>,
+			 <PIN_PA9__QSPI1_IO2>,
+			 <PIN_PA10__QSPI1_IO3>,
+			 <PIN_PA11__QSPI1_CS>;
+		bias-disable;
+	};
+
+	pinctrl_sdmmc0_default: sdmmc0_default {
+		cmd_data {
+			pinmux = <PIN_PA1__SDMMC0_CMD>,
+				 <PIN_PA2__SDMMC0_DAT0>,
+				 <PIN_PA3__SDMMC0_DAT1>,
+				 <PIN_PA4__SDMMC0_DAT2>,
+				 <PIN_PA5__SDMMC0_DAT3>;
+			bias-disable;
+		};
+
+		ck_cd {
+			pinmux = <PIN_PA0__SDMMC0_CK>,
+				 <PIN_PA13__SDMMC0_CD>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdmmc1_default: sdmmc1_default {
+		cmd_data {
+			pinmux = <PIN_PA18__SDMMC1_DAT0>,
+				 <PIN_PA19__SDMMC1_DAT1>,
+				 <PIN_PA20__SDMMC1_DAT2>,
+				 <PIN_PA21__SDMMC1_DAT3>;
+			bias-disable;
+		};
+
+		ck_cd {
+			pinmux = <PIN_PA22__SDMMC1_CK>,
+				 <PIN_PA28__SDMMC1_CMD>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_mikrobus_i2c: mikrobus_i2c {
+		pinmux = <PIN_PD22__TWCK0>,
+			 <PIN_PD21__TWD0>;
+		bias-disable;
+	};
+
+	pinctrl_i2c0_gpio: i2c0_gpio {
+		pinmux = <PIN_PD21__GPIO>,
+			 <PIN_PD22__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_an: mikrobus1_an {
+		pinmux = <PIN_PD26__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_rst: mikrobus1_rst {
+		pinmux = <PIN_PC5__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_spi_cs: mikrobus1_spi_cs {
+		pinmux = <PIN_PC21__FLEXCOM3_IO3>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_spi: mikrobus1_spi {
+		pinmux = <PIN_PC20__FLEXCOM3_IO0>,
+			 <PIN_PC19__FLEXCOM3_IO1>,
+			 <PIN_PC18__FLEXCOM3_IO2>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_pwm: mikrobus1_pwm {
+		pinmux = <PIN_PC4__TIOB1>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_int: mikrobus1_int {
+		pinmux = <PIN_PC3__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_uart: mikrobus1_uart {
+		pinmux = <PIN_PB26__URXD0>,
+			 <PIN_PB27__UTXD0>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_an: mikrobus2_an {
+		pinmux = <PIN_PD25__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_rst: mikrobus2_rst {
+		pinmux = <PIN_PB24__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_spi_cs: mikrobus2_spi_cs {
+		pinmux = <PIN_PB31__FLEXCOM0_IO3>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_spi: mikrobus2_spi {
+		pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+			 <PIN_PB29__FLEXCOM0_IO1>,
+			 <PIN_PB30__FLEXCOM0_IO2>;
+		bias-disable;
+	};
+
+	pinctrl_ksz_spi_cs: ksz_spi_cs {
+		pinmux = <PIN_PC0__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_pwm: mikrobus2_pwm {
+		pinmux = <PIN_PB23__TIOB2>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_int: mikrobus2_int {
+		pinmux = <PIN_PB22__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_uart: mikrobus2_uart {
+		pinmux = <PIN_PC12__URXD3>,
+			 <PIN_PC13__UTXD3>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_an: mikrobus3_an {
+		pinmux = <PIN_PD24__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_rst: mikrobus3_rst {
+		pinmux = <PIN_PB21__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_spi_cs: mikrobus3_spi_cs {
+		pinmux = <PIN_PA17__SPI0_NPCS0>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_spi: mikrobus3_spi {
+		pinmux = <PIN_PA14__SPI0_SPCK>,
+			 <PIN_PA16__SPI0_MISO>,
+			 <PIN_PA15__SPI0_MOSI>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_pwm: mikrobus3_pwm {
