diff options
41 files changed, 1832 insertions, 229 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-adc-ad7192 b/Documentation/ABI/testing/sysfs-bus-iio-adc-ad7192 new file mode 100644 index 000000000000..7627d3be08f5 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-adc-ad7192 @@ -0,0 +1,39 @@ +What: /sys/bus/iio/devices/iio:deviceX/ac_excitation_en +KernelVersion: +Contact: linux-iio@vger.kernel.org +Description: + Reading gives the state of AC excitation. + Writing '1' enables AC excitation. + +What: /sys/bus/iio/devices/iio:deviceX/bridge_switch_en +KernelVersion: +Contact: linux-iio@vger.kernel.org +Description: + This bridge switch is used to disconnect it when there is a + need to minimize the system current consumption. + Reading gives the state of the bridge switch. + Writing '1' enables the bridge switch. + +What: /sys/bus/iio/devices/iio:deviceX/in_voltagex_sys_calibration +KernelVersion: +Contact: linux-iio@vger.kernel.org +Description: + Initiates the system calibration procedure. This is done on a + single channel at a time. Write '1' to start the calibration. + +What: /sys/bus/iio/devices/iio:deviceX/in_voltagex_sys_calibration_mode_available +KernelVersion: +Contact: linux-iio@vger.kernel.org +Description: + Reading returns a list with the possible calibration modes. + There are two available options: + "zero_scale" - calibrate to zero scale + "full_scale" - calibrate to full scale + +What: /sys/bus/iio/devices/iio:deviceX/in_voltagex_sys_calibration_mode +KernelVersion: +Contact: linux-iio@vger.kernel.org +Description: + Sets up the calibration mode used in the system calibration + procedure. Reading returns the current calibration mode. + Writing sets the system calibration mode. diff --git a/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt b/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt index f01159f20d87..cd9048cf9dcf 100644 --- a/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt @@ -5,6 +5,7 @@ Required properties: - compatible: Should be one of: * ingenic,jz4725b-adc * ingenic,jz4740-adc + * ingenic,jz4770-adc - reg: ADC controller registers location and length. - clocks: phandle to the SoC's ADC clock. - clock-names: Must be set to "adc". diff --git a/Documentation/devicetree/bindings/iio/iio-bindings.txt b/Documentation/devicetree/bindings/iio/iio-bindings.txt index 68d6f8ce063b..af33267727f4 100644 --- a/Documentation/devicetree/bindings/iio/iio-bindings.txt +++ b/Documentation/devicetree/bindings/iio/iio-bindings.txt @@ -18,12 +18,17 @@ Required properties: with a single IIO output and 1 for nodes with multiple IIO outputs. +Optional properties: +label: A symbolic name for the device. + + Example for a simple configuration with no trigger: adc: voltage-sensor@35 { compatible = "maxim,max1139"; reg = <0x35>; #io-channel-cells = <1>; + label = "voltage_feedback_group1"; }; Example for a configuration with trigger: diff --git a/Documentation/devicetree/bindings/iio/light/bh1750.txt b/Documentation/devicetree/bindings/iio/light/bh1750.txt deleted file mode 100644 index 1e7685797d7a..000000000000 --- a/Documentation/devicetree/bindings/iio/light/bh1750.txt +++ /dev/null @@ -1,18 +0,0 @@ -ROHM BH1750 - ALS, Ambient light sensor - -Required properties: - -- compatible: Must be one of: - "rohm,bh1710" - "rohm,bh1715" - "rohm,bh1721" - "rohm,bh1750" - "rohm,bh1751" -- reg: the I2C address of the sensor - -Example: - -light-sensor@23 { - compatible = "rohm,bh1750"; - reg = <0x23>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/bh1750.yaml b/Documentation/devicetree/bindings/iio/light/bh1750.yaml new file mode 100644 index 000000000000..1cc60d7ecfa0 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/bh1750.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/bh1750.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ROHM BH1750 ambient light sensor + +maintainers: + - Tomasz Duszynski <tduszyns@gmail.com> + +description: | + Ambient light sensor with an i2c interface. + +properties: + compatible: + enum: + - rohm,bh1710 + - rohm,bh1715 + - rohm,bh1721 + - rohm,bh1750 + - rohm,bh1751 + + reg: + maxItems: 1 + +required: + - compatible + - reg + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + light-sensor@23 { + compatible = "rohm,bh1750"; + reg = <0x23>; + }; + }; + +... diff --git a/MAINTAINERS b/MAINTAINERS index 8f5b4847a9e8..ef4cd6b4aa85 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -13951,6 +13951,12 @@ L: linux-serial@vger.kernel.org S: Odd Fixes F: drivers/tty/serial/rp2.* +ROHM BH1750 AMBIENT LIGHT SENSOR DRIVER +M: Tomasz Duszynski <tduszyns@gmail.com> +S: Maintained +F: drivers/iio/light/bh1750.c +F: Documentation/devicetree/bindings/iio/light/bh1750.yaml + ROHM MULTIFUNCTION BD9571MWV-M PMIC DEVICE DRIVERS M: Marek Vasut <marek.vasut+renesas@gmail.com> L: linux-kernel@vger.kernel.org diff --git a/drivers/counter/stm32-lptimer-cnt.c b/drivers/counter/stm32-lptimer-cnt.c index bbc930a5962c..28b63645c411 100644 --- a/drivers/counter/stm32-lptimer-cnt.c +++ b/drivers/counter/stm32-lptimer-cnt.c @@ -347,7 +347,7 @@ static const struct iio_chan_spec stm32_lptim_cnt_channels = { }; /** - * stm32_lptim_cnt_function - enumerates stm32 LPTimer counter & encoder modes + * enum stm32_lptim_cnt_function - enumerates LPTimer counter & encoder modes * @STM32_LPTIM_COUNTER_INCREASE: up count on IN1 rising, falling or both edges * @STM32_LPTIM_ENCODER_BOTH_EDGE: count on both edges (IN1 & IN2 quadrature) */ diff --git a/drivers/counter/stm32-timer-cnt.c b/drivers/counter/stm32-timer-cnt.c index 644ba18a72ad..b61135b63ee8 100644 --- a/drivers/counter/stm32-timer-cnt.c +++ b/drivers/counter/stm32-timer-cnt.c @@ -28,7 +28,7 @@ struct stm32_timer_cnt { }; /** - * stm32_count_function - enumerates stm32 timer counter encoder modes + * enum stm32_count_function - enumerates stm32 timer counter encoder modes * @STM32_COUNT_SLAVE_MODE_DISABLED: counts on internal clock when CEN=1 * @STM32_COUNT_ENCODER_MODE_1: counts TI1FP1 edges, depending on TI2FP2 level * @STM32_COUNT_ENCODER_MODE_2: counts TI2FP2 edges, depending on TI1FP1 level @@ -219,8 +219,8 @@ static ssize_t stm32_count_enable_write(struct counter_device *counter, if (enable) { regmap_read(priv->regmap, TIM_CR1, &cr1); - if (!(cr1 & TIM_CR1_CEN)) - clk_enable(priv->clk); + if (!(cr1 & TIM_CR1_CEN)) + clk_enable(priv->clk); regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, TIM_CR1_CEN); diff --git a/drivers/iio/adc/ad7949.c b/drivers/iio/adc/ad7949.c index ac0ffff6c5ae..5c2b3446fa4a 100644 --- a/drivers/iio/adc/ad7949.c +++ b/drivers/iio/adc/ad7949.c @@ -54,38 +54,20 @@ struct ad7949_adc_chip { u8 resolution; u16 cfg; unsigned int current_channel; - u32 buffer ____cacheline_aligned; + u16 buffer ____cacheline_aligned; }; -static bool ad7949_spi_cfg_is_read_back(struct ad7949_adc_chip *ad7949_adc) -{ - if (!(ad7949_adc->cfg & AD7949_CFG_READ_BACK)) - return true; - - return false; -} - -static int ad7949_spi_bits_per_word(struct ad7949_adc_chip *ad7949_adc) -{ - int ret = ad7949_adc->resolution; - - if (ad7949_spi_cfg_is_read_back(ad7949_adc)) - ret += AD7949_CFG_REG_SIZE_BITS; - - return ret; -} - static int ad7949_spi_write_cfg(struct ad7949_adc_chip *ad7949_adc, u16 val, u16 mask) { int ret; - int bits_per_word = ad7949_spi_bits_per_word(ad7949_adc); + int bits_per_word = ad7949_adc->resolution; int shift = bits_per_word - AD7949_CFG_REG_SIZE_BITS; struct spi_message msg; struct spi_transfer tx[] = { { .tx_buf = &ad7949_adc->buffer, - .len = 4, + .len = 2, .bits_per_word = bits_per_word, }, }; @@ -107,13 +89,13 @@ static int ad7949_spi_read_channel(struct ad7949_adc_chip *ad7949_adc, int *val, unsigned int channel) { int ret; - int bits_per_word = ad7949_spi_bits_per_word(ad7949_adc); + int bits_per_word = ad7949_adc->resolution; int mask = GENMASK(ad7949_adc->resolution, 0); struct spi_message msg; struct spi_transfer tx[] = { { .rx_buf = &ad7949_adc->buffer, - .len = 4, + .len = 2, .bits_per_word = bits_per_word, }, }; @@ -138,10 +120,7 @@ static int ad7949_spi_read_channel(struct ad7949_adc_chip *ad7949_adc, int *val, ad7949_adc->current_channel = channel; - if (ad7949_spi_cfg_is_read_back(ad7949_adc)) - *val = (ad7949_adc->buffer >> AD7949_CFG_REG_SIZE_BITS) & mask; - else - *val = ad7949_adc->buffer & mask; + *val = ad7949_adc->buffer & mask; return 0; } diff --git a/drivers/iio/adc/ad_sigma_delta.c b/drivers/iio/adc/ad_sigma_delta.c index 2640b75fb774..8ba90486c787 100644 --- a/drivers/iio/adc/ad_sigma_delta.c +++ b/drivers/iio/adc/ad_sigma_delta.c @@ -205,7 +205,7 @@ int ad_sd_reset(struct ad_sigma_delta *sigma_delta, } EXPORT_SYMBOL_GPL(ad_sd_reset); -static int ad_sd_calibrate(struct ad_sigma_delta *sigma_delta, +int ad_sd_calibrate(struct ad_sigma_delta *sigma_delta, unsigned int mode, unsigned int channel) { int ret; @@ -242,6 +242,7 @@ out: return ret; } +EXPORT_SYMBOL_GPL(ad_sd_calibrate); /** * ad_sd_calibrate_all() - Performs channel calibration diff --git a/drivers/iio/adc/ingenic-adc.c b/drivers/iio/adc/ingenic-adc.c index e234970b7150..7a53c2f8d438 100644 --- a/drivers/iio/adc/ingenic-adc.c +++ b/drivers/iio/adc/ingenic-adc.c @@ -25,9 +25,13 @@ #define JZ_ADC_REG_ADSDAT 0x20 #define JZ_ADC_REG_ADCLK 0x28 +#define JZ_ADC_REG_ENABLE_PD BIT(7) +#define JZ_ADC_REG_CFG_AUX_MD (BIT(0) | BIT(1)) #define JZ_ADC_REG_CFG_BAT_MD BIT(4) #define JZ_ADC_REG_ADCLK_CLKDIV_LSB 0 -#define JZ_ADC_REG_ADCLK_CLKDIV10US_LSB 16 +#define JZ4725B_ADC_REG_ADCLK_CLKDIV10US_LSB 16 +#define JZ4770_ADC_REG_ADCLK_CLKDIV10US_LSB 8 +#define JZ4770_ADC_REG_ADCLK_CLKDIVMS_LSB 16 #define JZ_ADC_AUX_VREF 3300 #define JZ_ADC_AUX_VREF_BITS 12 @@ -37,6 +41,8 @@ #define JZ4725B_ADC_BATTERY_HIGH_VREF_BITS 10 #define JZ4740_ADC_BATTERY_HIGH_VREF (7500 * 0.986) #define JZ4740_ADC_BATTERY_HIGH_VREF_BITS 12 +#define JZ4770_ADC_BATTERY_VREF 6600 +#define JZ4770_ADC_BATTERY_VREF_BITS 12 struct ingenic_adc; @@ -47,6 +53,8 @@ struct ingenic_adc_soc_data { size_t battery_raw_avail_size; const int *battery_scale_avail; size_t battery_scale_avail_size; + unsigned int battery_vref_mode: 1; + unsigned int has_aux2: 1; int (*init_clk_div)(struct device *dev, struct ingenic_adc *adc); }; @@ -54,6 +62,7 @@ struct ingenic_adc { void __iomem *base; struct clk *clk; struct mutex lock; + struct mutex aux_lock; const struct ingenic_adc_soc_data *soc_data; bool low_vref_mode; }; @@ -120,6 +129,8 @@ static int ingenic_adc_write_raw(struct iio_dev *iio_dev, case IIO_CHAN_INFO_SCALE: switch (chan->channel) { case INGENIC_ADC_BATTERY: + if (!adc->soc_data->battery_vref_mode) + return -EINVAL; if (val > JZ_ADC_BATTERY_LOW_VREF) { ingenic_adc_set_config(adc, JZ_ADC_REG_CFG_BAT_MD, @@ -158,6 +169,14 @@ static const int jz4740_adc_battery_scale_avail[] = { JZ_ADC_BATTERY_LOW_VREF, JZ_ADC_BATTERY_LOW_VREF_BITS, }; +static const int jz4770_adc_battery_raw_avail[] = { + 0, 1, (1 << JZ4770_ADC_BATTERY_VREF_BITS) - 1, +}; + +static const int jz4770_adc_battery_scale_avail[] = { + JZ4770_ADC_BATTERY_VREF, JZ4770_ADC_BATTERY_VREF_BITS, +}; + static int jz4725b_adc_init_clk_div(struct device *dev, struct ingenic_adc *adc) { struct clk *parent_clk; @@ -187,7 +206,45 @@ static int jz4725b_adc_init_clk_div(struct device *dev, struct ingenic_adc *adc) /* We also need a divider that produces a 10us clock. */ div_10us = DIV_ROUND_UP(rate, 100000); - writel(((div_10us - 1) << JZ_ADC_REG_ADCLK_CLKDIV10US_LSB) | + writel(((div_10us - 1) << JZ4725B_ADC_REG_ADCLK_CLKDIV10US_LSB) | + (div_main - 1) << JZ_ADC_REG_ADCLK_CLKDIV_LSB, + adc->base + JZ_ADC_REG_ADCLK); + + return 0; +} + +static int jz4770_adc_init_clk_div(struct device *dev, struct ingenic_adc *adc) +{ + struct clk *parent_clk; + unsigned long parent_rate, rate; + unsigned int div_main, div_ms, div_10us; + + parent_clk = clk_get_parent(adc->clk); + if (!parent_clk) { + dev_err(dev, "ADC clock has no parent\n"); + return -ENODEV; + } + parent_rate = clk_get_rate(parent_clk); + + /* + * The JZ4770 ADC works at 20 kHz to 200 kHz. + * We pick the highest rate possible. + */ + div_main = DIV_ROUND_UP(parent_rate, 200000); + div_main = clamp(div_main, 1u, 256u); + rate = parent_rate / div_main; + if (rate < 20000 || rate > 200000) { + dev_err(dev, "No valid divider for ADC main clock\n"); + return -EINVAL; + } + + /* We also need a divider that produces a 10us clock. */ + div_10us = DIV_ROUND_UP(rate, 10000); + /* And another, which produces a 1ms clock. */ + div_ms = DIV_ROUND_UP(rate, 1000); + + writel(((div_ms - 1) << JZ4770_ADC_REG_ADCLK_CLKDIVMS_LSB) | + ((div_10us - 1) << JZ4770_ADC_REG_ADCLK_CLKDIV10US_LSB) | (div_main - 1) << JZ_ADC_REG_ADCLK_CLKDIV_LSB, adc->base + JZ_ADC_REG_ADCLK); @@ -201,6 +258,8 @@ static const struct ingenic_adc_soc_data jz4725b_adc_soc_data = { .battery_raw_avail_size = ARRAY_SIZE(jz4725b_adc_battery_raw_avail), .battery_scale_avail = jz4725b_adc_battery_scale_avail, .battery_scale_avail_size = ARRAY_SIZE(jz4725b_adc_battery_scale_avail), + .battery_vref_mode = true, + .has_aux2 = false, .init_clk_div = jz4725b_adc_init_clk_div, }; @@ -211,9 +270,23 @@ static const struct ingenic_adc_soc_data jz4740_adc_soc_data = { .battery_raw_avail_size = ARRAY_SIZE(jz4740_adc_battery_raw_avail), .battery_scale_avail = jz4740_adc_battery_scale_avail, .battery_scale_avail_size = ARRAY_SIZE(jz4740_adc_battery_scale_avail), + .battery_vref_mode = true, + .has_aux2 = false, .init_clk_div = NULL, /* no ADCLK register on JZ4740 */ }; +static const struct ingenic_adc_soc_data jz4770_adc_soc_data = { + .battery_high_vref = JZ4770_ADC_BATTERY_VREF, + .battery_high_vref_bits = JZ4770_ADC_BATTERY_VREF_BITS, + .battery_raw_avail = jz4770_adc_battery_raw_avail, + .battery_raw_avail_size = ARRAY_SIZE(jz4770_adc_battery_raw_avail), + .battery_scale_avail = jz4770_adc_battery_scale_avail, + .battery_scale_avail_size = ARRAY_SIZE(jz4770_adc_battery_scale_avail), + .battery_vref_mode = false, + .has_aux2 = true, + .init_clk_div = jz4770_adc_init_clk_div, +}; + static int ingenic_adc_read_avail(struct iio_dev *iio_dev, struct iio_chan_spec const *chan, const int **vals, @@ -239,6 +312,42 @@ static int ingenic_adc_read_avail(struct iio_dev *iio_dev, }; } +static int ingenic_adc_read_chan_info_raw(struct ingenic_adc *adc, + struct iio_chan_spec const *chan, + int *val) +{ + int bit, ret, engine = (chan->channel == INGENIC_ADC_BATTERY); + + /* We cannot sample AUX/AUX2 in parallel. */ + mutex_lock(&adc->aux_lock); + if (adc->soc_data->has_aux2 && engine == 0) { + bit = BIT(chan->channel == INGENIC_ADC_AUX2); + ingenic_adc_set_config(adc, JZ_ADC_REG_CFG_AUX_MD, bit); + } + + clk_enable(adc->clk); + ret = ingenic_adc_capture(adc, engine); + if (ret) + goto out; + + switch (chan->channel) { + case INGENIC_ADC_AUX: + case INGENIC_ADC_AUX2: + *val = readw(adc->base + JZ_ADC_REG_ADSDAT); + break; + case INGENIC_ADC_BATTERY: + *val = readw(adc->base + JZ_ADC_REG_ADBDAT); + break; + } + + ret = IIO_VAL_INT; +out: + clk_disable(adc->clk); + mutex_unlock(&adc->aux_lock); + + return ret; +} + static int ingenic_adc_read_raw(struct iio_dev *iio_dev, struct iio_chan_spec const *chan, int *val, @@ -246,32 +355,14 @@ static int ingenic_adc_read_raw(struct iio_dev *iio_dev, long m) { struct ingenic_adc *adc = iio_priv(iio_dev); - int ret; switch (m) { case IIO_CHAN_INFO_RAW: - clk_enable(adc->clk); - ret = ingenic_adc_capture(adc, chan->channel); - if (ret) { - clk_disable(adc->clk); - return ret; - } - - switch (chan->channel) { - case INGENIC_ADC_AUX: - *val = readw(adc->base + JZ_ADC_REG_ADSDAT); - break; - case INGENIC_ADC_BATTERY: - *val = readw(adc->base + JZ_ADC_REG_ADBDAT); - break; - } - - clk_disable(adc->clk); - - return IIO_VAL_INT; + return ingenic_adc_read_chan_info_raw(adc, chan, val); case IIO_CHAN_INFO_SCALE: switch (chan->channel) { case INGENIC_ADC_AUX: + case INGENIC_ADC_AUX2: *val = JZ_ADC_AUX_VREF; *val2 = JZ_ADC_AUX_VREF_BITS; break; @@ -322,6 +413,14 @@ static const struct iio_chan_spec ingenic_channels[] = { .indexed = 1, .channel = INGENIC_ADC_BATTERY, }, + { /* Must always be last in the array. */ + .extend_name = "aux2", + .type = IIO_VOLTAGE, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | + BIT(IIO_CHAN_INFO_SCALE), + .indexed = 1, + .channel = INGENIC_ADC_AUX2, + }, }; static int ingenic_adc_probe(struct platform_device *pdev) @@ -343,6 +442,7 @@ static int ingenic_adc_probe(struct platform_device *pdev) adc = iio_priv(iio_dev); mutex_init(&adc->lock); + mutex_init(&adc->aux_lock); adc->soc_data = soc_data; mem_base = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -374,6 +474,7 @@ static int ingenic_adc_probe(struct platform_device *pdev) /* Put hardware in a known passive state. */ writeb(0x00, adc->base + JZ_ADC_REG_ENABLE); writeb(0xff, adc->base + JZ_ADC_REG_CTRL); + usleep_range(2000, 3000); /* Must wait at least 2ms. */ clk_disable(adc->clk); ret = devm_add_action_or_reset(dev, ingenic_adc_clk_cleanup, adc->clk); @@ -387,6 +488,9 @@ static int ingenic_adc_probe(struct platform_device *pdev) iio_dev->modes = INDIO_DIRECT_MODE; iio_dev->channels = ingenic_channels; iio_dev->num_channels = ARRAY_SIZE(ingenic_channels); + /* Remove AUX2 from the list of supported channels. */ + if (!adc->soc_data->has_aux2) + iio_dev->num_channels -= 1; iio_dev->info = &ingenic_adc_info; ret = devm_iio_device_register(dev, iio_dev); @@ -400,6 +504,7 @@ static int ingenic_adc_probe(struct platform_device *pdev) static const struct of_device_id ingenic_adc_of_match[] = { { .compatible = "ingenic,jz4725b-adc", .data = &jz4725b_adc_soc_data, }, { .compatible = "ingenic,jz4740-adc", .data = &jz4740_adc_soc_data, }, + { .compatible = "ingenic,jz4770-adc", .data = &jz4770_adc_soc_data, }, { }, }; MODULE_DEVICE_TABLE(of, ingenic_adc_of_match); diff --git a/drivers/iio/adc/sc27xx_adc.c b/drivers/iio/adc/sc27xx_adc.c index a6c046575ec3..66b387f9b36d 100644 --- a/drivers/iio/adc/sc27xx_adc.c +++ b/drivers/iio/adc/sc27xx_adc.c @@ -477,13 +477,6 @@ static void sc27xx_adc_disable(void *_data) SC27XX_MODULE_ADC_EN, 0); } -static void sc27xx_adc_free_hwlock(void *_data) -{ - struct hwspinlock *hwlock = _data; - - hwspin_lock_free(hwlock); -} - static int sc27xx_adc_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; @@ -520,19 +513,12 @@ static int sc27xx_adc_probe(struct platform_device *pdev) return ret; } - sc27xx_data->hwlock = hwspin_lock_request_specific(ret); + sc27xx_data->hwlock = devm_hwspin_lock_request_specific(dev, ret); if (!sc27xx_data->hwlock) { dev_err(dev, "failed to request hwspinlock\n"); return -ENXIO; } - ret = devm_add_action_or_reset(dev, sc27xx_adc_free_hwlock, - sc27xx_data->hwlock); - if (ret) { - dev_err(dev, "failed to add hwspinlock action\n"); - return ret; - } - sc27xx_data->dev = dev; ret = sc27xx_adc_enable(sc27xx_data); diff --git a/drivers/iio/chemical/atlas-ph-sensor.c b/drivers/iio/chemical/atlas-ph-sensor.c index 3a20cb5d9bff..6c175eb1c7a7 100644 --- a/drivers/iio/chemical/atlas-ph-sensor.c +++ b/drivers/iio/chemical/atlas-ph-sensor.c @@ -323,16 +323,16 @@ static int atlas_buffer_predisable(struct iio_dev *indio_dev) struct atlas_data *data = iio_priv(indio_dev); int ret; - ret = iio_triggered_buffer_predisable(indio_dev); + ret = atlas_set_interrupt(data, false); if (ret) return ret; - ret = atlas_set_interrupt(data, false); + pm_runtime_mark_last_busy(&data->client->dev); + ret = pm_runtime_put_autosuspend(&data->client->dev); if (ret) return ret; - pm_runtime_mark_last_busy(&data->client->dev); - return pm_runtime_put_autosuspend(&data->client->dev); + return iio_triggered_buffer_predisable(indio_dev); } static const struct iio_trigger_ops atlas_interrupt_trigger_ops = { diff --git a/drivers/iio/gyro/adis16080.c b/drivers/iio/gyro/adis16080.c index 236220d6de02..1b84b8e112fe 100644 --- a/drivers/iio/gyro/adis16080.c +++ b/drivers/iio/gyro/adis16080.c @@ -38,10 +38,12 @@ struct adis16080_chip_info { * @us: actual spi_device to write data * @info: chip specific parameters * @buf: transmit or receive buffer + * @lock lock to protect buffer during reads **/ struct adis16080_state { struct spi_device *us; const struct adis16080_chip_info *info; + struct mutex lock; __be16 buf ____cacheline_aligned; }; @@ -82,9 +84,9 @@ static int adis16080_read_raw(struct iio_dev *indio_dev, switch (mask) { case IIO_CHAN_INFO_RAW: - mutex_lock(&indio_dev->mlock); + mutex_lock(&st->lock); ret = adis16080_read_sample(indio_dev, chan->address, val); - mutex_unlock(&indio_dev->mlock); + mutex_unlock(&st->lock); return ret ? ret : IIO_VAL_INT; case IIO_CHAN_INFO_SCALE: switch (chan->type) { @@ -196,6 +198,8 @@ static int adis16080_probe(struct spi_device *spi) /* this is only used for removal purposes */ spi_set_drvdata(spi, indio_dev); + mutex_init(&st->lock); + /* Allocate the comms buffers */ st->us = spi; st->info = &adis16080_chip_info[id->driver_data]; diff --git a/drivers/iio/gyro/adis16130.c b/drivers/iio/gyro/adis16130.c index de3f66f89496..79e63c8a2ea8 100644 --- a/drivers/iio/gyro/adis16130.c +++ b/drivers/iio/gyro/adis16130.c @@ -76,9 +76,7 @@ static int adis16130_read_raw(struct iio_dev *indio_dev, switch (mask) { case IIO_CHAN_INFO_RAW: /* Take the iio_dev status lock */ - mutex_lock(&indio_dev->mlock); ret = adis16130_spi_read(indio_dev, chan->address, &temp); - mutex_unlock(&indio_dev->mlock); if (ret) return ret; *val = temp; diff --git a/drivers/iio/gyro/itg3200_core.c b/drivers/iio/gyro/itg3200_core.c index 998fb8d66fe3..981ae2291505 100644 --- a/drivers/iio/gyro/itg3200_core.c +++ b/drivers/iio/gyro/itg3200_core.c @@ -154,7 +154,7 @@ static int itg3200_write_raw(struct iio_dev *indio_dev, t); mutex_unlock(&indio_dev->mlock); - return ret; + return ret; default: return -EINVAL; diff --git a/drivers/iio/imu/inv_mpu6050/Makefile b/drivers/iio/imu/inv_mpu6050/Makefile index 70ffe0d13d8c..c103441a906b 100644 --- a/drivers/iio/imu/inv_mpu6050/Makefile +++ b/drivers/iio/imu/inv_mpu6050/Makefile @@ -4,10 +4,11 @@ # obj-$(CONFIG_INV_MPU6050_IIO) += inv-mpu6050.o -inv-mpu6050-objs := inv_mpu_core.o inv_mpu_ring.o inv_mpu_trigger.o +inv-mpu6050-y := inv_mpu_core.o inv_mpu_ring.o inv_mpu_trigger.o \ + inv_mpu_aux.o inv_mpu_magn.o obj-$(CONFIG_INV_MPU6050_I2C) += inv-mpu6050-i2c.o -inv-mpu6050-i2c-objs := inv_mpu_i2c.o inv_mpu_acpi.o +inv-mpu6050-i2c-y := inv_mpu_i2c.o inv_mpu_acpi.o obj-$(CONFIG_INV_MPU6050_SPI) += inv-mpu6050-spi.o -inv-mpu6050-spi-objs := inv_mpu_spi.o +inv-mpu6050-spi-y := inv_mpu_spi.o diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.c new file mode 100644 index 000000000000..7327e5723f96 --- /dev/null +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.c @@ -0,0 +1,204 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2019 TDK-InvenSense, Inc. + */ + +#include <linux/kernel.h> +#include <linux/device.h> +#include <linux/regmap.h> +#include <linux/delay.h> + +#include "inv_mpu_aux.h" +#include "inv_mpu_iio.h" + +/* + * i2c master auxiliary bus transfer function. + * Requires the i2c operations to be correctly setup before. + */ +static int inv_mpu_i2c_master_xfer(const struct inv_mpu6050_state *st) +{ + /* use 50hz frequency for xfer */ + const unsigned int freq = 50; + const unsigned int period_ms = 1000 / freq; + uint8_t d; + unsigned int user_ctrl; + int ret; + + /* set sample rate */ + d = INV_MPU6050_FIFO_RATE_TO_DIVIDER(freq); + ret = regmap_write(st->map, st->reg->sample_rate_div, d); + if (ret) + return ret; + + /* start i2c master */ + user_ctrl = st->chip_config.user_ctrl | INV_MPU6050_BIT_I2C_MST_EN; + ret = regmap_write(st->map, st->reg->user_ctrl, user_ctrl); + if (ret) + goto error_restore_rate; + + /* wait for xfer: 1 period + half-period margin */ + msleep(period_ms + period_ms / 2); + + /* stop i2c master */ + user_ctrl = st->chip_config.user_ctrl; + ret = regmap_write(st->map, st->reg->user_ctrl, user_ctrl); + if (ret) + goto error_stop_i2c; + + /* restore sample rate */ + d = st->chip_config.divider; + ret = regmap_write(st->map, st->reg->sample_rate_div, d); + if (ret) + goto error_restore_rate; + + return 0; + +error_stop_i2c: + regmap_write(st->map, st->reg->user_ctrl, st->chip_config.user_ctrl); +error_restore_rate: + regmap_write(st->map, st->reg->sample_rate_div, st->chip_config.divider); + return ret; +} + +/** + * inv_mpu_aux_init() - init i2c auxiliary bus + * @st: driver internal state + * + * Returns 0 on success, a negative error code otherwise. + */ +int inv_mpu_aux_init(const struct inv_mpu6050_state *st) +{ + unsigned int val; + int ret; + + /* configure i2c master */ + val = INV_MPU6050_BITS_I2C_MST_CLK_400KHZ | + INV_MPU6050_BIT_WAIT_FOR_ES; + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_MST_CTRL, val); + if (ret) + return ret; + + /* configure i2c master delay */ + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV4_CTRL, 0); + if (ret) + return ret; + + val = INV_MPU6050_BIT_I2C_SLV0_DLY_EN | + INV_MPU6050_BIT_I2C_SLV1_DLY_EN | + INV_MPU6050_BIT_I2C_SLV2_DLY_EN | + INV_MPU6050_BIT_I2C_SLV3_DLY_EN | + INV_MPU6050_BIT_DELAY_ES_SHADOW; + return regmap_write(st->map, INV_MPU6050_REG_I2C_MST_DELAY_CTRL, val); +} + +/** + * inv_mpu_aux_read() - read register function for i2c auxiliary bus + * @st: driver internal state. + * @addr: chip i2c Address + * @reg: chip register address + * @val: buffer for storing read bytes + * @size: number of bytes to read + * + * Returns 0 on success, a negative error code otherwise. + */ +int inv_mpu_aux_read(const struct inv_mpu6050_state *st, uint8_t addr, + uint8_t reg, uint8_t *val, size_t size) +{ + unsigned int status; + int ret; + + if (size > 0x0F) + return -EINVAL; + + /* setup i2c SLV0 control: i2c addr, register, enable + size */ + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_ADDR(0), + INV_MPU6050_BIT_I2C_SLV_RNW | addr); + if (ret) + return ret; + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_REG(0), reg); + if (ret) + return ret; + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0), + INV_MPU6050_BIT_SLV_EN | size); + if (ret) + return ret; + + /* do i2c xfer */ + ret = inv_mpu_i2c_master_xfer(st); + if (ret) + goto error_disable_i2c; + + /* disable i2c slave */ + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0), 0); + if (ret) + goto error_disable_i2c; + + /* check i2c status */ + ret = regmap_read(st->map, INV_MPU6050_REG_I2C_MST_STATUS, &status); + if (ret) + return ret; + if (status & INV_MPU6050_BIT_I2C_SLV0_NACK) + return -EIO; + + /* read data in registers */ + return regmap_bulk_read(st->map, INV_MPU6050_REG_EXT_SENS_DATA, + val, size); + +error_disable_i2c: + regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0), 0); + return ret; +} + +/** + * inv_mpu_aux_write() - write register function for i2c auxiliary bus + * @st: driver internal state. + * @addr: chip i2c Address + * @reg: chip register address + * @val: 1 byte value to write + * + * Returns 0 on success, a negative error code otherwise. + */ +int inv_mpu_aux_write(const struct inv_mpu6050_state *st, uint8_t addr, + uint8_t reg, uint8_t val) +{ + unsigned int status; + int ret; + + /* setup i2c SLV0 control: i2c addr, register, value, enable + size */ + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_ADDR(0), addr); + if (ret) + return ret; + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_REG(0), reg); + if (ret) + return ret; + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_DO(0), val); + if (ret) + return ret; + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0), + INV_MPU6050_BIT_SLV_EN | 1); + if (ret) + return ret; + + /* do i2c xfer */ + ret = inv_mpu_i2c_master_xfer(st); + if (ret) + goto error_disable_i2c; + + /* disable i2c slave */ + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0), 0); + if (ret) + goto error_disable_i2c; + + /* check i2c status */ + ret = regmap_read(st->map, INV_MPU6050_REG_I2C_MST_STATUS, &status); + if (ret) + return ret; + if (status & INV_MPU6050_BIT_I2C_SLV0_NACK) + return -EIO; + + return 0; + +error_disable_i2c: + regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0), 0); + return ret; +} diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.h b/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.h new file mode 100644 index 000000000000..b66997545762 --- /dev/null +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.h @@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2019 TDK-InvenSense, Inc. + */ + +#ifndef INV_MPU_AUX_H_ +#define INV_MPU_AUX_H_ + +#include "inv_mpu_iio.h" + +int inv_mpu_aux_init(const struct inv_mpu6050_state *st); + +int inv_mpu_aux_read(const struct inv_mpu6050_state *st, uint8_t addr, + uint8_t reg, uint8_t *val, size_t size); + +int inv_mpu_aux_write(const struct inv_mpu6050_state *st, uint8_t addr, + uint8_t reg, uint8_t val); + +#endif /* INV_MPU_AUX_H_ */ diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c index b17f060b52fc..354030e9bed5 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c @@ -17,6 +17,7 @@ #include <linux/platform_device.h> #include <linux/regulator/consumer.h> #include "inv_mpu_iio.h" +#include "inv_mpu_magn.h" /* * this is the gyro scale translated from dynamic range plus/minus @@ -103,6 +104,7 @@ static const struct inv_mpu6050_chip_config chip_config_6050 = { .divider = INV_MPU6050_FIFO_RATE_TO_DIVIDER(INV_MPU6050_INIT_FIFO_RATE), .gyro_fifo_enable = false, .accl_fifo_enable = false, + .magn_fifo_enable = false, .accl_fs = INV_MPU6050_FS_02G, .user_ctrl = 0, }; @@ -332,6 +334,11 @@ static int inv_mpu6050_init_config(struct iio_dev *indio_dev) */ st->chip_period = NSEC_PER_MSEC; + /* magn chip init, noop if not present in the chip */ + result = inv_mpu_magn_probe(st); + if (result) + goto error_power_off; + return inv_mpu6050_set_power_itg(st, false); error_power_off: @@ -411,6 +418,9 @@ static int inv_mpu6050_read_channel_data(struct iio_dev *indio_dev, ret = inv_mpu6050_sensor_show(st, st->reg->temperature, IIO_MOD_X, val); break; + case IIO_MAGN: + ret = inv_mpu_magn_read(st, chan->channel2, val); + break; default: ret = -EINVAL; break; @@ -469,6 +479,8 @@ inv_mpu6050_read_raw(struct iio_dev *indio_dev, *val2 = INV_MPU6050_TEMP_SCALE; return IIO_VAL_INT_PLUS_MICRO; + case IIO_MAGN: + return inv_mpu_magn_get_scale(st, chan, val, val2); default: return -EINVAL; } @@ -710,6 +722,11 @@ inv_mpu6050_fifo_rate_store(struct device *dev, struct device_attribute *attr, if (result) goto fifo_rate_fail_power_off; + /* update rate for magn, noop if not present in chip */ + result = inv_mpu_magn_set_rate(st, fifo_rate); + if (result) + goto fifo_rate_fail_power_off; + fifo_rate_fail_power_off: result |= inv_mpu6050_set_power_itg(st, false); fifo_rate_fail_unlock: @@ -795,8 +812,14 @@ inv_get_mount_matrix(const struct iio_dev *indio_dev, const struct iio_chan_spec *chan) { struct inv_mpu6050_state *data = iio_priv(indio_dev); + const struct iio_mount_matrix *matrix; - return &data->orientation; + if (chan->type == IIO_MAGN) + matrix = &data->magn_orient; + else + matrix = &data->orientation; + + return matrix; } static const struct iio_chan_spec_ext_info inv_ext_info[] = { @@ -864,6 +887,98 @@ static const unsigned long inv_mpu_scan_masks[] = { 0, }; +#define INV_MPU9X50_MAGN_CHAN(_chan2, _bits, _index) \ + { \ + .type = IIO_MAGN, \ + .modified = 1, \ + .channel2 = _chan2, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_SCALE) | \ + BIT(IIO_CHAN_INFO_RAW), \ + .scan_index = _index, \ + .scan_type = { \ + .sign = 's', \ + .realbits = _bits, \ + .storagebits = 16, \ + .shift = 0, \ + .endianness = IIO_BE, \ + }, \ + .ext_info = inv_ext_info, \ + } + +static const struct iio_chan_spec inv_mpu9250_channels[] = { + IIO_CHAN_SOFT_TIMESTAMP(INV_MPU9X50_SCAN_TIMESTAMP), + /* + * Note that temperature should only be via polled reading only, + * not the final scan elements output. + */ + { + .type = IIO_TEMP, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) + | BIT(IIO_CHAN_INFO_OFFSET) + | BIT(IIO_CHAN_INFO_SCALE), + .scan_index = -1, + }, + INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_X, INV_MPU6050_SCAN_GYRO_X), + INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Y, INV_MPU6050_SCAN_GYRO_Y), + INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Z, INV_MPU6050_SCAN_GYRO_Z), + + INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_X, INV_MPU6050_SCAN_ACCL_X), + INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_Y, INV_MPU6050_SCAN_ACCL_Y), + INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_Z, INV_MPU6050_SCAN_ACCL_Z), + + /* Magnetometer resolution is 16 bits */ + INV_MPU9X50_MAGN_CHAN(IIO_MOD_X, 16, INV_MPU9X50_SCAN_MAGN_X), + INV_MPU9X50_MAGN_CHAN(IIO_MOD_Y, 16, INV_MPU9X50_SCAN_MAGN_Y), + INV_MPU9X50_MAGN_CHAN(IIO_MOD_Z, 16, INV_MPU9X50_SCAN_MAGN_Z), +}; + +static const unsigned long inv_mpu9x50_scan_masks[] = { + /* 3-axis accel */ + BIT(INV_MPU6050_SCAN_ACCL_X) + | BIT(INV_MPU6050_SCAN_ACCL_Y) + | BIT(INV_MPU6050_SCAN_ACCL_Z), + /* 3-axis gyro */ + BIT(INV_MPU6050_SCAN_GYRO_X) + | BIT(INV_MPU6050_SCAN_GYRO_Y) + | BIT(INV_MPU6050_SCAN_GYRO_Z), + /* 3-axis magn */ + BIT(INV_MPU9X50_SCAN_MAGN_X) + | BIT(INV_MPU9X50_SCAN_MAGN_Y) + | BIT(INV_MPU9X50_SCAN_MAGN_Z), + /* 6-axis accel + gyro */ + BIT(INV_MPU6050_SCAN_ACCL_X) + | BIT(INV_MPU6050_SCAN_ACCL_Y) + | BIT(INV_MPU6050_SCAN_ACCL_Z) + | BIT(INV_MPU6050_SCAN_GYRO_X) + | BIT(INV_MPU6050_SCAN_GYRO_Y) + | BIT(INV_MPU6050_SCAN_GYRO_Z), + /* 6-axis accel + magn */ + BIT(INV_MPU6050_SCAN_ACCL_X) + | BIT(INV_MPU6050_SCAN_ACCL_Y) + | BIT(INV_MPU6050_SCAN_ACCL_Z) + | BIT(INV_MPU9X50_SCAN_MAGN_X) + | BIT(INV_MPU9X50_SCAN_MAGN_Y) + | BIT(INV_MPU9X50_SCAN_MAGN_Z), + /* 6-axis gyro + magn */ + BIT(INV_MPU6050_SCAN_GYRO_X) + | BIT(INV_MPU6050_SCAN_GYRO_Y) + | BIT(INV_MPU6050_SCAN_GYRO_Z) + | BIT(INV_MPU9X50_SCAN_MAGN_X) + | BIT(INV_MPU9X50_SCAN_MAGN_Y) + | BIT(INV_MPU9X50_SCAN_MAGN_Z), + /* 9-axis accel + gyro + magn */ + BIT(INV_MPU6050_SCAN_ACCL_X) + | BIT(INV_MPU6050_SCAN_ACCL_Y) + | BIT(INV_MPU6050_SCAN_ACCL_Z) + | BIT(INV_MPU6050_SCAN_GYRO_X) + | BIT(INV_MPU6050_SCAN_GYRO_Y) + | BIT(INV_MPU6050_SCAN_GYRO_Z) + | BIT(INV_MPU9X50_SCAN_MAGN_X) + | BIT(INV_MPU9X50_SCAN_MAGN_Y) + | BIT(INV_MPU9X50_SCAN_MAGN_Z), + 0, +}; + static const struct iio_chan_spec inv_icm20602_channels[] = { IIO_CHAN_SOFT_TIMESTAMP(INV_ICM20602_SCAN_TIMESTAMP), { @@ -1145,6 +1260,11 @@ int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name, return result; } + /* fill magnetometer orientation */ + result = inv_mpu_magn_set_orient(st); + if (result) + return result; + /* power is turned on inside check chip type*/ result = inv_check_and_setup_chip(st); if (result) @@ -1156,9 +1276,6 @@ int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name, return result; } - if (inv_mpu_bus_setup) - inv_mpu_bus_setup(indio_dev); - dev_set_drvdata(dev, indio_dev); indio_dev->dev.parent = dev; /* name will be NULL when enumerated via ACPI */ @@ -1167,14 +1284,37 @@ int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name, else indio_dev->name = dev_name(dev); - if (chip_type == INV_ICM20602) { + /* requires parent device set in indio_dev */ + if (inv_mpu_bus_setup) + inv_mpu_bus_setup(indio_dev); + + switch (chip_type) { + case INV_MPU9250: + case INV_MPU9255: + /* + * Use magnetometer inside the chip only if there is no i2c + * auxiliary device in use. + */ + if (!st->magn_disabled) { + indio_dev->channels = inv_mpu9250_channels; + indio_dev->num_channels = ARRAY_SIZE(inv_mpu9250_channels); + indio_dev->available_scan_masks = inv_mpu9x50_scan_masks; + } else { + indio_dev->channels = inv_mpu_channels; + indio_dev->num_channels = ARRAY_SIZE(inv_mpu_channels); + indio_dev->available_scan_masks = inv_mpu_scan_masks; + } + break; + case INV_ICM20602: indio_dev->channels = inv_icm20602_channels; indio_dev->num_channels = ARRAY_SIZE(inv_icm20602_channels); indio_dev->available_scan_masks = inv_icm20602_scan_masks; - } else { + break; + default: indio_dev->channels = inv_mpu_channels; indio_dev->num_channels = ARRAY_SIZE(inv_mpu_channels); indio_dev->available_scan_masks = inv_mpu_scan_masks; + break; } indio_dev->info = &mpu_info; diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c index 4b8b5a87398c..389cc8505e0e 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c @@ -68,6 +68,56 @@ static const char *inv_mpu_match_acpi_device(struct device *dev, return dev_name(dev); } +static bool inv_mpu_i2c_aux_bus(struct device *dev) +{ + struct inv_mpu6050_state *st = iio_priv(dev_get_drvdata(dev)); + + switch (st->chip_type) { + case INV_ICM20608: + case INV_ICM20602: + /* no i2c auxiliary bus on the chip */ + return false; + case INV_MPU9250: + case INV_MPU9255: + if (st->magn_disabled) + return true; + else + return false; + default: + return true; + } +} + +/* + * MPU9xxx magnetometer support requires to disable i2c auxiliary bus support. + * To ensure backward compatibility with existing setups, do not disable + * i2c auxiliary bus if it used. + * Check for i2c-gate node in devicetree and set magnetometer disabled. + * Only MPU6500 is supported by ACPI, no need to check. + */ +static int inv_mpu_magn_disable(struct iio_dev *indio_dev) +{ + struct inv_mpu6050_state *st = iio_priv(indio_dev); + struct device *dev = indio_dev->dev.parent; + struct device_node *mux_node; + + switch (st->chip_type) { + case INV_MPU9250: + case INV_MPU9255: + mux_node = of_get_child_by_name(dev->of_node, "i2c-gate"); + if (mux_node != NULL) { + st->magn_disabled = true; + dev_warn(dev, "disable internal use of magnetometer\n"); + } + of_node_put(mux_node); + break; + default: + break; + } + + return 0; +} + /** * inv_mpu_probe() - probe function. * @client: i2c client. @@ -112,17 +162,12 @@ static int inv_mpu_probe(struct i2c_client *client, } result = inv_mpu_core_probe(regmap, client->irq, name, - NULL, chip_type); + inv_mpu_magn_disable, chip_type); if (result < 0) return result; st = iio_priv(dev_get_drvdata(&client->dev)); - switch (st->chip_type) { - case INV_ICM20608: - case INV_ICM20602: - /* no i2c auxiliary bus on the chip */ - break; - default: + if (inv_mpu_i2c_aux_bus(&client->dev)) { /* declare i2c auxiliary bus */ st->muxc = i2c_mux_alloc(client->adapter, &client->dev, 1, 0, I2C_MUX_LOCKED | I2C_MUX_GATE, @@ -137,7 +182,6 @@ static int inv_mpu_probe(struct i2c_client *client, result = inv_mpu_acpi_create_mux_client(client); if (result) goto out_del_mux; - break; } return 0; diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h index db1c6904388b..52fcf45050a5 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h @@ -2,6 +2,10 @@ /* * Copyright (C) 2012 Invensense, Inc. */ + +#ifndef INV_MPU_IIO_H_ +#define INV_MPU_IIO_H_ + #include <linux/i2c.h> #include <linux/i2c-mux.h> #include <linux/mutex.h> @@ -82,6 +86,7 @@ enum inv_devices { * @accl_fs: accel full scale range. * @accl_fifo_enable: enable accel data output * @gyro_fifo_enable: enable gyro data output + * @magn_fifo_enable: enable magn data output * @divider: chip sample rate divider (sample rate divider - 1) */ struct inv_mpu6050_chip_config { @@ -90,6 +95,7 @@ struct inv_mpu6050_chip_config { unsigned int accl_fs:2; unsigned int accl_fifo_enable:1; unsigned int gyro_fifo_enable:1; + unsigned int magn_fifo_enable:1; u8 divider; u8 user_ctrl; }; @@ -125,6 +131,9 @@ struct inv_mpu6050_hw { * @it_timestamp: timestamp from previous interrupt. * @data_timestamp: timestamp for next data sample. * @vddio_supply voltage regulator for the chip. + * @magn_disabled: magnetometer disabled for backward compatibility reason. + * @magn_raw_to_gauss: coefficient to convert mag raw value to Gauss. + * @magn_orient: magnetometer sensor chip orientation if available. */ struct inv_mpu6050_state { struct mutex lock; @@ -146,6 +155,9 @@ struct inv_mpu6050_state { s64 it_timestamp; s64 data_timestamp; struct regulator *vddio_supply; + bool magn_disabled; + s32 magn_raw_to_gauss[3]; + struct iio_mount_matrix magn_orient; }; /*register and associated bit definition*/ @@ -158,9 +170,41 @@ struct inv_mpu6050_state { #define INV_MPU6050_REG_ACCEL_CONFIG 0x1C #define INV_MPU6050_REG_FIFO_EN 0x23 +#define INV_MPU6050_BIT_SLAVE_0 0x01 +#define INV_MPU6050_BIT_SLAVE_1 0x02 +#define INV_MPU6050_BIT_SLAVE_2 0x04 #define INV_MPU6050_BIT_ACCEL_OUT 0x08 #define INV_MPU6050_BITS_GYRO_OUT 0x70 +#define INV_MPU6050_REG_I2C_MST_CTRL 0x24 +#define INV_MPU6050_BITS_I2C_MST_CLK_400KHZ 0x0D +#define INV_MPU6050_BIT_I2C_MST_P_NSR 0x10 +#define INV_MPU6050_BIT_SLV3_FIFO_EN 0x20 +#define INV_MPU6050_BIT_WAIT_FOR_ES 0x40 +#define INV_MPU6050_BIT_MULT_MST_EN 0x80 + +/* control I2C slaves from 0 to 3 */ +#define INV_MPU6050_REG_I2C_SLV_ADDR(_x) (0x25 + 3 * (_x)) +#define INV_MPU6050_BIT_I2C_SLV_RNW 0x80 + +#define INV_MPU6050_REG_I2C_SLV_REG(_x) (0x26 + 3 * (_x)) + +#define INV_MPU6050_REG_I2C_SLV_CTRL(_x) (0x27 + 3 * (_x)) +#define INV_MPU6050_BIT_SLV_GRP 0x10 +#define INV_MPU6050_BIT_SLV_REG_DIS 0x20 +#define INV_MPU6050_BIT_SLV_BYTE_SW 0x40 +#define INV_MPU6050_BIT_SLV_EN 0x80 + +/* I2C master delay register */ +#define INV_MPU6050_REG_I2C_SLV4_CTRL 0x34 +#define INV_MPU6050_BITS_I2C_MST_DLY(_x) ((_x) & 0x1F) + +#define INV_MPU6050_REG_I2C_MST_STATUS 0x36 +#define INV_MPU6050_BIT_I2C_SLV0_NACK 0x01 +#define INV_MPU6050_BIT_I2C_SLV1_NACK 0x02 +#define INV_MPU6050_BIT_I2C_SLV2_NACK 0x04 +#define INV_MPU6050_BIT_I2C_SLV3_NACK 0x08 + #define INV_MPU6050_REG_INT_ENABLE 0x38 #define INV_MPU6050_BIT_DATA_RDY_EN 0x01 #define INV_MPU6050_BIT_DMP_INT_EN 0x02 @@ -173,6 +217,18 @@ struct inv_mpu6050_state { #define INV_MPU6050_BIT_FIFO_OVERFLOW_INT 0x10 #define INV_MPU6050_BIT_RAW_DATA_RDY_INT 0x01 +#define INV_MPU6050_REG_EXT_SENS_DATA 0x49 + +/* I2C slaves data output from 0 to 3 */ +#define INV_MPU6050_REG_I2C_SLV_DO(_x) (0x63 + (_x)) + +#define INV_MPU6050_REG_I2C_MST_DELAY_CTRL 0x67 +#define INV_MPU6050_BIT_I2C_SLV0_DLY_EN 0x01 +#define INV_MPU6050_BIT_I2C_SLV1_DLY_EN 0x02 +#define INV_MPU6050_BIT_I2C_SLV2_DLY_EN 0x04 +#define INV_MPU6050_BIT_I2C_SLV3_DLY_EN 0x08 +#define INV_MPU6050_BIT_DELAY_ES_SHADOW 0x80 + #define INV_MPU6050_REG_USER_CTRL 0x6A #define INV_MPU6050_BIT_FIFO_RST 0x04 #define INV_MPU6050_BIT_DMP_RST 0x08 @@ -200,6 +256,9 @@ struct inv_mpu6050_state { #define INV_MPU6050_BYTES_PER_3AXIS_SENSOR 6 #define INV_MPU6050_FIFO_COUNT_BYTE 2 +/* MPU9X50 9-axis magnetometer */ +#define INV_MPU9X50_BYTES_MAGN 7 + /* ICM20602 FIFO samples include temperature readings */ #define INV_ICM20602_BYTES_PER_TEMP_SENSOR 2 @@ -227,8 +286,8 @@ struct inv_mpu6050_state { #define INV_ICM20602_TEMP_OFFSET 8170 #define INV_ICM20602_TEMP_SCALE 3060 -/* 6 + 6 round up and plus 8 */ -#define INV_MPU6050_OUTPUT_DATA_SIZE 24 +/* 6 + 6 + 7 (for MPU9x50) = 19 round up to 24 and plus 8 */ +#define INV_MPU6050_OUTPUT_DATA_SIZE 32 #define INV_MPU6050_REG_INT_PIN_CFG 0x37 #define INV_MPU6050_ACTIVE_HIGH 0x00 @@ -277,6 +336,11 @@ enum inv_mpu6050_scan { INV_MPU6050_SCAN_GYRO_Y, INV_MPU6050_SCAN_GYRO_Z, INV_MPU6050_SCAN_TIMESTAMP, + + INV_MPU9X50_SCAN_MAGN_X = INV_MPU6050_SCAN_GYRO_Z + 1, + INV_MPU9X50_SCAN_MAGN_Y, + INV_MPU9X50_SCAN_MAGN_Z, + INV_MPU9X50_SCAN_TIMESTAMP, }; /* scan element definition for ICM20602, which includes temperature */ @@ -342,3 +406,5 @@ void inv_mpu_acpi_delete_mux_client(struct i2c_client *client); int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name, int (*inv_mpu_bus_setup)(struct iio_dev *), int chip_type); extern const struct dev_pm_ops inv_mpu_pmops; + +#endif diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.c new file mode 100644 index 000000000000..02735af152c8 --- /dev/null +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.c @@ -0,0 +1,356 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2019 TDK-InvenSense, Inc. + */ + +#include <linux/kernel.h> +#include <linux/device.h> +#include <linux/string.h> + +#include "inv_mpu_aux.h" +#include "inv_mpu_iio.h" +#include "inv_mpu_magn.h" + +/* + * MPU9250 magnetometer is an AKM AK8963 chip on I2C aux bus + */ +#define INV_MPU_MAGN_I2C_ADDR 0x0C + +#define INV_MPU_MAGN_REG_WIA 0x00 +#define INV_MPU_MAGN_BITS_WIA 0x48 + +#define INV_MPU_MAGN_REG_ST1 0x02 +#define INV_MPU_MAGN_BIT_DRDY 0x01 +#define INV_MPU_MAGN_BIT_DOR 0x02 + +#define INV_MPU_MAGN_REG_DATA 0x03 + +#define INV_MPU_MAGN_REG_ST2 0x09 +#define INV_MPU_MAGN_BIT_HOFL 0x08 +#define INV_MPU_MAGN_BIT_BITM 0x10 + +#define INV_MPU_MAGN_REG_CNTL1 0x0A +#define INV_MPU_MAGN_BITS_MODE_PWDN 0x00 +#define INV_MPU_MAGN_BITS_MODE_SINGLE 0x01 +#define INV_MPU_MAGN_BITS_MODE_FUSE 0x0F +#define INV_MPU_MAGN_BIT_OUTPUT_BIT 0x10 + +#define INV_MPU_MAGN_REG_CNTL2 0x0B +#define INV_MPU_MAGN_BIT_SRST 0x01 + +#define INV_MPU_MAGN_REG_ASAX 0x10 +#define INV_MPU_MAGN_REG_ASAY 0x11 +#define INV_MPU_MAGN_REG_ASAZ 0x12 + +/* Magnetometer maximum frequency */ +#define INV_MPU_MAGN_FREQ_HZ_MAX 50 + +static bool inv_magn_supported(const struct inv_mpu6050_state *st) +{ + switch (st->chip_type) { + case INV_MPU9250: + case INV_MPU9255: + return true; + default: + return false; + } +} + +/* init magnetometer chip */ +static int inv_magn_init(struct inv_mpu6050_state *st) +{ + uint8_t val; + uint8_t asa[3]; + int ret; + + /* check whoami */ + ret = inv_mpu_aux_read(st, INV_MPU_MAGN_I2C_ADDR, INV_MPU_MAGN_REG_WIA, + &val, sizeof(val)); + if (ret) + return ret; + if (val != INV_MPU_MAGN_BITS_WIA) + return -ENODEV; + + /* reset chip */ + ret = inv_mpu_aux_write(st, INV_MPU_MAGN_I2C_ADDR, + INV_MPU_MAGN_REG_CNTL2, + INV_MPU_MAGN_BIT_SRST); + if (ret) + return ret; + + /* read fuse ROM data */ + ret = inv_mpu_aux_write(st, INV_MPU_MAGN_I2C_ADDR, + INV_MPU_MAGN_REG_CNTL1, + INV_MPU_MAGN_BITS_MODE_FUSE); + if (ret) + return ret; + + ret = inv_mpu_aux_read(st, INV_MPU_MAGN_I2C_ADDR, INV_MPU_MAGN_REG_ASAX, + asa, sizeof(asa)); + if (ret) + return ret; + + /* switch back to power-down */ + ret = inv_mpu_aux_write(st, INV_MPU_MAGN_I2C_ADDR, + INV_MPU_MAGN_REG_CNTL1, + INV_MPU_MAGN_BITS_MODE_PWDN); + if (ret) + return ret; + + /* + * Sensitivity adjustement and scale to Gauss + * + * Hadj = H * (((ASA - 128) * 0.5 / 128) + 1) + * Factor simplification: + * Hadj = H * ((ASA + 128) / 256) + * + * Sensor sentivity + * 0.15 uT in 16 bits mode + * 1 uT = 0.01 G and value is in micron (1e6) + * sensitvity = 0.15 uT * 0.01 * 1e6 + * + * raw_to_gauss = Hadj * 1500 + */ + st->magn_raw_to_gauss[0] = (((int32_t)asa[0] + 128) * 1500) / 256; + st->magn_raw_to_gauss[1] = (((int32_t)asa[1] + 128) * 1500) / 256; + st->magn_raw_to_gauss[2] = (((int32_t)asa[2] + 128) * 1500) / 256; + + return 0; +} + +/** + * inv_mpu_magn_probe() - probe and setup magnetometer chip + * @st: driver internal state + * + * Returns 0 on success, a negative error code otherwise + * + * It is probing the chip and setting up all needed i2c transfers. + * Noop if there is no magnetometer in the chip. + */ +int inv_mpu_magn_probe(struct inv_mpu6050_state *st) +{ + int ret; + + /* quit if chip is not supported */ + if (!inv_magn_supported(st)) + return 0; + + /* configure i2c master aux port */ + ret = inv_mpu_aux_init(st); + if (ret) + return ret; + + /* check and init mag chip */ + ret = inv_magn_init(st); + if (ret) + return ret; + + /* + * configure mpu i2c master accesses + * i2c SLV0: read sensor data, 7 bytes data(6)-ST2 + * Byte swap data to store them in big-endian in impair address groups + */ + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_ADDR(0), + INV_MPU6050_BIT_I2C_SLV_RNW | INV_MPU_MAGN_I2C_ADDR); + if (ret) + return ret; + + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_REG(0), + INV_MPU_MAGN_REG_DATA); + if (ret) + return ret; + + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0), + INV_MPU6050_BIT_SLV_EN | + INV_MPU6050_BIT_SLV_BYTE_SW | + INV_MPU6050_BIT_SLV_GRP | + INV_MPU9X50_BYTES_MAGN); + if (ret) + return ret; + + /* i2c SLV1: launch single measurement */ + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_ADDR(1), + INV_MPU_MAGN_I2C_ADDR); + if (ret) + return ret; + + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_REG(1), + INV_MPU_MAGN_REG_CNTL1); + if (ret) + return ret; + + /* add 16 bits mode */ + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_DO(1), + INV_MPU_MAGN_BITS_MODE_SINGLE | + INV_MPU_MAGN_BIT_OUTPUT_BIT); + if (ret) + return ret; + + return regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(1), + INV_MPU6050_BIT_SLV_EN | 1); +} + +/** + * inv_mpu_magn_set_rate() - set magnetometer sampling rate + * @st: driver internal state + * @fifo_rate: mpu set fifo rate + * + * Returns 0 on success, a negative error code otherwise + * + * Limit sampling frequency to the maximum value supported by the + * magnetometer chip. Resulting in duplicated data for higher frequencies. + * Noop if there is no magnetometer in the chip. + */ +int inv_mpu_magn_set_rate(const struct inv_mpu6050_state *st, int fifo_rate) +{ + uint8_t d; + + /* quit if chip is not supported */ + if (!inv_magn_supported(st)) + return 0; + + /* + * update i2c master delay to limit mag sampling to max frequency + * compute fifo_rate divider d: rate = fifo_rate / (d + 1) + */ + if (fifo_rate > INV_MPU_MAGN_FREQ_HZ_MAX) + d = fifo_rate / INV_MPU_MAGN_FREQ_HZ_MAX - 1; + else + d = 0; + + return regmap_write(st->map, INV_MPU6050_REG_I2C_SLV4_CTRL, d); +} + +/** + * inv_mpu_magn_set_orient() - fill magnetometer mounting matrix + * @st: driver internal state + * + * Returns 0 on success, a negative error code otherwise + * + * Fill magnetometer mounting matrix using the provided chip matrix. + */ +int inv_mpu_magn_set_orient(struct inv_mpu6050_state *st) +{ + const char *orient; + char *str; + int i; + + /* fill magnetometer orientation */ + switch (st->chip_type) { + case INV_MPU9250: + case INV_MPU9255: + /* x <- y */ + st->magn_orient.rotation[0] = st->orientation.rotation[3]; + st->magn_orient.rotation[1] = st->orientation.rotation[4]; + st->magn_orient.rotation[2] = st->orientation.rotation[5]; + /* y <- x */ + st->magn_orient.rotation[3] = st->orientation.rotation[0]; + st->magn_orient.rotation[4] = st->orientation.rotation[1]; + st->magn_orient.rotation[5] = st->orientation.rotation[2]; + /* z <- -z */ + for (i = 0; i < 3; ++i) { + orient = st->orientation.rotation[6 + i]; + /* use length + 2 for adding minus sign if needed */ + str = devm_kzalloc(regmap_get_device(st->map), + strlen(orient) + 2, GFP_KERNEL); + if (str == NULL) + return -ENOMEM; + if (strcmp(orient, "0") == 0) { + strcpy(str, orient); + } else if (orient[0] == '-') { + strcpy(str, &orient[1]); + } else { + str[0] = '-'; + strcpy(&str[1], orient); + } + st->magn_orient.rotation[6 + i] = str; + } + break; + default: + st->magn_orient = st->orientation; + break; + } + + return 0; +} + +/** + * inv_mpu_magn_read() - read magnetometer data + * @st: driver internal state + * @axis: IIO modifier axis value + * @val: store corresponding axis value + * + * Returns 0 on success, a negative error code otherwise + */ +int inv_mpu_magn_read(const struct inv_mpu6050_state *st, int axis, int *val) +{ + unsigned int user_ctrl, status; + __be16 data[3]; + uint8_t addr; + uint8_t d; + unsigned int period_ms; + int ret; + + /* quit if chip is not supported */ + if (!inv_magn_supported(st)) + return -ENODEV; + + /* Mag data: X - Y - Z */ + switch (axis) { + case IIO_MOD_X: + addr = 0; + break; + case IIO_MOD_Y: + addr = 1; + break; + case IIO_MOD_Z: + addr = 2; + break; + default: + return -EINVAL; + } + + /* set sample rate to max mag freq */ + d = INV_MPU6050_FIFO_RATE_TO_DIVIDER(INV_MPU_MAGN_FREQ_HZ_MAX); + ret = regmap_write(st->map, st->reg->sample_rate_div, d); + if (ret) + return ret; + + /* start i2c master, wait for xfer, stop */ + user_ctrl = st->chip_config.user_ctrl | INV_MPU6050_BIT_I2C_MST_EN; + ret = regmap_write(st->map, st->reg->user_ctrl, user_ctrl); + if (ret) + return ret; + + /* need to wait 2 periods + half-period margin */ + period_ms = 1000 / INV_MPU_MAGN_FREQ_HZ_MAX; + msleep(period_ms * 2 + period_ms / 2); + user_ctrl = st->chip_config.user_ctrl; + ret = regmap_write(st->map, st->reg->user_ctrl, user_ctrl); + if (ret) + return ret; + + /* restore sample rate */ + d = st->chip_config.divider; + ret = regmap_write(st->map, st->reg->sample_rate_div, d); + if (ret) + return ret; + + /* check i2c status and read raw data */ + ret = regmap_read(st->map, INV_MPU6050_REG_I2C_MST_STATUS, &status); + if (ret) + return ret; + + if (status & INV_MPU6050_BIT_I2C_SLV0_NACK || + status & INV_MPU6050_BIT_I2C_SLV1_NACK) + return -EIO; + + ret = regmap_bulk_read(st->map, INV_MPU6050_REG_EXT_SENS_DATA, + data, sizeof(data)); + if (ret) + return ret; + + *val = (int16_t)be16_to_cpu(data[addr]); + + return IIO_VAL_INT; +} diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.h b/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.h new file mode 100644 index 000000000000..b41bd0578478 --- /dev/null +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.h @@ -0,0 +1,36 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2019 TDK-InvenSense, Inc. + */ + +#ifndef INV_MPU_MAGN_H_ +#define INV_MPU_MAGN_H_ + +#include <linux/kernel.h> + +#include "inv_mpu_iio.h" + +int inv_mpu_magn_probe(struct inv_mpu6050_state *st); + +/** + * inv_mpu_magn_get_scale() - get magnetometer scale value + * @st: driver internal state + * + * Returns IIO data format. + */ +static inline int inv_mpu_magn_get_scale(const struct inv_mpu6050_state *st, + const struct iio_chan_spec *chan, + int *val, int *val2) +{ + *val = 0; + *val2 = st->magn_raw_to_gauss[chan->address]; + return IIO_VAL_INT_PLUS_MICRO; +} + +int inv_mpu_magn_set_rate(const struct inv_mpu6050_state *st, int fifo_rate); + +int inv_mpu_magn_set_orient(struct inv_mpu6050_state *st); + +int inv_mpu_magn_read(const struct inv_mpu6050_state *st, int axis, int *val); + +#endif /* INV_MPU_MAGN_H_ */ diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c index 5f9a5de0bab4..bbf68b474556 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c @@ -124,7 +124,8 @@ int inv_reset_fifo(struct iio_dev *indio_dev) /* enable interrupt */ if (st->chip_config.accl_fifo_enable || - st->chip_config.gyro_fifo_enable) { + st->chip_config.gyro_fifo_enable || + st->chip_config.magn_fifo_enable) { result = regmap_write(st->map, st->reg->int_enable, INV_MPU6050_BIT_DATA_RDY_EN); if (result) @@ -141,6 +142,8 @@ int inv_reset_fifo(struct iio_dev *indio_dev) d |= INV_MPU6050_BITS_GYRO_OUT; if (st->chip_config.accl_fifo_enable) d |= INV_MPU6050_BIT_ACCEL_OUT; + if (st->chip_config.magn_fifo_enable) + d |= INV_MPU6050_BIT_SLAVE_0; result = regmap_write(st->map, st->reg->fifo_en, d); if (result) goto reset_fifo_fail; @@ -190,7 +193,8 @@ irqreturn_t inv_mpu6050_read_fifo(int irq, void *p) } if (!(st->chip_config.accl_fifo_enable | - st->chip_config.gyro_fifo_enable)) + st->chip_config.gyro_fifo_enable | + st->chip_config.magn_fifo_enable)) goto end_session; bytes_per_datum = 0; if (st->chip_config.accl_fifo_enable) @@ -202,6 +206,9 @@ irqreturn_t inv_mpu6050_read_fifo(int irq, void *p) if (st->chip_type == INV_ICM20602) bytes_per_datum += INV_ICM20602_BYTES_PER_TEMP_SENSOR; + if (st->chip_config.magn_fifo_enable) + bytes_per_datum += INV_MPU9X50_BYTES_MAGN; + /* * read fifo_count register to know how many bytes are inside the FIFO * right now diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c index dd55e70b6f77..d7d951927a44 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c @@ -5,7 +5,7 @@ #include "inv_mpu_iio.h" -static void inv_scan_query(struct iio_dev *indio_dev) +static void inv_scan_query_mpu6050(struct iio_dev *indio_dev) { struct inv_mpu6050_state *st = iio_priv(indio_dev); @@ -26,6 +26,60 @@ static void inv_scan_query(struct iio_dev *indio_dev) indio_dev->active_scan_mask); } +static void inv_scan_query_mpu9x50(struct iio_dev *indio_dev) +{ + struct inv_mpu6050_state *st = iio_priv(indio_dev); + + inv_scan_query_mpu6050(indio_dev); + + /* no magnetometer if i2c auxiliary bus is used */ + if (st->magn_disabled) + return; + + st->chip_config.magn_fifo_enable = + test_bit(INV_MPU9X50_SCAN_MAGN_X, + indio_dev->active_scan_mask) || + test_bit(INV_MPU9X50_SCAN_MAGN_Y, + indio_dev->active_scan_mask) || + test_bit(INV_MPU9X50_SCAN_MAGN_Z, + indio_dev->active_scan_mask); +} + +static void inv_scan_query(struct iio_dev *indio_dev) +{ + struct inv_mpu6050_state *st = iio_priv(indio_dev); + + switch (st->chip_type) { + case INV_MPU9250: + case INV_MPU9255: + return inv_scan_query_mpu9x50(indio_dev); + default: + return inv_scan_query_mpu6050(indio_dev); + } +} + +static unsigned int inv_compute_skip_samples(const struct inv_mpu6050_state *st) +{ + unsigned int gyro_skip = 0; + unsigned int magn_skip = 0; + unsigned int skip_samples; + + /* gyro first sample is out of specs, skip it */ + if (st->chip_config.gyro_fifo_enable) + gyro_skip = 1; + + /* mag first sample is always not ready, skip it */ + if (st->chip_config.magn_fifo_enable) + magn_skip = 1; + + /* compute first samples to skip */ + skip_samples = gyro_skip; + if (magn_skip > skip_samples) + skip_samples = magn_skip; + + return skip_samples; +} + /** * inv_mpu6050_set_enable() - enable chip functions. * @indio_dev: Device driver instance. @@ -34,6 +88,7 @@ static void inv_scan_query(struct iio_dev *indio_dev) static int inv_mpu6050_set_enable(struct iio_dev *indio_dev, bool enable) { struct inv_mpu6050_state *st = iio_priv(indio_dev); + uint8_t d; int result; if (enable) { @@ -41,14 +96,11 @@ static int inv_mpu6050_set_enable(struct iio_dev *indio_dev, bool enable) if (result) return result; inv_scan_query(indio_dev); - st->skip_samples = 0; if (st->chip_config.gyro_fifo_enable) { result = inv_mpu6050_switch_engine(st, true, INV_MPU6050_BIT_PWR_GYRO_STBY); if (result) goto error_power_off; - /* gyro first sample is out of specs, skip