ARM: s3c: move into a common directory

s3c24xx and s3c64xx have a lot in common, but are split across three
separate directories, which makes the interaction of the header files
more complicated than necessary.

Move all three directories into a new mach-s3c, with a minimal
set of changes to each file.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[krzk: Rebase, add s3c24xx and s3c64xx suffix to several files, add SPDX
       headers to new files, remove plat-samsung from MAINTAINERS]
Co-developed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
https://lore.kernel.org/r/20200806182059.2431-39-krzk@kernel.org

13 files changed, 0 insertions, 1777 deletions

diff --git a/arch/arm/mach-s3c24xx/include/mach/dma.h b/arch/arm/mach-s3c24xx/include/mach/dma.h
deleted file mode 100644
index 25fc9c258fc1..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/dma.h
+++ /dev/null
@@ -1,51 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (C) 2003-2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Samsung S3C24XX DMA support
- */
-
-#ifndef __ASM_ARCH_DMA_H
-#define __ASM_ARCH_DMA_H __FILE__
-
-#include <linux/device.h>
-
-/* We use `virtual` dma channels to hide the fact we have only a limited
- * number of DMA channels, and not of all of them (dependent on the device)
- * can be attached to any DMA source. We therefore let the DMA core handle
- * the allocation of hardware channels to clients.
-*/
-
-enum dma_ch {
-	DMACH_XD0 = 0,
-	DMACH_XD1,
-	DMACH_SDI,
-	DMACH_SPI0,
-	DMACH_SPI1,
-	DMACH_UART0,
-	DMACH_UART1,
-	DMACH_UART2,
-	DMACH_TIMER,
-	DMACH_I2S_IN,
-	DMACH_I2S_OUT,
-	DMACH_PCM_IN,
-	DMACH_PCM_OUT,
-	DMACH_MIC_IN,
-	DMACH_USB_EP1,
-	DMACH_USB_EP2,
-	DMACH_USB_EP3,
-	DMACH_USB_EP4,
-	DMACH_UART0_SRC2,	/* s3c2412 second uart sources */
-	DMACH_UART1_SRC2,
-	DMACH_UART2_SRC2,
-	DMACH_UART3,		/* s3c2443 has extra uart */
-	DMACH_UART3_SRC2,
-	DMACH_SPI0_TX,		/* s3c2443/2416/2450 hsspi0 */
-	DMACH_SPI0_RX,		/* s3c2443/2416/2450 hsspi0 */
-	DMACH_SPI1_TX,		/* s3c2443/2450 hsspi1 */
-	DMACH_SPI1_RX,		/* s3c2443/2450 hsspi1 */
-	DMACH_MAX,		/* the end entry */
-};
-
-#endif /* __ASM_ARCH_DMA_H */
diff --git a/arch/arm/mach-s3c24xx/include/mach/gpio-samsung.h b/arch/arm/mach-s3c24xx/include/mach/gpio-samsung.h
deleted file mode 100644
index f8a114891f16..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/gpio-samsung.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2008 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - GPIO lib support
- */
-
-/* some boards require extra gpio capacity to support external
- * devices that need GPIO.
- */
-
-#ifndef GPIO_SAMSUNG_S3C24XX_H
-#define GPIO_SAMSUNG_S3C24XX_H
-
-#include <mach/map.h>
-
-/*
- * GPIO sizes for various SoCs:
- *
- *   2410 2412 2440 2443 2416
- *             2442
- *   ---- ---- ---- ---- ----
- * A  23   22   25   16   27
- * B  11   11   11   11   11
- * C  16   16   16   16   16
- * D  16   16   16   16   16
- * E  16   16   16   16   16
- * F  8    8    8    8    8
- * G  16   16   16   16   8
- * H  11   11   11   15   15
- * J  --   --   13   16   --
- * K  --   --   --   --   16
- * L  --   --   --   15   14
- * M  --   --   --   2    2
- */
-
-/* GPIO bank sizes */
-
-#define S3C2410_GPIO_A_NR	(32)
-#define S3C2410_GPIO_B_NR	(32)
-#define S3C2410_GPIO_C_NR	(32)
-#define S3C2410_GPIO_D_NR	(32)
-#define S3C2410_GPIO_E_NR	(32)
-#define S3C2410_GPIO_F_NR	(32)
-#define S3C2410_GPIO_G_NR	(32)
-#define S3C2410_GPIO_H_NR	(32)
-#define S3C2410_GPIO_J_NR	(32)	/* technically 16. */
-#define S3C2410_GPIO_K_NR	(32)	/* technically 16. */
-#define S3C2410_GPIO_L_NR	(32)	/* technically 15. */
-#define S3C2410_GPIO_M_NR	(32)	/* technically 2. */
-
-#if CONFIG_S3C_GPIO_SPACE != 0
-#error CONFIG_S3C_GPIO_SPACE cannot be nonzero at the moment
-#endif
-
-#define S3C2410_GPIO_NEXT(__gpio) \
-	((__gpio##_START) + (__gpio##_NR) + CONFIG_S3C_GPIO_SPACE + 0)
-
-#ifndef __ASSEMBLY__
-
-enum s3c_gpio_number {
-	S3C2410_GPIO_A_START = 0,
-	S3C2410_GPIO_B_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_A),
-	S3C2410_GPIO_C_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_B),
-	S3C2410_GPIO_D_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_C),
-	S3C2410_GPIO_E_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_D),
-	S3C2410_GPIO_F_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_E),
-	S3C2410_GPIO_G_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_F),
-	S3C2410_GPIO_H_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_G),
-	S3C2410_GPIO_J_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_H),
-	S3C2410_GPIO_K_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_J),
-	S3C2410_GPIO_L_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_K),
-	S3C2410_GPIO_M_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_L),
-};
-
-#endif /* __ASSEMBLY__ */
-
-/* S3C2410 GPIO number definitions. */
-
-#define S3C2410_GPA(_nr)	(S3C2410_GPIO_A_START + (_nr))
-#define S3C2410_GPB(_nr)	(S3C2410_GPIO_B_START + (_nr))
-#define S3C2410_GPC(_nr)	(S3C2410_GPIO_C_START + (_nr))
-#define S3C2410_GPD(_nr)	(S3C2410_GPIO_D_START + (_nr))
-#define S3C2410_GPE(_nr)	(S3C2410_GPIO_E_START + (_nr))
-#define S3C2410_GPF(_nr)	(S3C2410_GPIO_F_START + (_nr))
-#define S3C2410_GPG(_nr)	(S3C2410_GPIO_G_START + (_nr))
-#define S3C2410_GPH(_nr)	(S3C2410_GPIO_H_START + (_nr))
-#define S3C2410_GPJ(_nr)	(S3C2410_GPIO_J_START + (_nr))
-#define S3C2410_GPK(_nr)	(S3C2410_GPIO_K_START + (_nr))
-#define S3C2410_GPL(_nr)	(S3C2410_GPIO_L_START + (_nr))
-#define S3C2410_GPM(_nr)	(S3C2410_GPIO_M_START + (_nr))
-
-#ifdef CONFIG_CPU_S3C244X
-#define S3C_GPIO_END	(S3C2410_GPJ(0) + 32)
-#elif defined(CONFIG_CPU_S3C2443) || defined(CONFIG_CPU_S3C2416)
-#define S3C_GPIO_END	(S3C2410_GPM(0) + 32)
-#else
-#define S3C_GPIO_END	(S3C2410_GPH(0) + 32)
-#endif
-
-#endif /* GPIO_SAMSUNG_S3C24XX_H */
diff --git a/arch/arm/mach-s3c24xx/include/mach/hardware.h b/arch/arm/mach-s3c24xx/include/mach/hardware.h
deleted file mode 100644
index c732ea54984c..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/hardware.h
+++ /dev/null
@@ -1,14 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2003 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - hardware
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-extern unsigned int s3c2410_modify_misccr(unsigned int clr, unsigned int chg);
-
-#endif /* __ASM_ARCH_HARDWARE_H */
diff --git a/arch/arm/mach-s3c24xx/include/mach/io.h b/arch/arm/mach-s3c24xx/include/mach/io.h
deleted file mode 100644
index bcddf615adb6..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/io.h
+++ /dev/null
@@ -1,50 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * arch/arm/mach-s3c2410/include/mach/io.h
- *  from arch/arm/mach-rpc/include/mach/io.h
- *
- * Copyright (C) 1997 Russell King
- *	     (C) 2003 Simtec Electronics
-*/
-
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-#include <plat/map-base.h>
-
-/*
- * ISA style IO, for each machine to sort out mappings for,
- * if it implements it. We reserve two 16M regions for ISA,
- * so the PC/104 can use separate addresses for 8-bit and
- * 16-bit port I/O.
- */
-#define PCIO_BASE		S3C_ADDR(0x02000000)
-#define IO_SPACE_LIMIT		0x00ffffff
-#define S3C24XX_VA_ISA_WORD	(PCIO_BASE)
-#define S3C24XX_VA_ISA_BYTE	(PCIO_BASE + 0x01000000)
-
-#ifdef CONFIG_ISA
-
-#define inb(p)		readb(S3C24XX_VA_ISA_BYTE + (p))
-#define inw(p)		readw(S3C24XX_VA_ISA_WORD + (p))
-#define inl(p)		readl(S3C24XX_VA_ISA_WORD + (p))
-
-#define outb(v,p)	writeb((v), S3C24XX_VA_ISA_BYTE + (p))
-#define outw(v,p)	writew((v), S3C24XX_VA_ISA_WORD + (p))
-#define outl(v,p)	writel((v), S3C24XX_VA_ISA_WORD + (p))
-
-#define insb(p,d,l)	readsb(S3C24XX_VA_ISA_BYTE + (p),d,l)
-#define insw(p,d,l)	readsw(S3C24XX_VA_ISA_WORD + (p),d,l)
-#define insl(p,d,l)	readsl(S3C24XX_VA_ISA_WORD + (p),d,l)
-
-#define outsb(p,d,l)	writesb(S3C24XX_VA_ISA_BYTE + (p),d,l)
-#define outsw(p,d,l)	writesw(S3C24XX_VA_ISA_WORD + (p),d,l)
-#define outsl(p,d,l)	writesl(S3C24XX_VA_ISA_WORD + (p),d,l)
-
-#else
-
-#define __io(x) (PCIO_BASE + (x))
-
-#endif
-
-#endif
diff --git a/arch/arm/mach-s3c24xx/include/mach/irqs.h b/arch/arm/mach-s3c24xx/include/mach/irqs.h
deleted file mode 100644
index aaf3bae08b52..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/irqs.h
+++ /dev/null
@@ -1,213 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2003-2005 Simtec Electronics
- *   Ben Dooks <ben@simtec.co.uk>
- */
-
-
-#ifndef __ASM_ARCH_IRQS_H
-#define __ASM_ARCH_IRQS_H __FILE__
-
-/* we keep the first set of CPU IRQs out of the range of
- * the ISA space, so that the PC104 has them to itself
- * and we don't end up having to do horrible things to the
- * standard ISA drivers....
