Merge tag 'qcom-arm64-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt

Qualcomm ARM64 Updates for v5.3

* Switch to use second gen PON on PM8998
* Add PSCI cupidle states for MSM8996, MSM8998,and SDM845
* Add MSM8996 UFS phy reset controller
* Add propre cpu capacity scaling on MSM8996
* Fixups for APR domain, legacy clocks, and PSCI entry latency on MSM8996
* Enable SMMUs on MSM8996
* Add Dragonboard 845C
* Add Q6V5, GPU, GMU, and AOSS QMP node on SDM845
* Fixup CPU topology on SDM845
* Change USB1 to be peripheral on SDM845 MTP
* Add PCIe Phy, RC nodes, ANOC1 SMMU, and RPMPD node on MSM8998
* Update coresight bindings for MSM8916
* Update idle state names and entry-method on MSM8916
* Add PCIe, RPMPD, LPASS, Q6, TCSR, TuringCC, PSCI cpuidle states,
  and CDSP on QCS404
* Add reset-cells property to QCS404 GCC node
* Fixup s3 max voltage, l3 min voltage, drive strength typo, and
  s3 supply definition on QCS404-evb
* Fixup ADC outputs and VADC calibration on PMS405

* tag 'qcom-arm64-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (39 commits)
  arm64: dts: qcom: qcs404-evb: fix vdd_apc supply
  arm64: dts: qcom: pm8998: Use qcom,pm8998-pon binding for second gen pon
  arm64: dts: qcom: msm8996: Enable SMMUs
  arm64: dts: qcom: msm8996: Correct apr-domain property
  arm64: dts: qcom: Add Dragonboard 845c
  arm64: dts: qcom: qcs404-evb: Enable PCIe
  arm64: dts: qcom: qcs404: Add PCIe related nodes
  arm64: dts: qcom: msm8998: Add PCIe PHY and RC nodes
  arm64: dts: qcom: msm8998: Add ANOC1 SMMU node
  arm64: dts: qcom: msm8996: Stop using legacy clock names
  arm64: dts: msm8996: fix PSCI entry-latency-us
  arm64: dts: qcom: msm8998: Add PSCI cpuidle low power states
  arm64: dts: qcom: sdm845: Add Q6V5 MSS node
  arm64: dts: qcom: Add AOSS QMP node
  arm64: dts: qcom-qcs404: Add reset-cells to GCC node
  arm64: dts: qcom-msm8916: Update coresight DT bindings
  arm64: dts: qcom: msm8998: Add rpmpd node
  arm64: dts: qcom: qcs404: Add rpmpd node
  arm64: dts: qcom: qcs404: Move lpass and q6 into soc
  arm64: dts: qcom: qcs404: Fully describe the CDSP
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

11 files changed, 1392 insertions, 142 deletions

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 21d548f02d39..b3fe72ff2955 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8992-bullhead-rev-101.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8994-angler-rev-101.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index dacd465fc62e..5ea9fb8f2f87 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -102,7 +102,7 @@
 			reg = <0x0>;
 			next-level-cache = <&L2_0>;
 			enable-method = "psci";
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
 			clocks = <&apcs>;
 			operating-points-v2 = <&cpu_opp_table>;
 			#cooling-cells = <2>;
@@ -114,7 +114,7 @@
 			reg = <0x1>;
 			next-level-cache = <&L2_0>;
 			enable-method = "psci";
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
 			clocks = <&apcs>;
 			operating-points-v2 = <&cpu_opp_table>;
 			#cooling-cells = <2>;
@@ -126,7 +126,7 @@
 			reg = <0x2>;
 			next-level-cache = <&L2_0>;
 			enable-method = "psci";
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
 			clocks = <&apcs>;
 			operating-points-v2 = <&cpu_opp_table>;
 			#cooling-cells = <2>;
@@ -138,7 +138,7 @@
 			reg = <0x3>;
 			next-level-cache = <&L2_0>;
 			enable-method = "psci";
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
 			clocks = <&apcs>;
 			operating-points-v2 = <&cpu_opp_table>;
 			#cooling-cells = <2>;
@@ -150,8 +150,11 @@
 		};
 
 		idle-states {
-			CPU_SPC: spc {
+			entry-method = "psci";
+
+			CPU_SLEEP_0: cpu-sleep-0 {
 				compatible = "arm,idle-state";
+				idle-state-name = "standalone-power-collapse";
 				arm,psci-suspend-param = <0x40000002>;
 				entry-latency-us = <130>;
 				exit-latency-us = <150>;
@@ -1164,7 +1167,7 @@
 		};
 
 		funnel@821000 {
-			compatible = "arm,coresight-funnel", "arm,primecell";
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
 			reg = <0x821000 0x1000>;
 
 			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
@@ -1277,7 +1280,7 @@
 		};
 
 		funnel@841000 {	/* APSS funnel only 4 inputs are used */
-			compatible = "arm,coresight-funnel", "arm,primecell";
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
 			reg = <0x841000 0x1000>;
 
 			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 942465d8aeb7..96c0a481f454 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -94,6 +94,8 @@
 			compatible = "qcom,kryo";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			capacity-dmips-mhz = <1024>;
 			next-level-cache = <&L2_0>;
 			L2_0: l2-cache {
 			      compatible = "cache";
@@ -106,6 +108,8 @@
 			compatible = "qcom,kryo";
 			reg = <0x0 0x1>;
 			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			capacity-dmips-mhz = <1024>;
 			next-level-cache = <&L2_0>;
 		};
 
@@ -114,6 +118,8 @@
 			compatible = "qcom,kryo";
 			reg = <0x0 0x100>;
 			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			capacity-dmips-mhz = <1024>;
 			next-level-cache = <&L2_1>;
 			L2_1: l2-cache {
 			      compatible = "cache";
@@ -126,6 +132,8 @@
 			compatible = "qcom,kryo";
 			reg = <0x0 0x101>;
 			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			capacity-dmips-mhz = <1024>;
 			next-level-cache = <&L2_1>;
 		};
 