it */ - st->skip_samples = 1; } if (st->chip_config.accl_fifo_enable) { result = inv_mpu6050_switch_engine(st, true, @@ -56,22 +108,32 @@ static int inv_mpu6050_set_enable(struct iio_dev *indio_dev, bool enable) if (result) goto error_gyro_off; } + if (st->chip_config.magn_fifo_enable) { + d = st->chip_config.user_ctrl | + INV_MPU6050_BIT_I2C_MST_EN; + result = regmap_write(st->map, st->reg->user_ctrl, d); + if (result) + goto error_accl_off; + st->chip_config.user_ctrl = d; + } + st->skip_samples = inv_compute_skip_samples(st); result = inv_reset_fifo(indio_dev); if (result) - goto error_accl_off; + goto error_magn_off; } else { result = regmap_write(st->map, st->reg->fifo_en, 0); if (result) - goto error_accl_off; + goto error_magn_off; result = regmap_write(st->map, st->reg->int_enable, 0); if (result) - goto error_accl_off; + goto error_magn_off; - result = regmap_write(st->map, st->reg->user_ctrl, - st->chip_config.user_ctrl); + d = st->chip_config.user_ctrl & ~INV_MPU6050_BIT_I2C_MST_EN; + result = regmap_write(st->map, st->reg->user_ctrl, d); if (result) - goto error_accl_off; + goto error_magn_off; + st->chip_config.user_ctrl = d; result = inv_mpu6050_switch_engine(st, false, INV_MPU6050_BIT_PWR_ACCL_STBY); @@ -90,6 +152,10 @@ static int inv_mpu6050_set_enable(struct iio_dev *indio_dev, bool enable) return 0; +error_magn_off: + /* always restore user_ctrl to disable fifo properly */ + st->chip_config.user_ctrl &= ~INV_MPU6050_BIT_I2C_MST_EN; + regmap_write(st->map, st->reg->user_ctrl, st->chip_config.user_ctrl); error_accl_off: if (st->chip_config.accl_fifo_enable) inv_mpu6050_switch_engine(st, false, diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h index 80e42c7dbcbe..fd02d0e184f3 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h @@ -12,6 +12,7 @@ #define ST_LSM6DSX_H #include <linux/device.h> +#include <linux/iio/iio.h> #define ST_LSM6DS3_DEV_NAME "lsm6ds3" #define ST_LSM6DS3H_DEV_NAME "lsm6ds3h" @@ -54,6 +55,26 @@ enum st_lsm6dsx_hw_id { * ST_LSM6DSX_TAGGED_SAMPLE_SIZE) #define ST_LSM6DSX_SHIFT_VAL(val, mask) (((val) << __ffs(mask)) & (mask)) +#define ST_LSM6DSX_CHANNEL_ACC(chan_type, addr, mod, scan_idx) \ +{ \ + .type = chan_type, \ + .address = addr, \ + .modified = 1, \ + .channel2 = mod, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), \ + .scan_index = scan_idx, \ + .scan_type = { \ + .sign = 's', \ + .realbits = 16, \ + .storagebits = 16, \ + .endianness = IIO_LE, \ + }, \ + .event_spec = &st_lsm6dsx_event, \ + .num_event_specs = 1, \ +} + #define ST_LSM6DSX_CHANNEL(chan_type, addr, mod, scan_idx) \ { \ .type = chan_type, \ @@ -162,6 +183,16 @@ struct st_lsm6dsx_shub_settings { u8 batch_en; }; +struct st_lsm6dsx_event_settings { + struct st_lsm6dsx_reg enable_reg; + struct st_lsm6dsx_reg wakeup_reg; + u8 wakeup_src_reg; + u8 wakeup_src_status_mask; + u8 wakeup_src_z_mask; + u8 wakeup_src_y_mask; + u8 wakeup_src_x_mask; +}; + enum st_lsm6dsx_ext_sensor_id { ST_LSM6DSX_ID_MAGN, }; @@ -215,6 +246,8 @@ struct st_lsm6dsx_ext_dev_settings { * @fs_table: Hw sensors gain table (gain + val). * @decimator: List of decimator register info (addr + mask). * @batch: List of FIFO batching register info (addr + mask). + * @lir: Latched interrupt register info (addr + mask). + * @clear_on_read: Clear on read register info (addr + mask). * @fifo_ops: Sensor hw FIFO parameters. * @ts_settings: Hw timer related settings. * @shub_settings: i2c controller related settings. @@ -223,6 +256,9 @@ struct st_lsm6dsx_settings { u8 wai; u8 int1_addr; u8 int2_addr; + u8 int1_func_addr; + u8 int2_func_addr; + u8 int_func_mask; u8 reset_addr; u16 max_fifo_size; struct { @@ -237,9 +273,12 @@ struct st_lsm6dsx_settings { struct st_lsm6dsx_fs_table_entry fs_table[2]; struct st_lsm6dsx_reg decimator[ST_LSM6DSX_MAX_ID]; struct st_lsm6dsx_reg batch[ST_LSM6DSX_MAX_ID]; + struct st_lsm6dsx_reg lir; + struct st_lsm6dsx_reg clear_on_read; struct st_lsm6dsx_fifo_ops fifo_ops; struct st_lsm6dsx_hw_ts_settings ts_settings; struct st_lsm6dsx_shub_settings shub_settings; + struct st_lsm6dsx_event_settings event_settings; }; enum st_lsm6dsx_sensor_id { @@ -320,6 +359,10 @@ struct st_lsm6dsx_hw { u8 ts_sip; u8 sip; + u8 event_threshold; + u8 enable_event; + struct st_lsm6dsx_reg irq_routing; + u8 *buff; struct iio_dev *iio_devs[ST_LSM6DSX_ID_MAX]; @@ -327,6 +370,13 @@ struct st_lsm6dsx_hw { const struct st_lsm6dsx_settings *settings; }; +static const struct iio_event_spec st_lsm6dsx_event = { + .type = IIO_EV_TYPE_THRESH, + .dir = IIO_EV_DIR_EITHER, + .mask_separate = BIT(IIO_EV_INFO_VALUE) | + BIT(IIO_EV_INFO_ENABLE) +}; + static const unsigned long st_lsm6dsx_available_scan_masks[] = {0x7, 0x0}; extern const struct dev_pm_ops st_lsm6dsx_pm_ops; diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c index b0f3da1976e4..ef579650fd52 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c @@ -30,8 +30,6 @@ * Denis Ciocca <denis.ciocca@st.com> */ #include <linux/module.h> -#include <linux/interrupt.h> -#include <linux/irq.h> #include <linux/iio/kfifo_buf.h> #include <linux/iio/iio.h> #include <linux/iio/buffer.h> @@ -42,10 +40,6 @@ #include "st_lsm6dsx.h" -#define ST_LSM6DSX_REG_HLACTIVE_ADDR 0x12 -#define ST_LSM6DSX_REG_HLACTIVE_MASK BIT(5) -#define ST_LSM6DSX_REG_PP_OD_ADDR 0x12 -#define ST_LSM6DSX_REG_PP_OD_MASK BIT(4) #define ST_LSM6DSX_REG_FIFO_MODE_ADDR 0x0a #define ST_LSM6DSX_FIFO_MODE_MASK GENMASK(2, 0) #define ST_LSM6DSX_FIFO_ODR_MASK GENMASK(6, 3) @@ -654,25 +648,6 @@ out: return err; } -static irqreturn_t st_lsm6dsx_handler_irq(int irq, void *private) -{ - struct st_lsm6dsx_hw *hw = private; - - return hw->sip > 0 ? IRQ_WAKE_THREAD : IRQ_NONE; -} - -static irqreturn_t st_lsm6dsx_handler_thread(int irq, void *private) -{ - struct st_lsm6dsx_hw *hw = private; - int count; - - mutex_lock(&hw->fifo_lock); - count = hw->settings->fifo_ops.read_fifo(hw); - mutex_unlock(&hw->fifo_lock); - - return count ? IRQ_HANDLED : IRQ_NONE; -} - static int st_lsm6dsx_buffer_preenable(struct iio_dev *iio_dev) { struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); @@ -702,59 +677,8 @@ static const struct iio_buffer_setup_ops st_lsm6dsx_buffer_ops = { int st_lsm6dsx_fifo_setup(struct st_lsm6dsx_hw *hw) { - struct device_node *np = hw->dev->of_node; - struct st_sensors_platform_data *pdata; struct iio_buffer *buffer; - unsigned long irq_type; - bool irq_active_low; - int i, err; - - irq_type = irqd_get_trigger_type(irq_get_irq_data(hw->irq)); - - switch (irq_type) { - case IRQF_TRIGGER_HIGH: - case IRQF_TRIGGER_RISING: - irq_active_low = false; - break; - case IRQF_TRIGGER_LOW: - case IRQF_TRIGGER_FALLING: - irq_active_low = true; - break; - default: - dev_info(hw->dev, "mode %lx unsupported\n", irq_type); - return -EINVAL; - } - - err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_HLACTIVE_ADDR, - ST_LSM6DSX_REG_HLACTIVE_MASK, - FIELD_PREP(ST_LSM6DSX_REG_HLACTIVE_MASK, - irq_active_low)); - if (err < 0) - return err; - - pdata = (struct st_sensors_platform_data *)hw->dev->platform_data; - if ((np && of_property_read_bool(np, "drive-open-drain")) || - (pdata && pdata->open_drain)) { - err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_PP_OD_ADDR, - ST_LSM6DSX_REG_PP_OD_MASK, - FIELD_PREP(ST_LSM6DSX_REG_PP_OD_MASK, - 1)); - if (err < 0) - return err; - - irq_type |= IRQF_SHARED; - } - - err = devm_request_threaded_irq(hw->dev, hw->irq, - st_lsm6dsx_handler_irq, - st_lsm6dsx_handler_thread, - irq_type | IRQF_ONESHOT, - "lsm6dsx", hw); - if (err) { - dev_err(hw->dev, "failed to request trigger irq %d\n", - hw->irq); - return err; - } + int i; for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) { if (!hw->iio_devs[i]) diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c index 2d3495560136..8a813ddba19c 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c @@ -48,8 +48,11 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/delay.h> +#include <linux/iio/events.h> #include <linux/iio/iio.h> #include <linux/iio/sysfs.h> +#include <linux/interrupt.h> +#include <linux/irq.h> #include <linux/pm.h> #include <linux/regmap.h> #include <linux/bitfield.h> @@ -65,10 +68,15 @@ #define ST_LSM6DSX_REG_BDU_ADDR 0x12 #define ST_LSM6DSX_REG_BDU_MASK BIT(6) +#define ST_LSM6DSX_REG_HLACTIVE_ADDR 0x12 +#define ST_LSM6DSX_REG_HLACTIVE_MASK BIT(5) +#define ST_LSM6DSX_REG_PP_OD_ADDR 0x12 +#define ST_LSM6DSX_REG_PP_OD_MASK BIT(4) + static const struct iio_chan_spec st_lsm6dsx_acc_channels[] = { - ST_LSM6DSX_CHANNEL(IIO_ACCEL, 0x28, IIO_MOD_X, 0), - ST_LSM6DSX_CHANNEL(IIO_ACCEL, 0x2a, IIO_MOD_Y, 1), - ST_LSM6DSX_CHANNEL(IIO_ACCEL, 0x2c, IIO_MOD_Z, 2), + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, 0x28, IIO_MOD_X, 0), + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, 0x2a, IIO_MOD_Y, 1), + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, 0x2c, IIO_MOD_Z, 2), IIO_CHAN_SOFT_TIMESTAMP(3), }; @@ -161,6 +169,9 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .wai = 0x69, .int1_addr = 0x0d, .int2_addr = 0x0e, + .int1_func_addr = 0x5e, + .int2_func_addr = 0x5f, + .int_func_mask = BIT(5), .reset_addr = 0x12, .max_fifo_size = 1365, .id = { @@ -237,6 +248,10 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = GENMASK(5, 3), }, }, + .lir = { + .addr = 0x58, + .mask = BIT(0), + }, .fifo_ops = { .update_fifo = st_lsm6dsx_update_fifo, .read_fifo = st_lsm6dsx_read_fifo, @@ -268,11 +283,25 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = GENMASK(5, 3), }, }, + .event_settings = { + .wakeup_reg = { + .addr = 0x5B, + .mask = GENMASK(5, 0), + }, + .wakeup_src_reg = 0x1b, + .wakeup_src_status_mask = BIT(3), + .wakeup_src_z_mask = BIT(0), + .wakeup_src_y_mask = BIT(1), + .wakeup_src_x_mask = BIT(2), + }, }, { .wai = 0x69, .int1_addr = 0x0d, .int2_addr = 0x0e, + .int1_func_addr = 0x5e, + .int2_func_addr = 0x5f, + .int_func_mask = BIT(5), .reset_addr = 0x12, .max_fifo_size = 682, .id = { @@ -349,6 +378,10 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = GENMASK(5, 3), }, }, + .lir = { + .addr = 0x58, + .mask = BIT(0), + }, .fifo_ops = { .update_fifo = st_lsm6dsx_update_fifo, .read_fifo = st_lsm6dsx_read_fifo, @@ -380,11 +413,25 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = GENMASK(5, 3), }, }, + .event_settings = { + .wakeup_reg = { + .addr = 0x5B, + .mask = GENMASK(5, 0), + }, + .wakeup_src_reg = 0x1b, + .wakeup_src_status_mask = BIT(3), + .wakeup_src_z_mask = BIT(0), + .wakeup_src_y_mask = BIT(1), + .wakeup_src_x_mask = BIT(2), + }, }, { .wai = 0x6a, .int1_addr = 0x0d, .int2_addr = 0x0e, + .int1_func_addr = 0x5e, + .int2_func_addr = 0x5f, + .int_func_mask = BIT(5), .reset_addr = 0x12, .max_fifo_size = 682, .id = { @@ -470,6 +517,10 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = GENMASK(5, 3), }, }, + .lir = { + .addr = 0x58, + .mask = BIT(0), + }, .fifo_ops = { .update_fifo = st_lsm6dsx_update_fifo, .read_fifo = st_lsm6dsx_read_fifo, @@ -501,6 +552,21 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = GENMASK(5, 3), }, }, + .event_settings = { + .enable_reg = { + .addr = 0x58, + .mask = BIT(7), + }, + .wakeup_reg = { + .addr = 0x5B, + .mask = GENMASK(5, 0), + }, + .wakeup_src_reg = 0x1b, + .wakeup_src_status_mask = BIT(3), + .wakeup_src_z_mask = BIT(0), + .wakeup_src_y_mask = BIT(1), + .wakeup_src_x_mask = BIT(2), + }, }, { .wai = 0x6c, @@ -585,6 +651,14 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = GENMASK(7, 4), }, }, + .lir = { + .addr = 0x56, + .mask = BIT(0), + }, + .clear_on_read = { + .addr = 0x56, + .mask = BIT(6), + }, .fifo_ops = { .update_fifo = st_lsm6dsx_update_fifo, .read_fifo = st_lsm6dsx_read_tagged_fifo, @@ -639,6 +713,9 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .wai = 0x6b, .int1_addr = 0x0d, .int2_addr = 0x0e, + .int1_func_addr = 0x5e, + .int2_func_addr = 0x5f, + .int_func_mask = BIT(5), .reset_addr = 0x12, .max_fifo_size = 512, .id = { @@ -715,6 +792,14 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = GENMASK(7, 4), }, }, + .lir = { + .addr = 0x56, + .mask = BIT(0), + }, + .clear_on_read = { + .addr = 0x56, + .mask = BIT(6), + }, .fifo_ops = { .update_fifo = st_lsm6dsx_update_fifo, .read_fifo = st_lsm6dsx_read_tagged_fifo, @@ -738,11 +823,29 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = GENMASK(7, 6), }, }, + .event_settings = { + .enable_reg = { + .addr = 0x58, + .mask = BIT(7), + }, + .wakeup_reg = { + .addr = 0x5B, + .mask = GENMASK(5, 0), + }, + .wakeup_src_reg = 0x1b, + .wakeup_src_status_mask = BIT(3), + .wakeup_src_z_mask = BIT(0), + .wakeup_src_y_mask = BIT(1), + .wakeup_src_x_mask = BIT(2), + }, }, { .wai = 0x6b, .int1_addr = 0x0d, .int2_addr = 0x0e, + .int1_func_addr = 0x5e, + .int2_func_addr = 0x5f, + .int_func_mask = BIT(5), .reset_addr = 0x12, .max_fifo_size = 512, .id = { @@ -822,6 +925,14 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = GENMASK(7, 4), }, }, + .lir = { + .addr = 0x56, + .mask = BIT(0), + }, + .clear_on_read = { + .addr = 0x56, + .mask = BIT(6), + }, .fifo_ops = { .update_fifo = st_lsm6dsx_update_fifo, .read_fifo = st_lsm6dsx_read_tagged_fifo, @@ -870,6 +981,21 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .slv0_addr = 0x15, .dw_slv0_addr = 0x21, .batch_en = BIT(3), + }, + .event_settings = { + .enable_reg = { + .addr = 0x58, + .mask = BIT(7), + }, + .wakeup_reg = { + .addr = 0x5B, + .mask = GENMASK(5, 0), + }, + .wakeup_src_reg = 0x1b, + .wakeup_src_status_mask = BIT(3), + .wakeup_src_z_mask = BIT(0), + .wakeup_src_y_mask = BIT(1), + .wakeup_src_x_mask = BIT(2), } }, }; @@ -1076,7 +1202,8 @@ static int st_lsm6dsx_read_oneshot(struct st_lsm6dsx_sensor *sensor, if (err < 0) return err; - st_lsm6dsx_sensor_set_enable(sensor, false); + if (!hw->enable_event) + st_lsm6dsx_sensor_set_enable(sensor, false); *val = (s16)le16_to_cpu(data); @@ -1149,6 +1276,139 @@ static int st_lsm6dsx_write_raw(struct iio_dev *iio_dev, return err; } +static int st_lsm6dsx_event_setup(struct st_lsm6dsx_hw *hw, int state) +{ + int err; + u8 enable = 0; + + if (!hw->settings->int1_func_addr) + return -ENOTSUPP; + + enable = state ? hw->settings->event_settings.enable_reg.mask : 0; + + err = regmap_update_bits(hw->regmap, + hw->settings->event_settings.enable_reg.addr, + hw->settings->event_settings.enable_reg.mask, + enable); + if (err < 0) + return err; + + enable = state ? hw->irq_routing.mask : 0; + + /* Enable wakeup interrupt */ + return regmap_update_bits(hw->regmap, hw->irq_routing.addr, + hw->irq_routing.mask, + enable); +} + +static int st_lsm6dsx_read_event(struct iio_dev *iio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + enum iio_event_info info, + int *val, int *val2) +{ + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); + struct st_lsm6dsx_hw *hw = sensor->hw; + + if (type != IIO_EV_TYPE_THRESH) + return -EINVAL; + + *val2 = 0; + *val = hw->event_threshold; + + return IIO_VAL_INT; +} + +static int st_lsm6dsx_write_event(struct iio_dev *iio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + enum iio_event_info info, + int val, int val2) +{ + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); + struct st_lsm6dsx_hw *hw = sensor->hw; + int err; + + if (type != IIO_EV_TYPE_THRESH) + return -EINVAL; + + if (val < 0 || val > 31) + return -EINVAL; + + err = regmap_update_bits(hw->regmap, + hw->settings->event_settings.wakeup_reg.addr, + hw->settings->event_settings.wakeup_reg.mask, + val); + if (err) + return -EINVAL; + + hw->event_threshold = val; + + return 0; +} + +static int st_lsm6dsx_read_event_config(struct iio_dev *iio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir) +{ + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); + struct st_lsm6dsx_hw *hw = sensor->hw; + + if (type != IIO_EV_TYPE_THRESH) + return -EINVAL; + + return !!(hw->enable_event & BIT(chan->channel2)); +} + +static int st_lsm6dsx_write_event_config(struct iio_dev *iio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + int state) +{ + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); + struct st_lsm6dsx_hw *hw = sensor->hw; + u8 enable_event; + int err = 0; + + if (type != IIO_EV_TYPE_THRESH) + return -EINVAL; + + if (state) { + enable_event = hw->enable_event | BIT(chan->channel2); + + /* do not enable events if they are already enabled */ + if (hw->enable_event) + goto out; + } else { + enable_event = hw->enable_event & ~BIT(chan->channel2); + + /* only turn off sensor if no events is enabled */ + if (enable_event) + goto out; + } + + /* stop here if no changes have been made */ + if (hw->enable_event == enable_event) + return 0; + + err = st_lsm6dsx_event_setup(hw, state); + if (err < 0) + return err; + + err = st_lsm6dsx_sensor_set_enable(sensor, state); + if (err < 0) + return err; + +out: + hw->enable_event = enable_event; + + return 0; +} + int st_lsm6dsx_set_watermark(struct iio_dev *iio_dev, unsigned int val) { struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); @@ -1233,6 +1493,10 @@ static const struct iio_info st_lsm6dsx_acc_info = { .attrs = &st_lsm6dsx_acc_attribute_group, .read_raw = st_lsm6dsx_read_raw, .write_raw = st_lsm6dsx_write_raw, + .read_event_value = st_lsm6dsx_read_event, + .write_event_value = st_lsm6dsx_write_event, + .read_event_config = st_lsm6dsx_read_event_config, + .write_event_config = st_lsm6dsx_write_event_config, .hwfifo_set_watermark = st_lsm6dsx_set_watermark, }; @@ -1278,9 +1542,13 @@ static int st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw, u8 *drdy_reg) switch (drdy_pin) { case 1: *drdy_reg = hw->settings->int1_addr; + hw->irq_routing.addr = hw->settings->int1_func_addr; + hw->irq_routing.mask = hw->settings->int_func_mask; break; case 2: *drdy_reg = hw->settings->int2_addr; + hw->irq_routing.addr = hw->settings->int2_func_addr; + hw->irq_routing.mask = hw->settings->int_func_mask; break; default: dev_err(hw->dev, "unsupported data ready pin\n"); @@ -1416,6 +1684,29 @@ static int st_lsm6dsx_init_device(struct st_lsm6dsx_hw *hw) if (err < 0) return err; + /* enable Latched interrupts for device events */ + if (hw->settings->lir.addr) { + unsigned int data; + + data = ST_LSM6DSX_SHIFT_VAL(1, hw->settings->lir.mask); + err = regmap_update_bits(hw->regmap, hw->settings->lir.addr, + hw->settings->lir.mask, data); + if (err < 0) + return err; + + /* enable clear on read for latched interrupts */ + if (hw->settings->clear_on_read.addr) { + data = ST_LSM6DSX_SHIFT_VAL(1, + hw->settings->clear_on_read.mask); + err = regmap_update_bits(hw->regmap, + hw->settings->clear_on_read.addr, + hw->settings->clear_on_read.mask, + data); + if (err < 0) + return err; + } + } + err = st_lsm6dsx_init_shub(hw); if (err < 0) return err; @@ -1466,6 +1757,123 @@ static struct iio_dev *st_lsm6dsx_alloc_iiodev(struct st_lsm6dsx_hw *hw, return iio_dev; } +static void st_lsm6dsx_report_motion_event(struct st_lsm6dsx_hw *hw, int data) +{ + s64 timestamp = iio_get_time_ns(hw->iio_devs[ST_LSM6DSX_ID_ACC]); + + if ((data & hw->settings->event_settings.wakeup_src_z_mask) && + (hw->enable_event & BIT(IIO_MOD_Z))) + iio_push_event(hw->iio_devs[ST_LSM6DSX_ID_ACC], + IIO_MOD_EVENT_CODE(IIO_ACCEL, + 0, + IIO_MOD_Z, + IIO_EV_TYPE_THRESH, + IIO_EV_DIR_EITHER), + timestamp); + + if ((data & hw->settings->event_settings.wakeup_src_y_mask) && + (hw->enable_event & BIT(IIO_MOD_Y))) + iio_push_event(hw->iio_devs[ST_LSM6DSX_ID_ACC], + IIO_MOD_EVENT_CODE(IIO_ACCEL, + 0, + IIO_MOD_Y, + IIO_EV_TYPE_THRESH, + IIO_EV_DIR_EITHER), + timestamp); + + if ((data & hw->settings->event_settings.wakeup_src_x_mask) && + (hw->enable_event & BIT(IIO_MOD_X))) + iio_push_event(hw->iio_devs[ST_LSM6DSX_ID_ACC], + IIO_MOD_EVENT_CODE(IIO_ACCEL, + 0, + IIO_MOD_X, + IIO_EV_TYPE_THRESH, + IIO_EV_DIR_EITHER), + timestamp); +} + +static irqreturn_t st_lsm6dsx_handler_thread(int irq, void *private) +{ + struct st_lsm6dsx_hw *hw = private; + int count; + int data, err; + + if (hw->enable_event) { + err = regmap_read(hw->regmap, + hw->settings->event_settings.wakeup_src_reg, + &data); + if (err < 0) + return IRQ_NONE; + + if (data & hw->settings->event_settings.wakeup_src_status_mask) + st_lsm6dsx_report_motion_event(hw, data); + } + + mutex_lock(&hw->fifo_lock); + count = hw->settings->fifo_ops.read_fifo(hw); + mutex_unlock(&hw->fifo_lock); + + return count ? IRQ_HANDLED : IRQ_NONE; +} + +static int st_lsm6dsx_irq_setup(struct st_lsm6dsx_hw *hw) +{ + struct st_sensors_platform_data *pdata; + struct device_node *np = hw->dev->of_node; + unsigned long irq_type; + bool irq_active_low; + int err; + + irq_type = irqd_get_trigger_type(irq_get_irq_data(hw->irq)); + + switch (irq_type) { + case IRQF_TRIGGER_HIGH: + case IRQF_TRIGGER_RISING: + irq_active_low = false; + break; + case IRQF_TRIGGER_LOW: + case IRQF_TRIGGER_FALLING: + irq_active_low = true; + break; + default: + dev_info(hw->dev, "mode %lx unsupported\n", irq_type); + return -EINVAL; + } + + err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_HLACTIVE_ADDR, + ST_LSM6DSX_REG_HLACTIVE_MASK, + FIELD_PREP(ST_LSM6DSX_REG_HLACTIVE_MASK, + irq_active_low)); + if (err < 0) + return err; + + pdata = (struct st_sensors_platform_data *)hw->dev->platform_data; + if ((np && of_property_read_bool(np, "drive-open-drain")) || + (pdata && pdata->open_drain)) { + err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_PP_OD_ADDR, + ST_LSM6DSX_REG_PP_OD_MASK, + FIELD_PREP(ST_LSM6DSX_REG_PP_OD_MASK, + 1)); + if (err < 0) + return err; + + irq_type |= IRQF_SHARED; + } + + err = devm_request_threaded_irq(hw->dev, hw->irq, + NULL, + st_lsm6dsx_handler_thread, + irq_type | IRQF_ONESHOT, + "lsm6dsx", hw); + if (err) { + dev_err(hw->dev, "failed to request trigger irq %d\n", + hw->irq); + return err; + } + + return 0; +} + int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id, struct regmap *regmap) { @@ -1514,6 +1922,10 @@ int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id, } if (hw->irq > 0) { + err = st_lsm6dsx_irq_setup(hw); + if (err < 0) + return err; + err = st_lsm6dsx_fifo_setup(hw); if (err < 0) return err; @@ -1528,6 +1940,9 @@ int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id, return err; } + if (dev->of_node && of_property_read_bool(dev->of_node, "wakeup-source")) + device_init_wakeup(dev, true); + return 0; } EXPORT_SYMBOL(st_lsm6dsx_probe); @@ -1546,6 +1961,13 @@ static int __maybe_unused st_lsm6dsx_suspend(struct device *dev) if (!(hw->enable_mask & BIT(sensor->id))) continue; + if (device_may_wakeup(dev) && + sensor->id == ST_LSM6DSX_ID_ACC && hw->enable_event) { + /* Enable wake from IRQ */ + enable_irq_wake(hw->irq); + continue; + } + if (sensor->id == ST_LSM6DSX_ID_EXT0 || sensor->id == ST_LSM6DSX_ID_EXT1 || sensor->id == ST_LSM6DSX_ID_EXT2) @@ -1575,6 +1997,10 @@ static int __maybe_unused st_lsm6dsx_resume(struct device *dev) continue; sensor = iio_priv(hw->iio_devs[i]); + if (device_may_wakeup(dev) && + sensor->id == ST_LSM6DSX_ID_ACC && hw->enable_event) + disable_irq_wake(hw->irq); + if (!