- */
-
-#define S3C2410_CPUIRQ_OFFSET	 (16)
-
-#define S3C2410_IRQ(x) ((x) + S3C2410_CPUIRQ_OFFSET)
-
-/* main cpu interrupts */
-#define IRQ_EINT0      S3C2410_IRQ(0)	    /* 16 */
-#define IRQ_EINT1      S3C2410_IRQ(1)
-#define IRQ_EINT2      S3C2410_IRQ(2)
-#define IRQ_EINT3      S3C2410_IRQ(3)
-#define IRQ_EINT4t7    S3C2410_IRQ(4)	    /* 20 */
-#define IRQ_EINT8t23   S3C2410_IRQ(5)
-#define IRQ_RESERVED6  S3C2410_IRQ(6)	    /* for s3c2410 */
-#define IRQ_CAM        S3C2410_IRQ(6)	    /* for s3c2440,s3c2443 */
-#define IRQ_BATT_FLT   S3C2410_IRQ(7)
-#define IRQ_TICK       S3C2410_IRQ(8)	    /* 24 */
-#define IRQ_WDT	       S3C2410_IRQ(9)	    /* WDT/AC97 for s3c2443 */
-#define IRQ_TIMER0     S3C2410_IRQ(10)
-#define IRQ_TIMER1     S3C2410_IRQ(11)
-#define IRQ_TIMER2     S3C2410_IRQ(12)
-#define IRQ_TIMER3     S3C2410_IRQ(13)
-#define IRQ_TIMER4     S3C2410_IRQ(14)
-#define IRQ_UART2      S3C2410_IRQ(15)
-#define IRQ_LCD	       S3C2410_IRQ(16)	    /* 32 */
-#define IRQ_DMA0       S3C2410_IRQ(17)	    /* IRQ_DMA for s3c2443 */
-#define IRQ_DMA1       S3C2410_IRQ(18)
-#define IRQ_DMA2       S3C2410_IRQ(19)
-#define IRQ_DMA3       S3C2410_IRQ(20)
-#define IRQ_SDI	       S3C2410_IRQ(21)
-#define IRQ_SPI0       S3C2410_IRQ(22)
-#define IRQ_UART1      S3C2410_IRQ(23)
-#define IRQ_RESERVED24 S3C2410_IRQ(24)	    /* 40 */
-#define IRQ_NFCON      S3C2410_IRQ(24)	    /* for s3c2440 */
-#define IRQ_USBD       S3C2410_IRQ(25)
-#define IRQ_USBH       S3C2410_IRQ(26)
-#define IRQ_IIC	       S3C2410_IRQ(27)
-#define IRQ_UART0      S3C2410_IRQ(28)	    /* 44 */
-#define IRQ_SPI1       S3C2410_IRQ(29)
-#define IRQ_RTC	       S3C2410_IRQ(30)
-#define IRQ_ADCPARENT  S3C2410_IRQ(31)
-
-/* interrupts generated from the external interrupts sources */
-#define IRQ_EINT0_2412 S3C2410_IRQ(32)
-#define IRQ_EINT1_2412 S3C2410_IRQ(33)
-#define IRQ_EINT2_2412 S3C2410_IRQ(34)
-#define IRQ_EINT3_2412 S3C2410_IRQ(35)
-#define IRQ_EINT4      S3C2410_IRQ(36)	   /* 52 */
-#define IRQ_EINT5      S3C2410_IRQ(37)
-#define IRQ_EINT6      S3C2410_IRQ(38)
-#define IRQ_EINT7      S3C2410_IRQ(39)
-#define IRQ_EINT8      S3C2410_IRQ(40)
-#define IRQ_EINT9      S3C2410_IRQ(41)
-#define IRQ_EINT10     S3C2410_IRQ(42)
-#define IRQ_EINT11     S3C2410_IRQ(43)
-#define IRQ_EINT12     S3C2410_IRQ(44)
-#define IRQ_EINT13     S3C2410_IRQ(45)
-#define IRQ_EINT14     S3C2410_IRQ(46)
-#define IRQ_EINT15     S3C2410_IRQ(47)
-#define IRQ_EINT16     S3C2410_IRQ(48)
-#define IRQ_EINT17     S3C2410_IRQ(49)
-#define IRQ_EINT18     S3C2410_IRQ(50)
-#define IRQ_EINT19     S3C2410_IRQ(51)
-#define IRQ_EINT20     S3C2410_IRQ(52)	   /* 68 */
-#define IRQ_EINT21     S3C2410_IRQ(53)
-#define IRQ_EINT22     S3C2410_IRQ(54)
-#define IRQ_EINT23     S3C2410_IRQ(55)
-
-#define IRQ_EINT_BIT(x)	((x) - IRQ_EINT4 + 4)
-#define IRQ_EINT(x)    (((x) >= 4) ? (IRQ_EINT4 + (x) - 4) : (IRQ_EINT0 + (x)))
-
-#define IRQ_LCD_FIFO   S3C2410_IRQ(56)
-#define IRQ_LCD_FRAME  S3C2410_IRQ(57)
-
-/* IRQs for the interal UARTs, and ADC
- * these need to be ordered in number of appearance in the
- * SUBSRC mask register
-*/
-
-#define S3C2410_IRQSUB(x)	S3C2410_IRQ((x)+58)
-
-#define IRQ_S3CUART_RX0		S3C2410_IRQSUB(0)	/* 74 */
-#define IRQ_S3CUART_TX0		S3C2410_IRQSUB(1)
-#define IRQ_S3CUART_ERR0	S3C2410_IRQSUB(2)
-
-#define IRQ_S3CUART_RX1		S3C2410_IRQSUB(3)	/* 77 */
-#define IRQ_S3CUART_TX1		S3C2410_IRQSUB(4)
-#define IRQ_S3CUART_ERR1	S3C2410_IRQSUB(5)
-
-#define IRQ_S3CUART_RX2		S3C2410_IRQSUB(6)	/* 80 */
-#define IRQ_S3CUART_TX2		S3C2410_IRQSUB(7)
-#define IRQ_S3CUART_ERR2	S3C2410_IRQSUB(8)
-
-#define IRQ_TC			S3C2410_IRQSUB(9)
-#define IRQ_ADC			S3C2410_IRQSUB(10)
-
-/* extra irqs for s3c2412 */
-
-#define IRQ_S3C2412_CFSDI	S3C2410_IRQ(21)
-
-#define IRQ_S3C2412_SDI		S3C2410_IRQSUB(13)
-#define IRQ_S3C2412_CF		S3C2410_IRQSUB(14)
-
-
-#define IRQ_S3C2416_EINT8t15	S3C2410_IRQ(5)
-#define IRQ_S3C2416_DMA		S3C2410_IRQ(17)
-#define IRQ_S3C2416_UART3	S3C2410_IRQ(18)
-#define IRQ_S3C2416_SDI1	S3C2410_IRQ(20)
-#define IRQ_S3C2416_SDI0	S3C2410_IRQ(21)
-
-#define IRQ_S3C2416_LCD2	S3C2410_IRQSUB(15)
-#define IRQ_S3C2416_LCD3	S3C2410_IRQSUB(16)
-#define IRQ_S3C2416_LCD4	S3C2410_IRQSUB(17)
-#define IRQ_S3C2416_DMA0	S3C2410_IRQSUB(18)
-#define IRQ_S3C2416_DMA1	S3C2410_IRQSUB(19)
-#define IRQ_S3C2416_DMA2	S3C2410_IRQSUB(20)
-#define IRQ_S3C2416_DMA3	S3C2410_IRQSUB(21)
-#define IRQ_S3C2416_DMA4	S3C2410_IRQSUB(22)
-#define IRQ_S3C2416_DMA5	S3C2410_IRQSUB(23)
-#define IRQ_S32416_WDT		S3C2410_IRQSUB(27)
-#define IRQ_S32416_AC97		S3C2410_IRQSUB(28)
-
-/* second interrupt-register of s3c2416/s3c2450 */
-
-#define S3C2416_IRQ(x)		S3C2410_IRQ((x) + 58 + 29)
-#define IRQ_S3C2416_2D		S3C2416_IRQ(0)
-#define IRQ_S3C2416_IIC1	S3C2416_IRQ(1)
-#define IRQ_S3C2416_RESERVED2	S3C2416_IRQ(2)
-#define IRQ_S3C2416_RESERVED3	S3C2416_IRQ(3)
-#define IRQ_S3C2416_PCM0	S3C2416_IRQ(4)
-#define IRQ_S3C2416_PCM1	S3C2416_IRQ(5)
-#define IRQ_S3C2416_I2S0	S3C2416_IRQ(6)
-#define IRQ_S3C2416_I2S1	S3C2416_IRQ(7)
-
-/* extra irqs for s3c2440 */
-
-#define IRQ_S3C2440_CAM_C	S3C2410_IRQSUB(11)	/* S3C2443 too */
-#define IRQ_S3C2440_CAM_P	S3C2410_IRQSUB(12)	/* S3C2443 too */
-#define IRQ_S3C2440_WDT		S3C2410_IRQSUB(13)
-#define IRQ_S3C2440_AC97	S3C2410_IRQSUB(14)
-
-/* irqs for s3c2443 */
-
-#define IRQ_S3C2443_DMA		S3C2410_IRQ(17)		/* IRQ_DMA1 */
-#define IRQ_S3C2443_UART3	S3C2410_IRQ(18)		/* IRQ_DMA2 */
-#define IRQ_S3C2443_CFCON	S3C2410_IRQ(19)		/* IRQ_DMA3 */
-#define IRQ_S3C2443_HSMMC	S3C2410_IRQ(20)		/* IRQ_SDI */
-#define IRQ_S3C2443_NAND	S3C2410_IRQ(24)		/* reserved */
-
-#define IRQ_S3C2416_HSMMC0	S3C2410_IRQ(21)		/* S3C2416/S3C2450 */
-
-#define IRQ_HSMMC0		IRQ_S3C2416_HSMMC0
-#define IRQ_HSMMC1		IRQ_S3C2443_HSMMC
-
-#define IRQ_S3C2443_LCD1	S3C2410_IRQSUB(14)
-#define IRQ_S3C2443_LCD2	S3C2410_IRQSUB(15)
-#define IRQ_S3C2443_LCD3	S3C2410_IRQSUB(16)
-#define IRQ_S3C2443_LCD4	S3C2410_IRQSUB(17)
-
-#define IRQ_S3C2443_DMA0	S3C2410_IRQSUB(18)
-#define IRQ_S3C2443_DMA1	S3C2410_IRQSUB(19)
-#define IRQ_S3C2443_DMA2	S3C2410_IRQSUB(20)
-#define IRQ_S3C2443_DMA3	S3C2410_IRQSUB(21)
-#define IRQ_S3C2443_DMA4	S3C2410_IRQSUB(22)
-#define IRQ_S3C2443_DMA5	S3C2410_IRQSUB(23)
-
-/* UART3 */
-#define IRQ_S3C2443_RX3		S3C2410_IRQSUB(24)
-#define IRQ_S3C2443_TX3		S3C2410_IRQSUB(25)
-#define IRQ_S3C2443_ERR3	S3C2410_IRQSUB(26)
-
-#define IRQ_S3C2443_WDT		S3C2410_IRQSUB(27)
-#define IRQ_S3C2443_AC97	S3C2410_IRQSUB(28)
-
-#if defined(CONFIG_CPU_S3C2416)
-#define NR_IRQS (IRQ_S3C2416_I2S1 + 1)
-#else
-#define NR_IRQS (IRQ_S3C2443_AC97 + 1)
-#endif
-
-/* compatibility define. */
-#define IRQ_UART3		IRQ_S3C2443_UART3
-#define IRQ_S3CUART_RX3		IRQ_S3C2443_RX3
-#define IRQ_S3CUART_TX3		IRQ_S3C2443_TX3
-#define IRQ_S3CUART_ERR3	IRQ_S3C2443_ERR3
-
-#define IRQ_LCD_VSYNC		IRQ_S3C2443_LCD3
-#define IRQ_LCD_SYSTEM		IRQ_S3C2443_LCD2
-
-#ifdef CONFIG_CPU_S3C2440
-#define IRQ_S3C244X_AC97 IRQ_S3C2440_AC97
-#else
-#define IRQ_S3C244X_AC97 IRQ_S3C2443_AC97
-#endif
-
-/* Our FIQs are routable from IRQ_EINT0 to IRQ_ADCPARENT */
-#define FIQ_START		IRQ_EINT0
-
-#endif /* __ASM_ARCH_IRQ_H */
diff --git a/arch/arm/mach-s3c24xx/include/mach/map.h b/arch/arm/mach-s3c24xx/include/mach/map.h
deleted file mode 100644
index a20c9fd0d855..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/map.h
+++ /dev/null
@@ -1,159 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2003 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - Memory map definitions