@@ -150,6 +158,19 @@
 				};
 			};
 		};
+
+		idle-states {
+			entry-method = "psci";
+
+			CPU_SLEEP_0: cpu-sleep-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "standalone-power-collapse";
+				arm,psci-suspend-param = <0x00000004>;
+				entry-latency-us = <130>;
+				exit-latency-us = <80>;
+				min-residency-us = <300>;
+			};
+		};
 	};
 
 	thermal-zones {
@@ -846,10 +867,11 @@
 			clock-names = "ref_clk_src", "ref_clk";
 			clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
 				 <&gcc GCC_UFS_CLKREF_CLK>;
+			resets = <&ufshc 0>;
 			status = "disabled";
 		};
 
-		ufshc@624000 {
+		ufshc: ufshc@624000 {
 			compatible = "qcom,ufshc";
 			reg = <0x624000 0x2500>;
 			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
@@ -905,6 +927,7 @@
 				<0 0>;
 
 			lanes-per-direction = <1>;
+			#reset-cells = <1>;
 			status = "disabled";
 
 			ufs_variant {
@@ -1154,7 +1177,6 @@
 			clock-names = "iface",
 				      "bus";
 			#iommu-cells = <1>;
-			status = "disabled";
 		};
 
 		camss: camss@a00000 {
@@ -1307,8 +1329,6 @@
 			clock-names = "iface", "bus";
 
 			power-domains = <&mmcc GPU_GDSC>;
-
-			status = "disabled";
 		};
 
 		mdp_smmu: arm,smmu@d00000 {
@@ -1325,8 +1345,6 @@
 			clock-names = "iface", "bus";
 
 			power-domains = <&mmcc MDSS_GDSC>;
-
-			status = "disabled";
 		};
 
 		lpass_q6_smmu: arm,smmu-lpass_q6@1600000 {
@@ -1353,7 +1371,6 @@
 			clocks = <&gcc GCC_HLOS1_VOTE_LPASS_CORE_SMMU_CLK>,
 				 <&gcc GCC_HLOS1_VOTE_LPASS_ADSP_SMMU_CLK>;
 			clock-names = "iface", "bus";
-			status = "disabled";
 		};
 
 		agnoc@0 {
@@ -1674,7 +1691,7 @@
 			#interrupt-cells = <1>;
 
 			clocks = <&mmcc MDSS_AHB_CLK>;
-			clock-names = "iface_clk";
+			clock-names = "iface";
 
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -1693,11 +1710,11 @@
 					 <&mmcc MDSS_MDP_CLK>,
 					 <&mmcc SMMU_MDP_AXI_CLK>,
 					 <&mmcc MDSS_VSYNC_CLK>;
-				clock-names = "iface_clk",
-					      "bus_clk",
-					      "core_clk",
-					      "iommu_clk",
-					      "vsync_clk";
+				clock-names = "iface",
+					      "bus",
+					      "core",
+					      "iommu",
+					      "vsync";
 
 				iommus = <&mdp_smmu 0>;
 
@@ -1732,11 +1749,11 @@
 					 <&mmcc MDSS_HDMI_AHB_CLK>,
 					 <&mmcc MDSS_EXTPCLK_CLK>;
 				clock-names =
-					"mdp_core_clk",
-					"iface_clk",
-					"core_clk",
-					"alt_iface_clk",
-					"extp_clk";
+					"mdp_core",
+					"iface",
+					"core",
+					"alt_iface",
+					"extp";
 
 				phys = <&hdmi_phy>;
 				phy-names = "hdmi_phy";
@@ -1773,8 +1790,8 @@
 
 				clocks = <&mmcc MDSS_AHB_CLK>,
 					 <&gcc GCC_HDMI_CLKREF_CLK>;
-				clock-names = "iface_clk",
-					      "ref_clk";
+				clock-names = "iface",
+					      "ref";
 			};
 		};
 	};
@@ -1814,7 +1831,7 @@
 				power-domains = <&gcc HLOS1_VOTE_LPASS_ADSP_GDSC>;
 				compatible = "qcom,apr-v2";
 				qcom,smd-channels = "apr_audio_svc";
-				reg = <APR_DOMAIN_ADSP>;
+				qcom,apr-domain = <APR_DOMAIN_ADSP>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 
diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
index 574be78a936e..c13ed7aeb1e0 100644
--- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
@@ -4,6 +4,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8998.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/gpio/gpio.h>
 
 / {
@@ -78,6 +79,7 @@
 			compatible = "arm,armv8";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
+			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
 			next-level-cache = <&L2_0>;
 			L2_0: l2-cache {
 				compatible = "arm,arch-cache";
@@ -96,6 +98,7 @@
 			compatible = "arm,armv8";
 			reg = <0x0 0x1>;
 			enable-method = "psci";
+			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
 			next-level-cache = <&L2_0>;
 			L1_I_1: l1-icache {
 				compatible = "arm,arch-cache";
@@ -110,6 +113,7 @@
 			compatible = "arm,armv8";
 			reg = <0x0 0x2>;
 			enable-method = "psci";
+			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
 			next-level-cache = <&L2_0>;
 			L1_I_2: l1-icache {
 				compatible = "arm,arch-cache";
@@ -124,6 +128,7 @@
 			compatible = "arm,armv8";
 			reg = <0x0 0x3>;
 			enable-method = "psci";
+			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
 			next-level-cache = <&L2_0>;
 			L1_I_3: l1-icache {
 				compatible = "arm,arch-cache";
@@ -138,6 +143,7 @@
 			compatible = "arm,armv8";
 			reg = <0x0 0x100>;
 			enable-method = "psci";
+			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
 			next-level-cache = <&L2_1>;
 			L2_1: l2-cache {
 				compatible = "arm,arch-cache";
@@ -156,6 +162,7 @@
 			compatible = "arm,armv8";
 			reg = <0x0 0x101>;
 			enable-method = "psci";
+			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
 			next-level-cache = <&L2_1>;
 			L1_I_101: l1-icache {
 				compatible = "arm,arch-cache";
@@ -170,6 +177,7 @@
 			compatible = "arm,armv8";
 			reg = <0x0 0x102>;
 			enable-method = "psci";
+			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
 			next-level-cache = <&L2_1>;
 			L1_I_102: l1-icache {
 				compatible = "arm,arch-cache";
@@ -184,6 +192,7 @@
 			compatible = "arm,armv8";
 			reg = <0x0 0x103>;
 			enable-method = "psci";
+			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
 			next-level-cache = <&L2_1>;
 			L1_I_103: l1-icache {
 				compatible = "arm,arch-cache";
@@ -230,6 +239,48 @@
 				};
 			};
 		};
+
+		idle-states {
+			entry-method = "psci";
+
+			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "little-retention";
+				arm,psci-suspend-param = <0x00000002>;
+				entry-latency-us = <81>;
+				exit-latency-us = <86>;
+				min-residency-us = <200>;
+			};
+
+			LITTLE_CPU_SLEEP_1: cpu-sleep-0-1 {
+				compatible = "arm,idle-state";
+				idle-state-name = "little-power-collapse";
+				arm,psci-suspend-param = <0x40000003>;
+				entry-latency-us = <273>;
+				exit-latency-us = <612>;
+				min-residency-us = <1000>;
+				local-timer-stop;
+			};
+
+			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "big-retention";
+				arm,psci-suspend-param = <0x00000002>;
+				entry-latency-us = <79>;
+				exit-latency-us = <82>;
+				min-residency-us = <200>;
+			};
+
+			BIG_CPU_SLEEP_1: cpu-sleep-1-1 {
+				compatible = "arm,idle-state";
+				idle-state-name = "big-power-collapse";
+				arm,psci-suspend-param = <0x40000003>;
+				entry-latency-us = <336>;
+				exit-latency-us = <525>;
+				min-residency-us = <1000>;
+				local-timer-stop;
+			};
+		};
 	};
 
