diff options
author | Linus Torvalds <torvalds@linux-foundation.org> | 2022-03-25 13:35:34 -0700 |
---|---|---|
committer | Linus Torvalds <torvalds@linux-foundation.org> | 2022-03-25 13:35:34 -0700 |
commit | e35a4a4e13c35f500a8d38e836b5e335c7515494 (patch) | |
tree | 32940f68475c16ddee8ed2933c9a4ae6e9b44265 /drivers/spi | |
parent | 8eb48fc7c54ed627a693a205570f0eceea64274c (diff) | |
parent | 6cadd424abb63120f8346a4509dc43bddc9401d3 (diff) |
Merge tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
Diffstat (limited to 'drivers/spi')
-rw-r--r-- | drivers/spi/Kconfig | 1 | ||||
-rw-r--r-- | drivers/spi/spi-cadence-quadspi.c | 10 | ||||
-rw-r--r-- | drivers/spi/spi-mem.c | 32 | ||||
-rw-r--r-- | drivers/spi/spi-mxic.c | 340 |
4 files changed, 305 insertions, 78 deletions
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 31a2cef3790c..d2815eb361c0 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -929,6 +929,7 @@ config SPI_SYNQUACER config SPI_MXIC tristate "Macronix MX25F0A SPI controller" depends on SPI_MASTER + imply MTD_NAND_ECC_MXIC help This selects the Macronix MX25F0A SPI controller driver. diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c index b808c94641fa..b0c9f62ccefb 100644 --- a/drivers/spi/spi-cadence-quadspi.c +++ b/drivers/spi/spi-cadence-quadspi.c @@ -1441,10 +1441,7 @@ static bool cqspi_supports_mem_op(struct spi_mem *mem, if (!(all_true || all_false)) return false; - if (all_true) - return spi_mem_dtr_supports_op(mem, op); - else - return spi_mem_default_supports_op(mem, op); + return spi_mem_default_supports_op(mem, op); } static int cqspi_of_get_flash_pdata(struct platform_device *pdev, @@ -1595,6 +1592,10 @@ static const struct spi_controller_mem_ops cqspi_mem_ops = { .supports_op = cqspi_supports_mem_op, }; +static const struct spi_controller_mem_caps cqspi_mem_caps = { + .dtr = true, +}; + static int cqspi_setup_flash(struct cqspi_st *cqspi) { struct platform_device *pdev = cqspi->pdev; @@ -1652,6 +1653,7 @@ static int cqspi_probe(struct platform_device *pdev) } master->mode_bits = SPI_RX_QUAD | SPI_RX_DUAL; master->mem_ops = &cqspi_mem_ops; + master->mem_caps = &cqspi_mem_caps; master->dev.of_node = pdev->dev.of_node; cqspi = spi_master_get_devdata(master); diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c index e9d83d65873b..0e8dafc62d94 100644 --- a/drivers/spi/spi-mem.c +++ b/drivers/spi/spi-mem.c @@ -160,24 +160,28 @@ static bool spi_mem_check_buswidth(struct spi_mem *mem, return true; } -bool spi_mem_dtr_supports_op(struct spi_mem *mem, - const struct spi_mem_op *op) -{ - if (op->cmd.nbytes != 2) - return false; - - return spi_mem_check_buswidth(mem, op); -} -EXPORT_SYMBOL_GPL(spi_mem_dtr_supports_op); - bool spi_mem_default_supports_op(struct spi_mem *mem, const struct spi_mem_op *op) { - if (op->cmd.dtr || op->addr.dtr || op->dummy.dtr || op->data.dtr) - return false; + struct spi_controller *ctlr = mem->spi->controller; + bool op_is_dtr = + op->cmd.dtr || op->addr.dtr || op->dummy.dtr || op->data.dtr; - if (op->cmd.nbytes != 1) - return false; + if (op_is_dtr) { + if (!spi_mem_controller_is_capable(ctlr, dtr)) + return false; + + if (op->cmd.nbytes != 2) + return false; + } else { + if (op->cmd.nbytes != 1) + return false; + } + + if (op->data.ecc) { + if (!spi_mem_controller_is_capable(ctlr, ecc)) + return false; + } return spi_mem_check_buswidth(mem, op); } diff --git a/drivers/spi/spi-mxic.c b/drivers/spi/spi-mxic.c index 45889947afed..55c092069301 100644 --- a/drivers/spi/spi-mxic.c +++ b/drivers/spi/spi-mxic.c @@ -12,6 +12,8 @@ #include <linux/io.h> #include <linux/iopoll.h> #include <linux/module.