diff options
| author | Linus Torvalds <torvalds@linux-foundation.org> | 2023-06-29 15:07:06 -0700 |
|---|---|---|
| committer | Linus Torvalds <torvalds@linux-foundation.org> | 2023-06-29 15:07:06 -0700 |
| commit | 6c1561fb900524c5bceb924071b3e9b8a67ff3da (patch) | |
| tree | 3bedd8d3bfac4b15a176e53449b2889418040e44 /arch/arm64/boot/dts/xilinx | |
| parent | b775d6c5859affe00527cbe74263de05cfe6b9f9 (diff) | |
| parent | 46448b36ff8c807194d5884a6efce00891e4bd02 (diff) | |
Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
Diffstat (limited to 'arch/arm64/boot/dts/xilinx')
25 files changed, 596 insertions, 208 deletions
diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile index 4e159540d031..5e40c0b4fa0a 100644 --- a/arch/arm64/boot/dts/xilinx/Makefile +++ b/arch/arm64/boot/dts/xilinx/Makefile @@ -2,7 +2,6 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += avnet-ultra96-rev1.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1232-revA.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1254-revA.dtb -dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1275-revA.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm015-dc1.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm016-dc2.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm017-dc3.dtb @@ -17,16 +16,17 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revA.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revC.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu106-revA.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu111-revA.dtb +dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu1275-revA.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-sm-k26-revA.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-smk-k26-revA.dtb -sm-k26-revA-sck-kv-g-revA-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kv-g-revA.dtbo -sm-k26-revA-sck-kv-g-revB-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kv-g-revB.dtbo -smk-k26-revA-sm-k26-revA-sck-kv-g-revA-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kv-g-revA.dtbo -smk-k26-revA-sm-k26-revA-sck-kv-g-revB-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kv-g-revB.dtbo +zynqmp-sm-k26-revA-sck-kv-g-revA-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kv-g-revA.dtbo +zynqmp-sm-k26-revA-sck-kv-g-revB-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kv-g-revB.dtbo +zynqmp-smk-k26-revA-sck-kv-g-revA-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kv-g-revA.dtbo +zynqmp-smk-k26-revA-sck-kv-g-revB-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kv-g-revB.dtbo -dtb-$(CONFIG_ARCH_ZYNQMP) += sm-k26-revA-sck-kv-g-revA.dtb -dtb-$(CONFIG_ARCH_ZYNQMP) += sm-k26-revA-sck-kv-g-revB.dtb -dtb-$(CONFIG_ARCH_ZYNQMP) += smk-k26-revA-sm-k26-revA-sck-kv-g-revA.dtb -dtb-$(CONFIG_ARCH_ZYNQMP) += smk-k26-revA-sm-k26-revA-sck-kv-g-revB.dtb +zynqmp-sm-k26-revA-sck-kr-g-revA-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kr-g-revA.dtbo +zynqmp-sm-k26-revA-sck-kr-g-revB-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kr-g-revB.dtbo +zynqmp-smk-k26-revA-sck-kr-g-revA-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kr-g-revA.dtbo +zynqmp-smk-k26-revA-sck-kr-g-revB-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kr-g-revB.dtbo diff --git a/arch/arm64/boot/dts/xilinx/avnet-ultra96-rev1.dts b/arch/arm64/boot/dts/xilinx/avnet-ultra96-rev1.dts index 88aa06fa78a8..4c1bd69e7553 100644 --- a/arch/arm64/boot/dts/xilinx/avnet-ultra96-rev1.dts +++ b/arch/arm64/boot/dts/xilinx/avnet-ultra96-rev1.dts @@ -4,7 +4,7 @@ * * (C) Copyright 2018, Xilinx, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi index 3e9979ab60bb..f04716841a0c 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi @@ -2,38 +2,44 @@ /* * Clock specification for Xilinx ZynqMP * - * (C) Copyright 2017 - 2021, Xilinx, Inc. + * (C) Copyright 2017 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ #include <dt-bindings/clock/xlnx-zynqmp-clk.h> / { pss_ref_clk: pss_ref_clk { + bootph-all; compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <33333333>; }; video_clk: video_clk { + bootph-all; compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <27000000>; }; pss_alt_ref_clk: pss_alt_ref_clk { + bootph-all; compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <0>; }; gt_crx_ref_clk: gt_crx_ref_clk { + bootph-all; compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <108000000>; }; aux_ref_clk: aux_ref_clk { + bootph-all; compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <27000000>; @@ -42,6 +48,7 @@ &zynqmp_firmware { zynqmp_clk: clock-controller { + bootph-all; #clock-cells = <1>; compatible = "xlnx,zynqmp-clk"; clocks = <&pss_ref_clk>, <&video_clk>, <&pss_alt_ref_clk>, @@ -95,6 +102,10 @@ clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>; }; +&gpu { + clocks = <&zynqmp_clk GPU_REF>, <&zynqmp_clk GPU_PP0_REF>; +}; + &lpd_dma_chan1 { clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>; }; @@ -181,10 +192,12 @@ &sdhci0 { clocks = <&zynqmp_clk SDIO0_REF>, <&zynqmp_clk LPD_LSBUS>; + assigned-clocks = <&zynqmp_clk SDIO0_REF>; }; &sdhci1 { clocks = <&zynqmp_clk SDIO1_REF>, <&zynqmp_clk LPD_LSBUS>; + assigned-clocks = <&zynqmp_clk SDIO1_REF>; }; &spi0 { @@ -241,10 +254,14 @@ &zynqmp_dpdma { clocks = <&zynqmp_clk DPDMA_REF>; + assigned-clocks = <&zynqmp_clk DPDMA_REF>; /* apll */ }; &zynqmp_dpsub { clocks = <&zynqmp_clk TOPSW_LSBUS>, <&zynqmp_clk DP_AUDIO_REF>, <&zynqmp_clk DP_VIDEO_REF>; + assigned-clocks = <&zynqmp_clk DP_STC_REF>, + <&zynqmp_clk DP_AUDIO_REF>, + <&zynqmp_clk DP_VIDEO_REF>; /* rpll, rpll, vpll */ }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso index b610e65e0cdf..603839c82599 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso +++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso @@ -2,14 +2,15 @@ /* * dts file for KV260 revA Carrier Card * - * (C) Copyright 2020 - 2021, Xilinx, Inc. + * (C) Copyright 2020 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * * SD level shifter: - * "A" – A01 board un-modified (NXP) - * "Y" – A01 board modified with legacy interposer (Nexperia) - * "Z" – A01 board modified with Diode interposer + * "A" - A01 board un-modified (NXP) + * "Y" - A01 board modified with legacy interposer (Nexperia) + * "Z" - A01 board modified with Diode interposer * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ #include <dt-bindings/gpio/gpio.h> @@ -95,13 +96,15 @@ }; &zynqmp_dpsub { - status = "disabled"; + status = "okay"; phy-names = "dp-phy0", "dp-phy1"; phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>; + assigned-clock-rates = <27000000>, <25000000>, <300000000>; }; &zynqmp_dpdma { status = "okay"; + assigned-clock-rates = <600000000>; }; &usb0 { @@ -132,6 +135,8 @@ no-1-8-v; disable-wp; xlnx,mio-bank = <1>; + assigned-clock-rates = <187498123>; + bus-width = <4>; }; &gem3 { /* required by spec */ @@ -144,16 +149,18 @@ mdio: mdio { #address-cells = <1>; #size-cells = <0>; - reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>; - reset-delay-us = <2>; phy0: ethernet-phy@1 { #phy-cells = <1>; reg = <1>; + compatible = "ethernet-phy-id2000.a231"; ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; ti,dp83867-rxctrl-strap-quirk; + reset-assert-us = <100>; + reset-deassert-us = <280>; + reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>; }; }; }; @@ -259,19 +266,22 @@ pinctrl_usb0_default: usb0-default { conf { groups = "usb0_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; }; conf-rx { pins = "MIO52", "MIO53", "MIO55"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", "MIO60", "MIO61", "MIO62", "MIO63"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; mux { diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso index a52dafbfd59e..a91d09e7da4b 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso +++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso @@ -2,9 +2,10 @@ /* * dts file for KV260 revA Carrier Card * - * (C) Copyright 2020 - 2021, Xilinx, Inc. + * (C) Copyright 2020 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ #include <dt-bindings/gpio/gpio.h> @@ -76,13 +77,15 @@ }; &zynqmp_dpsub { - status = "disabled"; + status = "okay"; phy-names = "dp-phy0", "dp-phy1"; phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>; + assigned-clock-rates = <27000000>, <25000000>, <300000000>; }; &zynqmp_dpdma { status = "okay"; + assigned-clock-rates = <600000000>; }; &usb0 { @@ -115,6 +118,8 @@ clk-phase-sd-hs = <126>, <60>; clk-phase-uhs-sdr25 = <120>, <60>; clk-phase-uhs-ddr50 = <126>, <48>; + assigned-clock-rates = <187498123>; + bus-width = <4>; }; &gem3 { /* required by spec */ @@ -127,16 +132,18 @@ mdio: mdio { #address-cells = <1>; #size-cells = <0>; - reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>; - reset-delay-us = <2>; phy0: ethernet-phy@1 { #phy-cells = <1>; reg = <1>; + compatible = "ethernet-phy-id2000.a231"; ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; ti,dp83867-rxctrl-strap-quirk; + reset-assert-us = <100>; + reset-deassert-us = <280>; + reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>; }; }; }; @@ -242,19 +249,22 @@ pinctrl_usb0_default: usb0-default { conf { groups = "usb0_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; }; conf-rx { pins = "MIO52", "MIO53", "MIO55"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", "MIO60", "MIO61", "MIO62", "MIO63"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; mux { diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts index 20e83ca47b5d..dfd1a18f5a10 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts @@ -4,7 +4,7 @@ * * (C) Copyright 2020 - 2021, Xilinx, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; @@ -14,6 +14,7 @@ #include <dt-bindings/input/input.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/phy/phy.h> +#include <dt-bindings/pinctrl/pinctrl-zynqmp.h> / { model = "ZynqMP SM-K26 Rev1/B/A"; @@ -55,6 +56,9 @@ key-fwuen { label = "fwuen"; gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + linux,code = <BTN_MISC>; + wakeup-source; + autorepeat; }; }; @@ -72,109 +76,158 @@ default-state = "on"; }; }; + + ams { + compatible = "iio-hwmon"; + io-channels = <&xilinx_ams 0>, <&xilinx_ams 1>, <&xilinx_ams 2>, + <&xilinx_ams 3>, <&xilinx_ams 4>, <&xilinx_ams 5>, + <&xilinx_ams 6>, <&xilinx_ams 7>, <&xilinx_ams 8>, + <&xilinx_ams 9>, <&xilinx_ams 10>, <&xilinx_ams 11>, + <&xilinx_ams 12>, <&xilinx_ams 13>, <&xilinx_ams 14>, + <&xilinx_ams 15>, <&xilinx_ams 16>, <&xilinx_ams 17>, + <&xilinx_ams 18>, <&xilinx_ams 19>, <&xilinx_ams 20>, + <&xilinx_ams 21>, <&xilinx_ams 22>, <&xilinx_ams 23>, + <&xilinx_ams 24>, <&xilinx_ams 25>, <&xilinx_ams 26>, + <&xilinx_ams 27>, <&xilinx_ams 28>, <&xilinx_ams 29>; + }; +}; + +&modepin_gpio { + label = "modepin"; }; &uart1 { /* MIO36/MIO37 */ status = "okay"; }; +&pinctrl0 { + status = "okay"; + pinctrl_sdhci0_default: sdhci0-default { + conf { + groups = "sdio0_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + bias-disable; + }; + + mux { + groups = "sdio0_0_grp"; + function = "sdio0"; + }; + }; +}; + &qspi { /* MIO 0-5 - U143 */ status = "okay"; - flash@0 { /* MT25QU512A */ + spi_flash: flash@0 { /* MT25QU512A */ compatible = "mt25qu512a", "jedec,spi-nor"; /* 64MB */ #address-cells = <1>; #size-cells = <1>; reg = <0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; spi-max-frequency = <40000000>; /* 40MHz */ - partition@0 { - label = "Image Selector"; - reg = <0x0 0x80000>; /* 512KB */ - read-only; - lock; - }; - partition@80000 { - label = "Image Selector Golden"; - reg = <0x80000 0x80000>; /* 512KB */ - read-only; - lock; - }; - partition@100000 { - label = "Persistent Register"; - reg = <0x100000 0x20000>; /* 128KB */ - }; - partition@120000 { - label = "Persistent Register Backup"; - reg = <0x120000 0x20000>; /* 128KB */ - }; - partition@140000 { - label = "Open_1"; - reg = <0x140000 0xC0000>; /* 768KB */ - }; - partition@200000 { - label = "Image A (FSBL, PMU, ATF, U-Boot)"; - reg = <0x200000 0xD00000>; /* 13MB */ - }; - partition@f00000 { - label = "ImgSel Image A Catch"; - reg = <0xF00000 0x80000>; /* 512KB */ - read-only; - lock; - }; - partition@f80000 { - label = "Image B (FSBL, PMU, ATF, U-Boot)"; - reg = <0xF80000 0xD00000>; /* 13MB */ - }; - partition@1c80000 { - label = "ImgSel Image B Catch"; - reg = <0x1C80000 0x80000>; /* 512KB */ - read-only; - lock; - }; - partition@1d00000 { - label = "Open_2"; - reg = <0x1D00000 0x100000>; /* 1MB */ - }; - partition@1e00000 { - label = "Recovery Image"; - reg = <0x1E00000 0x200000>; /* 2MB */ - read-only; - lock; - }; - partition@2000000 { - label = "Recovery Image Backup"; - reg = <0x2000000 0x200000>; /* 2MB */ - read-only; - lock; - }; - partition@2200000 { - label = "U-Boot storage variables"; - reg = <0x2200000 0x20000>; /* 128KB */ - }; - partition@2220000 { - label = "U-Boot storage variables backup"; - reg = <0x2220000 0x20000>; /* 128KB */ - }; - partition@2240000 { - label = "SHA256"; - reg = <0x2240000 0x10000>; /* 256B but 64KB sector */ - read-only; - lock; - }; - partition@2250000 { - label = "User"; - reg = <0x2250000 0x1db0000>; /* 29.5 MB */ + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Image Selector"; + reg = <0x0 0x80000>; /* 512KB */ + read-only; + lock; + }; + partition@80000 { + label = "Image Selector Golden"; + reg = <0x80000 0x80000>; /* 512KB */ + read-only; + lock; + }; + partition@100000 { + label = "Persistent Register"; + reg = <0x100000 0x20000>; /* 128KB */ + }; + partition@120000 { + label = "Persistent Register Backup"; + reg = <0x120000 0x20000>; /* 128KB */ + }; + partition@140000 { + label = "Open_1"; + reg = <0x140000 0xC0000>; /* 768KB */ + }; + partition@200000 { + label = "Image A (FSBL, PMU, ATF, U-Boot)"; + reg = <0x200000 0xD00000>; /* 13MB */ + }; + partition@f00000 { + label = "ImgSel Image A Catch"; + reg = <0xF00000 0x80000>; /* 512KB */ + read-only; + lock; + }; + partition@f80000 { + label = "Image B (FSBL, PMU, ATF, U-Boot)"; + reg = <0xF80000 0xD00000>; /* 13MB */ + }; + partition@1c80000 { + label = "ImgSel Image B Catch"; + reg = <0x1C80000 0x80000>; /* 512KB */ + read-only; + lock; + }; + partition@1d00000 { + label = "Open_2"; + reg = <0x1D00000 0x100000>; /* 1MB */ + }; + partition@1e00000 { + label = "Recovery Image"; + reg = <0x1E00000 0x200000>; /* 2MB */ + read-only; + lock; + }; + partition@2000000 { + label = "Recovery Image Backup"; + reg = <0x2000000 0x200000>; /* 2MB */ + read-only; + lock; + }; + partition@2200000 { + label = "U-Boot storage variables"; + reg = <0x2200000 0x20000>; /* 128KB */ + }; + partition@2220000 { + label = "U-Boot storage variables backup"; + reg = <0x2220000 0x20000>; /* 128KB */ + }; + partition@2240000 { + label = "SHA256"; + reg = <0x2240000 0x40000>; /* 256B but 256KB sector */ + read-only; + lock; + }; + partition@2280000 { + label = "Secure OS Storage"; + reg = <0x2280000 0x20000>; /* 128KB */ + }; + partition@22A0000 { + label = "User"; + reg = <0x22A0000 0x1d60000>; /* 29.375 MB */ + }; }; }; }; &sdhci0 { /* MIO13-23 - 16GB emmc MTFC16GAPALBH-IT - U133A */ status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhci0_default>; non-removable; disable-wp; bus-width = <8>; xlnx,mio-bank = <0>; + assigned-clock-rates = <187498123>; }; &spi1 { /* MIO6, 9-11 */ @@ -190,17 +243,20 @@ &i2c1 { status = "okay"; + bootph-all; clock-frequency = <400000>; scl-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>; sda-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>; eeprom: eeprom@50 { /* u46 - also at address 0x58 */ + bootph-all; compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */ reg = <0x50>; /* WP pin EE_WP_EN connected to slg7x644092@68 */ }; eeprom_cc: eeprom@51 { /* required by spec - also at address 0x59 */ + bootph-all; compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */ reg = <0x51>; }; @@ -287,3 +343,114 @@ "", "", "", "", "", /* 165 - 169 */ "", "", "", ""; /* 170 - 173 */ }; + +&xilinx_ams { + status = "okay"; +}; + +&ams_ps { + status = "okay"; +}; + +&ams_pl { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; +}; + +&rtc { + status = "okay"; +}; + +&lpd_dma_chan1 { + status = "okay"; +}; + +&lpd_dma_chan2 { + status = "okay"; +}; + +&lpd_dma_chan3 { + status = "okay"; +}; + +&lpd_dma_chan4 { + status = "okay"; +}; + +&lpd_dma_chan5 { + status = "okay"; +}; + +&lpd_dma_chan6 { + status = "okay"; +}; + +&lpd_dma_chan7 { + status = "okay"; +}; + +&lpd_dma_chan8 { + status = "okay"; +}; + +&fpd_dma_chan1 { + status = "okay"; +}; + +&fpd_dma_chan2 { + status = "okay"; +}; + +&fpd_dma_chan3 { + status = "okay"; +}; + +&fpd_dma_chan4 { + status = "okay"; +}; + +&fpd_dma_chan5 { + status = "okay"; +}; + +&fpd_dma_chan6 { + status = "okay"; +}; + +&fpd_dma_chan7 { + status = "okay"; +}; + +&fpd_dma_chan8 { + status = "okay"; +}; + +&gpu { + status = "okay"; +}; + +&lpd_watchdog { + status = "okay"; +}; + +&watchdog0 { + status = "okay"; +}; + +&cpu_opp_table { + opp00 { + opp-hz = /bits/ 64 <1333333333>; + }; + opp01 { + opp-hz = /bits/ 64 <666666666>; + }; + opp02 { + opp-hz = /bits/ 64 <444444444>; + }; + opp03 { + opp-hz = /bits/ 64 <333333333>; + }; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts index c70966c1f344..85b0d1677240 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts @@ -4,7 +4,7 @@ * * (C) Copyright 2020 - 2021, Xilinx, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ #include "zynqmp-sm-k26-revA.dts" diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts index f1598527e5ec..04079d1704f1 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts @@ -4,7 +4,7 @@ * * (C) Copyright 2017 - 2021, Xilinx, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; @@ -44,7 +44,7 @@ #address-cells = <1>; #size-cells = <1>; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; spi-max-frequency = <108000000>; /* Based on DC1 spec */ }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts index 04efa1683eaa..3dec57cf18be 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts @@ -4,8 +4,8 @@ * * (C) Copyright 2015 - 2021, Xilinx, Inc. * - * Michal Simek <michal.simek@xilinx.com> - * Siva