- */
-
-#ifndef __ASM_ARCH_MAP_H
-#define __ASM_ARCH_MAP_H
-
-#include <plat/map-base.h>
-#include <plat/map-s3c.h>
-
-/*
- * interrupt controller is the first thing we put in, to make
- * the assembly code for the irq detection easier
- */
-#define S3C2410_PA_IRQ		(0x4A000000)
-#define S3C24XX_SZ_IRQ		SZ_1M
-
-/* memory controller registers */
-#define S3C2410_PA_MEMCTRL	(0x48000000)
-#define S3C24XX_SZ_MEMCTRL	SZ_1M
-
-/* Timers */
-#define S3C2410_PA_TIMER	(0x51000000)
-#define S3C24XX_SZ_TIMER	SZ_1M
-
-/* Clock and Power management */
-#define S3C24XX_SZ_CLKPWR	SZ_1M
-
-/* USB Device port */
-#define S3C2410_PA_USBDEV	(0x52000000)
-#define S3C24XX_SZ_USBDEV	SZ_1M
-
-/* Watchdog */
-#define S3C2410_PA_WATCHDOG	(0x53000000)
-#define S3C24XX_SZ_WATCHDOG	SZ_1M
-
-/* Standard size definitions for peripheral blocks. */
-
-#define S3C24XX_SZ_UART		SZ_1M
-#define S3C24XX_SZ_IIS		SZ_1M
-#define S3C24XX_SZ_ADC		SZ_1M
-#define S3C24XX_SZ_SPI		SZ_1M
-#define S3C24XX_SZ_SDI		SZ_1M
-#define S3C24XX_SZ_NAND		SZ_1M
-#define S3C24XX_SZ_GPIO		SZ_1M
-
-/* USB host controller */
-#define S3C2410_PA_USBHOST (0x49000000)
-
-/* S3C2416/S3C2443/S3C2450 High-Speed USB Gadget */
-#define S3C2416_PA_HSUDC	(0x49800000)
-#define S3C2416_SZ_HSUDC	(SZ_4K)
-
-/* DMA controller */
-#define S3C2410_PA_DMA	   (0x4B000000)
-#define S3C24XX_SZ_DMA	   SZ_1M
-
-/* Clock and Power management */
-#define S3C2410_PA_CLKPWR  (0x4C000000)
-
-/* LCD controller */
-#define S3C2410_PA_LCD	   (0x4D000000)
-#define S3C24XX_SZ_LCD	   SZ_1M
-
-/* NAND flash controller */
-#define S3C2410_PA_NAND	   (0x4E000000)
-
-/* IIC hardware controller */
-#define S3C2410_PA_IIC	   (0x54000000)
-
-/* IIS controller */
-#define S3C2410_PA_IIS	   (0x55000000)
-
-/* RTC */
-#define S3C2410_PA_RTC	   (0x57000000)
-#define S3C24XX_SZ_RTC	   SZ_1M
-
-/* ADC */
-#define S3C2410_PA_ADC	   (0x58000000)
-
-/* SPI */
-#define S3C2410_PA_SPI	   (0x59000000)
-#define S3C2443_PA_SPI0		(0x52000000)
-#define S3C2443_PA_SPI1		S3C2410_PA_SPI
-#define S3C2410_SPI1		(0x20)
-#define S3C2412_SPI1		(0x100)
-
-/* SDI */
-#define S3C2410_PA_SDI	   (0x5A000000)
-
-/* CAMIF */
-#define S3C2440_PA_CAMIF   (0x4F000000)
-#define S3C2440_SZ_CAMIF   SZ_1M
-
-/* AC97 */
-
-#define S3C2440_PA_AC97	   (0x5B000000)
-#define S3C2440_SZ_AC97	   SZ_1M
-
-/* S3C2443/S3C2416 High-speed SD/MMC */
-#define S3C2443_PA_HSMMC   (0x4A800000)
-#define S3C2416_PA_HSMMC0  (0x4AC00000)
-
-#define	S3C2443_PA_FB	(0x4C800000)
-
-/* S3C2412 memory and IO controls */
-#define S3C2412_PA_SSMC	(0x4F000000)
-
-#define S3C2412_PA_EBI	(0x48800000)
-
-/* physical addresses of all the chip-select areas */
-
-#define S3C2410_CS0 (0x00000000)
-#define S3C2410_CS1 (0x08000000)
-#define S3C2410_CS2 (0x10000000)
-#define S3C2410_CS3 (0x18000000)
-#define S3C2410_CS4 (0x20000000)
-#define S3C2410_CS5 (0x28000000)
-#define S3C2410_CS6 (0x30000000)
-#define S3C2410_CS7 (0x38000000)
-
-#define S3C2410_SDRAM_PA    (S3C2410_CS6)
-
-/* Use a single interface for common resources between S3C24XX cpus */
-
-#define S3C24XX_PA_IRQ      S3C2410_PA_IRQ
-#define S3C24XX_PA_MEMCTRL  S3C2410_PA_MEMCTRL
-#define S3C24XX_PA_DMA      S3C2410_PA_DMA
-#define S3C24XX_PA_CLKPWR   S3C2410_PA_CLKPWR
-#define S3C24XX_PA_LCD      S3C2410_PA_LCD
-#define S3C24XX_PA_TIMER    S3C2410_PA_TIMER
-#define S3C24XX_PA_USBDEV   S3C2410_PA_USBDEV
-#define S3C24XX_PA_WATCHDOG S3C2410_PA_WATCHDOG
-#define S3C24XX_PA_IIS      S3C2410_PA_IIS
-#define S3C24XX_PA_RTC      S3C2410_PA_RTC
-#define S3C24XX_PA_ADC      S3C2410_PA_ADC
-#define S3C24XX_PA_SPI      S3C2410_PA_SPI
-#define S3C24XX_PA_SPI1		(S3C2410_PA_SPI + S3C2410_SPI1)
-#define S3C24XX_PA_SDI      S3C2410_PA_SDI
-#define S3C24XX_PA_NAND	    S3C2410_PA_NAND
-
-#define S3C_PA_FB	    S3C2443_PA_FB
-#define S3C_PA_IIC          S3C2410_PA_IIC
-#define S3C_PA_USBHOST	S3C2410_PA_USBHOST
-#define S3C_PA_HSMMC0	    S3C2416_PA_HSMMC0
-#define S3C_PA_HSMMC1	    S3C2443_PA_HSMMC
-#define S3C_PA_WDT	    S3C2410_PA_WATCHDOG
-#define S3C_PA_NAND	    S3C24XX_PA_NAND
-
-#define S3C_PA_SPI0		S3C2443_PA_SPI0
-#define S3C_PA_SPI1		S3C2443_PA_SPI1
-
-#define SAMSUNG_PA_TIMER	S3C2410_PA_TIMER
-
-#endif /* __ASM_ARCH_MAP_H */
diff --git a/arch/arm/mach-s3c24xx/include/mach/pm-core.h b/arch/arm/mach-s3c24xx/include/mach/pm-core.h
deleted file mode 100644
index a22b4a37ee57..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/pm-core.h
+++ /dev/null
@@ -1,96 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright 2008 Simtec Electronics
- *      Ben Dooks <ben@simtec.co.uk>
- *      http://armlinux.simtec.co.uk/
- *
- * S3C24xx - PM core support for arch/arm/plat-s3c/pm.c
- */
-
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include "regs-clock.h"
-#include "regs-irq.h"
-#include <mach/irqs.h>
-
-static inline void s3c_pm_debug_init_uart(void)
-{
-#ifdef CONFIG_SAMSUNG_PM_DEBUG
-	unsigned long tmp = __raw_readl(S3C2410_CLKCON);
-
-	/* re-start uart clocks */
-	tmp |= S3C2410_CLKCON_UART0;
-	tmp |= S3C2410_CLKCON_UART1;
-	tmp |= S3C2410_CLKCON_UART2;
-
-	__raw_writel(tmp, S3C2410_CLKCON);
-	udelay(10);
-#endif
-}
-
-static inline void s3c_pm_arch_prepare_irqs(void)
-{
-	__raw_writel(s3c_irqwake_intmask, S3C2410_INTMSK);
-	__raw_writel(s3c_irqwake_eintmask, S3C2410_EINTMASK);
-
-	/* ack any outstanding external interrupts before we go to sleep */
-
-	__raw_writel(__raw_readl(S3C2410_EINTPEND), S3C2410_EINTPEND);
-	__raw_writel(__raw_readl(S3C2410_INTPND), S3C2410_INTPND);
-	__raw_writel(__raw_readl(S3C2410_SRCPND), S3C2410_SRCPND);
-
-}
-
-static inline void s3c_pm_arch_stop_clocks(void)
-{
-	__raw_writel(0x00, S3C2410_CLKCON);  /* turn off clocks over sleep */
-}
-
-/* s3c2410_pm_show_resume_irqs
- *
- * print any IRQs asserted at resume time (ie, we woke from)
-*/
-static inline void s3c_pm_show_resume_irqs(int start, unsigned long which,
-					   unsigned long mask)
-{
-	int i;
-
-	which &= ~mask;
-
-	for (i = 0; i <= 31; i++) {
-		if (which & (1L<<i)) {
-			S3C_PMDBG("IRQ %d asserted at resume\n", start+i);
-		}
-	}
-}
-
-static inline void s3c_pm_arch_show_resume_irqs(void)
-{
-	S3C_PMDBG("post sleep: IRQs 0x%08x, 0x%08x\n",
-		  __raw_readl(S3C2410_SRCPND),
-		  __raw_readl(S3C2410_EINTPEND));
-
-	s3c_pm_show_resume_irqs(IRQ_EINT0, __raw_readl(S3C2410_SRCPND),
-				s3c_irqwake_intmask);
-
-	s3c_pm_show_resume_irqs(IRQ_EINT4-4, __raw_readl(S3C2410_EINTPEND),
-				s3c_irqwake_eintmask);
-}
-
-static inline void s3c_pm_restored_gpios(void) { }
-static inline void samsung_pm_saved_gpios(void) { }
-
-/* state for IRQs over sleep */
-
-/* default is to allow for EINT0..EINT15, and IRQ_RTC as wakeup sources
- *
- * set bit to 1 in allow bitfield to enable the wakeup settings on it
-*/
-#ifdef CONFIG_PM_SLEEP
-#define s3c_irqwake_intallow	(1L << 30 | 0xfL)
-#define s3c_irqwake_eintallow	(0x0000fff0L)
-#else
-#define s3c_irqwake_eintallow 0
-#define s3c_irqwake_intallow  0
-#endif
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-clock.h b/arch/arm/mach-s3c24xx/include/mach/regs-clock.h
deleted file mode 100644
index da4e7b3aeba6..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/regs-clock.h
+++ /dev/null
@@ -1,146 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2003-2006 Simtec Electronics <linux@simtec.co.uk>
- *	http://armlinux.simtec.co.uk/
- *
- * S3C2410 clock register definitions
- */
-
-#ifndef __ASM_ARM_REGS_CLOCK
-#define __ASM_ARM_REGS_CLOCK
-
