Merge branch 'at803x-sfp-fiber'

Robert Hancock says:

====================
at803x fiber/SFP support

Add support for 1000Base-X fiber modes to the at803x PHY driver, as
well as support for connecting a downstream SFP cage.

Changes since v3:
-Renamed some constants with OHM suffix for clarity

Changes since v2:
-fixed tabs/spaces issue in one patch

Changes since v1:
-moved page selection to config_init so it is handled properly
after suspend/resume
-added explicit check for empty sfp_support bitmask
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 126 insertions, 20 deletions

diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 5b6c0d120e09..f504fe536fe4 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -19,6 +19,8 @@
 #include <linux/regulator/of_regulator.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/consumer.h>
+#include <linux/phylink.h>
+#include <linux/sfp.h>
 #include <dt-bindings/net/qca-ar803x.h>
 
 #define AT803X_SPECIFIC_FUNCTION_CONTROL	0x10
@@ -51,6 +53,8 @@
 #define AT803X_INTR_ENABLE_PAGE_RECEIVED	BIT(12)
 #define AT803X_INTR_ENABLE_LINK_FAIL		BIT(11)
 #define AT803X_INTR_ENABLE_LINK_SUCCESS		BIT(10)
+#define AT803X_INTR_ENABLE_LINK_FAIL_BX		BIT(8)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX	BIT(7)
 #define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE	BIT(5)
 #define AT803X_INTR_ENABLE_POLARITY_CHANGED	BIT(1)
 #define AT803X_INTR_ENABLE_WOL			BIT(0)
@@ -85,7 +89,17 @@
 #define AT803X_DEBUG_DATA			0x1E
 
 #define AT803X_MODE_CFG_MASK			0x0F
-#define AT803X_MODE_CFG_SGMII			0x01
+#define AT803X_MODE_CFG_BASET_RGMII		0x00
+#define AT803X_MODE_CFG_BASET_SGMII		0x01
+#define AT803X_MODE_CFG_BX1000_RGMII_50OHM	0x02
+#define AT803X_MODE_CFG_BX1000_RGMII_75OHM	0x03
+#define AT803X_MODE_CFG_BX1000_CONV_50OHM	0x04
+#define AT803X_MODE_CFG_BX1000_CONV_75OHM	0x05
+#define AT803X_MODE_CFG_FX100_RGMII_50OHM	0x06
+#define AT803X_MODE_CFG_FX100_CONV_50OHM	0x07
+#define AT803X_MODE_CFG_RGMII_AUTO_MDET		0x0B
+#define AT803X_MODE_CFG_FX100_RGMII_75OHM	0x0E
+#define AT803X_MODE_CFG_FX100_CONV_75OHM	0x0F
 
 #define AT803X_PSSR				0x11	/*PHY-Specific Status Register*/
 #define AT803X_PSSR_MR_AN_COMPLETE		0x0200
@@ -283,6 +297,8 @@ struct at803x_priv {
 	u16 clk_25m_mask;
 	u8 smarteee_lpi_tw_1g;
 	u8 smarteee_lpi_tw_100m;
+	bool is_fiber;
+	bool is_1000basex;
 	struct regulator_dev *vddio_rdev;
 	struct regulator_dev *vddh_rdev;
 	struct regulator *vddio;
@@ -650,6 +666,55 @@ static int at8031_register_regulators(struct phy_device *phydev)
 	return 0;
 }
 
+static int at803x_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
+{
+	struct phy_device *phydev = upstream;
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(phy_support);
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(sfp_support);
+	phy_interface_t iface;
+
+	linkmode_zero(phy_support);
+	phylink_set(phy_support, 1000baseX_Full);
+	phylink_set(phy_support, 1000baseT_Full);
+	phylink_set(phy_support, Autoneg);
+	phylink_set(phy_support, Pause);
+	phylink_set(phy_support, Asym_Pause);
+
+	linkmode_zero(sfp_support);
+	sfp_parse_support(phydev->sfp_bus, id, sfp_support);
+	/* Some modules support 10G modes as well as others we support.
+	 * Mask out non-supported modes so the correct interface is picked.
+	 */
+	linkmode_and(sfp_support, phy_support, sfp_support);
+
+	if (linkmode_empty(sfp_support)) {
+		dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n");
+		return -EINVAL;
+	}
+
+	iface = sfp_select_interface(phydev->sfp_bus, sfp_support);
+
+	/* Only 1000Base-X is supported by AR8031/8033 as the downstream SerDes
+	 * interface for use with SFP modules.
+	 * However, some copper modules detected as having a preferred SGMII
+	 * interface do default to and function in 1000Base-X mode, so just
+	 * print a warning and allow such modules, as they may have some chance
+	 * of working.
+	 */
+	if (iface == PHY_INTERFACE_MODE_SGMII)
+		dev_warn(&phydev->mdio.dev, "module may not function if 1000Base-X not supported\n");
+	else if (iface != PHY_INTERFACE_MODE_1000BASEX)
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct sfp_upstream_ops at803x_sfp_ops = {
+	.attach = phy_sfp_attach,
+	.detach = phy_sfp_detach,
+	.module_insert = at803x_sfp_insert,
+};
+
 static int at803x_parse_dt(struct phy_device *phydev)
 {
 	struct device_node *node = phydev->mdio.dev.of_node;
@@ -757,6 +822,11 @@ static int at803x_parse_dt(struct phy_device *phydev)
 			phydev_err(phydev, "failed to get VDDIO regulator\n");
 			return PTR_ERR(priv->vddio);
 		}
+
+		/* Only AR8031/8033 support 1000Base-X for SFP modules */
+		ret = phy_sfp_probe(phydev, &at803x_sfp_ops);
+		if (ret < 0)
+			return ret;
 	}
 
 	return 0;
@@ -784,16 +854,24 @@ static int at803x_probe(struct phy_device *phydev)
 			return ret;
 	}
 
