arm64: dts: qcom: sc7280: Add touchscreen to villager

This adds the touchscreen to the sc7280-herobrine-villager device
tree. Note that the touchscreen on villager actually uses the reset
line and thus we use the more specific "elan,ekth6915" compatible
which allows us to specify the reset.

The fact that villager's touchscreen uses the reset line can be
contrasted against the touchscreen for CRD/herobrine-r1. On those
boards, even though the touchscreen goes to the display, it's not
hooked up to anything there.

In order to keep the line parked on herobrine/CRD, we'll move the
pullup from the qcard.dtsi file to the specific boards. This allows us
to disable the pullup in the villager device tree since the pin is an
output.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220524134840.1.I80072b8815ac08c12af8f379a33cc2d83693dc51@changeid

4 files changed, 47 insertions, 1 deletions

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
index d92575e8ab03..e9ca6c5d24a1 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -135,6 +135,17 @@ ap_ts_pen_1v8: &i2c13 {
 	status = "okay";
 };
 
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+/*
+ * This pin goes to the display panel but then doesn't actually do anything
+ * on the panel itself (it doesn't connect to the touchscreen controller).
+ * We'll set a pullup here just to park the line.
+ */
+&ts_rst_conn {
+	bias-pull-up;
+};
+
 /* PINCTRL - BOARD-SPECIFIC */
 
 /*
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
index b69ca09d9bfb..c1647a85a371 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
@@ -128,6 +128,17 @@ ts_i2c: &i2c13 {
 	status = "okay";
 };
 
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+/*
+ * This pin goes to the display panel but then doesn't actually do anything
+ * on the panel itself (it doesn't connect to the touchscreen controller).
+ * We'll set a pullup here just to park the line.
+ */
+&ts_rst_conn {
+	bias-pull-up;
+};
+
 /* PINCTRL - BOARD-SPECIFIC */
 
 /*
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
index d3d6ffad4eff..950b69448109 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
@@ -46,6 +46,25 @@ ap_tp_i2c: &i2c0 {
 	};
 };
 
+ts_i2c: &i2c13 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@10 {
+		compatible = "elan,ekth6915";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
+
+		vcc33-supply = <&ts_avdd>;
+	};
+};
+
 &ap_sar_sensor_i2c {
 	status = "okay";
 };
@@ -81,6 +100,12 @@ ap_tp_i2c: &i2c0 {
 	status = "okay";
 };
 
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+&ts_rst_conn {
+	bias-disable;
+};
+
 /* PINCTRL - BOARD-SPECIFIC */
 
 /*
diff --git a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
index d59002d4492e..404936c6bf20 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
@@ -604,7 +604,6 @@ mos_bt_uart: &uart7 {
 	ts_rst_conn: ts-rst-conn {
 		pins = "gpio54";
 		function = "gpio";
-		bias-pull-up;
 		drive-strength = <2>;
 	};
 };