diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
7 files changed, 133 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt b/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt index 188c8bd4eb67..5a0111d4de58 100644 --- a/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt +++ b/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Should be one of the following: - "microchip,mcp2510" for MCP2510. - "microchip,mcp2515" for MCP2515. + - "microchip,mcp25625" for MCP25625. - reg: SPI chip select. - clocks: The clock feeding the CAN controller. - interrupts: Should contain IRQ line for the CAN controller. diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt index e7db7268fd0f..4ac21cef370e 100644 --- a/Documentation/devicetree/bindings/net/dsa/ksz.txt +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -16,6 +16,8 @@ Required properties: Optional properties: - reset-gpios : Should be a gpio specifier for a reset line +- microchip,synclko-125 : Set if the output SYNCLKO frequency should be set to + 125MHz instead of 25MHz. See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required and optional properties. diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt index 6262c2f293b0..24f11e042f8d 100644 --- a/Documentation/devicetree/bindings/net/keystone-netcp.txt +++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt @@ -104,6 +104,23 @@ Required properties: - 10Gb mac<->mac forced mode : 11 ----phy-handle: phandle to PHY device +- cpts: sub-node time synchronization (CPTS) submodule configuration +-- clocks: CPTS reference clock. Should point on cpts-refclk-mux clock. +-- clock-names: should be "cpts" +-- cpts-refclk-mux: multiplexer clock definition sub-node for CPTS reference (RFTCLK) clock +--- #clock-cells: should be 0 +--- clocks: list of CPTS reference (RFTCLK) clock's parents as defined in Data manual +--- ti,mux-tbl: array of multiplexer indexes as defined in Data manual +--- assigned-clocks: should point on cpts-refclk-mux clock +--- assigned-clock-parents: should point on required RFTCLK clock parent to be selected +-- cpts_clock_mult: (optional) Numerator to convert input clock ticks + into nanoseconds +-- cpts_clock_shift: (optional) Denominator to convert input clock ticks into + nanoseconds. + Mult and shift will be calculated basing on CPTS + rftclk frequency if both cpts_clock_shift and + cpts_clock_mult properties are not provided. + Optional properties: - enable-ale: NetCP driver keeps the address learning feature in the ethernet switch module disabled. This attribute is to enable the address @@ -168,6 +185,23 @@ netcp: netcp@2000000 { tx-queue = <648>; tx-channel = <8>; + cpts { + clocks = <&cpts_refclk_mux>; + clock-names = "cpts"; + + cpts_refclk_mux: cpts-refclk-mux { + #clock-cells = <0>; + clocks = <&chipclk12>, <&chipclk13>, + <&timi0>, <&timi1>, + <&tsipclka>, <&tsrefclk>, + <&tsipclkb>; + ti,mux-tbl = <0x0>, <0x1>, <0x2>, + <0x3>, <0x4>, <0x8>, <0xC>; + assigned-clocks = <&cpts_refclk_mux>; + assigned-clock-parents = <&chipclk12>; + }; + }; + interfaces { gbe0: interface-0 { slave-port = <0>; @@ -219,3 +253,13 @@ netcp: netcp@2000000 { }; }; }; + +CPTS board configuration - select external CPTS RFTCLK: + +&tsrefclk{ + clock-frequency = <500000000>; +}; + +&cpts_refclk_mux { + assigned-clock-parents = <&tsrefclk>; +}; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 9c5e94482b5f..63c73fafe26d 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -15,8 +15,11 @@ Required properties: Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs. Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. Use "cdns,zynqmp-gem" for Zynq Ultrascale+ MPSoC. + Use "sifive,fu540-macb" for SiFive FU540-C000 SoC. Or the generic form: "cdns,emac". - reg: Address and length of the register set for the device + For "sifive,fu540-macb", second range is required to specify the + address and length of the registers for GEMGXL Management block. - interrupts: Should contain macb interrupt - phy-mode: See ethernet.txt file in the same directory. - clock-names: Tuple listing input clock names. diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt index 17d6819669c8..612a8e8abc88 100644 --- a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -6,11 +6,17 @@ present in Documentation/devicetree/bindings/net/stmmac.txt. The device node has additional properties: Required properties: - - compatible : Should contain "altr,socfpga-stmmac" along with - "snps,dwmac" and any applicable more detailed + - compatible : For Cyclone5/Arria5 SoCs it should contain + "altr,socfpga-stmmac". For Arria10/Agilex/Stratix10 SoCs + "altr,socfpga-stmmac-a10-s10". + Along with "snps,dwmac" and any applicable more detailed designware version numbers documented in stmmac.txt - altr,sysmgr-syscon : Should be the phandle to the system manager node that