Merge tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull SoC DT updates from Arnd Bergmann:
 "About a quarter of the changes are for 32-bit arm, mostly filling in
  device support for existing machines and adding minor cleanups, mostly
  for Qualcomm and Samsung based machines.

  Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
  Rockchips that have been around for a while but were lacking kernel
  support so far: RV1126 is a Vision SoC with an NPU and is used in the
  Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
  for TV boxes and so far only comes with a dts for its refernece
  design.

  The other 32-bit boards that were added are two ASpeed AST2600 based
  BMC boards, the Microchip sam9x60_curiosity development board (Armv5
  based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
  for i.MX53 and i.MX6ULL.

  On the RISC-V side, there are fewer patches, but a total of ten new
  single-board computers based on variations of the Allwinner D1/T113
  chip, plus one more board based on Microchip Polarfire.

  As usual, arm64 has by far the most changes here, with over 700
  non-merge changesets, among them over 400 alone for Qualcomm. The
  newly added SoCs this time are all recent high-end embedded SoCs for
  various markets, each on comes with support for its reference board:

   - Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
   - Qualcomm QDU1000/QRU1000 5G RAN platform
   - Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
   - TI J784S4 for industrial and automotive applications

  In total, there are 46 new arm64 machines:
   - Reference platforms for each of the five new SoCs
   - Three Amlogic based development boards
   - Six embedded machines based on NXP i.MX8MM and i.MX8MP
   - The Mediatek mt7986a based Banana Pi R3 router
   - Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
     (Snapdragon 662) and SM8250 (Snapdragon 865)
   - Two LTE dongles, also based on MSM8916
   - Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
     SDM450 and SDM632
   - Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
   - Nine development boards based on Rockchips RK3588, RK3568, RK3566
     and RK3328.
   - Five development machines based on TI K3 (AM642/AM654/AM68/AM69)

  The cleanup of dtc warnings continues across all platforms, adding to
  the total number of changes"

* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
  dt-bindings: riscv: correct starfive visionfive 2 compatibles
  ARM: dts: socfpga: Add enclustra PE1 devicetree
  dt-bindings: altera: Add enclustra mercury PE1
  arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
  arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
  arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
  arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
  arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
  arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
  arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
  arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
  arm64: dts: qcom: pmk8350: Use the correct PON compatible
  arm64: dts: qcom: sc8280xp-x13s: Enable external display
  arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
  arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
  arm64: dts: qcom: sm8350-hdk: enable GPU
  arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
  arm64: dts: qcom: sm8350: finish reordering nodes
  arm64: dts: qcom: sm8350: move more nodes to correct place
  arm64: dts: qcom: sm8350: reorder device nodes
  ...

1 files changed, 120 insertions, 0 deletions

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 9b83925893b7..4f18b4a9a8c8 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -5,6 +5,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/pinctrl/mt65xx.h>
+
 #include "mt7986a.dtsi"
 
 / {
@@ -23,6 +25,24 @@
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &crypto {
@@ -58,7 +78,99 @@
 	};
 };
 
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
 &pio {
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_wake", "pcie_pereset";
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
@@ -140,6 +252,10 @@
 	status = "okay";
 };
 
+&ssusb {
+	status = "okay";
+};
+
 &switch {
 	ports {
 		#address-cells = <1>;
@@ -201,6 +317,10 @@
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";