summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath
diff options
context:
space:
mode:
authorChristian Lamparter <chunkeey@gmail.com>2019-07-05 19:53:13 +0200
committerKalle Valo <kvalo@codeaurora.org>2019-09-04 09:12:35 +0300
commit5a4f2040fd07a9ec1dcd9d2601150da99565815f (patch)
treebc10c00326ac3d4ea896fa5000475f2578297f81 /drivers/net/wireless/ath
parent68092f9cf932ed894131a3b845923f4b555024ca (diff)
ath9k: add loader for AR92XX (and older) pci(e)
Atheros cards with a AR92XX generation (and older) chip usually store their pci(e) initialization vectors on an external eeprom chip. However these chips technically don't need the eeprom chip attached, the AR9280 Datasheet in section "6.1.2 DEVICE_ID" describes that "... if the EEPROM content is not valid, a value of 0xFF1C returns when read from the register". So, they will show up on the system's pci bus. However in that state, ath9k can't load, since it relies on having the correct pci-id, otherwise it doesn't know what chip it actually is. This happens on many embedded devices like routers and accesspoint since they want to keep the BOM low and store the pci(e) initialization vectors together with the calibration data on the system's FLASH, which is out of reach of the ath9k chip. Furthermore, Some devices (like the Cisco Meraki Z1 Cloud Managed Teleworker Gateway) need to be able to initialize the PCIe wifi device. Normally, this should be done as a pci quirk during the early stages of booting linux. However, this isn't possible for devices which have the init code for the Atheros chip stored on NAND in an UBI volume. Hence, this module can be used to initialize the chip when the user-space is ready to extract the init code. Martin Blumenstingl prodived the following fixes: owl-loader: add support for OWL emulation PCI devices owl-loader: don't re-scan the bus when ath9k_pci_fixup failed owl-loader: use dev_* instead of pr_* logging functions owl-loader: auto-generate the eeprom filename as fallback owl-loader: add a debug message when swapping the eeprom data owl-loader: add missing newlines in log messages Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Diffstat (limited to 'drivers/net/wireless/ath')
-rw-r--r--drivers/net/wireless/ath/ath9k/Kconfig16
-rw-r--r--drivers/net/wireless/ath/ath9k/Makefile2
-rw-r--r--drivers/net/wireless/ath/ath9k/ath9k_pci_owl_loader.c215
3 files changed, 233 insertions, 0 deletions
diff --git a/drivers/net/wireless/ath/ath9k/Kconfig b/drivers/net/wireless/ath/ath9k/Kconfig
index 5601cfd6a293..2d1247f61297 100644
--- a/drivers/net/wireless/ath/ath9k/Kconfig
+++ b/drivers/net/wireless/ath/ath9k/Kconfig
@@ -157,6 +157,22 @@ config ATH9K_PCOEM
depends on ATH9K
default y
+config ATH9K_PCI_NO_EEPROM
+ tristate "Atheros ath9k pci loader for EEPROM-less chips"
+ depends on ATH9K_PCI
+ default n
+ help
+ This separate driver provides a loader in order to support the
+ AR500X to AR92XX-generation of ath9k PCI(e) WiFi chips, which have
+ their initialization data (which contains the real PCI Device ID
+ that ath9k will need) stored together with the calibration data out
+ of reach for the ath9k chip.
+
+ These devices are usually various network appliances, routers or
+ access Points and such.
+
+ If unsure say N.