-	/* Some bootloaders leave the fiber page selected.
-	 * Switch to the copper page, as otherwise we read
-	 * the PHY capabilities from the fiber side.
-	 */
 	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
-		phy_lock_mdio_bus(phydev);
-		ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
-		phy_unlock_mdio_bus(phydev);
-		if (ret)
+		int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
+		int mode_cfg;
+
+		if (ccr < 0)
 			goto err;
+		mode_cfg = ccr & AT803X_MODE_CFG_MASK;
+
+		switch (mode_cfg) {
+		case AT803X_MODE_CFG_BX1000_RGMII_50OHM:
+		case AT803X_MODE_CFG_BX1000_RGMII_75OHM:
+			priv->is_1000basex = true;
+			fallthrough;
+		case AT803X_MODE_CFG_FX100_RGMII_50OHM:
+		case AT803X_MODE_CFG_FX100_RGMII_75OHM:
+			priv->is_fiber = true;
+			break;
+		}
 	}
 
 	return 0;
@@ -815,6 +893,7 @@ static void at803x_remove(struct phy_device *phydev)
 
 static int at803x_get_features(struct phy_device *phydev)
 {
+	struct at803x_priv *priv = phydev->priv;
 	int err;
 
 	err = genphy_read_abilities(phydev);
@@ -841,12 +920,13 @@ static int at803x_get_features(struct phy_device *phydev)
 	 * As a result of that, ESTATUS_1000_XFULL is set
 	 * to 1 even when operating in copper TP mode.
 	 *
-	 * Remove this mode from the supported link modes,
-	 * as this driver currently only supports copper
-	 * operation.
+	 * Remove this mode from the supported link modes
+	 * when not operating in 1000BaseX mode.
 	 */
-	linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
-			   phydev->supported);
+	if (!priv->is_1000basex)
+		linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+				   phydev->supported);
+
 	return 0;
 }
 
@@ -910,8 +990,27 @@ static int at8031_pll_config(struct phy_device *phydev)
 
 static int at803x_config_init(struct phy_device *phydev)
 {
+	struct at803x_priv *priv = phydev->priv;
 	int ret;
 
+	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
+		/* Some bootloaders leave the fiber page selected.
+		 * Switch to the appropriate page (fiber or copper), as otherwise we
+		 * read the PHY capabilities from the wrong page.
+		 */
+		phy_lock_mdio_bus(phydev);
+		ret = at803x_write_page(phydev,
+					priv->is_fiber ? AT803X_PAGE_FIBER :
+							 AT803X_PAGE_COPPER);
+		phy_unlock_mdio_bus(phydev);
+		if (ret)
+			return ret;
+
+		ret = at8031_pll_config(phydev);
+		if (ret < 0)
+			return ret;
+	}
+
 	/* The RX and TX delay default is:
 	 *   after HW reset: RX delay enabled and TX delay disabled
 	 *   after SW reset: RX delay enabled, while TX delay retains the
@@ -941,12 +1040,6 @@ static int at803x_config_init(struct phy_device *phydev)
 	if (ret < 0)
 		return ret;
 
-	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
-		ret = at8031_pll_config(phydev);
-		if (ret < 0)
-			return ret;
-	}
-
 	/* Ar803x extended next page bit is enabled by default. Cisco
 	 * multigig switches read this bit and attempt to negotiate 10Gbps
 	 * rates even if the next page bit is disabled. This is incorrect
@@ -967,6 +1060,7 @@ static int at803x_ack_interrupt(struct phy_device *phydev)
 
 static int at803x_config_intr(struct phy_device *phydev)
 {
+	struct at803x_priv *priv = phydev->priv;
 	int err;
 	int value;
 
@@ -983,6 +1077,10 @@ static int at803x_config_intr(struct phy_device *phydev)
 		value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
 		value |= AT803X_INTR_ENABLE_LINK_FAIL;
 		value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
+		if (priv->is_fiber) {
+			value |= AT803X_INTR_ENABLE_LINK_FAIL_BX;
+			value |= AT803X_INTR_ENABLE_LINK_SUCCESS_BX;
+		}
 
 		err = phy_write(phydev, AT803X_INTR_ENABLE, value);
 	} else {
@@ -1115,8 +1213,12 @@ static int at803x_read_specific_status(struct phy_device *phydev)
 
 static int at803x_read_status(struct phy_device *phydev)
 {
+	struct at803x_priv *priv = phydev->priv;
 	int err, old_link = phydev->link;
 
+	if (priv->is_1000basex)
+		return genphy_c37_read_status(phydev);
+
 	/* Update the link, but return if there was an error */
 	err = genphy_update_link(phydev);
 	if (err)
@@ -1170,6 +1272,7 @@ static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
 
 static int at803x_config_aneg(struct phy_device *phydev)
 {
+	struct at803x_priv *priv = phydev->priv;
 	int ret;
 
 	ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
@@ -1186,6 +1289,9 @@ static int at803x_config_aneg(struct phy_device *phydev)
 			return ret;
 	}
 
+	if (priv->is_1000basex)
+		return genphy_c37_config_aneg(phydev);
+
 	/* Do not restart auto-negotiation by setting ret to 0 defautly,
 	 * when calling __genphy_config_aneg later.
 	 */