Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...

1 files changed, 357 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-zii-rmu2.dts b/arch/arm/boot/dts/nxp/imx/imx7d-zii-rmu2.dts
new file mode 100644
index 000000000000..521493342fe9
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-zii-rmu2.dts
@@ -0,0 +1,357 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device tree file for ZII's RMU2 board
+ *
+ * RMU - Remote Modem Unit
+ *
+ * Copyright (C) 2019 Zodiac Inflight Innovations
+ */
+
+/dts-v1/;
+#include <dt-bindings/thermal/thermal.h>
+#include "imx7d.dtsi"
+
+/ {
+	model = "ZII RMU2 Board";
+	compatible = "zii,imx7d-rmu2", "fsl,imx7d";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pinctrl_leds_debug>;
+		pinctrl-names = "default";
+
+		led-debug {
+			label = "zii:green:debug1";
+			gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&sw1a_reg>;
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&fec1_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fec1_phy: ethernet-phy@0 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_enet1_phy_reset>,
+				    <&pinctrl_enet1_phy_interrupt>;
+			reg = <0>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pmic@8 {
+		compatible = "fsl,pfuze3000";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1a {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1b {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c04";
+		reg = <0x52>;
+	};
+};
+
+&snvs_rtc {
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	assigned-clocks = <&clks IMX7D_UART2_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	assigned-clocks = <&clks IMX7D_UART4_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
+	status = "okay";
+
+	mcu {
+		compatible = "zii,rave-sp-rdu2";
+		current-speed = <1000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		watchdog {
+			compatible = "zii,rave-sp-watchdog";
+		};
+
+		eeprom@a3 {
+			compatible = "zii,rave-sp-eeprom";
+			reg = <0xa3 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			zii,eeprom-name = "main-eeprom";
+		};
+	};
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	bus-width = <4>;
+	no-1-8-v;
+	no-sdio;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sdio;
+	no-sd;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX7D_PAD_ECSPI1_SCLK__ECSPI1_SCLK	0x2
+			MX7D_PAD_ECSPI1_MOSI__ECSPI1_MOSI	0x2
+			MX7D_PAD_ECSPI1_MISO__ECSPI1_MISO	0x2
+			MX7D_PAD_ECSPI1_SS0__GPIO4_IO19         0x59
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX7D_PAD_SD2_CD_B__ENET1_MDIO				0x3
+			MX7D_PAD_SD2_WP__ENET1_MDC				0x3
+			MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC		0x1
+			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0		0x1
+			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1		0x1
+			MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2		0x1
+			MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3		0x1
+			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL		0x1
+			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC		0x1
+			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0		0x1
+			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1		0x1
+			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2		0x1
+			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3		0x1
+			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL		0x1
+		>;
+	};
+
+	pinctrl_enet1_phy_reset: enet1phyresetgrp {
+		fsl,pins = <
+			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x14
+
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX7D_PAD_I2C1_SDA__I2C1_SDA		0x4000007f
+			MX7D_PAD_I2C1_SCL__I2C1_SCL		0x4000007f
+		>;
+	};
+
+	pinctrl_leds_debug: ledsgrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA08__GPIO2_IO8		0x59
+		>;
+	};
+
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX7D_PAD_UART2_RX_DATA__UART2_DCE_RX	0x79
+			MX7D_PAD_UART2_TX_DATA__UART2_DCE_TX	0x79
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX7D_PAD_SD2_DATA0__UART4_DCE_RX	0x79
+			MX7D_PAD_SD2_DATA1__UART4_DCE_TX	0x79
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x59
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x19
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x19
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x59
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x59
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x59
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x59
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x59
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x59
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x59
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x59
+			MX7D_PAD_SD3_RESET_B__SD3_RESET_B	0x59
+		>;
+	};
+};
+
+&iomuxc_lpsr {
+	pinctrl_enet1_phy_interrupt: enet1phyinterruptgrp {
+		fsl,phy = <
+			MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2	0x08
+		>;
+	};
+};