+
config ATH9K_HTC
tristate "Atheros HTC based wireless cards support"
depends on USB && MAC80211
diff --git a/drivers/net/wireless/ath/ath9k/Makefile b/drivers/net/wireless/ath/ath9k/Makefile
index 15af0a836925..eff94bcd1f0a 100644
--- a/drivers/net/wireless/ath/ath9k/Makefile
+++ b/drivers/net/wireless/ath/ath9k/Makefile
@@ -77,3 +77,5 @@ ath9k_htc-y += htc_hst.o \
ath9k_htc-$(CONFIG_ATH9K_HTC_DEBUGFS) += htc_drv_debug.o
obj-$(CONFIG_ATH9K_HTC) += ath9k_htc.o
+
+obj-$(CONFIG_ATH9K_PCI_NO_EEPROM) += ath9k_pci_owl_loader.o
diff --git a/drivers/net/wireless/ath/ath9k/ath9k_pci_owl_loader.c b/drivers/net/wireless/ath/ath9k/ath9k_pci_owl_loader.c
new file mode 100644
index 000000000000..159490f5a111
--- /dev/null
+++ b/drivers/net/wireless/ath/ath9k/ath9k_pci_owl_loader.c
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: ISC
+/* Initialize Owl Emulation Devices
+ *
+ * Copyright (C) 2016 Christian Lamparter <chunkeey@gmail.com>
+ * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ *
+ * Some devices (like the Cisco Meraki Z1 Cloud Managed Teleworker Gateway)
+ * need to be able to initialize the PCIe wifi device. Normally, this is done
+ * during the early stages as a pci quirk.
+ * However, this isn't possible for devices which have the init code for the
+ * Atheros chip stored on UBI Volume on NAND. Hence, this module can be used to
+ * initialize the chip when the user-space is ready to extract the init code.
+ */
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/completion.h>
+#include <linux/etherdevice.h>
+#include <linux/firmware.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+
+struct owl_ctx {
+ struct completion eeprom_load;
+};
+
+#define EEPROM_FILENAME_LEN 100
+
+#define AR5416_EEPROM_MAGIC 0xa55a
+
+static int ath9k_pci_fixup(struct pci_dev *pdev, const u16 *cal_data,
+ size_t cal_len)
+{
+ void __iomem *mem;
+ const void *cal_end = (void *)cal_data + cal_len;
+ const struct {
+ u16 reg;
+ u16 low_val;
+ u16 high_val;
+ } __packed * data;
+ u16 cmd;
+ u32 bar0;
+ bool swap_needed = false;
+
+ if (*cal_data != AR5416_EEPROM_MAGIC) {
+ if (*cal_data != swab16(AR5416_EEPROM_MAGIC)) {
+ dev_err(&pdev->dev, "invalid calibration data\n");
+ return -EINVAL;
+ }
+
+ dev_dbg(&pdev->dev, "calibration data needs swapping\n");
+ swap_needed = true;
+ }
+
+ dev_info(&pdev->dev, "fixup device configuration\n");
+
+ mem = pcim_iomap(pdev, 0, 0);
+ if (!mem) {
+ dev_err(&pdev->dev, "ioremap error\n");
+ return -EINVAL;
+ }
+
+ pci_read_config_dword(pdev, PCI_BASE_ADDRESS_0, &bar0);
+ pci_write_config_dword(pdev, PCI_BASE_ADDRESS_0,
+ pci_resource_start(pdev, 0));
+ pci_read_config_word(pdev, PCI_COMMAND, &cmd);
+ cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pci_write_config_word(pdev, PCI_COMMAND, cmd);
+
+ /* set pointer to first reg address */
+ for (data = (const void *)(cal_data + 3);
+ (const void *)data <= cal_end && data->reg != (u16)~0;
+ data++) {
+ u32 val;
+ u16 reg;
+
+ reg = data->reg;
+ val = data->low_val;
+ val |= ((u32)data->high_val) << 16;
+
+ if (swap_needed) {
+ reg = swab16(reg);
+ val = swahb32(val);
+ }
+
+ __raw_writel(val, mem + reg);
+ usleep_range(100, 120);
+ }
+
+ pci_read_config_word(pdev, PCI_COMMAND, &cmd);
+ cmd &= ~(PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
+ pci_write_config_word(pdev, PCI_COMMAND, cmd);
+
+ pci_write_config_dword(pdev, PCI_BASE_ADDRESS_0, bar0);
+ pcim_iounmap(pdev, mem);
+
+ pci_disable_device(pdev);
+
+ return 0;
+}
+
+static void owl_fw_cb(const struct firmware *fw, void *context)
+{
+ struct pci_dev *pdev = (struct pci_dev *)context;
+ struct owl_ctx *ctx = (struct owl_ctx *)pci_get_drvdata(pdev);
+ struct pci_bus *bus;
+
+ complete(&ctx->eeprom_load);
+
+ if (!fw) {
+ dev_err(&pdev->dev, "no eeprom data received.\n");
+ goto release;
+ }
+
+ /* also note that we are doing *u16 operations on the file */
+ if (fw->size > 4096 || fw->size < 0x200 || (fw->size & 1) == 1) {
+ dev_err(&pdev->dev, "eeprom file has an invalid size.\n");
+ goto release;
+ }
+
+ if (ath9k_pci_fixup(pdev, (const u16 *)fw->data, fw->size))
+ goto release;
+
+ pci_lock_rescan_remove();
+ bus = pdev->bus;
+ pci_stop_and_remove_bus_device(pdev);
+ /* the device should come back with the proper
+ * ProductId. But we have to initiate a rescan.