-#include <mach/map.h>
-
-#define S3C2410_CLKREG(x) ((x) + S3C24XX_VA_CLKPWR)
-
-#define S3C2410_PLLVAL(_m,_p,_s) ((_m) << 12 | ((_p) << 4) | ((_s)))
-
-#define S3C2410_LOCKTIME    S3C2410_CLKREG(0x00)
-#define S3C2410_MPLLCON	    S3C2410_CLKREG(0x04)
-#define S3C2410_UPLLCON	    S3C2410_CLKREG(0x08)
-#define S3C2410_CLKCON	    S3C2410_CLKREG(0x0C)
-#define S3C2410_CLKSLOW	    S3C2410_CLKREG(0x10)
-#define S3C2410_CLKDIVN	    S3C2410_CLKREG(0x14)
-
-#define S3C2410_CLKCON_IDLE	     (1<<2)
-#define S3C2410_CLKCON_POWER	     (1<<3)
-#define S3C2410_CLKCON_NAND	     (1<<4)
-#define S3C2410_CLKCON_LCDC	     (1<<5)
-#define S3C2410_CLKCON_USBH	     (1<<6)
-#define S3C2410_CLKCON_USBD	     (1<<7)
-#define S3C2410_CLKCON_PWMT	     (1<<8)
-#define S3C2410_CLKCON_SDI	     (1<<9)
-#define S3C2410_CLKCON_UART0	     (1<<10)
-#define S3C2410_CLKCON_UART1	     (1<<11)
-#define S3C2410_CLKCON_UART2	     (1<<12)
-#define S3C2410_CLKCON_GPIO	     (1<<13)
-#define S3C2410_CLKCON_RTC	     (1<<14)
-#define S3C2410_CLKCON_ADC	     (1<<15)
-#define S3C2410_CLKCON_IIC	     (1<<16)
-#define S3C2410_CLKCON_IIS	     (1<<17)
-#define S3C2410_CLKCON_SPI	     (1<<18)
-
-#define S3C2410_CLKDIVN_PDIVN	     (1<<0)
-#define S3C2410_CLKDIVN_HDIVN	     (1<<1)
-
-#define S3C2410_CLKSLOW_UCLK_OFF	(1<<7)
-#define S3C2410_CLKSLOW_MPLL_OFF	(1<<5)
-#define S3C2410_CLKSLOW_SLOW		(1<<4)
-#define S3C2410_CLKSLOW_SLOWVAL(x)	(x)
-#define S3C2410_CLKSLOW_GET_SLOWVAL(x)	((x) & 7)
-
-#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442)
-
-/* extra registers */
-#define S3C2440_CAMDIVN	    S3C2410_CLKREG(0x18)
-
-#define S3C2440_CLKCON_CAMERA        (1<<19)
-#define S3C2440_CLKCON_AC97          (1<<20)
-
-#define S3C2440_CLKDIVN_PDIVN	     (1<<0)
-#define S3C2440_CLKDIVN_HDIVN_MASK   (3<<1)
-#define S3C2440_CLKDIVN_HDIVN_1      (0<<1)
-#define S3C2440_CLKDIVN_HDIVN_2      (1<<1)
-#define S3C2440_CLKDIVN_HDIVN_4_8    (2<<1)
-#define S3C2440_CLKDIVN_HDIVN_3_6    (3<<1)
-#define S3C2440_CLKDIVN_UCLK         (1<<3)
-
-#define S3C2440_CAMDIVN_CAMCLK_MASK  (0xf<<0)
-#define S3C2440_CAMDIVN_CAMCLK_SEL   (1<<4)
-#define S3C2440_CAMDIVN_HCLK3_HALF   (1<<8)
-#define S3C2440_CAMDIVN_HCLK4_HALF   (1<<9)
-#define S3C2440_CAMDIVN_DVSEN        (1<<12)
-
-#define S3C2442_CAMDIVN_CAMCLK_DIV3  (1<<5)
-
-#endif /* CONFIG_CPU_S3C2440 or CONFIG_CPU_S3C2442 */
-
-#if defined(CONFIG_CPU_S3C2412)
-
-#define S3C2412_OSCSET		S3C2410_CLKREG(0x18)
-#define S3C2412_CLKSRC		S3C2410_CLKREG(0x1C)
-
-#define S3C2412_PLLCON_OFF		(1<<20)
-
-#define S3C2412_CLKDIVN_PDIVN		(1<<2)
-#define S3C2412_CLKDIVN_HDIVN_MASK	(3<<0)
-#define S3C2412_CLKDIVN_ARMDIVN		(1<<3)
-#define S3C2412_CLKDIVN_DVSEN		(1<<4)
-#define S3C2412_CLKDIVN_HALFHCLK	(1<<5)
-#define S3C2412_CLKDIVN_USB48DIV	(1<<6)
-#define S3C2412_CLKDIVN_UARTDIV_MASK	(15<<8)
-#define S3C2412_CLKDIVN_UARTDIV_SHIFT	(8)
-#define S3C2412_CLKDIVN_I2SDIV_MASK	(15<<12)
-#define S3C2412_CLKDIVN_I2SDIV_SHIFT	(12)
-#define S3C2412_CLKDIVN_CAMDIV_MASK	(15<<16)
-#define S3C2412_CLKDIVN_CAMDIV_SHIFT	(16)
-
-#define S3C2412_CLKCON_WDT		(1<<28)
-#define S3C2412_CLKCON_SPI		(1<<27)
-#define S3C2412_CLKCON_IIS		(1<<26)
-#define S3C2412_CLKCON_IIC		(1<<25)
-#define S3C2412_CLKCON_ADC		(1<<24)
-#define S3C2412_CLKCON_RTC		(1<<23)
-#define S3C2412_CLKCON_GPIO		(1<<22)
-#define S3C2412_CLKCON_UART2		(1<<21)
-#define S3C2412_CLKCON_UART1		(1<<20)
-#define S3C2412_CLKCON_UART0		(1<<19)
-#define S3C2412_CLKCON_SDI		(1<<18)
-#define S3C2412_CLKCON_PWMT		(1<<17)
-#define S3C2412_CLKCON_USBD		(1<<16)
-#define S3C2412_CLKCON_CAMCLK		(1<<15)
-#define S3C2412_CLKCON_UARTCLK		(1<<14)
-/* missing 13 */
-#define S3C2412_CLKCON_USB_HOST48	(1<<12)
-#define S3C2412_CLKCON_USB_DEV48	(1<<11)
-#define S3C2412_CLKCON_HCLKdiv2		(1<<10)
-#define S3C2412_CLKCON_HCLKx2		(1<<9)
-#define S3C2412_CLKCON_SDRAM		(1<<8)
-/* missing 7 */
-#define S3C2412_CLKCON_USBH		S3C2410_CLKCON_USBH
-#define S3C2412_CLKCON_LCDC		S3C2410_CLKCON_LCDC
-#define S3C2412_CLKCON_NAND		S3C2410_CLKCON_NAND
-#define S3C2412_CLKCON_DMA3		(1<<3)
-#define S3C2412_CLKCON_DMA2		(1<<2)
-#define S3C2412_CLKCON_DMA1		(1<<1)
-#define S3C2412_CLKCON_DMA0		(1<<0)
-
-/* clock sourec controls */
-
-#define S3C2412_CLKSRC_EXTCLKDIV_MASK		(7 << 0)
-#define S3C2412_CLKSRC_EXTCLKDIV_SHIFT		(0)
-#define S3C2412_CLKSRC_MDIVCLK_EXTCLKDIV	(1<<3)
-#define S3C2412_CLKSRC_MSYSCLK_MPLL		(1<<4)
-#define S3C2412_CLKSRC_USYSCLK_UPLL		(1<<5)
-#define S3C2412_CLKSRC_UARTCLK_MPLL		(1<<8)
-#define S3C2412_CLKSRC_I2SCLK_MPLL		(1<<9)
-#define S3C2412_CLKSRC_USBCLK_HCLK		(1<<10)
-#define S3C2412_CLKSRC_CAMCLK_HCLK		(1<<11)
-#define S3C2412_CLKSRC_UREFCLK_EXTCLK	(1<<12)
-#define S3C2412_CLKSRC_EREFCLK_EXTCLK	(1<<14)
-
-#endif /* CONFIG_CPU_S3C2412 */
-
-#define S3C2416_CLKDIV2		S3C2410_CLKREG(0x28)
-
-#endif /* __ASM_ARM_REGS_CLOCK */
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-gpio.h b/arch/arm/mach-s3c24xx/include/mach/regs-gpio.h
deleted file mode 100644
index 51827d5577b6..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/regs-gpio.h
+++ /dev/null
@@ -1,608 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2003-2004 Simtec Electronics <linux@simtec.co.uk>
- *	http://www.simtec.co.uk/products/SWLINUX/
- *
- * S3C2410 GPIO register definitions
- */
-
-
-#ifndef __ASM_ARCH_REGS_GPIO_H
-#define __ASM_ARCH_REGS_GPIO_H
-
-#include <plat/map-s3c.h>
-
-#define S3C24XX_MISCCR		S3C24XX_GPIOREG2(0x80)
-
-/* general configuration options */
-
-#define S3C2410_GPIO_LEAVE   (0xFFFFFFFF)
-#define S3C2410_GPIO_INPUT   (0xFFFFFFF0)	/* not available on A */
-#define S3C2410_GPIO_OUTPUT  (0xFFFFFFF1)
-#define S3C2410_GPIO_IRQ     (0xFFFFFFF2)	/* not available for all */
-#define S3C2410_GPIO_SFN2    (0xFFFFFFF2)	/* bank A => addr/cs/nand */
-#define S3C2410_GPIO_SFN3    (0xFFFFFFF3)	/* not available on A */
-
-/* register address for the GPIO registers.
- * S3C24XX_GPIOREG2 is for the second set of registers in the
- * GPIO which move between s3c2410 and s3c2412 type systems */
-
-#define S3C2410_GPIOREG(x) ((x) + S3C24XX_VA_GPIO)
-#define S3C24XX_GPIOREG2(x) ((x) + S3C24XX_VA_GPIO2)
-
-
-/* configure GPIO ports A..G */
-
-/* port A - S3C2410: 22bits, zero in bit X makes pin X output
- * 1 makes port special function, this is default
-*/
-#define S3C2410_GPACON	   S3C2410_GPIOREG(0x00)
-#define S3C2410_GPADAT	   S3C2410_GPIOREG(0x04)
-
-#define S3C2410_GPA0_ADDR0   (1<<0)
-#define S3C2410_GPA1_ADDR16  (1<<1)
-#define S3C2410_GPA2_ADDR17  (1<<2)
-#define S3C2410_GPA3_ADDR18  (1<<3)
-#define S3C2410_GPA4_ADDR19  (1<<4)
-#define S3C2410_GPA5_ADDR20  (1<<5)
-#define S3C2410_GPA6_ADDR21  (1<<6)
-#define S3C2410_GPA7_ADDR22  (1<<7)
-#define S3C2410_GPA8_ADDR23  (1<<8)
-#define S3C2410_GPA9_ADDR24  (1<<9)
-#define S3C2410_GPA10_ADDR25 (1<<10)
-#define S3C2410_GPA11_ADDR26 (1<<11)
-#define S3C2410_GPA12_nGCS1  (1<<12)
-#define S3C2410_GPA13_nGCS2  (1<<13)
-#define S3C2410_GPA14_nGCS3  (1<<14)
-#define S3C2410_GPA15_nGCS4  (1<<15)
-#define S3C2410_GPA16_nGCS5  (1<<16)
-#define S3C2410_GPA17_CLE    (1<<17)
-#define S3C2410_GPA18_ALE    (1<<18)
-#define S3C2410_GPA19_nFWE   (1<<19)
-#define S3C2410_GPA20_nFRE   (1<<20)
-#define S3C2410_GPA21_nRSTOUT (1<<21)
-#define S3C2410_GPA22_nFCE   (1<<22)
-
-/* 0x08 and 0x0c are reserved on S3C2410 */
-
-/* S3C2410:
- * GPB is 10 IO pins, each configured by 2 bits each in GPBCON.
- *   00 = input, 01 = output, 10=special function, 11=reserved
-
- * bit 0,1 = pin 0, 2,3= pin 1...