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand-ecc-mxic.h> #include <linux/platform_device.h> #include <linux/pm_runtime.h> #include <linux/spi/spi.h> @@ -167,11 +169,23 @@ #define HW_TEST(x) (0xe0 + ((x) * 4)) struct mxic_spi { + struct device *dev; struct clk *ps_clk; struct clk *send_clk; struct clk *send_dly_clk; void __iomem *regs; u32 cur_speed_hz; + struct { + void __iomem *map; + dma_addr_t dma; + size_t size; + } linear; + + struct { + bool use_pipelined_conf; + struct nand_ecc_engine *pipelined_engine; + void *ctx; + } ecc; }; static int mxic_spi_clk_enable(struct mxic_spi *mxic) @@ -280,6 +294,51 @@ static void mxic_spi_hw_init(struct mxic_spi *mxic) mxic->regs + HC_CFG); } +static u32 mxic_spi_prep_hc_cfg(struct spi_device *spi, u32 flags) +{ + int nio = 1; + + if (spi->mode & (SPI_TX_OCTAL | SPI_RX_OCTAL)) + nio = 8; + else if (spi->mode & (SPI_TX_QUAD | SPI_RX_QUAD)) + nio = 4; + else if (spi->mode & (SPI_TX_DUAL | SPI_RX_DUAL)) + nio = 2; + + return flags | HC_CFG_NIO(nio) | + HC_CFG_TYPE(spi->chip_select, HC_CFG_TYPE_SPI_NOR) | + HC_CFG_SLV_ACT(spi->chip_select) | HC_CFG_IDLE_SIO_LVL(1); +} + +static u32 mxic_spi_mem_prep_op_cfg(const struct spi_mem_op *op, + unsigned int data_len) +{ + u32 cfg = OP_CMD_BYTES(op->cmd.nbytes) | + OP_CMD_BUSW(fls(op->cmd.buswidth) - 1) | + (op->cmd.dtr ? OP_CMD_DDR : 0); + + if (op->addr.nbytes) + cfg |= OP_ADDR_BYTES(op->addr.nbytes) | + OP_ADDR_BUSW(fls(op->addr.buswidth) - 1) | + (op->addr.dtr ? OP_ADDR_DDR : 0); + + if (op->dummy.nbytes) + cfg |= OP_DUMMY_CYC(op->dummy.nbytes); + + /* Direct mapping data.nbytes field is not populated */ + if (data_len) { + cfg |= OP_DATA_BUSW(fls(op->data.buswidth) - 1) | + (op->data.dtr ? OP_DATA_DDR : 0); + if (op->data.dir == SPI_MEM_DATA_IN) { + cfg |= OP_READ; + if (op->data.dtr) + cfg |= OP_DQS_EN; + } + } + + return cfg; +} + static int mxic_spi_data_xfer(struct mxic_spi *mxic, const void *txbuf, void *rxbuf, unsigned int len) { @@ -304,25 +363,21 @@ static int mxic_spi_data_xfer(struct mxic_spi *mxic, const void *txbuf, writel(data, mxic->regs + TXD(nbytes % 4)); + ret = readl_poll_timeout(mxic->regs + INT_STS, sts, + sts & INT_TX_EMPTY, 0, USEC_PER_SEC); + if (ret) + return ret; + + ret = readl_poll_timeout(mxic->regs + INT_STS, sts, + sts & INT_RX_NOT_EMPTY, 0, + USEC_PER_SEC); + if (ret) + return ret; + + data = readl(mxic->regs + RXD); if (rxbuf) { - ret = readl_poll_timeout(mxic->regs + INT_STS, sts, - sts & INT_TX_EMPTY, 0, - USEC_PER_SEC); - if (ret) - return ret; - - ret = readl_poll_timeout(mxic->regs + INT_STS, sts, - sts & INT_RX_NOT_EMPTY, 0, - USEC_PER_SEC); - if (ret) - return ret; - - data = readl(mxic->regs + RXD); data >>= (8 * (4 - nbytes)); memcpy(rxbuf + pos, &data, nbytes); - WARN_ON(readl(mxic->regs + INT_STS) & INT_RX_NOT_EMPTY); - } else { - readl(mxic->regs + RXD); } WARN_ON(readl(mxic->regs + INT_STS) & INT_RX_NOT_EMPTY); @@ -332,11 +387,96 @@ static int mxic_spi_data_xfer(struct mxic_spi *mxic, const void *txbuf, return 0; } +static ssize_t mxic_spi_mem_dirmap_read(struct spi_mem_dirmap_desc *desc, + u64 offs, size_t len, void *buf) +{ + struct mxic_spi *mxic = spi_master_get_devdata(desc->mem->spi->master); + int ret; + u32 sts; + + if (WARN_ON(offs + desc->info.offset + len > U32_MAX)) + return -EINVAL; + + writel(mxic_spi_prep_hc_cfg(desc->mem->spi, 0), mxic->regs + HC_CFG); + + writel(mxic_spi_mem_prep_op_cfg(&desc->info.op_tmpl, len), + mxic->regs + LRD_CFG); + writel(desc->info.offset + offs, mxic->regs + LRD_ADDR); + len = min_t(size_t, len, mxic->linear.size); + writel(len, mxic->regs + LRD_RANGE); + writel(LMODE_CMD0(desc->info.op_tmpl.cmd.opcode) | + LMODE_SLV_ACT(desc->mem->spi->chip_select) | + LMODE_EN, + mxic->regs + LRD_CTRL); + + if (mxic->ecc.use_pipelined_conf && desc->info.op_tmpl.data.ecc) { + ret = mxic_ecc_process_data_pipelined(mxic->ecc.pipelined_engine, + NAND_PAGE_READ, + mxic->linear.dma + offs); + if (ret) + return ret; + } else { + memcpy_fromio(buf, mxic->linear.map, len); + } + + writel(INT_LRD_DIS, mxic->regs + INT_STS); + writel(0, mxic->regs + LRD_CTRL); + + ret = readl_poll_timeout(mxic->regs + INT_STS, sts, + sts & INT_LRD_DIS, 0, USEC_PER_SEC); + if (ret) + return ret; + + return len; +} + +static ssize_t mxic_spi_mem_dirmap_write(struct spi_mem_dirmap_desc *desc, + u64 offs, size_t len, + const void *buf) +{ + struct mxic_spi *mxic = spi_master_get_devdata(desc->mem->spi->master); + u32 sts; + int ret; + + if (WARN_ON(offs + desc->info.offset + len > U32_MAX)) + return -EINVAL; + + writel(mxic_spi_prep_hc_cfg(desc->mem->spi, 0), mxic->regs + HC_CFG); + + writel(mxic_spi_mem_prep_op_cfg(&desc->info.op_tmpl, len), + mxic->regs + LWR_CFG); + writel(desc->info.offset + offs, mxic->regs + LWR_ADDR); + len = min_t(size_t, len, mxic->linear.size); + writel(len, mxic->regs + LWR_RANGE); + writel(LMODE_CMD0(desc->info.op_tmpl.cmd.opcode) | + LMODE_SLV_ACT(desc->mem->spi->chip_select) | + LMODE_EN, + mxic->regs + LWR_CTRL); + + if (mxic->ecc.use_pipelined_conf && desc->info.op_tmpl.data.ecc) { + ret = mxic_ecc_process_data_pipelined(mxic->ecc.pipelined_engine, + NAND_PAGE_WRITE, + mxic->linear.dma + offs); + if (ret) + return ret; + } else { + memcpy_toio(mxic->linear.map, buf, len); + } + + writel(INT_LWR_DIS, mxic->regs + INT_STS); + writel(0, mxic->regs + LWR_CTRL); + + ret = readl_poll_timeout(mxic->regs + INT_STS, sts, + sts & INT_LWR_DIS, 0, USEC_PER_SEC); + if (ret) + return ret; + + return len; +} + static bool mxic_spi_mem_supports_op(struct spi_mem *mem, const struct spi_mem_op *op) { - bool all_false; - if (op->data.buswidth > 8 || op->addr.buswidth > 8 || op->dummy.buswidth > 8 || op->cmd.buswidth > 8) return false; @@ -348,64 +488,43 @@ static bool mxic_spi_mem_supports_op(struct spi_mem *mem, if (op->addr.nbytes > 7) return false; - all_false = !op->cmd.dtr && !op->addr.dtr && !op->dummy.dtr && - !op->data.dtr; + return spi_mem_default_supports_op(mem, op); +} + +static int