+		pinmux = <PIN_PB20__TIOB3>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_int: mikrobus3_int {
+		pinmux = <PIN_PB18__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_uart: mikrobus3_uart {
+		pinmux = <PIN_PC7__URXD1>,
+			 <PIN_PC8__UTXD1>;
+		bias-disable;
+	};
+
+	pinctrl_usb_default: usb_default {
+		pinmux = <PIN_PC17__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_usba_vbus: usba_vbus {
+		pinmux = <PIN_PD23__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_pwm0_pwm2_default: pwm0_pwm2_default {
+		pinmux = <PIN_PB5__PWMH2>,
+			 <PIN_PB6__PWML2>;
+		bias-pull-up;
+	};
+
+	pinctrl_macb0_default: macb0_default {
+		pinmux = <PIN_PD1__GRXCK>,
+			 <PIN_PD2__GTXER>,
+			 <PIN_PD5__GRX2>,
+			 <PIN_PD6__GRX3>,
+			 <PIN_PD7__GTX2>,
+			 <PIN_PD8__GTX3>,
+			 <PIN_PD9__GTXCK>,
+			 <PIN_PD10__GTXEN>,
+			 <PIN_PD11__GRXDV>,
+			 <PIN_PD12__GRXER>,
+			 <PIN_PD13__GRX0>,
+			 <PIN_PD14__GRX1>,
+			 <PIN_PD15__GTX0>,
+			 <PIN_PD16__GTX1>,
+			 <PIN_PD17__GMDC>,
+			 <PIN_PD18__GMDIO>;
+		bias-disable;
+	};
+
+	pinctrl_macb0_phy_irq: macb0_phy_irq {
+		pinmux = <PIN_PD3__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_macb0_rst: macb0_sw_rst {
+		pinmux = <PIN_PD4__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_flx2_default: flx2_default {
+		pinmux = <PIN_PA6__FLEXCOM2_IO0>,
+			 <PIN_PA7__FLEXCOM2_IO1>,
+			 <PIN_PA9__FLEXCOM2_IO3>,
+			 <PIN_PA10__FLEXCOM2_IO4>;
+		bias-disable;
+	};
+};
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_pwm2_default>;
+	status = "disabled"; /* conflict with leds, HSIC */
+};
+
+&qspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi1_default>;
+	status = "disabled"; /* Conflict with wilc_pwrseq, flx2 */
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <104000000>;
+		spi-cs-setup-ns = <7>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		m25p,fast-read;
+
+		at91bootstrap@0 {
+			label = "qspi: at91bootstrap";
+			reg = <0x00000000 0x00040000>;
+		};
+
+		bootloader@40000 {
+			label = "qspi: bootloader";
+			reg = <0x00040000 0x000c0000>;
+		};
+
+		bootloaderenvred@100000 {
+			label = "qspi: bootloader env redundant";
+			reg = <0x00100000 0x00040000>;
+		};
+
+		bootloaderenv@140000 {
+			label = "qspi: bootloader env";
+			reg = <0x00140000 0x00040000>;
+		};
+
+		dtb@180000 {
+			label = "qspi: device tree";
+			reg = <0x00180000 0x00080000>;
+		};
+
+		kernel@200000 {
+			label = "qspi: kernel";
+			reg = <0x00200000 0x00600000>;
+		};
+	};
+};
+
+&sdmmc0 {
+	no-1-8-v;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default>;
+	status = "okay";
+};
+
+&shutdown_controller {
+	debounce-delay-us = <976>;
+	atmel,wakeup-rtc-timer;
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&spi0 {  /* mikrobus3 spi */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus3_spi &pinctrl_mikrobus3_spi_cs>;
+	status = "okay";
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus1_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus3_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus2_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&usb0 {
+	atmel,vbus-gpio = <&pioA PIN_PD23 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	num-ports = <3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_default>;
+	status = "okay";
+};
+
+&usb2 {
+	phy_type = "hsic";
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};