- *
- * CPBUP = pull up resistor control, 1=disabled, 0=enabled
-*/
-
-#define S3C2410_GPBCON	   S3C2410_GPIOREG(0x10)
-#define S3C2410_GPBDAT	   S3C2410_GPIOREG(0x14)
-#define S3C2410_GPBUP	   S3C2410_GPIOREG(0x18)
-
-/* no i/o pin in port b can have value 3 (unless it is a s3c2443) ! */
-
-#define S3C2410_GPB0_TOUT0   (0x02 << 0)
-
-#define S3C2410_GPB1_TOUT1   (0x02 << 2)
-
-#define S3C2410_GPB2_TOUT2   (0x02 << 4)
-
-#define S3C2410_GPB3_TOUT3   (0x02 << 6)
-
-#define S3C2410_GPB4_TCLK0   (0x02 << 8)
-#define S3C2410_GPB4_MASK    (0x03 << 8)
-
-#define S3C2410_GPB5_nXBACK  (0x02 << 10)
-#define S3C2443_GPB5_XBACK   (0x03 << 10)
-
-#define S3C2410_GPB6_nXBREQ  (0x02 << 12)
-#define S3C2443_GPB6_XBREQ   (0x03 << 12)
-
-#define S3C2410_GPB7_nXDACK1 (0x02 << 14)
-#define S3C2443_GPB7_XDACK1  (0x03 << 14)
-
-#define S3C2410_GPB8_nXDREQ1 (0x02 << 16)
-
-#define S3C2410_GPB9_nXDACK0 (0x02 << 18)
-#define S3C2443_GPB9_XDACK0  (0x03 << 18)
-
-#define S3C2410_GPB10_nXDRE0 (0x02 << 20)
-#define S3C2443_GPB10_XDREQ0 (0x03 << 20)
-
-#define S3C2410_GPB_PUPDIS(x)  (1<<(x))
-
-/* Port C consits of 16 GPIO/Special function
- *
- * almost identical setup to port b, but the special functions are mostly
- * to do with the video system's sync/etc.
-*/
-
-#define S3C2410_GPCCON	   S3C2410_GPIOREG(0x20)
-#define S3C2410_GPCDAT	   S3C2410_GPIOREG(0x24)
-#define S3C2410_GPCUP	   S3C2410_GPIOREG(0x28)
-#define S3C2410_GPC0_LEND	(0x02 << 0)
-#define S3C2410_GPC1_VCLK	(0x02 << 2)
-#define S3C2410_GPC2_VLINE	(0x02 << 4)
-#define S3C2410_GPC3_VFRAME	(0x02 << 6)
-#define S3C2410_GPC4_VM		(0x02 << 8)
-#define S3C2410_GPC5_LCDVF0	(0x02 << 10)
-#define S3C2410_GPC6_LCDVF1	(0x02 << 12)
-#define S3C2410_GPC7_LCDVF2	(0x02 << 14)
-#define S3C2410_GPC8_VD0	(0x02 << 16)
-#define S3C2410_GPC9_VD1	(0x02 << 18)
-#define S3C2410_GPC10_VD2	(0x02 << 20)
-#define S3C2410_GPC11_VD3	(0x02 << 22)
-#define S3C2410_GPC12_VD4	(0x02 << 24)
-#define S3C2410_GPC13_VD5	(0x02 << 26)
-#define S3C2410_GPC14_VD6	(0x02 << 28)
-#define S3C2410_GPC15_VD7	(0x02 << 30)
-#define S3C2410_GPC_PUPDIS(x)  (1<<(x))
-
-/*
- * S3C2410: Port D consists of 16 GPIO/Special function
- *
- * almost identical setup to port b, but the special functions are mostly
- * to do with the video system's data.
- *
- * almost identical setup to port c
-*/
-
-#define S3C2410_GPDCON	   S3C2410_GPIOREG(0x30)
-#define S3C2410_GPDDAT	   S3C2410_GPIOREG(0x34)
-#define S3C2410_GPDUP	   S3C2410_GPIOREG(0x38)
-
-#define S3C2410_GPD0_VD8	(0x02 << 0)
-#define S3C2442_GPD0_nSPICS1	(0x03 << 0)
-
-#define S3C2410_GPD1_VD9	(0x02 << 2)
-#define S3C2442_GPD1_SPICLK1	(0x03 << 2)
-
-#define S3C2410_GPD2_VD10	(0x02 << 4)
-
-#define S3C2410_GPD3_VD11	(0x02 << 6)
-
-#define S3C2410_GPD4_VD12	(0x02 << 8)
-
-#define S3C2410_GPD5_VD13	(0x02 << 10)
-
-#define S3C2410_GPD6_VD14	(0x02 << 12)
-
-#define S3C2410_GPD7_VD15	(0x02 << 14)
-
-#define S3C2410_GPD8_VD16	(0x02 << 16)
-#define S3C2440_GPD8_SPIMISO1	(0x03 << 16)
-
-#define S3C2410_GPD9_VD17	(0x02 << 18)
-#define S3C2440_GPD9_SPIMOSI1	(0x03 << 18)
-
-#define S3C2410_GPD10_VD18	(0x02 << 20)
-#define S3C2440_GPD10_SPICLK1	(0x03 << 20)
-
-#define S3C2410_GPD11_VD19	(0x02 << 22)
-
-#define S3C2410_GPD12_VD20	(0x02 << 24)
-
-#define S3C2410_GPD13_VD21	(0x02 << 26)
-
-#define S3C2410_GPD14_VD22	(0x02 << 28)
-#define S3C2410_GPD14_nSS1	(0x03 << 28)
-
-#define S3C2410_GPD15_VD23	(0x02 << 30)
-#define S3C2410_GPD15_nSS0	(0x03 << 30)
-
-#define S3C2410_GPD_PUPDIS(x)  (1<<(x))
-
-/* S3C2410:
- * Port E consists of 16 GPIO/Special function
- *
- * again, the same as port B, but dealing with I2S, SDI, and
- * more miscellaneous functions
- *
- * GPIO / interrupt inputs
-*/
-
-#define S3C2410_GPECON	   S3C2410_GPIOREG(0x40)
-#define S3C2410_GPEDAT	   S3C2410_GPIOREG(0x44)
-#define S3C2410_GPEUP	   S3C2410_GPIOREG(0x48)
-
-#define S3C2410_GPE0_I2SLRCK   (0x02 << 0)
-#define S3C2443_GPE0_AC_nRESET (0x03 << 0)
-#define S3C2410_GPE0_MASK      (0x03 << 0)
-
-#define S3C2410_GPE1_I2SSCLK   (0x02 << 2)
-#define S3C2443_GPE1_AC_SYNC   (0x03 << 2)
-#define S3C2410_GPE1_MASK      (0x03 << 2)
-
-#define S3C2410_GPE2_CDCLK     (0x02 << 4)
-#define S3C2443_GPE2_AC_BITCLK (0x03 << 4)
-
-#define S3C2410_GPE3_I2SSDI    (0x02 << 6)
-#define S3C2443_GPE3_AC_SDI    (0x03 << 6)
-#define S3C2410_GPE3_nSS0      (0x03 << 6)
-#define S3C2410_GPE3_MASK      (0x03 << 6)
-
-#define S3C2410_GPE4_I2SSDO    (0x02 << 8)
-#define S3C2443_GPE4_AC_SDO    (0x03 << 8)
-#define S3C2410_GPE4_I2SSDI    (0x03 << 8)
-#define S3C2410_GPE4_MASK      (0x03 << 8)
-
-#define S3C2410_GPE5_SDCLK     (0x02 << 10)
-#define S3C2443_GPE5_SD1_CLK   (0x02 << 10)
-#define S3C2443_GPE5_AC_BITCLK (0x03 << 10)
-
-#define S3C2410_GPE6_SDCMD     (0x02 << 12)
-#define S3C2443_GPE6_SD1_CMD   (0x02 << 12)
-#define S3C2443_GPE6_AC_SDI    (0x03 << 12)
-
-#define S3C2410_GPE7_SDDAT0    (0x02 << 14)
-#define S3C2443_GPE5_SD1_DAT0  (0x02 << 14)
-#define S3C2443_GPE7_AC_SDO    (0x03 << 14)
-
-#define S3C2410_GPE8_SDDAT1    (0x02 << 16)
-#define S3C2443_GPE8_SD1_DAT1  (0x02 << 16)
-#define S3C2443_GPE8_AC_SYNC   (0x03 << 16)
-
-#define S3C2410_GPE9_SDDAT2    (0x02 << 18)
-#define S3C2443_GPE9_SD1_DAT2  (0x02 << 18)
-#define S3C2443_GPE9_AC_nRESET (0x03 << 18)
-
-#define S3C2410_GPE10_SDDAT3   (0x02 << 20)
-#define S3C2443_GPE10_SD1_DAT3 (0x02 << 20)
-
-#define S3C2410_GPE11_SPIMISO0 (0x02 << 22)
-
-#define S3C2410_GPE12_SPIMOSI0 (0x02 << 24)
-
-#define S3C2410_GPE13_SPICLK0  (0x02 << 26)
-
-#define S3C2410_GPE14_IICSCL   (0x02 << 28)
-#define S3C2410_GPE14_MASK     (0x03 << 28)
-
-#define S3C2410_GPE15_IICSDA   (0x02 << 30)
-#define S3C2410_GPE15_MASK     (0x03 << 30)
-
-#define S3C2440_GPE0_ACSYNC    (0x03 << 0)
-#define S3C2440_GPE1_ACBITCLK  (0x03 << 2)
-#define S3C2440_GPE2_ACRESET   (0x03 << 4)
-#define S3C2440_GPE3_ACIN      (0x03 << 6)
-#define S3C2440_GPE4_ACOUT     (0x03 << 8)
-
-#define S3C2410_GPE_PUPDIS(x)  (1<<(x))
-
-/* S3C2410:
- * Port F consists of 8 GPIO/Special function
- *
- * GPIO / interrupt inputs
- *
- * GPFCON has 2 bits for each of the input pins on port F
- *   00 = 0 input, 1 output, 2 interrupt (EINT0..7), 3 undefined
- *
- * pull up works like all other ports.
- *
- * GPIO/serial/misc pins
-*/
-
-#define S3C2410_GPFCON	   S3C2410_GPIOREG(0x50)
-#define S3C2410_GPFDAT	   S3C2410_GPIOREG(0x54)
-#define S3C2410_GPFUP	   S3C2410_GPIOREG(0x58)
-
-#define S3C2410_GPF0_EINT0  (0x02 << 0)
-#define S3C2410_GPF1_EINT1  (0x02 << 2)
-#define S3C2410_GPF2_EINT2  (0x02 << 4)
-#define S3C2410_GPF3_EINT3  (0x02 << 6)
-#define S3C2410_GPF4_EINT4  (0x02 << 8)
-#define S3C2410_GPF5_EINT5  (0x02 << 10)
-#define S3C2410_GPF6_EINT6  (0x02 << 12)
-#define S3C2410_GPF7_EINT7  (0x02 << 14)
-#define S3C2410_GPF_PUPDIS(x)  (1<<(x))
-
-/* S3C2410:
- * Port G consists of 8 GPIO/IRQ/Special function
- *
- * GPGCON has 2 bits for each of the input pins on port G
- *   00 = 0 input, 1 output, 2 interrupt (EINT0..7), 3 special func
- *
- * pull up works like all other ports.
