diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml | 100 |
1 files changed, 90 insertions, 10 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml index 0b8a05dd52e6..607b7fe8d28e 100644 --- a/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml +++ b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/net/dsa/nxp,sja1105.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: NXP SJA1105 Automotive Ethernet Switch Family Device Tree Bindings +title: NXP SJA1105 Automotive Ethernet Switch Family description: The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944.pdf) of at @@ -12,9 +12,6 @@ description: cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed depends on the SPI bus master driver. -allOf: - - $ref: "dsa.yaml#" - maintainers: - Vladimir Oltean <vladimir.oltean@nxp.com> @@ -35,6 +32,21 @@ properties: reg: maxItems: 1 + reset-gpios: + description: + A GPIO connected to the active-low RST_N pin of the SJA1105. Note that + reset of this chip is performed via SPI and the RST_N pin must be wired + to satisfy the power-up sequence documented in "SJA1105PQRS Application + Hints" (AH1704) sec. 2.4.4. Connecting the SJA1105 RST_N pin to a GPIO is + therefore discouraged. + maxItems: 1 + + clocks: + maxItems: 1 + + spi-cpha: true + spi-cpol: true + # Optional container node for the 2 internal MDIO buses of the SJA1110 # (one for the internal 100base-T1 PHYs and the other for the single # 100base-TX PHY). The "reg" property does not have physical significance. @@ -43,6 +55,7 @@ properties: # PHY 1. mdios: type: object + additionalProperties: false properties: '#address-cells': @@ -52,10 +65,8 @@ properties: patternProperties: "^mdio@[0-1]$": - type: object - - allOf: - - $ref: "http://devicetree.org/schemas/net/mdio.yaml#" + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false properties: compatible: @@ -67,17 +78,74 @@ properties: reg: oneOf: - enum: - - 0 - - 1 + - 0 + - 1 required: - compatible - reg +patternProperties: + "^(ethernet-)?ports$": + additionalProperties: true + patternProperties: + "^(ethernet-)?port@[0-9]$": + allOf: + - if: + properties: + phy-mode: + contains: + enum: + - rgmii + - rgmii-rxid + - rgmii-txid + - rgmii-id + then: + properties: + rx-internal-delay-ps: + $ref: "#/$defs/internal-delay-ps" + tx-internal-delay-ps: + $ref: "#/$defs/internal-delay-ps" + required: - compatible - reg +$defs: + internal-delay-ps: + description: + Disable tunable delay lines using 0 ps, or enable them and select + the phase between 1640 ps (73.8 degree shift at 1Gbps) and 2260 ps + (101.7 degree shift) in increments of 0.9 degrees (20 ps). + enum: + [0, 1640, 1660, 1680, 1700, 1720, 1740, 1760, 1780, 1800, 1820, 1840, + 1860, 1880, 1900, 1920, 1940, 1960, 1980, 2000, 2020, 2040, 2060, 2080, + 2100, 2120, 2140, 2160, 2180, 2200, 2220, 2240, 2260] + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + - $ref: /schemas/spi/spi-peripheral-props.yaml# + - if: + properties: + compatible: + enum: + - nxp,sja1105e + - nxp,sja1105p + - nxp,sja1105q + - nxp,sja1105r + - nxp,sja1105s + - nxp,sja1105t + then: + properties: + spi-cpol: false + required: + - spi-cpha + else: + properties: + spi-cpha: false + required: + - spi-cpol + unevaluatedProperties: false examples: @@ -89,6 +157,7 @@ examples: ethernet-switch@1 { reg = <0x1>; compatible = "nxp,sja1105t"; + spi-cpha; ethernet-ports { #address-cells = <1>; @@ -97,29 +166,40 @@ examples: port@0 { phy-handle = <&rgmii_phy6>; phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; reg = <0>; }; port@1 { phy-handle = <&rgmii_phy3>; phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; reg = <1>; }; port@2 { phy-handle = <&rgmii_phy4>; phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; reg = <2>; }; port@3 { + phy-handle = <&rgmii_phy4>; phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; reg = <3>; }; port@4 { ethernet = <&enet2>; phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; reg = <4>; fixed-link { |