1 files changed, 0 insertions, 87 deletions
diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
deleted file mode 100644
index 6d1c0988cfc7..000000000000
--- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
+++ /dev/null
@@ -1,87 +0,0 @@
-* Samsung Exynos specific extensions to the Synopsis Designware Mobile
-  Storage Host Controller
-
-The Synopsis designware mobile storage host controller is used to interface
-a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
-differences between the core Synopsis dw mshc controller properties described
-by synopsis-dw-mshc.txt and the properties used by the Samsung Exynos specific
-extensions to the Synopsis Designware Mobile Storage Host Controller.
-
-Required Properties:
-
-* compatible: should be
-	- "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210
-	  specific extensions.
-	- "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412
-	  specific extensions.
-	- "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250
-	  specific extensions.
-
-* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface
-  unit (ciu) clock. This property is applicable only for Exynos5 SoC's and
-  ignored for Exynos4 SoC's. The valid range of divider value is 0 to 7.
-
-* samsung,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value
-  in transmit mode and CIU clock phase shift value in receive mode for single
-  data rate mode operation. Refer notes below for the order of the cells and the
-  valid values.
-
-* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value
-  in transmit mode and CIU clock phase shift value in receive mode for double
-  data rate mode operation. Refer notes below for the order of the cells and the
-  valid values.
-
-  Notes for the sdr-timing and ddr-timing values:
-
-    The order of the cells should be
-      - First Cell: CIU clock phase shift value for tx mode.
-      - Second Cell: CIU clock phase shift value for rx mode.
-
-    Valid values for SDR and DDR CIU clock timing for Exynos5250:
-      - valid value for tx phase shift and rx phase shift is 0 to 7.
-      - when CIU clock divider value is set to 3, all possible 8 phase shift
-        values can be used.
-      - if CIU clock divider value is 0 (that is divide by 1), both tx and rx
-        phase shift clocks should be 0.
-
-Required properties for a slot:
-
-* gpios: specifies a list of gpios used for command, clock and data bus. The
-  first gpio is the command line and the second gpio is the clock line. The
-  rest of the gpios (depending on the bus-width property) are the data lines in
-  no particular order. The format of the gpio specifier depends on the gpio
-  controller.
-
-Example:
-
-  The MSHC controller node can be split into two portions, SoC specific and
-  board specific portions as listed below.
-
-	dwmmc0@12200000 {
-		compatible = "samsung,exynos5250-dw-mshc";
-		reg = <0x12200000 0x1000>;
-		interrupts = <0 75 0>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-	};
-
-	dwmmc0@12200000 {
-		num-slots = <1>;
-		supports-highspeed;
-		broken-cd;
-		fifo-depth = <0x80>;
-		card-detect-delay = <200>;
-		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3>;
-		samsung,dw-mshc-ddr-timing = <1 2>;
-
-		slot@0 {
-			reg = <0>;
-			bus-width = <8>;
-			gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
-				<&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
-				<&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
-				<&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
-				<&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
-		};
-	};