 	firmware {
@@ -264,6 +315,56 @@
 				compatible = "qcom,rpmcc-msm8998", "qcom,rpmcc";
 				#clock-cells = <1>;
 			};
+
+			rpmpd: power-controller {
+				compatible = "qcom,msm8998-rpmpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmpd_opp_table>;
+
+				rpmpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmpd_opp_ret: opp1 {
+						opp-level = <16>;
+					};
+
+					rpmpd_opp_ret_plus: opp2 {
+						opp-level = <32>;
+					};
+
+					rpmpd_opp_min_svs: opp3 {
+						opp-level = <48>;
+					};
+
+					rpmpd_opp_low_svs: opp4 {
+						opp-level = <64>;
+					};
+
+					rpmpd_opp_svs: opp5 {
+						opp-level = <128>;
+					};
+
+					rpmpd_opp_svs_plus: opp6 {
+						opp-level = <192>;
+					};
+
+					rpmpd_opp_nom: opp7 {
+						opp-level = <256>;
+					};
+
+					rpmpd_opp_nom_plus: opp8 {
+						opp-level = <320>;
+					};
+
+					rpmpd_opp_turbo: opp9 {
+						opp-level = <384>;
+					};
+
+					rpmpd_opp_turbo_plus: opp10 {
+						opp-level = <512>;
+					};
+				};
+			};
 		};
 	};
 
@@ -758,6 +859,90 @@
 			#thermal-sensor-cells = <1>;
 		};
 
+		anoc1_smmu: iommu@1680000 {
+			compatible = "qcom,msm8998-smmu-v2", "qcom,smmu-v2";
+			reg = <0x01680000 0x10000>;
+			#iommu-cells = <1>;
+
+			#global-interrupts = <0>;
+			interrupts =
+				<GIC_SPI 364 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 365 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 366 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 367 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 368 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 369 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		pcie0: pci@1c00000 {
+			compatible = "qcom,pcie-msm8996";
+			reg =	<0x01c00000 0x2000>,
+				<0x1b000000 0xf1d>,
+				<0x1b000f20 0xa8>,
+				<0x1b100000 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			num-lanes = <1>;
+			phys = <&pciephy>;
+			phy-names = "pciephy";
+
+			ranges = <0x01000000 0x0 0x1b200000 0x1b200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x1b300000 0x1b300000 0x0 0xd00000>;
+
+			#interrupt-cells = <1>;
+			interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map =	<0 0 0 1 &intc 0 135 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 136 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 138 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 139 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
+				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_AUX_CLK>;
+			clock-names = "pipe", "bus_master", "bus_slave", "cfg", "aux";
+
+			power-domains = <&gcc PCIE_0_GDSC>;
+			iommu-map = <0x100 &anoc1_smmu 0x1480 1>;
+			perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+		};
+
+		phy@1c06000 {
+			compatible = "qcom,msm8998-qmp-pcie-phy";
+			reg = <0x01c06000 0x18c>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_CLKREF_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_PCIE_0_PHY_BCR>, <&gcc GCC_PCIE_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			vdda-phy-supply = <&vreg_l1a_0p875>;
+			vdda-pll-supply = <&vreg_l2a_1p2>;
+
+			pciephy: lane@1c06800 {
+				reg = <0x01c06200 0x128>, <0x01c06400 0x1fc>, <0x01c06800 0x20c>;
+				#phy-cells = <0>;
+
+				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "pcie_0_pipe_clk_src";
+				#clock-cells = <0>;
+			};
+		};
+
 		tcsr_mutex_regs: syscon@1f40000 {
 			compatible = "syscon";
 			reg = <0x1f40000 0x20000>;
diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
index d3ca35a940fb..051a52df80f9 100644
--- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
@@ -39,7 +39,7 @@
 		#size-cells = <0>;
 
 		pm8998_pon: pon@800 {
-			compatible = "qcom,pm8916-pon";
+			compatible = "qcom,pm8998-pon";
 
 			reg = <0x800>;
 			mode-bootloader = <0x2>;
diff --git a/arch/arm64/boot/dts/qcom/pms405.dtsi b/arch/arm64/boot/dts/qcom/pms405.dtsi
index e8e186bc1ea7..14240fedd916 100644
--- a/arch/arm64/boot/dts/qcom/pms405.dtsi
+++ b/arch/arm64/boot/dts/qcom/pms405.dtsi
@@ -98,7 +98,7 @@
 				qcom,pre-scaling = <1 1>;
 			};
 
-			vph_pwr {
+			pon_1: vph_pwr {
 				reg = <ADC5_VPH_PWR>;
 				qcom,pre-scaling = <1 3>;
 			};
@@ -108,18 +108,24 @@
 				qcom,pre-scaling = <1 1>;
 			};
 
