Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...

1 files changed, 593 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/ti/omap/dra72-evm-common.dtsi b/arch/arm/boot/dts/ti/omap/dra72-evm-common.dtsi
new file mode 100644
index 000000000000..31ab0c60ca75
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/dra72-evm-common.dtsi
@@ -0,0 +1,593 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - https://www.ti.com/
+ */
+/dts-v1/;
+
+#include "dra72x.dtsi"
+#include "dra7-ipu-dsp-common.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/ti-dra7-atl.h>
+
+/ {
+	compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
+
+	aliases {
+		display0 = &hdmi0;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	evm_12v0: fixedregulator-evm12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	evm_5v0: fixedregulator-evm5v0 {
+		/* Output 1 of TPS43351QDAPRQ1 on dra72-evm */
+		/* Output 1 of LM5140QRWGTQ1 on dra71-evm */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	evm_3v6: fixedregulator-evm_3v6 {
+		compatible = "regulator-fixed";
+		regulator-name = "evm_3v6";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+		vin-supply = <&evm_5v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_3v3: fixedregulator-vsys3v3 {
+		/* Output 2 of TPS43351QDAPRQ1 on dra72-evm */
+		/* Output 2 of LM5140QRWGTQ1 on dra71-evm */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	evm_3v3_sw: fixedregulator-evm_3v3 {
+		/* TPS22965DSG */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vsys_3v3>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	aic_dvdd: fixedregulator-aic_dvdd {
+		/* TPS77018DBVT */
+		compatible = "regulator-fixed";
+		regulator-name = "aic_dvdd";
+		vin-supply = <&evm_3v3_sw>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	evm_3v3_sd: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "evm_3v3_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&evm_3v3_sw>;
+		enable-active-high;
+		gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>;
+	};
+
+	extcon_usb1: extcon_usb1 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	extcon_usb2: extcon_usb2 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	hdmi0: connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&tpd12s015_out>;
+			};
+		};
+	};
+
+	tpd12s015: encoder {
+		compatible = "ti,tpd12s015";
+
+		gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>,	/* P4, CT CP HPD */
+			<&pcf_hdmi 5 GPIO_ACTIVE_HIGH>,	/* P5, LS OE */
+			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tpd12s015_in: endpoint {
+					remote-endpoint = <&hdmi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tpd12s015_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+
+	sound0: sound0 {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "DRA7xx-EVM";
+		simple-audio-card,widgets =
+			"Headphone", "Headphone Jack",
+			"Line", "Line Out",
+			"Microphone", "Mic Jack",
+			"Line", "Line In";
+		simple-audio-card,routing =
+			"Headphone Jack",       "HPLOUT",
+			"Headphone Jack",       "HPROUT",
+			"Line Out",		"LLOUT",
+			"Line Out",		"RLOUT",
+			"MIC3L",		"Mic Jack",
+			"MIC3R",		"Mic Jack",
+			"Mic Jack",		"Mic Bias",
+			"LINE1L",               "Line In",
+			"LINE1R",               "Line In";
+		simple-audio-card,format = "dsp_b";
+		simple-audio-card,bitclock-master = <&sound0_master>;
+		simple-audio-card,frame-master = <&sound0_master>;
+		simple-audio-card,bitclock-inversion;
+
+		sound0_master: simple-audio-card,cpu {
+			sound-dai = <&mcasp3>;
+			system-clock-frequency = <5644800>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&tlv320aic3106>;
+			clocks = <&atl_clkin2_ck>;
+		};
+	};
+
+	vmmcwl_fixed: fixedregulator-mmcwl {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcwl_fixed";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	clk_ov5640_fixed: clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+};
+
+&dra7_pmx_core {
