diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt | 18 |
1 files changed, 11 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt index 2e57a33e9029..6a23ad9ac53a 100644 --- a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -4,14 +4,18 @@ Required Properties: - compatible: Should be one of: - "ti,abb-v1" for older SoCs like OMAP3 - "ti,abb-v2" for newer SoCs like OMAP4, OMAP5 + - "ti,abb-v3" for a generic definition where setup and control registers are + provided (example: DRA7) - reg: Address and length of the register set for the device. It contains the information of registers in the same order as described by reg-names - reg-names: Should contain the reg names - - "base-address" - contains base address of ABB module + - "base-address" - contains base address of ABB module (ti,abb-v1,ti,abb-v2) + - "control-address" - contains control register address of ABB module (ti,abb-v3) + - "setup-address" - contains setup register address of ABB module (ti,abb-v3) - "int-address" - contains address of interrupt register for ABB module (also see Optional properties) -- #address-cell: should be 0 -- #size-cell: should be 0 +- #address-cells: should be 0 +- #size-cells: should be 0 - clocks: should point to the clock node used by ABB module - ti,settling-time: Settling time in uSecs from SoC documentation for ABB module to settle down(target time for SR2_WTCNT_VALUE). @@ -41,7 +45,7 @@ Required Properties: Optional Properties: - reg-names: In addition to the required properties, the following are optional - "efuse-address" - Contains efuse base address used to pick up ABB info. - - "ldo-address" - Contains address of ABB LDO overide register address. + - "ldo-address" - Contains address of ABB LDO override register. "efuse-address" is required for this. - ti,ldovbb-vset-mask - Required if ldo-address is set, mask for LDO override register to provide override vset value. @@ -65,7 +69,7 @@ Example #1: Simplest configuration (no efuse data, hard coded ABB table): abb_x: regulator-abb-x { compatible = "ti,abb-v1"; regulator-name = "abb_x"; - #address-cell = <0>; + #address-cells = <0>; #size-cells = <0>; reg = <0x483072f0 0x8>, <0x48306818 0x4>; reg-names = "base-address", "int-address"; @@ -85,7 +89,7 @@ Example #2: Efuse bits contain ABB mode setting (no LDO override capability) abb_y: regulator-abb-y { compatible = "ti,abb-v2"; regulator-name = "abb_y"; - #address-cell = <0>; + #address-cells = <0>; #size-cells = <0>; reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>, <0x4A002268 0x8>; reg-names = "base-address", "int-address", "efuse-address"; @@ -106,7 +110,7 @@ Example #3: Efuse bits contain ABB mode setting and LDO override capability abb_z: regulator-abb-z { compatible = "ti,abb-v2"; regulator-name = "abb_z"; - #address-cell = <0>; + #address-cells = <0>; #size-cells = <0>; reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>, <0x4a002194 0x8>, <0x4ae0C314 0x4>; |