-			xo_therm_100k_pu {
-				reg = <ADC5_XO_THERM_100K_PU>;
+			pa_therm1: thermistor1 {
+				reg = <ADC5_AMUX_THM1_100K_PU>;
+				qcom,ratiometric;
+				qcom,hw-settle-time = <200>;
 				qcom,pre-scaling = <1 1>;
 			};
 
-			amux_thm1_100k_pu {
-				reg = <ADC5_AMUX_THM1_100K_PU>;
+			pa_therm3: thermistor3 {
+				reg = <ADC5_AMUX_THM3_100K_PU>;
+				qcom,ratiometric;
+				qcom,hw-settle-time = <200>;
 				qcom,pre-scaling = <1 1>;
 			};
 
-			amux_thm3_100k_pu {
-				reg = <ADC5_AMUX_THM3_100K_PU>;
+			xo_therm: xo_temp {
+				reg = <ADC5_XO_THERM_100K_PU>;
+				qcom,ratiometric;
+				qcom,hw-settle-time = <200>;
 				qcom,pre-scaling = <1 1>;
 			};
 		};
diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index 2c3127167e3c..11c0a7137823 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 // Copyright (c) 2018, Linaro Limited
 
+#include <dt-bindings/gpio/gpio.h>
 #include "qcs404.dtsi"
 #include "pms405.dtsi"
 
@@ -56,18 +57,41 @@
 	qcom,controlled-remotely;
 };
 
+&gcc {
+	protected-clocks = <GCC_BIMC_CDSP_CLK>,
+			   <GCC_CDSP_CFG_AHB_CLK>,
+			   <GCC_CDSP_BIMC_CLK_SRC>,
+			   <GCC_CDSP_TBU_CLK>;
+};
+
 &pms405_spmi_regulators {
-	vdd_s3-supply = <&pms405_s3>;
+	vdd_s3-supply = <&vph_pwr>;
 
 	pms405_s3: s3 {
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-name = "vdd_apc";
 		regulator-min-microvolt = <1048000>;
-		regulator-max-microvolt = <1352000>;
+		regulator-max-microvolt = <1384000>;
 	};
 };
 
+&pcie {
+	status = "ok";
+
+	perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&perst_state>;
+};
+
+&pcie_phy {
+	status = "ok";
+
+	vdda-vp-supply = <&vreg_l3_1p05>;
+	vdda-vph-supply = <&vreg_l5_1p8>;
+};
+
 &remoteproc_adsp {
 	status = "ok";
 };
@@ -118,7 +142,7 @@
 		};
 
 		vreg_l3_1p05: l3 {
-			regulator-min-microvolt = <1050000>;
+			regulator-min-microvolt = <1048000>;
 			regulator-max-microvolt = <1160000>;
 		};
 
@@ -184,6 +208,15 @@
 };
 
 &tlmm {
+	perst_state: perst {
+		pins = "gpio43";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
 	sdc1_on: sdc1-on {
 		clk {
 			pins = "sdc1_clk";
@@ -200,7 +233,7 @@
 		data {
 			pins = "sdc1_data";
 			bias-pull-up;
-			dreive-strength = <10>;
+			drive-strength = <10>;
 		};
 
 		rclk {
@@ -225,7 +258,7 @@
 		data {
 			pins = "sdc1_data";
 			bias-pull-up;
-			dreive-strength = <2>;
+			drive-strength = <2>;
 		};
 
 		rclk {
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index 65a2cbeb28be..3f17e1b09c13 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -3,7 +3,9 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-qcs404.h>
+#include <dt-bindings/clock/qcom,turingcc-qcs404.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
 
 / {
 	interrupt-parent = <&intc>;
@@ -30,6 +32,7 @@
 			compatible = "arm,cortex-a53";
 			reg = <0x100>;
 			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
 			next-level-cache = <&L2_0>;
 		};
 
@@ -38,6 +41,7 @@
 			compatible = "arm,cortex-a53";
 			reg = <0x101>;
 			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
 			next-level-cache = <&L2_0>;
 		};
 
@@ -46,6 +50,7 @@
 			compatible = "arm,cortex-a53";
 			reg = <0x102>;
 			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
 			next-level-cache = <&L2_0>;
 		};
 
@@ -54,6 +59,7 @@
 			compatible = "arm,cortex-a53";
 			reg = <0x103>;
 			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
 			next-level-cache = <&L2_0>;
 		};
 
@@ -61,6 +67,20 @@
 			compatible = "cache";
 			cache-level = <2>;
 		};
+
+		idle-states {
+			entry-method = "psci";
+
+			CPU_SLEEP_0: cpu-sleep-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "standalone-power-collapse";
+				arm,psci-suspend-param = <0x40000003>;
+				entry-latency-us = <125>;
+				exit-latency-us = <180>;
+				min-residency-us = <595>;
+				local-timer-stop;
+			};
+		};
 	};
 
 	firmware {
@@ -81,99 +101,6 @@
 		method = "smc";
 	};
 