+	dcan1_pins_default: dcan1-default-pins {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
+			DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1)	/* wakeup0.dcan1_rx */
+		>;
+	};
+
+	dcan1_pins_sleep: dcan1-sleep-pins {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
+			DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP)	/* wakeup0.off */
+		>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	pcf_lcd: gpio@20 {
+		compatible = "nxp,pcf8575";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	pcf_gpio_21: gpio@21 {
+		compatible = "nxp,pcf8575";
+		reg = <0x21>;
+		lines-initial-states = <0x1408>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	tlv320aic3106: tlv320aic3106@19 {
+		#sound-dai-cells = <0>;
+		compatible = "ti,tlv320aic3106";
+		reg = <0x19>;
+		adc-settle-ms = <40>;
+		ai3x-micbias-vg = <1>;		/* 2.0V */
+		status = "okay";
+
+		/* Regulators */
+		AVDD-supply = <&evm_3v3_sw>;
+		IOVDD-supply = <&evm_3v3_sw>;
+		DRVDD-supply = <&evm_3v3_sw>;
+		DVDD-supply = <&aic_dvdd>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	pcf_hdmi: pcf8575@26 {
+		compatible = "nxp,pcf8575";
+		reg = <0x26>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		/*
+		 * initial state is used here to keep the mdio interface
+		 * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and
+		 * VIN2_S0 driven high otherwise Ethernet stops working
+		 * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6
+		 */
+		lines-initial-states = <0x0f2b>;
+
+		hdmi-audio-hog {
+			/* vin6_sel_s0: high: VIN6, low: audio */
+			gpio-hog;
+			gpios = <1 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "vin6_sel_s0";
+		};
+	};
+
+	ov5640@3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+
+		clocks = <&clk_ov5640_fixed>;
+		clock-names = "xclk";
+
+		port {
+			csi2_cam0: endpoint {
+				remote-endpoint = <&csi2_phy0>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+
+};
+
+&uart1 {
+	status = "okay";
+	interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+			      <&dra7_pmx_core 0x3e0>;
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	/*
+	 * For the existing IOdelay configuration via U-Boot we don't
+	 * support NAND on dra72-evm. Keep it disabled. Enabling it
+	 * requires a different configuration by U-Boot.
+	 */
+	status = "disabled";
+	ranges = <0 0 0x08000000 0x01000000>;	/* minimum GPMC partition = 16MB */
+	nand@0,0 {
+		/* To use NAND, DIP switch SW5 must be set like so:
+		 * SW5.1 (NAND_SELn) = ON (LOW)
+		 * SW5.9 (GPMC_WPN) = OFF (HIGH)
+		 */
+		compatible = "ti,omap2-nand";
+		reg = <0 0 4>;		/* device IO registers */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
+		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
+		ti,nand-xfer-type = "prefetch-dma";
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <16>;
+		gpmc,device-width = <2>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <80>;
+		gpmc,cs-wr-off-ns = <80>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <60>;
+		gpmc,adv-wr-off-ns = <60>;
+		gpmc,we-on-ns = <10>;
+		gpmc,we-off-ns = <50>;
+		gpmc,oe-on-ns = <4>;
+		gpmc,oe-off-ns = <40>;
+		gpmc,access-ns = <40>;
+		gpmc,wr-access-ns = <80>;
+		gpmc,rd-cycle-ns = <80>;
+		gpmc,wr-cycle-ns = <80>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.SPL";
+			reg = <0x00000000 0x00020000>;
+		};
+		partition@1 {
+			label = "NAND.SPL.backup1";
+			reg = <0x00020000 0x00020000>;
+		};
+		partition@2 {
+			label = "NAND.SPL.backup2";
+			reg = <0x00040000 0x00020000>;
+		};
+		partition@3 {
+			label = "NAND.SPL.backup3";
+			reg = <0x00060000 0x00020000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot-spl-os";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@5 {
+			label = "NAND.u-boot";
+			reg = <0x000c0000 0x00100000>;
+		};
+		partition@6 {
+			label = "NAND.u-boot-env";
+			reg = <0x001c0000 0x00020000>;
+		};
+		partition@7 {