-*/
-
-#define S3C2410_GPGCON	   S3C2410_GPIOREG(0x60)
-#define S3C2410_GPGDAT	   S3C2410_GPIOREG(0x64)
-#define S3C2410_GPGUP	   S3C2410_GPIOREG(0x68)
-
-#define S3C2410_GPG0_EINT8    (0x02 << 0)
-
-#define S3C2410_GPG1_EINT9    (0x02 << 2)
-
-#define S3C2410_GPG2_EINT10   (0x02 << 4)
-#define S3C2410_GPG2_nSS0     (0x03 << 4)
-
-#define S3C2410_GPG3_EINT11   (0x02 << 6)
-#define S3C2410_GPG3_nSS1     (0x03 << 6)
-
-#define S3C2410_GPG4_EINT12   (0x02 << 8)
-#define S3C2410_GPG4_LCDPWREN (0x03 << 8)
-#define S3C2443_GPG4_LCDPWRDN (0x03 << 8)
-
-#define S3C2410_GPG5_EINT13   (0x02 << 10)
-#define S3C2410_GPG5_SPIMISO1 (0x03 << 10)	/* not s3c2443 */
-
-#define S3C2410_GPG6_EINT14   (0x02 << 12)
-#define S3C2410_GPG6_SPIMOSI1 (0x03 << 12)
-
-#define S3C2410_GPG7_EINT15   (0x02 << 14)
-#define S3C2410_GPG7_SPICLK1  (0x03 << 14)
-
-#define S3C2410_GPG8_EINT16   (0x02 << 16)
-
-#define S3C2410_GPG9_EINT17   (0x02 << 18)
-
-#define S3C2410_GPG10_EINT18  (0x02 << 20)
-
-#define S3C2410_GPG11_EINT19  (0x02 << 22)
-#define S3C2410_GPG11_TCLK1   (0x03 << 22)
-#define S3C2443_GPG11_CF_nIREQ (0x03 << 22)
-
-#define S3C2410_GPG12_EINT20  (0x02 << 24)
-#define S3C2410_GPG12_XMON    (0x03 << 24)
-#define S3C2442_GPG12_nSPICS0 (0x03 << 24)
-#define S3C2443_GPG12_nINPACK (0x03 << 24)
-
-#define S3C2410_GPG13_EINT21  (0x02 << 26)
-#define S3C2410_GPG13_nXPON   (0x03 << 26)
-#define S3C2443_GPG13_CF_nREG (0x03 << 26)
-
-#define S3C2410_GPG14_EINT22  (0x02 << 28)
-#define S3C2410_GPG14_YMON    (0x03 << 28)
-#define S3C2443_GPG14_CF_RESET (0x03 << 28)
-
-#define S3C2410_GPG15_EINT23  (0x02 << 30)
-#define S3C2410_GPG15_nYPON   (0x03 << 30)
-#define S3C2443_GPG15_CF_PWR  (0x03 << 30)
-
-#define S3C2410_GPG_PUPDIS(x)  (1<<(x))
-
-/* Port H consists of11 GPIO/serial/Misc pins
- *
- * GPHCON has 2 bits for each of the input pins on port H
- *   00 = 0 input, 1 output, 2 interrupt (EINT0..7), 3 special func
- *
- * pull up works like all other ports.
-*/
-
-#define S3C2410_GPHCON	   S3C2410_GPIOREG(0x70)
-#define S3C2410_GPHDAT	   S3C2410_GPIOREG(0x74)
-#define S3C2410_GPHUP	   S3C2410_GPIOREG(0x78)
-
-#define S3C2410_GPH0_nCTS0  (0x02 << 0)
-#define S3C2416_GPH0_TXD0  (0x02 << 0)
-
-#define S3C2410_GPH1_nRTS0  (0x02 << 2)
-#define S3C2416_GPH1_RXD0  (0x02 << 2)
-
-#define S3C2410_GPH2_TXD0   (0x02 << 4)
-#define S3C2416_GPH2_TXD1   (0x02 << 4)
-
-#define S3C2410_GPH3_RXD0   (0x02 << 6)
-#define S3C2416_GPH3_RXD1   (0x02 << 6)
-
-#define S3C2410_GPH4_TXD1   (0x02 << 8)
-#define S3C2416_GPH4_TXD2   (0x02 << 8)
-
-#define S3C2410_GPH5_RXD1   (0x02 << 10)
-#define S3C2416_GPH5_RXD2   (0x02 << 10)
-
-#define S3C2410_GPH6_TXD2   (0x02 << 12)
-#define S3C2416_GPH6_TXD3   (0x02 << 12)
-#define S3C2410_GPH6_nRTS1  (0x03 << 12)
-#define S3C2416_GPH6_nRTS2  (0x03 << 12)
-
-#define S3C2410_GPH7_RXD2   (0x02 << 14)
-#define S3C2416_GPH7_RXD3   (0x02 << 14)
-#define S3C2410_GPH7_nCTS1  (0x03 << 14)
-#define S3C2416_GPH7_nCTS2  (0x03 << 14)
-
-#define S3C2410_GPH8_UCLK   (0x02 << 16)
-#define S3C2416_GPH8_nCTS0  (0x02 << 16)
-
-#define S3C2410_GPH9_CLKOUT0  (0x02 << 18)
-#define S3C2442_GPH9_nSPICS0  (0x03 << 18)
-#define S3C2416_GPH9_nRTS0    (0x02 << 18)
-
-#define S3C2410_GPH10_CLKOUT1 (0x02 << 20)
-#define S3C2416_GPH10_nCTS1   (0x02 << 20)
-
-#define S3C2416_GPH11_nRTS1   (0x02 << 22)
-
-#define S3C2416_GPH12_EXTUARTCLK (0x02 << 24)
-
-#define S3C2416_GPH13_CLKOUT0 (0x02 << 26)
-
-#define S3C2416_GPH14_CLKOUT1 (0x02 << 28)
-
-/* The S3C2412 and S3C2413 move the GPJ register set to after
- * GPH, which means all registers after 0x80 are now offset by 0x10
- * for the 2412/2413 from the 2410/2440/2442
-*/
-
-/*
- * Port J consists of 13 GPIO/Camera pins. GPJCON has 2 bits
- * for each of the pins on port J.
- *   00 - input, 01 output, 10 - camera
- *
- * Pull up works like all other ports.
- */
-
-#define S3C2413_GPJCON	   S3C2410_GPIOREG(0x80)
-#define S3C2413_GPJDAT	   S3C2410_GPIOREG(0x84)
-#define S3C2413_GPJUP	   S3C2410_GPIOREG(0x88)
-#define S3C2413_GPJSLPCON  S3C2410_GPIOREG(0x8C)
-
-/* S3C2443 and above */
-#define S3C2440_GPJCON	   S3C2410_GPIOREG(0xD0)
-#define S3C2440_GPJDAT	   S3C2410_GPIOREG(0xD4)
-#define S3C2440_GPJUP	   S3C2410_GPIOREG(0xD8)
-
-#define S3C2443_GPKCON	   S3C2410_GPIOREG(0xE0)
-#define S3C2443_GPKDAT	   S3C2410_GPIOREG(0xE4)
-#define S3C2443_GPKUP	   S3C2410_GPIOREG(0xE8)
-
-#define S3C2443_GPLCON	   S3C2410_GPIOREG(0xF0)
-#define S3C2443_GPLDAT	   S3C2410_GPIOREG(0xF4)
-#define S3C2443_GPLUP	   S3C2410_GPIOREG(0xF8)
-
-#define S3C2443_GPMCON	   S3C2410_GPIOREG(0x100)
-#define S3C2443_GPMDAT	   S3C2410_GPIOREG(0x104)
-#define S3C2443_GPMUP	   S3C2410_GPIOREG(0x108)
-
-/* miscellaneous control */
-#define S3C2410_MISCCR	   S3C2410_GPIOREG(0x80)
-
-/* see clock.h for dclk definitions */
-
-/* pullup control on databus */
-#define S3C2410_MISCCR_SPUCR_HEN    (0<<0)
-#define S3C2410_MISCCR_SPUCR_HDIS   (1<<0)
-#define S3C2410_MISCCR_SPUCR_LEN    (0<<1)
-#define S3C2410_MISCCR_SPUCR_LDIS   (1<<1)
-
-#define S3C2410_MISCCR_USBDEV	    (0<<3)
-#define S3C2410_MISCCR_USBHOST	    (1<<3)
-
-#define S3C2410_MISCCR_CLK0_MPLL    (0<<4)
-#define S3C2410_MISCCR_CLK0_UPLL    (1<<4)
-#define S3C2410_MISCCR_CLK0_FCLK    (2<<4)
-#define S3C2410_MISCCR_CLK0_HCLK    (3<<4)
-#define S3C2410_MISCCR_CLK0_PCLK    (4<<4)
-#define S3C2410_MISCCR_CLK0_DCLK0   (5<<4)
-#define S3C2410_MISCCR_CLK0_MASK    (7<<4)
-
-#define S3C2412_MISCCR_CLK0_RTC	    (2<<4)
-
-#define S3C2410_MISCCR_CLK1_MPLL    (0<<8)
-#define S3C2410_MISCCR_CLK1_UPLL    (1<<8)
-#define S3C2410_MISCCR_CLK1_FCLK    (2<<8)
-#define S3C2410_MISCCR_CLK1_HCLK    (3<<8)
-#define S3C2410_MISCCR_CLK1_PCLK    (4<<8)
-#define S3C2410_MISCCR_CLK1_DCLK1   (5<<8)
-#define S3C2410_MISCCR_CLK1_MASK    (7<<8)
-
-#define S3C2412_MISCCR_CLK1_CLKsrc  (0<<8)
-
-#define S3C2410_MISCCR_USBSUSPND0   (1<<12)
-#define S3C2416_MISCCR_SEL_SUSPND   (1<<12)
-#define S3C2410_MISCCR_USBSUSPND1   (1<<13)
-
-#define S3C2410_MISCCR_nRSTCON	    (1<<16)
-
-#define S3C2410_MISCCR_nEN_SCLK0    (1<<17)
-#define S3C2410_MISCCR_nEN_SCLK1    (1<<18)
-#define S3C2410_MISCCR_nEN_SCLKE    (1<<19)	/* not 2412 */
-#define S3C2410_MISCCR_SDSLEEP	    (7<<17)
-
-#define S3C2416_MISCCR_FLT_I2C      (1<<24)
-#define S3C2416_MISCCR_HSSPI_EN2    (1<<31)
-
-/* external interrupt control... */
-/* S3C2410_EXTINT0 -> irq sense control for EINT0..EINT7
- * S3C2410_EXTINT1 -> irq sense control for EINT8..EINT15
- * S3C2410_EXTINT2 -> irq sense control for EINT16..EINT23
- *
- * note S3C2410_EXTINT2 has filtering options for EINT16..EINT23
- *
- * Samsung datasheet p9-25
-*/
-#define S3C2410_EXTINT0	   S3C2410_GPIOREG(0x88)
-#define S3C2410_EXTINT1	   S3C2410_GPIOREG(0x8C)
-#define S3C2410_EXTINT2	   S3C2410_GPIOREG(0x90)
-
-#define S3C24XX_EXTINT0	   S3C24XX_GPIOREG2(0x88)
-#define S3C24XX_EXTINT1	   S3C24XX_GPIOREG2(0x8C)
-#define S3C24XX_EXTINT2	   S3C24XX_GPIOREG2(0x90)
-
-/* interrupt filtering control for EINT16..EINT23 */
-#define S3C2410_EINFLT0	   S3C2410_GPIOREG(0x94)
-#define S3C2410_EINFLT1	   S3C2410_GPIOREG(0x98)
-#define S3C2410_EINFLT2	   S3C2410_GPIOREG(0x9C)
-#define S3C2410_EINFLT3	   S3C2410_GPIOREG(0xA0)
-
-#define S3C24XX_EINFLT0	   S3C24XX_GPIOREG2(0x94)
-#define S3C24XX_EINFLT1	   S3C24XX_GPIOREG2(0x98)
-#define S3C24XX_EINFLT2	   S3C24XX_GPIOREG2(0x9C)
-#define S3C24XX_EINFLT3	   S3C24XX_GPIOREG2(0xA0)
-
-/* values for interrupt filtering */
-#define S3C2410_EINTFLT_PCLK		(0x00)
-#define S3C2410_EINTFLT_EXTCLK		(1<<7)
-#define S3C2410_EINTFLT_WIDTHMSK(x)	((x) & 0x3f)
-
-/* removed EINTxxxx defs from here, not meant for this */
-
-/* GSTATUS have miscellaneous information in them
- *
- * These move between s3c2410 and s3c2412 style systems.