Durga Prasad Paladugu <sivadur@xilinx.com> + * Michal Simek <michal.simek@amd.com> + * Siva Durga Prasad Paladugu <siva.durga.prasad.paladugu@amd.com> */ /dts-v1/; @@ -45,7 +45,7 @@ #address-cells = <1>; #size-cells = <1>; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */ spi-max-frequency = <108000000>; /* Based on DC1 spec */ }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts index b05be2552826..d9d1de5f313c 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts @@ -2,9 +2,10 @@ /* * dts file for Xilinx ZynqMP zc1751-xm015-dc1 * - * (C) Copyright 2015 - 2021, Xilinx, Inc. + * (C) Copyright 2015 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; @@ -108,6 +109,9 @@ pinctrl-0 = <&pinctrl_gpio_default>; }; +&gpu { + status = "okay"; +}; &i2c1 { status = "okay"; @@ -184,19 +188,22 @@ conf { groups = "usb0_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; }; conf-rx { pins = "MIO52", "MIO53", "MIO55"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", "MIO60", "MIO61", "MIO62", "MIO63"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; }; @@ -348,7 +355,7 @@ #address-cells = <1>; #size-cells = <1>; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; spi-max-frequency = <108000000>; /* Based on DC1 spec */ }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts index 938b76bd0527..6503f4985f8d 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts @@ -2,9 +2,10 @@ /* * dts file for Xilinx ZynqMP zc1751-xm016-dc2 * - * (C) Copyright 2015 - 2021, Xilinx, Inc. + * (C) Copyright 2015 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; @@ -281,19 +282,22 @@ conf { groups = "usb1_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; }; conf-rx { pins = "MIO64", "MIO65", "MIO67"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71", "MIO72", "MIO73", "MIO74", "MIO75"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; }; @@ -485,8 +489,6 @@ &dwc3_1 { status = "okay"; dr_mode = "host"; - snps,usb3_lpm_capable; - maximum-speed = "super-speed"; }; &uart0 { diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts index 381cc682cef9..38b0a312171b 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts @@ -4,7 +4,7 @@ * * (C) Copyright 2016 - 2021, Xilinx, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts index 05a2b79738af..6636e76545a5 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts @@ -4,7 +4,7 @@ * * (C) Copyright 2015 - 2021, Xilinx, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; @@ -152,6 +152,10 @@ status = "okay"; }; +&gpu { + status = "okay"; +}; + &i2c0 { clock-frequency = <400000>; status = "okay"; @@ -169,7 +173,7 @@ #address-cells = <1>; #size-cells = <1>; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; /* also DUAL configuration possible */ spi-max-frequency = <108000000>; /* Based on DC1 spec */ }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts index ae2d03d98322..b1e933b8a2cd 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts @@ -4,8 +4,8 @@ * * (C) Copyright 2015 - 2021, Xilinx, Inc. * - * Siva Durga Prasad <siva.durga.paladugu@xilinx.com> - * Michal Simek <michal.simek@xilinx.com> + * Siva Durga Prasad Paladugu <siva.durga.prasad.paladugu@amd.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts index 6948fd40554b..44d1f351bb75 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts @@ -2,9 +2,10 @@ /* * dts file for Xilinx ZynqMP ZCU100 revC * - * (C) Copyright 2016 - 2021, Xilinx, Inc. + * (C) Copyright 2016 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> * Nathalie Chan King Choy */ @@ -58,6 +59,15 @@ }; }; + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&xilinx_ams 0>, <&xilinx_ams 1>, <&xilinx_ams 2>, + <&xilinx_ams 3>, <&xilinx_ams 4>, <&xilinx_ams 5>, + <&xilinx_ams 6>, <&xilinx_ams 7>, <&xilinx_ams 8>, + <&xilinx_ams 9>, <&xilinx_ams 10>, + <&xilinx_ams 11>, <&xilinx_ams 12>; + }; + leds { compatible = "gpio-leds"; led-ds2 { @@ -161,6 +171,10 @@ "", "", "", ""; }; +&gpu { + status = "okay"; +}; + &i2c1 { status = "okay"; pinctrl-names = "default", "gpio"; @@ -419,19 +433,22 @@ conf { groups = "usb0_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; }; conf-rx { pins = "MIO52", "MIO53", "MIO55"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", "MIO60", "MIO61", "MIO62", "MIO63"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; }; @@ -443,19 +460,22 @@ conf { groups = "usb1_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; }; conf-rx { pins = "MIO64", "MIO65", "MIO67"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71", "MIO72", "MIO73", "MIO74", "MIO75"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; }; }; @@ -541,6 +561,7 @@ pinctrl-0 = <&pinctrl_usb0_default>; phy-names = "usb3-phy"; phys = <&psgtr 2 PHY_TYPE_USB3 0 0>; + /delete-property/ reset-gpios; }; &dwc3_0 { @@ -556,6 +577,7 @@ pinctrl-0 = <&pinctrl_usb1_default>; phy-names = "usb3-phy"; phys = <&psgtr 3 PHY_TYPE_USB3 1 0>; + reset-gpios = <&modepin_gpio 1 GPIO_ACTIVE_LOW>; }; &dwc3_1 { @@ -568,6 +590,14 @@ status = "okay"; }; +&xilinx_ams { + status = "okay"; +}; + +&ams_ps { + status = "okay"; +}; + &zynqmp_dpdma { status = "okay"; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts index 6647e97edba3..c8f71a1aec89 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts @@ -4,7 +4,7 @@ * * (C) Copyright 2016 - 2018, Xilinx, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ #include "zynqmp-zcu102-revB.dts" diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts index b6798394fcf4..705369766a55 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts @@ -4,7 +4,7 @@ * * (C) Copyright 2016 - 2020, Xilinx, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ #include "zynqmp-zcu102-rev1.0.dts" diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts index 5fd6b70a154a..8767f147cbe3 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts @@ -2,9 +2,10 @@ /* * dts file for Xilinx ZynqMP ZCU102 RevA * - * (C) Copyright 2015 - 2021, Xilinx, Inc. + * (C) Copyright 2015 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; @@ -200,13 +201,19 @@ phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; - phy0: ethernet-phy@21 { - reg = <21>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; - /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */ + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@21 { + #phy-cells = <1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <21>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; }; }; @@ -216,6 +223,10 @@ pinctrl-0 = <&pinctrl_gpio_default>; }; +&gpu { + status = "okay"; +}; + &i2c0 { status = "okay"; clock-frequency = <400000>; @@ -772,19 +783,22 @@ conf { groups = "usb0_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; }; conf-rx { pins = "MIO52", "MIO53", "MIO55"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", "MIO60", "MIO61", "MIO62", "MIO63"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; }; @@ -943,7 +957,7 @@ #address-cells = <1>; #size-cells = <1>; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */ spi-max-frequency = <108000000>; /* Based on DC1 spec */ }; @@ -1013,6 +1027,18 @@ status = "okay"; }; +&xilinx_ams { + status = "okay"; +}; + +&ams_ps { + status = "okay"; +}; + +&ams_pl { + status = "okay"; +}; + &zynqmp_dpdma { status = "okay"; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts index f7d718ff116b..3c28130909bc 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts @@ -2,9 +2,10 @@ /* * dts file for Xilinx ZynqMP ZCU102 RevB * - * (C) Copyright 2016 - 2021, Xilinx, Inc. + * (C) Copyright 2016 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ #include "zynqmp-zcu102-revA.dts" @@ -16,16 +17,20 @@ &gem3 { phy-handle = <&phyc>; - phyc: ethernet-phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; - /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */ + mdio: mdio { + phyc: ethernet-phy@c { + #phy-cells = <0x1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; + /* Cleanup from RevA */ + /delete-node/ ethernet-phy@21; }; - /* Cleanup from RevA */ - /delete-node/ ethernet-phy@21; }; /* Fix collision with u61 */ diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts index bd8f20f3223d..e185709c0d84 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts @@ -2,9 +2,10 @@ /* * dts file for Xilinx ZynqMP ZCU104 * - * (C) Copyright 2017 - 2021, Xilinx, Inc. + * (C) Copyright 2017 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; @@ -109,12 +110,19 @@ phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; - phy0: ethernet-phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@c { + #phy-cells = <1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; }; }; @@ -122,6 +130,10 @@ status = "okay"; }; +&gpu { + status = "okay"; +}; + &i2c1 { status = "okay"; clock-frequency = <400000>; @@ -398,20 +410,22 @@ conf { groups = "usb0_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; - drive-strength = <12>; }; conf-rx { pins = "MIO52", "MIO53", "MIO55"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", "MIO60", "MIO61", "MIO62", "MIO63"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; }; }; @@ -430,7 +444,7 @@ #address-cells = <1>; #size-cells = <1>; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; spi-max-frequency = <108000000>; /* Based on DC1 spec */ }; @@ -497,6 +511,18 @@ status = "okay"; }; +&xilinx_ams { + status = "okay"; +}; + +&ams_ps { + status = "okay"; +}; + +&ams_pl { + status = "okay"; +}; + &zynqmp_dpdma { status = "okay"; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts index 96feaad30166..7fceebd1815c 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts @@ -2,9 +2,10 @@ /* * dts file for Xilinx ZynqMP ZCU104 * - * (C) Copyright 2017 - 2021, Xilinx, Inc. + * (C) Copyright 2017 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; @@ -114,12 +115,19 @@ phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; - phy0: ethernet-phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@c { + #phy-cells = <1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; }; }; @@ -127,6 +135,10 @@ status = "okay"; }; +&gpu { + status = "okay"; +}; + &i2c1 { status = "okay"; clock-frequency = <400000>; @@ -410,20 +422,22 @@ conf { groups = "usb0_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; - drive-strength = <12>; }; conf-rx { pins = "MIO52", "MIO53", "MIO55"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", "MIO60", "MIO61", "MIO62", "MIO63"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; }; }; @@ -442,7 +456,7 @@ #address-cells = <1>; #size-cells = <1>; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; spi-max-frequency = <108000000>; /* Based on DC1 spec */ }; @@ -509,6 +523,18 @@ status = "okay"; }; +&xilinx_ams { + status = "okay"; +}; + +&ams_ps { + status = "okay"; +}; + +&ams_pl { + status = "okay"; +}; + &zynqmp_dpdma { status = "okay"; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts index 24a252317150..27b2416cb6d8 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts @@ -2,9 +2,10 @@ /* * dts file for Xilinx ZynqMP ZCU106 * - * (C) Copyright 2016 - 2021, Xilinx, Inc. + * (C) Copyright 2016 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; @@ -212,12 +213,19 @@ phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; - phy0: ethernet-phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@c { + #phy-cells = <1>; + reg = <0xc>; + compatible = "ethernet-phy-id2000.a231"; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; }; }; @@ -227,6 +235,10 @@ pinctrl-0 = <&pinctrl_gpio_default>; }; +&gpu { + status = "okay"; +}; + &i2c0 { status = "okay"; clock-frequency = <400000>; @@ -782,19 +794,22 @@ conf { groups = "usb0_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; }; conf-rx { pins = "MIO52", "MIO53", "MIO55"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", "MIO60", "MIO61", "MIO62", "MIO63"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; }; @@ -949,7 +964,7 @@ #address-cells = <1>; #size-cells = <1>; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */ spi-max-frequency = <108000000>; /* Based on DC1 spec */ }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts index d685d8fbc36a..6224365826d8 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts @@ -2,9 +2,10 @@ /* * dts file for Xilinx ZynqMP ZCU111 * - * (C) Copyright 2017 - 2021, Xilinx, Inc. + * (C) Copyright 2017 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; @@ -172,12 +173,19 @@ phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; - phy0: ethernet-phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@c { + #phy-cells = <1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u22 6 GPIO_ACTIVE_LOW>; + }; }; }; @@ -187,6 +195,10 @@ pinctrl-0 = <&pinctrl_gpio_default>; }; +&gpu { + status = "okay"; +}; + &i2c0 { status = "okay"; clock-frequency = <400000>; @@ -648,19 +660,22 @@ conf { groups = "usb0_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; }; conf-rx { pins = "MIO52", "MIO53", "MIO55"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", "MIO60", "MIO61", "MIO62", "MIO63"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; }; @@ -779,7 +794,7 @@ #address-cells = <1>; #size-cells = <1>; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */ spi-max-frequency = <108000000>; /* Based on DC1 spec */ }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu1275-revA.dts index e971ba8c1418..c406017b0348 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu1275-revA.dts @@ -4,8 +4,8 @@ * * (C) Copyright 2017 - 2021, Xilinx, Inc. * - * Michal Simek <michal.simek@xilinx.com> - * Siva