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x001e0000 0x00020000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00200000 0x00800000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00a00000 0x0f600000>;
+		};
+	};
+};
+
+&omap_dwc3_1 {
+	extcon = <&extcon_usb1>;
+};
+
+&omap_dwc3_2 {
+	extcon = <&extcon_usb2>;
+};
+
+&usb1 {
+	dr_mode = "otg";
+	extcon = <&extcon_usb1>;
+};
+
+&usb2 {
+	dr_mode = "host";
+	extcon = <&extcon_usb2>;
+};
+
+&mmc1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_default>;
+	vmmc-supply = <&evm_3v3_sd>;
+	bus-width = <4>;
+	/*
+	 * SDCD signal is not being used here - using the fact that GPIO mode
+	 * is a viable alternative
+	 */
+	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
+	max-frequency = <192000000>;
+};
+
+&mmc2 {
+	/* SW5-3 in ON position */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins_default>;
+	bus-width = <8>;
+	non-removable;
+	max-frequency = <192000000>;
+};
+
+&mmc4 {
+	status = "okay";
+	vmmc-supply = <&evm_3v6>;
+	vqmmc-supply = <&vmmcwl_fixed>;
+	bus-width = <4>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	non-removable;
+	pinctrl-names = "default", "hs", "sdr12", "sdr25";
+	pinctrl-0 = <&mmc4_pins_default>;
+	pinctrl-1 = <&mmc4_pins_default>;
+	pinctrl-2 = <&mmc4_pins_default>;
+	pinctrl-3 = <&mmc4_pins_default>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wifi@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <7 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+&dcan1 {
+	status = "okay";
+	pinctrl-names = "default", "sleep", "active";
+	pinctrl-0 = <&dcan1_pins_sleep>;
+	pinctrl-1 = <&dcan1_pins_sleep>;
+	pinctrl-2 = <&dcan1_pins_default>;
+};
+
+&qspi {
+	status = "okay";
+
+	spi-max-frequency = <76800000>;
+	flash@0 {
+		compatible = "s25fl256s1";
+		spi-max-frequency = <76800000>;
+		reg = <0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* MTD partition table.
+		 * The ROM checks the first four physical blocks
+		 * for a valid file to boot and the flash here is
+		 * 64KiB block size.
+		 */
+		partition@0 {
+			label = "QSPI.SPL";
+			reg = <0x00000000 0x00010000>;
+		};
+		partition@1 {
+			label = "QSPI.SPL.backup1";
+			reg = <0x00010000 0x00010000>;
+		};
+		partition@2 {
+			label = "QSPI.SPL.backup2";
+			reg = <0x00020000 0x00010000>;
+		};
+		partition@3 {
+			label = "QSPI.SPL.backup3";
+			reg = <0x00030000 0x00010000>;
+		};
+		partition@4 {
+			label = "QSPI.u-boot";
+			reg = <0x00040000 0x00100000>;
+		};
+		partition@5 {
+			label = "QSPI.u-boot-spl-os";
+			reg = <0x00140000 0x00080000>;
+		};
+		partition@6 {
+			label = "QSPI.u-boot-env";
+			reg = <0x001c0000 0x00010000>;
+		};
+		partition@7 {
+			label = "QSPI.u-boot-env.backup1";
+			reg = <0x001d0000 0x0010000>;
+		};
+		partition@8 {
+			label = "QSPI.kernel";
+			reg = <0x001e0000 0x0800000>;
+		};
+		partition@9 {
+			label = "QSPI.file-system";
+			reg = <0x009e0000 0x01620000>;
+		};
+	};
+};
+
+&dss {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+
+	port {
+		hdmi_out: endpoint {
+			remote-endpoint = <&tpd12s015_in>;
+		};
+	};
+};
+
+&atl {
+	assigned-clocks = <&abe_dpll_sys_clk_mux>,
+			  <&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>,
+			  <&dpll_abe_ck>,
+			  <&dpll_abe_m2x2_ck>,
+			  <&atl_clkin2_ck>;
+	assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>;
+	assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>;
+
+	status = "okay";
+
+	atl2 {
+		bws = <DRA7_ATL_WS_MCASP2_FSX>;
+		aws = <DRA7_ATL_WS_MCASP3_FSX>;
+	};
+};
+
+&mcasp3 {
+	#sound-dai-cells = <0>;
+
+	assigned-clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>;
+	assigned-clock-parents = <&atl_clkin2_ck>;
+
+	status = "okay";
+
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	/* 4 serializer */
+	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+		1 2 0 0
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};
+
+&pcie1_rc {
+	status = "okay";
+};
+
+&csi2_0 {
+	csi2_phy0: endpoint {
+		remote-endpoint = <&csi2_cam0>;
+		clock-lanes = <0>;
+		data-lanes = <1 2>;
+	};
+};