- */
-
-#define S3C2410_GSTATUS0   S3C2410_GPIOREG(0x0AC)
-#define S3C2410_GSTATUS1   S3C2410_GPIOREG(0x0B0)
-#define S3C2410_GSTATUS2   S3C2410_GPIOREG(0x0B4)
-#define S3C2410_GSTATUS3   S3C2410_GPIOREG(0x0B8)
-#define S3C2410_GSTATUS4   S3C2410_GPIOREG(0x0BC)
-
-#define S3C2412_GSTATUS0   S3C2410_GPIOREG(0x0BC)
-#define S3C2412_GSTATUS1   S3C2410_GPIOREG(0x0C0)
-#define S3C2412_GSTATUS2   S3C2410_GPIOREG(0x0C4)
-#define S3C2412_GSTATUS3   S3C2410_GPIOREG(0x0C8)
-#define S3C2412_GSTATUS4   S3C2410_GPIOREG(0x0CC)
-
-#define S3C24XX_GSTATUS0   S3C24XX_GPIOREG2(0x0AC)
-#define S3C24XX_GSTATUS1   S3C24XX_GPIOREG2(0x0B0)
-#define S3C24XX_GSTATUS2   S3C24XX_GPIOREG2(0x0B4)
-#define S3C24XX_GSTATUS3   S3C24XX_GPIOREG2(0x0B8)
-#define S3C24XX_GSTATUS4   S3C24XX_GPIOREG2(0x0BC)
-
-#define S3C2410_GSTATUS0_nWAIT	   (1<<3)
-#define S3C2410_GSTATUS0_NCON	   (1<<2)
-#define S3C2410_GSTATUS0_RnB	   (1<<1)
-#define S3C2410_GSTATUS0_nBATTFLT  (1<<0)
-
-#define S3C2410_GSTATUS1_IDMASK	   (0xffff0000)
-#define S3C2410_GSTATUS1_2410	   (0x32410000)
-#define S3C2410_GSTATUS1_2412	   (0x32412001)
-#define S3C2410_GSTATUS1_2416	   (0x32416003)
-#define S3C2410_GSTATUS1_2440	   (0x32440000)
-#define S3C2410_GSTATUS1_2442	   (0x32440aaa)
-/* some 2416 CPUs report this value also */
-#define S3C2410_GSTATUS1_2450	   (0x32450003)
-
-#define S3C2410_GSTATUS2_WTRESET   (1<<2)
-#define S3C2410_GSTATUS2_OFFRESET  (1<<1)
-#define S3C2410_GSTATUS2_PONRESET  (1<<0)
-
-/* 2412/2413 sleep configuration registers */
-
-#define S3C2412_GPBSLPCON	S3C2410_GPIOREG(0x1C)
-#define S3C2412_GPCSLPCON	S3C2410_GPIOREG(0x2C)
-#define S3C2412_GPDSLPCON	S3C2410_GPIOREG(0x3C)
-#define S3C2412_GPFSLPCON	S3C2410_GPIOREG(0x5C)
-#define S3C2412_GPGSLPCON	S3C2410_GPIOREG(0x6C)
-#define S3C2412_GPHSLPCON	S3C2410_GPIOREG(0x7C)
-
-/* definitions for each pin bit */
-#define S3C2412_GPIO_SLPCON_LOW	 ( 0x00 )
-#define S3C2412_GPIO_SLPCON_HIGH ( 0x01 )
-#define S3C2412_GPIO_SLPCON_IN   ( 0x02 )
-#define S3C2412_GPIO_SLPCON_PULL ( 0x03 )
-
-#define S3C2412_SLPCON_LOW(x)	( 0x00 << ((x) * 2))
-#define S3C2412_SLPCON_HIGH(x)	( 0x01 << ((x) * 2))
-#define S3C2412_SLPCON_IN(x)	( 0x02 << ((x) * 2))
-#define S3C2412_SLPCON_PULL(x)	( 0x03 << ((x) * 2))
-#define S3C2412_SLPCON_EINT(x)	( 0x02 << ((x) * 2))  /* only IRQ pins */
-#define S3C2412_SLPCON_MASK(x)	( 0x03 << ((x) * 2))
-
-#define S3C2412_SLPCON_ALL_LOW	(0x0)
-#define S3C2412_SLPCON_ALL_HIGH	(0x11111111 | 0x44444444)
-#define S3C2412_SLPCON_ALL_IN  	(0x22222222 | 0x88888888)
-#define S3C2412_SLPCON_ALL_PULL	(0x33333333)
-
-#endif	/* __ASM_ARCH_REGS_GPIO_H */
-
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-irq.h b/arch/arm/mach-s3c24xx/include/mach/regs-irq.h
deleted file mode 100644
index 2921b48c56b2..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/regs-irq.h
+++ /dev/null
@@ -1,51 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2003 Simtec Electronics <linux@simtec.co.uk>
- *		      http://www.simtec.co.uk/products/SWLINUX/
- */
-
-
-#ifndef ___ASM_ARCH_REGS_IRQ_H
-#define ___ASM_ARCH_REGS_IRQ_H
-
-#include <plat/map-s3c.h>
-
-/* interrupt controller */
-
-#define S3C2410_IRQREG(x)   ((x) + S3C24XX_VA_IRQ)
-#define S3C2410_EINTREG(x)  ((x) + S3C24XX_VA_GPIO)
-#define S3C24XX_EINTREG(x)  ((x) + S3C24XX_VA_GPIO2)
-
-#define S3C2410_SRCPND	       S3C2410_IRQREG(0x000)
-#define S3C2410_INTMOD	       S3C2410_IRQREG(0x004)
-#define S3C2410_INTMSK	       S3C2410_IRQREG(0x008)
-#define S3C2410_PRIORITY       S3C2410_IRQREG(0x00C)
-#define S3C2410_INTPND	       S3C2410_IRQREG(0x010)
-#define S3C2410_INTOFFSET      S3C2410_IRQREG(0x014)
-#define S3C2410_SUBSRCPND      S3C2410_IRQREG(0x018)
-#define S3C2410_INTSUBMSK      S3C2410_IRQREG(0x01C)
-
-#define S3C2416_PRIORITY_MODE1		S3C2410_IRQREG(0x030)
-#define S3C2416_PRIORITY_UPDATE1	S3C2410_IRQREG(0x034)
-#define S3C2416_SRCPND2			S3C2410_IRQREG(0x040)
-#define S3C2416_INTMOD2			S3C2410_IRQREG(0x044)
-#define S3C2416_INTMSK2			S3C2410_IRQREG(0x048)
-#define S3C2416_INTPND2			S3C2410_IRQREG(0x050)
-#define S3C2416_INTOFFSET2		S3C2410_IRQREG(0x054)
-#define S3C2416_PRIORITY_MODE2		S3C2410_IRQREG(0x070)
-#define S3C2416_PRIORITY_UPDATE2	S3C2410_IRQREG(0x074)
-
-/* mask: 0=enable, 1=disable
- * 1 bit EINT, 4=EINT4, 23=EINT23
- * EINT0,1,2,3 are not handled here.
-*/
-
-#define S3C2410_EINTMASK       S3C2410_EINTREG(0x0A4)
-#define S3C2410_EINTPEND       S3C2410_EINTREG(0X0A8)
-#define S3C2412_EINTMASK       S3C2410_EINTREG(0x0B4)
-#define S3C2412_EINTPEND       S3C2410_EINTREG(0X0B8)
-
-#define S3C24XX_EINTMASK       S3C24XX_EINTREG(0x0A4)
-#define S3C24XX_EINTPEND       S3C24XX_EINTREG(0X0A8)
-
-#endif /* ___ASM_ARCH_REGS_IRQ_H */
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-s3c2443-clock.h b/arch/arm/mach-s3c24xx/include/mach/regs-s3c2443-clock.h
deleted file mode 100644
index fefef7233f4b..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/regs-s3c2443-clock.h
+++ /dev/null
@@ -1,238 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2007 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *	http://armlinux.simtec.co.uk/
- *
- * S3C2443 clock register definitions
- */
-
-#ifndef __ASM_ARM_REGS_S3C2443_CLOCK
-#define __ASM_ARM_REGS_S3C2443_CLOCK
-
-#include <linux/delay.h>
-#include <plat/map-s3c.h>
-
-#define S3C2443_CLKREG(x)		((x) + S3C24XX_VA_CLKPWR)
-
-#define S3C2443_PLLCON_MDIVSHIFT	16
-#define S3C2443_PLLCON_PDIVSHIFT	8
-#define S3C2443_PLLCON_SDIVSHIFT	0
-#define S3C2443_PLLCON_MDIVMASK		((1<<(1+(23-16)))-1)
-#define S3C2443_PLLCON_PDIVMASK		((1<<(1+(9-8)))-1)
-#define S3C2443_PLLCON_SDIVMASK		(3)
-
-#define S3C2443_MPLLCON			S3C2443_CLKREG(0x10)
-#define S3C2443_EPLLCON			S3C2443_CLKREG(0x18)
-#define S3C2443_CLKSRC			S3C2443_CLKREG(0x20)
-#define S3C2443_CLKDIV0			S3C2443_CLKREG(0x24)
-#define S3C2443_CLKDIV1			S3C2443_CLKREG(0x28)
-#define S3C2443_HCLKCON			S3C2443_CLKREG(0x30)
-#define S3C2443_PCLKCON			S3C2443_CLKREG(0x34)
-#define S3C2443_SCLKCON			S3C2443_CLKREG(0x38)
-#define S3C2443_PWRMODE			S3C2443_CLKREG(0x40)
-#define S3C2443_SWRST			S3C2443_CLKREG(0x44)
-#define S3C2443_BUSPRI0			S3C2443_CLKREG(0x50)
-#define S3C2443_SYSID			S3C2443_CLKREG(0x5C)
-#define S3C2443_PWRCFG			S3C2443_CLKREG(0x60)
-#define S3C2443_RSTCON			S3C2443_CLKREG(0x64)
-#define S3C2443_PHYCTRL			S3C2443_CLKREG(0x80)
-#define S3C2443_PHYPWR			S3C2443_CLKREG(0x84)
-#define S3C2443_URSTCON			S3C2443_CLKREG(0x88)
-#define S3C2443_UCLKCON			S3C2443_CLKREG(0x8C)
-
-#define S3C2443_PLLCON_OFF		(1<<24)
-
-#define S3C2443_CLKSRC_EPLLREF_XTAL	(2<<7)
-#define S3C2443_CLKSRC_EPLLREF_EXTCLK	(3<<7)
-#define S3C2443_CLKSRC_EPLLREF_MPLLREF	(0<<7)
-#define S3C2443_CLKSRC_EPLLREF_MPLLREF2	(1<<7)
-#define S3C2443_CLKSRC_EPLLREF_MASK	(3<<7)
-
-#define S3C2443_CLKSRC_EXTCLK_DIV	(1<<3)
-
-#define S3C2443_CLKDIV0_HALF_HCLK	(1<<3)
-#define S3C2443_CLKDIV0_HALF_PCLK	(1<<2)
-
-#define S3C2443_CLKDIV0_HCLKDIV_MASK	(3<<0)
-
-#define S3C2443_CLKDIV0_EXTDIV_MASK	(3<<6)
-#define S3C2443_CLKDIV0_EXTDIV_SHIFT	(6)
-
-#define S3C2443_CLKDIV0_PREDIV_MASK	(3<<4)