-	remoteproc_adsp: remoteproc-adsp {
-		compatible = "qcom,qcs404-adsp-pas";
-
-		interrupts-extended = <&intc GIC_SPI 293 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
-		interrupt-names = "wdog", "fatal", "ready",
-				  "handover", "stop-ack";
-
-		clocks = <&xo_board>;
-		clock-names = "xo";
-
-		memory-region = <&adsp_fw_mem>;
-
-		qcom,smem-states = <&adsp_smp2p_out 0>;
-		qcom,smem-state-names = "stop";
-
-		status = "disabled";
-
-		glink-edge {
-			interrupts = <GIC_SPI 289 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,remote-pid = <2>;
-			mboxes = <&apcs_glb 8>;
-
-			label = "adsp";
-		};
-	};
-
-	remoteproc_cdsp: remoteproc-cdsp {
-		compatible = "qcom,qcs404-cdsp-pas";
-
-		interrupts-extended = <&intc GIC_SPI 229 IRQ_TYPE_EDGE_RISING>,
-				      <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
-				      <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
-				      <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
-				      <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
-		interrupt-names = "wdog", "fatal", "ready",
-				  "handover", "stop-ack";
-
-		clocks = <&xo_board>;
-		clock-names = "xo";
-
-		memory-region = <&cdsp_fw_mem>;
-
-		qcom,smem-states = <&cdsp_smp2p_out 0>;
-		qcom,smem-state-names = "stop";
-
-		status = "disabled";
-
-		glink-edge {
-			interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,remote-pid = <5>;
-			mboxes = <&apcs_glb 12>;
-
-			label = "cdsp";
-		};
-	};
-
-	remoteproc_wcss: remoteproc-wcss {
-		compatible = "qcom,qcs404-wcss-pas";
-
-		interrupts-extended = <&intc GIC_SPI 153 IRQ_TYPE_EDGE_RISING>,
-				      <&wcss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
-				      <&wcss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
-				      <&wcss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
-				      <&wcss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
-		interrupt-names = "wdog", "fatal", "ready",
-				  "handover", "stop-ack";
-
-		clocks = <&xo_board>;
-		clock-names = "xo";
-
-		memory-region = <&wlan_fw_mem>;
-
-		qcom,smem-states = <&wcss_smp2p_out 0>;
-		qcom,smem-state-names = "stop";
-
-		status = "disabled";
-
-		glink-edge {
-			interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,remote-pid = <1>;
-			mboxes = <&apcs_glb 16>;
-
-			label = "wcss";
-		};
-	};
-
 	reserved-memory {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -230,6 +157,60 @@
 				compatible = "qcom,rpmcc-qcs404";
 				#clock-cells = <1>;
 			};
+
+			rpmpd: power-controller {
+				compatible = "qcom,qcs404-rpmpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmpd_opp_table>;
+
+				rpmpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmpd_opp_ret: opp1 {
+						opp-level = <16>;
+					};
+
+					rpmpd_opp_ret_plus: opp2 {
+						opp-level = <32>;
+					};
+
+					rpmpd_opp_min_svs: opp3 {
+						opp-level = <48>;
+					};
+
+					rpmpd_opp_low_svs: opp4 {
+						opp-level = <64>;
+					};
+
+					rpmpd_opp_svs: opp5 {
+						opp-level = <128>;
+					};
+
+					rpmpd_opp_svs_plus: opp6 {
+						opp-level = <192>;
+					};
+
+					rpmpd_opp_nom: opp7 {
+						opp-level = <256>;
+					};
+
+					rpmpd_opp_nom_plus: opp8 {
+						opp-level = <320>;
+					};
+
+					rpmpd_opp_turbo: opp9 {
+						opp-level = <384>;
+					};
+
+					rpmpd_opp_turbo_no_cpr: opp10 {
+						opp-level = <416>;
+					};
+
+					rpmpd_opp_turbo_plus: opp11 {
+						opp-level = <512>;
+					};
+				};
+			};
 		};
 	};
 
@@ -254,6 +235,17 @@
 		ranges = <0 0 0 0xffffffff>;
 		compatible = "simple-bus";
 
+		turingcc: clock-controller@800000 {
+			compatible = "qcom,qcs404-turingcc";
+			reg = <0x00800000 0x30000>;
+			clocks = <&gcc GCC_CDSP_CFG_AHB_CLK>;
+
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+
+			status = "disabled";
+		};
+
 		rpm_msg_ram: memory@60000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x00060000 0x6000>;
@@ -266,6 +258,57 @@
 			clock-names = "core";
 		};
 
+		remoteproc_cdsp: remoteproc@b00000 {
+			compatible = "qcom,qcs404-cdsp-pas";
+			reg = <0x00b00000 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 229 IRQ_TYPE_EDGE_RISING>,
+					      <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&xo_board>,
+				 <&gcc GCC_CDSP_CFG_AHB_CLK>,
+				 <&gcc GCC_CDSP_TBU_CLK>,
+				 <&gcc GCC_BIMC_CDSP_CLK>,
+				 <&turingcc TURING_WRAPPER_AON_CLK>,
+				 <&turingcc TURING_Q6SS_AHBS_AON_CLK>,
+				 <&turingcc TURING_Q6SS_AHBM_AON_CLK>,
+				 <&turingcc TURING_Q6SS_Q6_AXIM_CLK>;
+			clock-names = "xo",
+				      "sway",
+				      "tbu",
+				      "bimc",
+				      "ahb_aon",
+				      "q6ss_slave",
+				      "q6ss_master",
+				      "q6_axim";
+
+			resets = <&gcc GCC_CDSP_RESTART>;
+			reset-names = "restart";
+
+			qcom,halt-regs = <&tcsr 0x19004>;
+
+			memory-region = <&cdsp_fw_mem>;
+
+			qcom,smem-states = <&cdsp_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,remote-pid = <5>;
+				mboxes = <&apcs_glb 12>;
+
+				label = "cdsp";
+			};
+		};
+
 		tlmm: pinctrl@1000000 {
 			compatible = "qcom,qcs404-pinctrl";
 			reg = <0x01000000 0x200000>,
@@ -394,6 +437,11 @@
 			reg = <0x01905000 0x20000>;
 		};
 
+		tcsr: syscon@1937000 {
+			compatible = "syscon";
+			reg = <0x01937000 0x25000>;
+		};
+
 		spmi_bus: spmi@200f000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0x0200f000 0x001000>,
@@ -412,6 +460,53 @@
 			#interrupt-cells = <4>;
 		};
 