mxic_spi_mem_dirmap_create(struct spi_mem_dirmap_desc *desc) +{ + struct mxic_spi *mxic = spi_master_get_devdata(desc->mem->spi->master); - if (all_false) - return spi_mem_default_supports_op(mem, op); - else - return spi_mem_dtr_supports_op(mem, op); + if (!mxic->linear.map) + return -EINVAL; + + if (desc->info.offset + desc->info.length > U32_MAX) + return -EINVAL; + + if (!mxic_spi_mem_supports_op(desc->mem, &desc->info.op_tmpl)) + return -EOPNOTSUPP; + + return 0; } static int mxic_spi_mem_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) { struct mxic_spi *mxic = spi_master_get_devdata(mem->spi->master); - int nio = 1, i, ret; - u32 ss_ctrl; + int i, ret; u8 addr[8], cmd[2]; ret = mxic_spi_set_freq(mxic, mem->spi->max_speed_hz); if (ret) return ret; - if (mem->spi->mode & (SPI_TX_OCTAL | SPI_RX_OCTAL)) - nio = 8; - else if (mem->spi->mode & (SPI_TX_QUAD | SPI_RX_QUAD)) - nio = 4; - else if (mem->spi->mode & (SPI_TX_DUAL | SPI_RX_DUAL)) - nio = 2; - - writel(HC_CFG_NIO(nio) | - HC_CFG_TYPE(mem->spi->chip_select, HC_CFG_TYPE_SPI_NOR) | - HC_CFG_SLV_ACT(mem->spi->chip_select) | HC_CFG_IDLE_SIO_LVL(1) | - HC_CFG_MAN_CS_EN, + writel(mxic_spi_prep_hc_cfg(mem->spi, HC_CFG_MAN_CS_EN), mxic->regs + HC_CFG); - writel(HC_EN_BIT, mxic->regs + HC_EN); - - ss_ctrl = OP_CMD_BYTES(op->cmd.nbytes) | - OP_CMD_BUSW(fls(op->cmd.buswidth) - 1) | - (op->cmd.dtr ? OP_CMD_DDR : 0); - - if (op->addr.nbytes) - ss_ctrl |= OP_ADDR_BYTES(op->addr.nbytes) | - OP_ADDR_BUSW(fls(op->addr.buswidth) - 1) | - (op->addr.dtr ? OP_ADDR_DDR : 0); - - if (op->dummy.nbytes) - ss_ctrl |= OP_DUMMY_CYC(op->dummy.nbytes); - if (op->data.nbytes) { - ss_ctrl |= OP_DATA_BUSW(fls(op->data.buswidth) - 1) | - (op->data.dtr ? OP_DATA_DDR : 0); - if (op->data.dir == SPI_MEM_DATA_IN) { - ss_ctrl |= OP_READ; - if (op->data.dtr) - ss_ctrl |= OP_DQS_EN; - } - } + writel(HC_EN_BIT, mxic->regs + HC_EN); - writel(ss_ctrl, mxic->regs + SS_CTRL(mem->spi->chip_select)); + writel(mxic_spi_mem_prep_op_cfg(op, op->data.nbytes), + mxic->regs + SS_CTRL(mem->spi->chip_select)); writel(readl(mxic->regs + HC_CFG) | HC_CFG_MAN_CS_ASSERT, mxic->regs + HC_CFG); @@ -446,6 +565,14 @@ out: static const struct spi_controller_mem_ops mxic_spi_mem_ops = { .supports_op = mxic_spi_mem_supports_op, .exec_op = mxic_spi_mem_exec_op, + .dirmap_create = mxic_spi_mem_dirmap_create, + .dirmap_read = mxic_spi_mem_dirmap_read, + .dirmap_write = mxic_spi_mem_dirmap_write, +}; + +static const struct spi_controller_mem_caps mxic_spi_mem_caps = { + .dtr = true, + .ecc = true, }; static void mxic_spi_set_cs(struct spi_device *spi, bool lvl) @@ -510,6 +637,80 @@ static int mxic_spi_transfer_one(struct spi_master *master, return 0; } +/* ECC wrapper */ +static int mxic_spi_mem_ecc_init_ctx(struct nand_device *nand) +{ + struct nand_ecc_engine_ops *ops = mxic_ecc_get_pipelined_ops(); + struct mxic_spi *mxic = nand->ecc.engine->priv; + + mxic->ecc.use_pipelined_conf = true; + + return ops->init_ctx(nand); +} + +static void mxic_spi_mem_ecc_cleanup_ctx(struct nand_device *nand) +{ + struct nand_ecc_engine_ops *ops = mxic_ecc_get_pipelined_ops(); + struct mxic_spi *mxic = nand->ecc.engine->priv; + + mxic->ecc.use_pipelined_conf = false; + + ops->cleanup_ctx(nand); +} + +static int mxic_spi_mem_ecc_prepare_io_req(struct nand_device *nand, + struct nand_page_io_req *req) +{ + struct nand_ecc_engine_ops *ops = mxic_ecc_get_pipelined_ops(); + + return ops->prepare_io_req(nand, req); +} + +static int mxic_spi_mem_ecc_finish_io_req(struct nand_device *nand, + struct nand_page_io_req *req) +{ + struct nand_ecc_engine_ops *ops = mxic_ecc_get_pipelined_ops(); + + return ops->finish_io_req(nand, req); +} + +static struct nand_ecc_engine_ops mxic_spi_mem_ecc_engine_pipelined_ops = { + .init_ctx = mxic_spi_mem_ecc_init_ctx, + .cleanup_ctx = mxic_spi_mem_ecc_cleanup_ctx, + .prepare_io_req = mxic_spi_mem_ecc_prepare_io_req, + .finish_io_req = mxic_spi_mem_ecc_finish_io_req, +}; + +static void mxic_spi_mem_ecc_remove(struct mxic_spi *mxic) +{ + if (mxic->ecc.pipelined_engine) { + mxic_ecc_put_pipelined_engine(mxic->ecc.pipelined_engine); + nand_ecc_unregister_on_host_hw_engine(mxic->ecc.pipelined_engine); + } +} + +static int mxic_spi_mem_ecc_probe(struct platform_device *pdev, + struct mxic_spi *mxic) +{ + struct nand_ecc_engine *eng; + + if (!mxic_ecc_get_pipelined_ops()) + return -EOPNOTSUPP; + + eng = mxic_ecc_get_pipelined_engine(pdev); + if (IS_ERR(eng)) + return PTR_ERR(eng); + + eng->dev = &pdev->dev; + eng->integration = NAND_ECC_ENGINE_INTEGRATION_PIPELINED; + eng->ops = &mxic_spi_mem_ecc_engine_pipelined_ops; + eng->priv = mxic; + mxic->ecc.pipelined_engine = eng; + nand_ecc_register_on_host_hw_engine(eng); + + return 0; +} + static int __maybe_unused mxic_spi_runtime_suspend(struct device *dev) { struct spi_master *master = dev_get_drvdata(dev); @@ -555,6 +756,7 @@ static int mxic_spi_probe(struct platform_device *pdev) platform_set_drvdata(pdev, master); mxic = spi_master_get_devdata(master); + mxic->dev = &pdev->dev; master->dev.of_node = pdev->dev.of_node; @@ -575,11 +777,21 @@ static int mxic_spi_probe(struct platform_device *pdev) if (IS_ERR(mxic->regs)) return PTR_ERR(mxic->regs); + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dirmap"); + mxic->linear.map = devm_ioremap_resource(&pdev->dev, res); + if (!IS_ERR(mxic->linear.map)) { + mxic->linear.dma = res->start; + mxic->linear.size = resource_size(res); + } else { + mxic->linear.map = NULL; + } + pm_runtime_enable(&pdev->dev); master->auto_runtime_pm = true; master->num_chipselect = 1; master->mem_ops = &mxic_spi_mem_ops; + master->mem_caps = &mxic_spi_mem_caps; master->set_cs = mxic_spi_set_cs; master->transfer_one = mxic_spi_transfer_one; @@ -591,6 +803,12 @@ static int mxic_spi_probe(struct platform_device *pdev) mxic_spi_hw_init(mxic); + ret = mxic_spi_mem_ecc_probe(pdev, mxic); + if (ret == -EPROBE_DEFER) { + pm_runtime_disable(&pdev->dev); + return ret; + } + ret = spi_register_master(master); if (ret) { dev_err(&pdev->dev, "spi_register_master failed\n"); @@ -603,8 +821,10 @@ static int mxic_spi_probe(struct platform_device *pdev) static int mxic_spi_remove(struct platform_device *pdev) { struct spi_master *master = platform_get_drvdata(pdev); + struct mxic_spi *mxic = spi_master_get_devdata(master); pm_runtime_disable(&pdev->dev); + mxic_spi_mem_ecc_remove(mxic); spi_unregister_master(master); return 0; |