-#define S3C2443_CLKDIV0_PREDIV_SHIFT	(4)
-
-#define S3C2416_CLKDIV0_ARMDIV_MASK	(7 << 9)
-#define S3C2443_CLKDIV0_ARMDIV_MASK	(15<<9)
-#define S3C2443_CLKDIV0_ARMDIV_SHIFT	(9)
-#define S3C2443_CLKDIV0_ARMDIV_1	(0<<9)
-#define S3C2443_CLKDIV0_ARMDIV_2	(8<<9)
-#define S3C2443_CLKDIV0_ARMDIV_3	(2<<9)
-#define S3C2443_CLKDIV0_ARMDIV_4	(9<<9)
-#define S3C2443_CLKDIV0_ARMDIV_6	(10<<9)
-#define S3C2443_CLKDIV0_ARMDIV_8	(11<<9)
-#define S3C2443_CLKDIV0_ARMDIV_12	(13<<9)
-#define S3C2443_CLKDIV0_ARMDIV_16	(15<<9)
-
-/* S3C2443_CLKDIV1 removed, only used in clock.c code */
-
-#define S3C2443_CLKCON_NAND
-
-#define S3C2443_HCLKCON_DMA0		(1<<0)
-#define S3C2443_HCLKCON_DMA1		(1<<1)
-#define S3C2443_HCLKCON_DMA2		(1<<2)
-#define S3C2443_HCLKCON_DMA3		(1<<3)
-#define S3C2443_HCLKCON_DMA4		(1<<4)
-#define S3C2443_HCLKCON_DMA5		(1<<5)
-#define S3C2443_HCLKCON_CAMIF		(1<<8)
-#define S3C2443_HCLKCON_LCDC		(1<<9)
-#define S3C2443_HCLKCON_USBH		(1<<11)
-#define S3C2443_HCLKCON_USBD		(1<<12)
-#define S3C2416_HCLKCON_HSMMC0		(1<<15)
-#define S3C2443_HCLKCON_HSMMC		(1<<16)
-#define S3C2443_HCLKCON_CFC		(1<<17)
-#define S3C2443_HCLKCON_SSMC		(1<<18)
-#define S3C2443_HCLKCON_DRAMC		(1<<19)
-
-#define S3C2443_PCLKCON_UART0		(1<<0)
-#define S3C2443_PCLKCON_UART1		(1<<1)
-#define S3C2443_PCLKCON_UART2		(1<<2)
-#define S3C2443_PCLKCON_UART3		(1<<3)
-#define S3C2443_PCLKCON_IIC		(1<<4)
-#define S3C2443_PCLKCON_SDI		(1<<5)
-#define S3C2443_PCLKCON_HSSPI		(1<<6)
-#define S3C2443_PCLKCON_ADC		(1<<7)
-#define S3C2443_PCLKCON_AC97		(1<<8)
-#define S3C2443_PCLKCON_IIS		(1<<9)
-#define S3C2443_PCLKCON_PWMT		(1<<10)
-#define S3C2443_PCLKCON_WDT		(1<<11)
-#define S3C2443_PCLKCON_RTC		(1<<12)
-#define S3C2443_PCLKCON_GPIO		(1<<13)
-#define S3C2443_PCLKCON_SPI0		(1<<14)
-#define S3C2443_PCLKCON_SPI1		(1<<15)
-
-#define S3C2443_SCLKCON_DDRCLK		(1<<16)
-#define S3C2443_SCLKCON_SSMCCLK		(1<<15)
-#define S3C2443_SCLKCON_HSSPICLK	(1<<14)
-#define S3C2443_SCLKCON_HSMMCCLK_EXT	(1<<13)
-#define S3C2443_SCLKCON_HSMMCCLK_EPLL	(1<<12)
-#define S3C2443_SCLKCON_CAMCLK		(1<<11)
-#define S3C2443_SCLKCON_DISPCLK		(1<<10)
-#define S3C2443_SCLKCON_I2SCLK		(1<<9)
-#define S3C2443_SCLKCON_UARTCLK		(1<<8)
-#define S3C2443_SCLKCON_USBHOST		(1<<1)
-
-#define S3C2443_PWRCFG_SLEEP		(1<<15)
-
-#define S3C2443_PWRCFG_USBPHY		(1 << 4)
-
-#define S3C2443_URSTCON_FUNCRST		(1 << 2)
-#define S3C2443_URSTCON_PHYRST		(1 << 0)
-
-#define S3C2443_PHYCTRL_CLKSEL		(1 << 3)
-#define S3C2443_PHYCTRL_EXTCLK		(1 << 2)
-#define S3C2443_PHYCTRL_PLLSEL		(1 << 1)
-#define S3C2443_PHYCTRL_DSPORT		(1 << 0)
-
-#define S3C2443_PHYPWR_COMMON_ON	(1 << 31)
-#define S3C2443_PHYPWR_ANALOG_PD	(1 << 4)
-#define S3C2443_PHYPWR_PLL_REFCLK	(1 << 3)
-#define S3C2443_PHYPWR_XO_ON		(1 << 2)
-#define S3C2443_PHYPWR_PLL_PWRDN	(1 << 1)
-#define S3C2443_PHYPWR_FSUSPEND		(1 << 0)
-
-#define S3C2443_UCLKCON_DETECT_VBUS	(1 << 31)
-#define S3C2443_UCLKCON_FUNC_CLKEN	(1 << 2)
-#define S3C2443_UCLKCON_TCLKEN		(1 << 0)
-
-#include <asm/div64.h>
-
-static inline unsigned int
-s3c2443_get_mpll(unsigned int pllval, unsigned int baseclk)
-{
-	unsigned int mdiv, pdiv, sdiv;
-	uint64_t fvco;
-
-	mdiv = pllval >> S3C2443_PLLCON_MDIVSHIFT;
-	pdiv = pllval >> S3C2443_PLLCON_PDIVSHIFT;
-	sdiv = pllval >> S3C2443_PLLCON_SDIVSHIFT;
-
-	mdiv &= S3C2443_PLLCON_MDIVMASK;
-	pdiv &= S3C2443_PLLCON_PDIVMASK;
-	sdiv &= S3C2443_PLLCON_SDIVMASK;
-
-	fvco = (uint64_t)baseclk * (2 * (mdiv + 8));
-	do_div(fvco, pdiv << sdiv);
-
-	return (unsigned int)fvco;
-}
-
-static inline unsigned int
-s3c2443_get_epll(unsigned int pllval, unsigned int baseclk)
-{
-	unsigned int mdiv, pdiv, sdiv;
-	uint64_t fvco;
-
-	mdiv = pllval >> S3C2443_PLLCON_MDIVSHIFT;
-	pdiv = pllval >> S3C2443_PLLCON_PDIVSHIFT;
-	sdiv = pllval >> S3C2443_PLLCON_SDIVSHIFT;
-
-	mdiv &= S3C2443_PLLCON_MDIVMASK;
-	pdiv &= S3C2443_PLLCON_PDIVMASK;
-	sdiv &= S3C2443_PLLCON_SDIVMASK;
-
-	fvco = (uint64_t)baseclk * (mdiv + 8);
-	do_div(fvco, (pdiv + 2) << sdiv);
-
-	return (unsigned int)fvco;
-}
-
-static inline void s3c_hsudc_init_phy(void)
-{
-	u32 cfg;
-
-	cfg = readl(S3C2443_PWRCFG) | S3C2443_PWRCFG_USBPHY;
-	writel(cfg, S3C2443_PWRCFG);
-
-	cfg = readl(S3C2443_URSTCON);
-	cfg |= (S3C2443_URSTCON_FUNCRST | S3C2443_URSTCON_PHYRST);
-	writel(cfg, S3C2443_URSTCON);
-	mdelay(1);
-
-	cfg = readl(S3C2443_URSTCON);
-	cfg &= ~(S3C2443_URSTCON_FUNCRST | S3C2443_URSTCON_PHYRST);
-	writel(cfg, S3C2443_URSTCON);
-
-	cfg = readl(S3C2443_PHYCTRL);
-	cfg &= ~(S3C2443_PHYCTRL_CLKSEL | S3C2443_PHYCTRL_DSPORT);
-	cfg |= (S3C2443_PHYCTRL_EXTCLK | S3C2443_PHYCTRL_PLLSEL);
-	writel(cfg, S3C2443_PHYCTRL);
-
-	cfg = readl(S3C2443_PHYPWR);
-	cfg &= ~(S3C2443_PHYPWR_FSUSPEND | S3C2443_PHYPWR_PLL_PWRDN |
-		S3C2443_PHYPWR_XO_ON | S3C2443_PHYPWR_PLL_REFCLK |
-		S3C2443_PHYPWR_ANALOG_PD);
-	cfg |= S3C2443_PHYPWR_COMMON_ON;
-	writel(cfg, S3C2443_PHYPWR);
-
-	cfg = readl(S3C2443_UCLKCON);
-	cfg |= (S3C2443_UCLKCON_DETECT_VBUS | S3C2443_UCLKCON_FUNC_CLKEN |
-		S3C2443_UCLKCON_TCLKEN);
-	writel(cfg, S3C2443_UCLKCON);
-}
-
-static inline void s3c_hsudc_uninit_phy(void)
-{
-	u32 cfg;
-
-	cfg = readl(S3C2443_PWRCFG) & ~S3C2443_PWRCFG_USBPHY;
-	writel(cfg, S3C2443_PWRCFG);
-
-	writel(S3C2443_PHYPWR_FSUSPEND, S3C2443_PHYPWR);
-
-	cfg = readl(S3C2443_UCLKCON) & ~S3C2443_UCLKCON_FUNC_CLKEN;
-	writel(cfg, S3C2443_UCLKCON);
-}
-
-#endif /*  __ASM_ARM_REGS_S3C2443_CLOCK */
-
diff --git a/arch/arm/mach-s3c24xx/include/mach/rtc-core.h b/arch/arm/mach-s3c24xx/include/mach/rtc-core.h
deleted file mode 100644
index 88510333b96b..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/rtc-core.h
+++ /dev/null
@@ -1,23 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2011 Heiko Stuebner <heiko@sntech.de>
- *
- * Samsung RTC Controller core functions
- */
-
-#ifndef __RTC_CORE_H
-#define __RTC_CORE_H __FILE__
-
-/* These functions are only for use with the core support code, such as
- * the cpu specific initialisation code
- */
-
-extern struct platform_device s3c_device_rtc;
-
-/* re-define device name depending on support. */
-static inline void s3c_rtc_setname(char *name)
-{
-	s3c_device_rtc.name = name;
-}
-
-#endif /* __RTC_CORE_H */
diff --git a/arch/arm/mach-s3c24xx/include/mach/s3c2412.h b/arch/arm/mach-s3c24xx/include/mach/s3c2412.h
deleted file mode 100644
index 1ae369c81beb..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/s3c2412.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2008 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *	http://armlinux.simtec.co.uk/
- */
-
-#ifndef __ARCH_ARM_MACH_S3C24XX_S3C2412_H
-#define __ARCH_ARM_MACH_S3C24XX_S3C2412_H __FILE__
-
-#include <plat/map-s3c.h>
-
-#define S3C2412_MEMREG(x)		(S3C24XX_VA_MEMCTRL + (x))
-#define S3C2412_EBIREG(x)		(S3C2412_VA_EBI + (x))
-
-#define S3C2412_SSMCREG(x)		(S3C2412_VA_SSMC + (x))
-#define S3C2412_SSMC(x, o)		(S3C2412_SSMCREG((x * 0x20) + (o)))
-
-#define S3C2412_REFRESH			S3C2412_MEMREG(0x10)
-
-#define S3C2412_EBI_BANKCFG		S3C2412_EBIREG(0x4)
-
-#define S3C2412_SSMC_BANK(x)		S3C2412_SSMC(x, 0x0)
-
-#endif /* __ARCH_ARM_MACH_S3C24XX_S3C2412_H */