(hw->suspend_mask & BIT(sensor->id))) continue; diff --git a/drivers/iio/industrialio-core.c b/drivers/iio/industrialio-core.c index 524a686077ca..f72c2dc5f703 100644 --- a/drivers/iio/industrialio-core.c +++ b/drivers/iio/industrialio-core.c @@ -1238,6 +1238,16 @@ static ssize_t iio_show_dev_name(struct device *dev, static DEVICE_ATTR(name, S_IRUGO, iio_show_dev_name, NULL); +static ssize_t iio_show_dev_label(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct iio_dev *indio_dev = dev_to_iio_dev(dev); + return snprintf(buf, PAGE_SIZE, "%s\n", indio_dev->label); +} + +static DEVICE_ATTR(label, S_IRUGO, iio_show_dev_label, NULL); + static ssize_t iio_show_timestamp_clock(struct device *dev, struct device_attribute *attr, char *buf) @@ -1354,6 +1364,8 @@ static int iio_device_register_sysfs(struct iio_dev *indio_dev) if (indio_dev->name) attrcount++; + if (indio_dev->label) + attrcount++; if (clk) attrcount++; @@ -1376,6 +1388,8 @@ static int iio_device_register_sysfs(struct iio_dev *indio_dev) indio_dev->chan_attr_group.attrs[attrn++] = &p->dev_attr.attr; if (indio_dev->name) indio_dev->chan_attr_group.attrs[attrn++] = &dev_attr_name.attr; + if (indio_dev->label) + indio_dev->chan_attr_group.attrs[attrn++] = &dev_attr_label.attr; if (clk) indio_dev->chan_attr_group.attrs[attrn++] = clk; @@ -1647,6 +1661,9 @@ int __iio_device_register(struct iio_dev *indio_dev, struct module *this_mod) if (!indio_dev->dev.of_node && indio_dev->dev.parent) indio_dev->dev.of_node = indio_dev->dev.parent->of_node; + indio_dev->label = of_get_property(indio_dev->dev.of_node, "label", + NULL); + ret = iio_check_unique_scan_index(indio_dev); if (ret < 0) return ret; diff --git a/drivers/iio/light/bh1750.c b/drivers/iio/light/bh1750.c index 28347df78cff..adb5ab9e3439 100644 --- a/drivers/iio/light/bh1750.c +++ b/drivers/iio/light/bh1750.c @@ -59,9 +59,9 @@ struct bh1750_chip_info { u16 int_time_low_mask; u16 int_time_high_mask; -} +}; -static const bh1750_chip_info_tbl[] = { +static const struct bh1750_chip_info bh1750_chip_info_tbl[] = { [BH1710] = { 140, 1022, 300, 400, 250000000, 2, 0x001F, 0x03E0 }, [BH1721] = { 140, 1020, 300, 400, 250000000, 2, 0x0010, 0x03E0 }, [BH1750] = { 31, 254, 69, 1740, 57500000, 1, 0x001F, 0x00E0 }, diff --git a/drivers/iio/light/cm36651.c b/drivers/iio/light/cm36651.c index 1019d625adb1..90e38fcc974b 100644 --- a/drivers/iio/light/cm36651.c +++ b/drivers/iio/light/cm36651.c @@ -532,7 +532,7 @@ static int cm36651_write_prox_event_config(struct iio_dev *indio_dev, int state) { struct cm36651_data *cm36651 = iio_priv(indio_dev); - int cmd, ret = -EINVAL; + int cmd, ret; mutex_lock(&cm36651->lock); diff --git a/drivers/iio/light/tcs3414.c b/drivers/iio/light/tcs3414.c index 7c0291c5fe76..b542e5619ead 100644 --- a/drivers/iio/light/tcs3414.c +++ b/drivers/iio/light/tcs3414.c @@ -240,32 +240,42 @@ static const struct iio_info tcs3414_info = { .attrs = &tcs3414_attribute_group, }; -static int tcs3414_buffer_preenable(struct iio_dev *indio_dev) +static int tcs3414_buffer_postenable(struct iio_dev *indio_dev) { struct tcs3414_data *data = iio_priv(indio_dev); + int ret; + + ret = iio_triggered_buffer_postenable(indio_dev); + if (ret) + return ret; data->control |= TCS3414_CONTROL_ADC_EN; - return i2c_smbus_write_byte_data(data->client, TCS3414_CONTROL, + ret = i2c_smbus_write_byte_data(data->client, TCS3414_CONTROL, data->control); + if (ret) + iio_triggered_buffer_predisable(indio_dev); + + return ret; } static int tcs3414_buffer_predisable(struct iio_dev *indio_dev) { struct tcs3414_data *data = iio_priv(indio_dev); - int ret; - - ret = iio_triggered_buffer_predisable(indio_dev); - if (ret < 0) - return ret; + int ret, ret2; data->control &= ~TCS3414_CONTROL_ADC_EN; - return i2c_smbus_write_byte_data(data->client, TCS3414_CONTROL, + ret = i2c_smbus_write_byte_data(data->client, TCS3414_CONTROL, data->control); + + ret2 = iio_triggered_buffer_predisable(indio_dev); + if (!ret) + ret = ret2; + + return ret; } static const struct iio_buffer_setup_ops tcs3414_buffer_setup_ops = { - .preenable = tcs3414_buffer_preenable, - .postenable = &iio_triggered_buffer_postenable, + .postenable = tcs3414_buffer_postenable, .predisable = tcs3414_buffer_predisable, }; diff --git a/drivers/iio/pressure/bmp280-core.c b/drivers/iio/pressure/bmp280-core.c index 8d0f15f27dc5..c3b5c1f6614d 100644 --- a/drivers/iio/pressure/bmp280-core.c +++ b/drivers/iio/pressure/bmp280-core.c @@ -1130,7 +1130,6 @@ int bmp280_common_probe(struct device *dev, if (ret) goto out_runtime_pm_disable; - return 0; out_runtime_pm_disable: diff --git a/drivers/iio/proximity/sx9500.c b/drivers/iio/proximity/sx9500.c index 612f79c53cfc..287d288e40c2 100644 --- a/drivers/iio/proximity/sx9500.c +++ b/drivers/iio/proximity/sx9500.c @@ -675,11 +675,15 @@ out: return IRQ_HANDLED; } -static int sx9500_buffer_preenable(struct iio_dev *indio_dev) +static int sx9500_buffer_postenable(struct iio_dev *indio_dev) { struct sx9500_data *data = iio_priv(indio_dev); int ret = 0, i; + ret = iio_triggered_buffer_postenable(indio_dev); + if (ret) + return ret; + mutex_lock(&data->mutex); for (i = 0; i < SX9500_NUM_CHANNELS; i++) @@ -696,6 +700,9 @@ static int sx9500_buffer_preenable(struct iio_dev *indio_dev) mutex_unlock(&data->mutex); + if (ret) + iio_triggered_buffer_predisable(indio_dev); + return ret; } @@ -704,8 +711,6 @@ static int sx9500_buffer_predisable(struct iio_dev *indio_dev) struct sx9500_data *data = iio_priv(indio_dev); int ret = 0, i; - iio_triggered_buffer_predisable(indio_dev); - mutex_lock(&data->mutex); for (i = 0; i < SX9500_NUM_CHANNELS; i++) @@ -722,12 +727,13 @@ static int sx9500_buffer_predisable(struct iio_dev *indio_dev) mutex_unlock(&data->mutex); + iio_triggered_buffer_predisable(indio_dev); + return ret; } static const struct iio_buffer_setup_ops sx9500_buffer_setup_ops = { - .preenable = sx9500_buffer_preenable, - .postenable = iio_triggered_buffer_postenable, + .postenable = sx9500_buffer_postenable, .predisable = sx9500_buffer_predisable, }; diff --git a/drivers/iio/temperature/max31856.c b/drivers/iio/temperature/max31856.c index f184ba5601d9..73ed550e3fc9 100644 --- a/drivers/iio/temperature/max31856.c +++ b/drivers/iio/temperature/max31856.c @@ -284,6 +284,8 @@ static int max31856_probe(struct spi_device *spi) spi_set_drvdata(spi, indio_dev); indio_dev->info = &max31856_info; + indio_dev->dev.parent = &spi->dev; + indio_dev->dev.of_node = spi->dev.of_node; indio_dev->name = id->name; indio_dev->modes = INDIO_DIRECT_MODE; indio_dev->channels = max31856_channels; diff --git a/drivers/staging/iio/accel/adis16240.c b/drivers/staging/iio/accel/adis16240.c index 82099db4bf0c..a480409090c0 100644 --- a/drivers/staging/iio/accel/adis16240.c +++ b/drivers/staging/iio/accel/adis16240.c @@ -7,7 +7,6 @@ #include <linux/interrupt.h> #include <linux/irq.h> -#include <linux/gpio.h> #include <linux/delay.h> #include <linux/device.h> #include <linux/kernel.h> diff --git a/drivers/staging/iio/adc/ad7192.c b/drivers/staging/iio/adc/ad7192.c index e6b660489165..bf3e2a9cc07f 100644 --- a/drivers/staging/iio/adc/ad7192.c +++ b/drivers/staging/iio/adc/ad7192.c @@ -155,6 +155,11 @@ * The DOUT/RDY output must also be wired to an interrupt capable GPIO. */ +enum { + AD7192_SYSCALIB_ZERO_SCALE, + AD7192_SYSCALIB_FULL_SCALE, +}; + struct ad7192_state { struct regulator *avdd; struct regulator *dvdd; @@ -169,10 +174,80 @@ struct ad7192_state { u8 devid; u8 clock_sel; struct mutex lock; /* protect sensor state */ + u8 syscalib_mode[8]; struct ad_sigma_delta sd; }; +static const char * const ad7192_syscalib_modes[] = { + [AD7192_SYSCALIB_ZERO_SCALE] = "zero_scale", + [AD7192_SYSCALIB_FULL_SCALE] = "full_scale", +}; + +static int ad7192_set_syscalib_mode(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + unsigned int mode) +{ + struct ad7192_state *st = iio_priv(indio_dev); + + st->syscalib_mode[chan->channel] = mode; + + return 0; +} + +static int ad7192_get_syscalib_mode(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan) +{ + struct ad7192_state *st = iio_priv(indio_dev); + + return st->syscalib_mode[chan->channel]; +} + +static ssize_t ad7192_write_syscalib(struct iio_dev *indio_dev, + uintptr_t private, + const struct iio_chan_spec *chan, + const char *buf, size_t len) +{ + struct ad7192_state *st = iio_priv(indio_dev); + bool sys_calib; + int ret, temp; + + ret = strtobool(buf, &sys_calib); + if (ret) + return ret; + + temp = st->syscalib_mode[chan->channel]; + if (sys_calib) { + if (temp == AD7192_SYSCALIB_ZERO_SCALE) + ret = ad_sd_calibrate(&st->sd, AD7192_MODE_CAL_SYS_ZERO, + chan->address); + else + ret = ad_sd_calibrate(&st->sd, AD7192_MODE_CAL_SYS_FULL, + chan->address); + } + + return ret ? ret : len; +} + +static const struct iio_enum ad7192_syscalib_mode_enum = { + .items = ad7192_syscalib_modes, + .num_items = ARRAY_SIZE(ad7192_syscalib_modes), + .set = ad7192_set_syscalib_mode, + .get = ad7192_get_syscalib_mode +}; + +static const struct iio_chan_spec_ext_info ad7192_calibsys_ext_info[] = { + { + .name = "sys_calibration", + .write = ad7192_write_syscalib, + .shared = IIO_SEPARATE, + }, + IIO_ENUM("sys_calibration_mode", IIO_SEPARATE, + &ad7192_syscalib_mode_enum), + IIO_ENUM_AVAILABLE("sys_calibration_mode", &ad7192_syscalib_mode_enum), + {} +}; + static struct ad7192_state *ad_sigma_delta_to_ad7192(struct ad_sigma_delta *sd) { return container_of(sd, struct ad7192_state, sd); @@ -770,9 +845,11 @@ static int ad7192_channels_config(struct iio_dev *indio_dev) *chan = channels[i]; chan->info_mask_shared_by_all |= BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY); - if (chan->type != IIO_TEMP) + if (chan->type != IIO_TEMP) { chan->info_mask_shared_by_type_available |= BIT(IIO_CHAN_INFO_SCALE); + chan->ext_info = ad7192_calibsys_ext_info; + } chan++; } diff --git a/include/dt-bindings/iio/adc/ingenic,adc.h b/include/dt-bindings/iio/adc/ingenic,adc.h index 82706b2706ac..42f871ab3272 100644 --- a/include/dt-bindings/iio/adc/ingenic,adc.h +++ b/include/dt-bindings/iio/adc/ingenic,adc.h @@ -6,5 +6,6 @@ /* ADC channel idx. */ #define INGENIC_ADC_AUX 0 #define INGENIC_ADC_BATTERY 1 +#define INGENIC_ADC_AUX2 2 #endif diff --git a/include/linux/iio/adc/ad_sigma_delta.h b/include/linux/iio/adc/ad_sigma_delta.h index 7716fa0c9fce..8a4e25a7080c 100644 --- a/include/linux/iio/adc/ad_sigma_delta.h +++ b/include/linux/iio/adc/ad_sigma_delta.h @@ -119,6 +119,8 @@ int ad_sd_reset(struct ad_sigma_delta *sigma_delta, int ad_sigma_delta_single_conversion(struct iio_dev *indio_dev, const struct iio_chan_spec *chan, int *val); +int ad_sd_calibrate(struct ad_sigma_delta *sigma_delta, + unsigned int mode, unsigned int channel); int ad_sd_calibrate_all(struct ad_sigma_delta *sigma_delta, const struct ad_sd_calib_data *cd, unsigned int n); int ad_sd_init(struct ad_sigma_delta *sigma_delta, struct iio_dev *indio_dev, diff --git a/include/linux/iio/iio.h b/include/linux/iio/iio.h index 8e132cf819e4..862ce0019eba 100644 --- a/include/linux/iio/iio.h +++ b/include/linux/iio/iio.h @@ -510,6 +510,7 @@ struct iio_buffer_setup_ops { * attributes * @chan_attr_group: [INTERN] group for all attrs in base directory * @name: [DRIVER] name of the device. + * @label: [DRIVER] unique name to identify which device this is * @info: [DRIVER] callbacks and constant info from driver * @clock_id: [INTERN] timestamping clock posix identifier * @info_exist_lock: [INTERN] lock to prevent use during removal @@ -553,6 +554,7 @@ struct iio_dev { struct list_head channel_attr_list; struct attribute_group chan_attr_group; const char *name; + const char *label; const struct iio_info *info; clockid_t clock_id; struct mutex info_exist_lock; |