+		remoteproc_wcss: remoteproc@7400000 {
+			compatible = "qcom,qcs404-wcss-pas";
+			reg = <0x07400000 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 153 IRQ_TYPE_EDGE_RISING>,
+					      <&wcss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&wcss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&wcss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&wcss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&xo_board>;
+			clock-names = "xo";
+
+			memory-region = <&wlan_fw_mem>;
+
+			qcom,smem-states = <&wcss_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,remote-pid = <1>;
+				mboxes = <&apcs_glb 16>;
+
+				label = "wcss";
+			};
+		};
+
+		pcie_phy: phy@7786000 {
+			compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy";
+			reg = <0x07786000 0xb8>;
+
+			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+			resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
+				 <&gcc 21>;
+			reset-names = "phy", "pipe";
+
+			clock-output-names = "pcie_0_pipe_clk";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		sdcc1: sdcc@7804000 {
 			compatible = "qcom,sdhci-msm-v5";
 			reg = <0x07804000 0x1000>, <0x7805000 0x1000>;
@@ -797,6 +892,88 @@
 				status = "disabled";
 			};
 		};
+
+		remoteproc_adsp: remoteproc@c700000 {
+			compatible = "qcom,qcs404-adsp-pas";
+			reg = <0x0c700000 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 293 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&xo_board>;
+			clock-names = "xo";
+
+			memory-region = <&adsp_fw_mem>;
+
+			qcom,smem-states = <&adsp_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 289 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,remote-pid = <2>;
+				mboxes = <&apcs_glb 8>;
+
+				label = "adsp";
+			};
+		};
+
+		pcie: pci@10000000 {
+			compatible = "qcom,pcie-qcs404", "snps,dw-pcie";
+			reg =  <0x10000000 0xf1d>,
+			       <0x10000f20 0xa8>,
+			       <0x07780000 0x2000>,
+			       <0x10001000 0x2000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x81000000 0 0          0x10003000 0 0x00010000>, /* I/O */
+				 <0x82000000 0 0x10013000 0x10013000 0 0x007ed000>; /* memory */
+
+			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>;
+			clock-names = "iface", "aux", "master_bus", "slave_bus";
+
+			resets = <&gcc 18>,
+				 <&gcc 17>,
+				 <&gcc 15>,
+				 <&gcc 19>,
+				 <&gcc GCC_PCIE_0_BCR>,
+				 <&gcc 16>;
+			reset-names = "axi_m",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "pipe_sticky",
+				      "pwr",
+				      "ahb";
+
+			phys = <&pcie_phy>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
 	};
 
 	timer {
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
new file mode 100644
index 000000000000..71bd717a4251
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -0,0 +1,557 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/ {
+	model = "Thundercomm Dragonboard 845c";
+	compatible = "thundercomm,db845c", "qcom,sdm845";
+
+	aliases {
+		serial0 = &uart9;
+		hsuart0 = &uart6;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	dc12v: dc12v-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "DC12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vol_up_pin_a>;
+
+		vol-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		user4 {
+			label = "green:user4";
+			gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "panic-indicator";
+			default-state = "off";
+		};
+
+		wlan {
+			label = "yellow:wlan";
+			gpios = <&pm8998_gpio 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tx";
+			default-state = "off";
+		};
+
+		bt {
+			label = "blue:bt";
+			gpios = <&pm8998_gpio 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "bluetooth-power";
+			default-state = "off";
+		};
+	};
+
+	lt9611_1v8: lt9611-vdd18-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_1V8";
+
+		vin-supply = <&vdc_5v>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	lt9611_3v3: lt9611-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_3V3";
+
+		vin-supply = <&vdc_3v3>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		// TODO: make it possible to drive same GPIO from two clients
+		// gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+		// enable-active-high;
+	};
+
+	pcie0_1p05v: pcie-0-1p05v-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "PCIE0_1.05V";
+
+		vin-supply = <&vbat>;
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+
+		// TODO: make it possible to drive same GPIO from two clients
+		// gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
+		// enable-active-high;
+	};
+
+	pcie0_3p3v_dual: vldo-3v3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VLDO_3V3";
+
+		vin-supply = <&vbat>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie0_pwren_state>;
+	};
+
+	v5p0_hdmiout: v5p0-hdmiout-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "V5P0_HDMIOUT";
+
+		vin-supply = <&vdc_5v>;
+		regulator-min-microvolt = <500000>;
+		regulator-max-microvolt = <500000>;
+
+		// TODO: make it possible to drive same GPIO from two clients
+		// gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+		// enable-active-high;
+	};
+
+	vbat: vbat-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VBAT";
+
+		vin-supply = <&dc12v>;
+		regulator-min-microvolt = <4200000>;
+		regulator-max-microvolt = <4200000>;
+		regulator-always-on;
+	};
+
+	vbat_som: vbat-som-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VBAT_SOM";
+
+		vin-supply = <&dc12v>;
+		regulator-min-microvolt = <4200000>;
+		regulator-max-microvolt = <4200000>;
+		regulator-always-on;
+	};
+
+	vdc_3v3: vdc-3v3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VDC_3V3";
+		vin-supply = <&dc12v>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdc_5v: vdc-5v-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VDC_5V";
+
+		vin-supply = <&dc12v>;
+		regulator-min-microvolt = <500000>;
+		regulator-max-microvolt = <500000>;
+		regulator-always-on;
+	};
+
+	vreg_s4a_1p8: vreg-s4a-1p8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s4a_1p8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+
+		vin-supply = <&vbat_som>;
+	};
+};
+
+&adsp_pas {
+	status = "okay";
+
+	firmware-name = "qcom/db845c/adsp.mdt";
+};
+
+&apps_rsc {
+	pm8998-rpmh-regulators {
+		compatible = "qcom,pm8998-rpmh-regulators";
+		qcom,pmic-id = "a";
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+		vdd-s13-supply = <&vph_pwr>;
+		vdd-l1-l27-supply = <&vreg_s7a_1p025>;
+		vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+		vdd-l3-l11-supply = <&vreg_s7a_1p025>;
+		vdd-l4-l5-supply = <&vreg_s7a_1p025>;
+		vdd-l6-supply = <&vph_pwr>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+		vdd-l9-supply = <&vreg_bob>;
+		vdd-l10-l23-l25-supply = <&vreg_bob>;
+		vdd-l13-l19-l21-supply = <&vreg_bob>;
+		vdd-l16-l28-supply = <&vreg_bob>;
+		vdd-l18-l22-supply = <&vreg_bob>;
+		vdd-l20-l24-supply = <&vreg_bob>;
+		vdd-l26-supply = <&vreg_s3a_1p35>;
+		vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p35: smps3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s5a_2p04: smps5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: smps7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vreg_l1a_0p875: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a_2p95: ldo13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17a_1p3: ldo17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a_2p95: ldo20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2968000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a_2p95: ldo21 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2968000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l24a_3p075: ldo24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l25a_3p3: ldo25 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l26a_1p2: ldo26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pmi8998-rpmh-regulators {
+		compatible = "qcom,pmi8998-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+			regulator-allow-bypass;
+		};
+	};
+};
+
+&cdsp_pas {
+	status = "okay";
+	firmware-name = "qcom/db845c/cdsp.mdt";
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+			   <GCC_QSPI_CORE_CLK_SRC>,
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
+};
+
+&pm8998_gpio {
+	vol_up_pin_a: vol-up-active {
+		pins = "gpio6";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+};
+
+&pm8998_pon {
+	resin {
+		compatible = "qcom,pm8941-resin";
+		interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+		debounce = <15625>;
+		bias-pull-up;
+		linux,code = <KEY_VOLUMEDOWN>;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
+
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vreg_l13a_2p95>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
+};
+
+&tlmm {
+	pcie0_pwren_state: pcie0-pwren {
+		pins = "gpio90";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sdc2_default_state: sdc2-default {
+		clk {
+			pins = "sdc2_clk";
+			bias-disable;
+
+			/*
+			 * It seems that mmc_test reports errors if drive
+			 * strength is not 16 on clk, cmd, and data pins.
+			 */
+			drive-strength = <16>;
+		};
+
+		cmd {
+			pins = "sdc2_cmd";
+			bias-pull-up;
+			drive-strength = <10>;
+		};
+
+		data {
+			pins = "sdc2_data";
+			bias-pull-up;
+			drive-strength = <10>;
+		};
+	};
+
+	sdc2_card_det_n: sd-card-det-n {
+		pins = "gpio126";
+		function = "gpio";
+		bias-pull-up;
+	};
+};
+
+&uart6 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&uart9 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l26a_1p2>;
+	vdda-pll-supply = <&vreg_l1a_0p875>;
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
+};
+
+&usb_2_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l26a_1p2>;
+	vdda-pll-supply = <&vreg_l1a_0p875>;
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <800000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&wifi {
+	status = "okay";
+
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+
+&qup_uart6_default {
+	pinmux {
+		pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		function = "qup6";
+	};
+
+	cts {
+		pins = "gpio45";
+		bias-disable;
+	};
+
+	rts-tx {
+		pins = "gpio46", "gpio47";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rx {
+		pins = "gpio48";
+		bias-pull-up;
+	};
+};
+
+&qup_uart9_default {
+	pinconf-tx {
+		pins = "gpio4";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pinconf-rx {
+		pins = "gpio5";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
index 02b8357c8ce8..2e78638eb73b 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
@@ -404,8 +404,8 @@
 };
 