Durga Prasad Paladugu <sivadur@xilinx.com> + * Michal Simek <michal.simek@amd.com> + * Siva Durga Prasad Paladugu <siva.durga.prasad.paladugu@amd.com> */ /dts-v1/; @@ -14,8 +14,8 @@ #include "zynqmp-clk-ccf.dtsi" / { - model = "ZynqMP ZC1275 RevA"; - compatible = "xlnx,zynqmp-zc1275-revA", "xlnx,zynqmp-zc1275", "xlnx,zynqmp"; + model = "ZynqMP ZCU1275 RevA"; + compatible = "xlnx,zynqmp-zcu1275-revA", "xlnx,zynqmp-zcu1275", "xlnx,zynqmp"; aliases { serial0 = &uart0; @@ -47,7 +47,7 @@ flash@0 { compatible = "m25p80", "jedec,spi-nor"; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; spi-max-frequency = <108000000>; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index 153db59dc4b3..02cfcc716936 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -4,7 +4,7 @@ * * (C) Copyright 2014 - 2021, Xilinx, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -118,6 +118,7 @@ }; zynqmp_ipi: zynqmp_ipi { + bootph-all; compatible = "xlnx,zynqmp-ipi-mailbox"; interrupt-parent = <&gic>; interrupts = <0 35 4>; @@ -126,7 +127,8 @@ #size-cells = <2>; ranges; - ipi_mailbox_pmu1: mailbox@ff990400 { + ipi_mailbox_pmu1: mailbox@ff9905c0 { + bootph-all; reg = <0x0 0xff9905c0 0x0 0x20>, <0x0 0xff9905e0 0x0 0x20>, <0x0 0xff990e80 0x0 0x20>, @@ -143,6 +145,7 @@ dcc: dcc { compatible = "arm,dcc"; status = "disabled"; + bootph-all; }; pmu { @@ -152,6 +155,10 @@ <0 144 4>, <0 145 4>, <0 146 4>; + interrupt-affinity = <&cpu0>, + <&cpu1>, + <&cpu2>, + <&cpu3>; }; psci { @@ -164,8 +171,10 @@ compatible = "xlnx,zynqmp-firmware"; #power-domain-cells = <1>; method = "smc"; + bootph-all; zynqmp_power: zynqmp-power { + bootph-all; compatible = "xlnx,zynqmp-power"; interrupt-parent = <&gic>; interrupts = <0 35 4>; @@ -245,6 +254,7 @@ amba: axi { compatible = "simple-bus"; + bootph-all; #address-cells = <2>; #size-cells = <2>; ranges; @@ -400,7 +410,6 @@ gic: interrupt-controller@f9010000 { compatible = "arm,gic-400"; - #address-cells = <0>; #interrupt-cells = <3>; reg = <0x0 0xf9010000 0x0 0x10000>, <0x0 0xf9020000 0x0 0x20000>, @@ -411,6 +420,18 @@ interrupts = <1 9 0xf04>; }; + gpu: gpu@fd4b0000 { + status = "disabled"; + compatible = "xlnx,zynqmp-mali", "arm,mali-400"; + reg = <0x0 0xfd4b0000 0x0 0x10000>; + interrupt-parent = <&gic>; + interrupts = <0 132 4>, <0 132 4>, <0 132 4>, + <0 132 4>, <0 132 4>, <0 132 4>; + interrupt-names = "gp", "gpmmu", "pp0", "ppmmu0", "pp1", "ppmmu1"; + clock-names = "bus", "core"; + power-domains = <&zynqmp_firmware PD_GPU>; + }; + /* LPDDMA default allows only secured access. inorder to enable * These dma channels, Users should ensure that these dma * Channels are allowed for non secure access. @@ -602,7 +623,6 @@ gpio: gpio@ff0a0000 { compatible = "xlnx,zynqmp-gpio-1.0"; status = "disabled"; - #address-cells = <0>; #gpio-cells = <0x2>; gpio-controller; interrupt-parent = <&gic>; @@ -674,6 +694,7 @@ }; qspi: spi@ff0f0000 { + bootph-all; compatible = "xlnx,zynqmp-qspi-1.0"; status = "disabled"; clock-names = "ref_clk", "pclk"; @@ -720,6 +741,7 @@ }; sdhci0: mmc@ff160000 { + bootph-all; compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a"; status = "disabled"; interrupt-parent = <&gic>; @@ -730,9 +752,11 @@ #clock-cells = <1>; clock-output-names = "clk_out_sd0", "clk_in_sd0"; power-domains = <&zynqmp_firmware PD_SD_0>; + resets = <&zynqmp_reset ZYNQMP_RESET_SDIO0>; }; sdhci1: mmc@ff170000 { + bootph-all; compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a"; status = "disabled"; interrupt-parent = <&gic>; @@ -743,6 +767,7 @@ #clock-cells = <1>; clock-output-names = "clk_out_sd1", "clk_in_sd1"; power-domains = <&zynqmp_firmware PD_SD_1>; + resets = <&zynqmp_reset ZYNQMP_RESET_SDIO1>; }; smmu: iommu@fd800000 { @@ -824,6 +849,7 @@ }; uart0: serial@ff000000 { + bootph-all; compatible = "xlnx,zynqmp-uart", "cdns,uart-r1p12"; status = "disabled"; interrupt-parent = <&gic>; @@ -834,6 +860,7 @@ }; uart1: serial@ff010000 { + bootph-all; compatible = "xlnx,zynqmp-uart", "cdns,uart-r1p12"; status = "disabled"; interrupt-parent = <&gic>; @@ -928,13 +955,13 @@ #io-channel-cells = <1>; ranges = <0 0 0xffa50800 0x800>; - ams_ps: ams_ps@0 { + ams_ps: ams-ps@0 { compatible = "xlnx,zynqmp-ams-ps"; status = "disabled"; reg = <0x0 0x400>; }; - ams_pl: ams_pl@400 { + ams_pl: ams-pl@400 { compatible = "xlnx,zynqmp-ams-pl"; status = "disabled"; reg = <0x400 0x400>; @@ -955,6 +982,7 @@ }; zynqmp_dpsub: display@fd4a0000 { + bootph-all; compatible = "xlnx,zynqmp-dpsub-1.7"; status = "disabled"; reg = <0x0 0xfd4a0000 0x0 0x1000>, |