+ */
+ pci_rescan_bus(bus);
+ pci_unlock_rescan_remove();
+
+release:
+ release_firmware(fw);
+}
+
+static const char *owl_get_eeprom_name(struct pci_dev *pdev)
+{
+ struct device *dev = &pdev->dev;
+ char *eeprom_name;
+
+ dev_dbg(dev, "using auto-generated eeprom filename\n");
+
+ eeprom_name = devm_kzalloc(dev, EEPROM_FILENAME_LEN, GFP_KERNEL);
+ if (!eeprom_name)
+ return NULL;
+
+ /* this should match the pattern used in ath9k/init.c */
+ scnprintf(eeprom_name, EEPROM_FILENAME_LEN, "ath9k-eeprom-pci-%s.bin",
+ dev_name(dev));
+
+ return eeprom_name;
+}
+
+static int owl_probe(struct pci_dev *pdev,
+ const struct pci_device_id *id)
+{
+ struct owl_ctx *ctx;
+ const char *eeprom_name;
+ int err = 0;
+
+ if (pcim_enable_device(pdev))
+ return -EIO;
+
+ pcim_pin_device(pdev);
+
+ eeprom_name = owl_get_eeprom_name(pdev);
+ if (!eeprom_name) {
+ dev_err(&pdev->dev, "no eeprom filename found.\n");
+ return -ENODEV;
+ }
+
+ ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ init_completion(&ctx->eeprom_load);
+
+ pci_set_drvdata(pdev, ctx);
+ err = request_firmware_nowait(THIS_MODULE, true, eeprom_name,
+ &pdev->dev, GFP_KERNEL, pdev, owl_fw_cb);
+ if (err)
+ dev_err(&pdev->dev, "failed to request caldata (%d).\n", err);
+
+ return err;
+}
+
+static void owl_remove(struct pci_dev *pdev)
+{
+ struct owl_ctx *ctx = pci_get_drvdata(pdev);
+
+ if (ctx) {
+ wait_for_completion(&ctx->eeprom_load);
+ pci_set_drvdata(pdev, NULL);
+ }
+}
+
+static const struct pci_device_id owl_pci_table[] = {
+ { PCI_VDEVICE(ATHEROS, 0xff1c) }, /* PCIe */
+ { PCI_VDEVICE(ATHEROS, 0xff1d) }, /* PCI */
+ { },
+};
+MODULE_DEVICE_TABLE(pci, owl_pci_table);
+
+static struct pci_driver owl_driver = {
+ .name = KBUILD_MODNAME,
+ .id_table = owl_pci_table,
+ .probe = owl_probe,
+ .remove = owl_remove,
+};
+module_pci_driver(owl_driver);
+MODULE_AUTHOR("Christian Lamparter <chunkeey@gmail.com>");
+MODULE_DESCRIPTION("External EEPROM data loader for Atheros AR500X to AR92XX");
+MODULE_LICENSE("Dual BSD/GPL");