 &usb_1_dwc3 {
-	/* Until we have Type C hooked up we'll force this as host. */
-	dr_mode = "host";
+	/* Until we have Type C hooked up we'll force this as peripheral. */
+	dr_mode = "peripheral";
 };
 
 &usb_1_hsphy {
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index fcb93300ca62..4babff5f19b5 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -190,6 +190,9 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
+			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
+					   &LITTLE_CPU_SLEEP_1
+					   &CLUSTER_SLEEP_0>;
 			capacity-dmips-mhz = <607>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
@@ -208,6 +211,9 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x100>;
 			enable-method = "psci";
+			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
+					   &LITTLE_CPU_SLEEP_1
+					   &CLUSTER_SLEEP_0>;
 			capacity-dmips-mhz = <607>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
@@ -223,6 +229,9 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x200>;
 			enable-method = "psci";
+			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
+					   &LITTLE_CPU_SLEEP_1
+					   &CLUSTER_SLEEP_0>;
 			capacity-dmips-mhz = <607>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
@@ -238,6 +247,9 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x300>;
 			enable-method = "psci";
+			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
+					   &LITTLE_CPU_SLEEP_1
+					   &CLUSTER_SLEEP_0>;
 			capacity-dmips-mhz = <607>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
@@ -254,6 +266,9 @@
 			reg = <0x0 0x400>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
+			cpu-idle-states = <&BIG_CPU_SLEEP_0
+					   &BIG_CPU_SLEEP_1
+					   &CLUSTER_SLEEP_0>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_400>;
@@ -269,6 +284,9 @@
 			reg = <0x0 0x500>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
+			cpu-idle-states = <&BIG_CPU_SLEEP_0
+					   &BIG_CPU_SLEEP_1
+					   &CLUSTER_SLEEP_0>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_500>;
@@ -284,6 +302,9 @@
 			reg = <0x0 0x600>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
+			cpu-idle-states = <&BIG_CPU_SLEEP_0
+					   &BIG_CPU_SLEEP_1
+					   &CLUSTER_SLEEP_0>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_600>;
@@ -299,6 +320,9 @@
 			reg = <0x0 0x700>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
+			cpu-idle-states = <&BIG_CPU_SLEEP_0
+					   &BIG_CPU_SLEEP_1
+					   &CLUSTER_SLEEP_0>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_700>;
@@ -325,26 +349,78 @@
 				core3 {
 					cpu = <&CPU3>;
 				};
-			};
 
-			cluster1 {
-				core0 {
+				core4 {
 					cpu = <&CPU4>;
 				};
 
-				core1 {
+				core5 {
 					cpu = <&CPU5>;
 				};
 
-				core2 {
+				core6 {
 					cpu = <&CPU6>;
 				};
 
-				core3 {
+				core7 {
 					cpu = <&CPU7>;
 				};
 			};
 		};
+
+		idle-states {
+			entry-method = "psci";
+
+			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "little-power-down";
+				arm,psci-suspend-param = <0x40000003>;
+				entry-latency-us = <350>;
+				exit-latency-us = <461>;
+				min-residency-us = <1890>;
+				local-timer-stop;
+			};
+
+			LITTLE_CPU_SLEEP_1: cpu-sleep-0-1 {
+				compatible = "arm,idle-state";
+				idle-state-name = "little-rail-power-down";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <360>;
+				exit-latency-us = <531>;
+				min-residency-us = <3934>;
+				local-timer-stop;
+			};
+
+			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "big-power-down";
+				arm,psci-suspend-param = <0x40000003>;
+				entry-latency-us = <264>;
+				exit-latency-us = <621>;
+				min-residency-us = <952>;
+				local-timer-stop;
+			};
+
+			BIG_CPU_SLEEP_1: cpu-sleep-1-1 {
+				compatible = "arm,idle-state";
+				idle-state-name = "big-rail-power-down";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <702>;
+				exit-latency-us = <1061>;
+				min-residency-us = <4488>;
+				local-timer-stop;
+			};
+
+			CLUSTER_SLEEP_0: cluster-sleep-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "cluster-power-down";
+				arm,psci-suspend-param = <0x400000F4>;
+				entry-latency-us = <3263>;
+				exit-latency-us = <6562>;
+				min-residency-us = <9987>;
+				local-timer-stop;
+			};
+		};
 	};
 
 	pmu {
@@ -1671,6 +1747,64 @@
 			};
 		};
 