encompasses the glue register, the register offset, and the register shift. + On Cyclone5/Arria5, the register shift represents the PHY mode bits, while + on the Arria10/Stratix10/Agilex platforms, the register shift represents + bit for each emac to enable/disable signals from the FPGA fabric to the + EMAC modules. - altr,f2h_ptp_ref_clk use f2h_ptp_ref_clk instead of default eosc1 clock for ptp ref clk. This affects all emacs as the clock is common. diff --git a/Documentation/devicetree/bindings/net/wiznet,w5x00.txt b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt new file mode 100644 index 000000000000..e9665798c4be --- /dev/null +++ b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt @@ -0,0 +1,50 @@ +* Wiznet w5x00 + +This is a standalone 10/100 MBit Ethernet controller with SPI interface. + +For each device connected to a SPI bus, define a child node within +the SPI master node. + +Required properties: +- compatible: Should be one of the following strings: + "wiznet,w5100" + "wiznet,w5200" + "wiznet,w5500" +- reg: Specify the SPI chip select the chip is wired to. +- interrupts: Specify the interrupt index within the interrupt controller (referred + to above in interrupt-parent) and interrupt type. w5x00 natively + generates falling edge interrupts, however, additional board logic + might invert the signal. +- pinctrl-names: List of assigned state names, see pinctrl binding documentation. +- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line, + see also generic and your platform specific pinctrl binding + documentation. + +Optional properties: +- spi-max-frequency: Maximum frequency of the SPI bus when accessing the w5500. + According to the w5500 datasheet, the chip allows a maximum of 80 MHz, however, + board designs may need to limit this value. +- local-mac-address: See ethernet.txt in the same directory. + + +Example (for Raspberry Pi with pin control stuff for GPIO irq): + +&spi { + ethernet@0: w5500@0 { + compatible = "wiznet,w5500"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <ð1_pins>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + spi-max-frequency = <30000000>; + }; +}; + +&gpio { + eth1_pins: eth1_pins { + brcm,pins = <25>; + brcm,function = <0>; /* in */ + brcm,pull = <0>; /* none */ + }; +}; diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt index 38f9ec076743..7360617cdedb 100644 --- a/Documentation/devicetree/bindings/net/xilinx_axienet.txt +++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt @@ -17,8 +17,15 @@ For more details about mdio please refer phy.txt file in the same directory. Required properties: - compatible : Must be one of "xlnx,axi-ethernet-1.00.a", "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a" -- reg : Address and length of the IO space. -- interrupts : Should be a list of two interrupt, TX and RX. +- reg : Address and length of the IO space, as well as the address + and length of the AXI DMA controller IO space, unless + axistream-connected is specified, in which case the reg + attribute of the node referenced by it is used. +- interrupts : Should be a list of 2 or 3 interrupts: TX DMA, RX DMA, + and optionally Ethernet core. If axistream-connected is + specified, the TX/RX DMA interrupts should be on that node + instead, and only the Ethernet core interrupt is optionally + specified here. - phy-handle : Should point to the external phy device. See ethernet.txt file in the same directory. - xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware @@ -31,15 +38,29 @@ Optional properties: 1 to enable partial TX checksum offload, 2 to enable full TX checksum offload - xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload +- clocks : AXI bus clock for the device. Refer to common clock bindings. + Used to calculate MDIO clock divisor. If not specified, it is + auto-detected from the CPU clock (but only on platforms where + this is possible). New device trees should specify this - the + auto detection is only for backward compatibility. +- axistream-connected: Reference to another node which contains the resources + for the AXI DMA controller used by this device. + If this is specified, the DMA-related resources from that + device (DMA registers and DMA TX/RX interrupts) rather + than this one will be used. + - mdio : Child node for MDIO bus. Must be defined if PHY access is + required through the core's MDIO interface (i.e. always, + unless the PHY is accessed through a different bus). Example: axi_ethernet_eth: ethernet@40c00000 { compatible = "xlnx,axi-ethernet-1.00.a"; device_type = "network"; interrupt-parent = <µblaze_0_axi_intc>; - interrupts = <2 0>; + interrupts = <2 0 1>; + clocks = <&axi_clk>; phy-mode = "mii"; - reg = <0x40c00000 0x40000>; + reg = <0x40c00000 0x40000 0x50c00000 0x40000>; xlnx,rxcsum = <0x2>; xlnx,rxmem = <0x800>; xlnx,txcsum = <0x2>; |