Merge tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull SoC DT updates from Arnd Bergmann:
 "About a quarter of the changes are for 32-bit arm, mostly filling in
  device support for existing machines and adding minor cleanups, mostly
  for Qualcomm and Samsung based machines.

  Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
  Rockchips that have been around for a while but were lacking kernel
  support so far: RV1126 is a Vision SoC with an NPU and is used in the
  Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
  for TV boxes and so far only comes with a dts for its refernece
  design.

  The other 32-bit boards that were added are two ASpeed AST2600 based
  BMC boards, the Microchip sam9x60_curiosity development board (Armv5
  based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
  for i.MX53 and i.MX6ULL.

  On the RISC-V side, there are fewer patches, but a total of ten new
  single-board computers based on variations of the Allwinner D1/T113
  chip, plus one more board based on Microchip Polarfire.

  As usual, arm64 has by far the most changes here, with over 700
  non-merge changesets, among them over 400 alone for Qualcomm. The
  newly added SoCs this time are all recent high-end embedded SoCs for
  various markets, each on comes with support for its reference board:

   - Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
   - Qualcomm QDU1000/QRU1000 5G RAN platform
   - Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
   - TI J784S4 for industrial and automotive applications

  In total, there are 46 new arm64 machines:
   - Reference platforms for each of the five new SoCs
   - Three Amlogic based development boards
   - Six embedded machines based on NXP i.MX8MM and i.MX8MP
   - The Mediatek mt7986a based Banana Pi R3 router
   - Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
     (Snapdragon 662) and SM8250 (Snapdragon 865)
   - Two LTE dongles, also based on MSM8916
   - Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
     SDM450 and SDM632
   - Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
   - Nine development boards based on Rockchips RK3588, RK3568, RK3566
     and RK3328.
   - Five development machines based on TI K3 (AM642/AM654/AM68/AM69)

  The cleanup of dtc warnings continues across all platforms, adding to
  the total number of changes"

* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
  dt-bindings: riscv: correct starfive visionfive 2 compatibles
  ARM: dts: socfpga: Add enclustra PE1 devicetree
  dt-bindings: altera: Add enclustra mercury PE1
  arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
  arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
  arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
  arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
  arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
  arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
  arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
  arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
  arm64: dts: qcom: pmk8350: Use the correct PON compatible
  arm64: dts: qcom: sc8280xp-x13s: Enable external display
  arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
  arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
  arm64: dts: qcom: sm8350-hdk: enable GPU
  arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
  arm64: dts: qcom: sm8350: finish reordering nodes
  arm64: dts: qcom: sm8350: move more nodes to correct place
  arm64: dts: qcom: sm8350: reorder device nodes
  ...

1 files changed, 622 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index 37a5d96aaf64..e67ede940071 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -170,6 +170,64 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf0000000 0x800>;
 				status = "disabled";
+
+				uart4: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi4: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c4: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx5: flexcom@f0004000 {
@@ -180,6 +238,65 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf0004000 0x800>;
 				status = "disabled";
+
+				uart5: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi5: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c5: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			dma0: dma-controller@f0008000 {
@@ -251,6 +368,45 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf0020000 0x800>;
 				status = "disabled";
+
+				uart11: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(22))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(23))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c11: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(22))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(23))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx12: flexcom@f0024000 {
@@ -261,6 +417,45 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf0024000 0x800>;
 				status = "disabled";
+
+				uart12: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(24))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(25))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c12: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(24))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(25))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			pit64b: timer@f0028000 {
@@ -379,6 +574,45 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf8010000 0x800>;
 				status = "disabled";
+
+				uart6: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(12))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(13))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c6: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(12))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(13))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx7: flexcom@f8014000 {
@@ -389,6 +623,45 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf8014000 0x800>;
 				status = "disabled";
+
+				uart7: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(14))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(15))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c7: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(14))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(15))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx8: flexcom@f8018000 {
@@ -399,6 +672,45 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf8018000 0x800>;
 				status = "disabled";
+
+				uart8: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(16))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c8: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(16))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx0: flexcom@f801c000 {
@@ -409,6 +721,64 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf801c000 0x800>;
 				status = "disabled";
+
+				uart0: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi0: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c0: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx1: flexcom@f8020000 {
@@ -419,6 +789,64 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf8020000 0x800>;
 				status = "disabled";
+
+				uart1: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi1: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c1: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx2: flexcom@f8024000 {
@@ -429,6 +857,64 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf8024000 0x800>;
 				status = "disabled";
+
+				uart2: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi2: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c2: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx3: flexcom@f8028000 {
@@ -439,6 +925,64 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf8028000 0x800>;
 				status = "disabled";
+
+				uart3: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi3: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c3: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			macb0: ethernet@f802c000 {
@@ -504,6 +1048,45 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf8040000 0x800>;
 				status = "disabled";
+
+				uart9: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(19))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c9: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(19))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx10: flexcom@f8044000 {
@@ -514,6 +1097,45 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf8044000 0x800>;
 				status = "disabled";
+
+				uart10: serial@200 {
+					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(20))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(21))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c10: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(20))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(21))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			isi: isi@f8048000 {