+		mss_pil: remoteproc@4080000 {
+			compatible = "qcom,sdm845-mss-pil";
+			reg = <0 0x04080000 0 0x408>, <0 0x04180000 0 0x48>;
+			reg-names = "qdsp6", "rmb";
+
+			interrupts-extended =
+				<&intc GIC_SPI 266 IRQ_TYPE_EDGE_RISING>,
+				<&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+				<&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+				<&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+				<&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+				<&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack",
+					  "shutdown-ack";
+
+			clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+				 <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
+				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
+				 <&gcc GCC_MSS_GPLL0_DIV_CLK_SRC>,
+				 <&gcc GCC_MSS_SNOC_AXI_CLK>,
+				 <&gcc GCC_MSS_MFAB_AXIS_CLK>,
+				 <&gcc GCC_PRNG_AHB_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface", "bus", "mem", "gpll0_mss",
+				      "snoc_axi", "mnoc_axi", "prng", "xo";
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
+				 <&pdc_reset PDC_MODEM_SYNC_RESET>;
+			reset-names = "mss_restart", "pdc_reset";
+
+			qcom,halt-regs = <&tcsr_mutex_regs 0x23000 0x25000 0x24000>;
+
+			power-domains = <&aoss_qmp 2>,
+					<&rpmhpd SDM845_CX>,
+					<&rpmhpd SDM845_MX>,
+					<&rpmhpd SDM845_MSS>;
+			power-domain-names = "load_state", "cx", "mx", "mss";
+
+			mba {
+				memory-region = <&mba_region>;
+			};
+
+			mpss {
+				memory-region = <&mpss_region>;
+			};
+
+			glink-edge {
+				interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>;
+				label = "modem";
+				qcom,remote-pid = <1>;
+				mboxes = <&apss_shared 12>;
+			};
+		};
+
 		gpucc: clock-controller@5090000 {
 			compatible = "qcom,sdm845-gpucc";
 			reg = <0 0x05090000 0 0x9000>;
@@ -2106,6 +2240,133 @@
 			};
 		};
 
+		gpu@5000000 {
+			compatible = "qcom,adreno-630.2", "qcom,adreno";
+			#stream-id-cells = <16>;
+
+			reg = <0 0x5000000 0 0x40000>, <0 0x509e000 0 0x10>;
+			reg-names = "kgsl_3d0_reg_memory", "cx_mem";
+
+			/*
+			 * Look ma, no clocks! The GPU clocks and power are
+			 * controlled entirely by the GMU
+			 */
+
+			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+
+			iommus = <&adreno_smmu 0>;
+
+			operating-points-v2 = <&gpu_opp_table>;
+
+			qcom,gmu = <&gmu>;
+
+			zap-shader {
+				memory-region = <&gpu_mem>;
+			};
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-710000000 {
+					opp-hz = /bits/ 64 <710000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+				};
+
+				opp-675000000 {
+					opp-hz = /bits/ 64 <675000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+				};
+
+				opp-596000000 {
+					opp-hz = /bits/ 64 <596000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+				};
+
+				opp-520000000 {
+					opp-hz = /bits/ 64 <520000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+				};
+
+				opp-414000000 {
+					opp-hz = /bits/ 64 <414000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+				};
+
+				opp-342000000 {
+					opp-hz = /bits/ 64 <342000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+				};
+
+				opp-257000000 {
+					opp-hz = /bits/ 64 <257000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+				};
+			};
+		};
+
+		adreno_smmu: iommu@5040000 {
+			compatible = "qcom,sdm845-smmu-v2", "qcom,smmu-v2";
+			reg = <0 0x5040000 0 0x10000>;
+			#iommu-cells = <1>;
+			#global-interrupts = <2>;
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 364 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 365 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 366 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 367 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 368 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 369 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 370 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 371 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
+			         <&gcc GCC_GPU_CFG_AHB_CLK>;
+			clock-names = "bus", "iface";
+
+			power-domains = <&gpucc GPU_CX_GDSC>;
+		};
+
+		gmu: gmu@506a000 {
+			compatible="qcom,adreno-gmu-630.2", "qcom,adreno-gmu";
+
+			reg = <0 0x506a000 0 0x30000>,
+			      <0 0xb280000 0 0x10000>,
+			      <0 0xb480000 0 0x10000>;
+			reg-names = "gmu", "gmu_pdc", "gmu_pdc_seq";
+
+			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hfi", "gmu";
+
+			clocks = <&gpucc GPU_CC_CX_GMU_CLK>,
+			         <&gpucc GPU_CC_CXO_CLK>,
+				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
+				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>;
+			clock-names = "gmu", "cxo", "axi", "memnoc";
+
+			power-domains = <&gpucc GPU_CX_GDSC>,
+					<&gpucc GPU_GX_GDSC>;
+			power-domain-names = "cx", "gx";
+
+			iommus = <&adreno_smmu 5>;
+
+			operating-points-v2 = <&gmu_opp_table>;
+
+			gmu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-400000000 {
+					opp-hz = /bits/ 64 <400000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+				};
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+				};
+			};
+		};
+
 		dispcc: clock-controller@af00000 {
 			compatible = "qcom,sdm845-dispcc";
 			reg = <0 0x0af00000 0 0x10000>;
@@ -2142,6 +2403,16 @@
 			#reset-cells = <1>;
 		};
 
+		aoss_qmp: qmp@c300000 {
+			compatible = "qcom,sdm845-aoss-qmp";
+			reg = <0 0x0c300000 0 0x100000>;
+			interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>;
+			mboxes = <&apss_shared 0>;
+
+			#clock-cells = <0>;
+			#power-domain-cells = <1>;
+		};
+
 		spmi_bus: spmi@c440000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0 0x0c440000 0 0x1100>,