diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/sff,sfp.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/net/sff,sfp.yaml | 23 |
1 files changed, 12 insertions, 11 deletions
diff --git a/Documentation/devicetree/bindings/net/sff,sfp.yaml b/Documentation/devicetree/bindings/net/sff,sfp.yaml index 06c66ab81c01..15616ad737f5 100644 --- a/Documentation/devicetree/bindings/net/sff,sfp.yaml +++ b/Documentation/devicetree/bindings/net/sff,sfp.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/net/sff,sfp.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/net/sff,sfp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP) Transceiver @@ -22,45 +22,46 @@ properties: phandle of an I2C bus controller for the SFP two wire serial maximum-power-milliwatt: - maxItems: 1 + minimum: 1000 + default: 1000 description: Maximum module power consumption Specifies the maximum power consumption allowable by a module in the slot, in milli-Watts. Presently, modules can be up to 1W, 1.5W or 2W. - "mod-def0-gpios": + mod-def0-gpios: maxItems: 1 description: GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) module presence input gpio signal, active (module absent) high. Must not be present for SFF modules - "los-gpios": + los-gpios: maxItems: 1 description: GPIO phandle and a specifier of the Receiver Loss of Signal Indication input gpio signal, active (signal lost) high - "tx-fault-gpios": + tx-fault-gpios: maxItems: 1 description: GPIO phandle and a specifier of the Module Transmitter Fault input gpio signal, active (fault condition) high - "tx-disable-gpios": + tx-disable-gpios: maxItems: 1 description: GPIO phandle and a specifier of the Transmitter Disable output gpio signal, active (Tx disable) high - "rate-select0-gpios": + rate-select0-gpios: maxItems: 1 description: GPIO phandle and a specifier of the Rx Signaling Rate Select (AKA RS0) output gpio signal, low - low Rx rate, high - high Rx rate Must not be present for SFF modules - "rate-select1-gpios": + rate-select1-gpios: maxItems: 1 description: GPIO phandle and a specifier of the Tx Signaling Rate Select (AKA RS1) @@ -119,7 +120,7 @@ examples: pinctrl-names = "default"; pinctrl-0 = <&cps_sfpp0_pins>; tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>; - tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>; }; mdio { @@ -131,7 +132,7 @@ examples: pinctrl-names = "default"; pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>; reg = <0>; - interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>; + interrupts = <18 IRQ_TYPE_EDGE_FALLING>; sfp = <&sfp2>; }; }; |