diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound/fsl,ssi.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/sound/fsl,ssi.txt | 87 |
1 files changed, 0 insertions, 87 deletions
diff --git a/Documentation/devicetree/bindings/sound/fsl,ssi.txt b/Documentation/devicetree/bindings/sound/fsl,ssi.txt deleted file mode 100644 index 7e15a85cecd2..000000000000 --- a/Documentation/devicetree/bindings/sound/fsl,ssi.txt +++ /dev/null @@ -1,87 +0,0 @@ -Freescale Synchronous Serial Interface - -The SSI is a serial device that communicates with audio codecs. It can -be programmed in AC97, I2S, left-justified, or right-justified modes. - -Required properties: -- compatible: Compatible list, should contain one of the following - compatibles: - fsl,mpc8610-ssi - fsl,imx51-ssi - fsl,imx35-ssi - fsl,imx21-ssi -- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on. -- reg: Offset and length of the register set for the device. -- interrupts: <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and - level information for the interrupt. This should be - encoded based on the information in section 2) - depending on the type of interrupt controller you - have. -- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. - This number is the maximum allowed value for SFCSR[TFWM0]. - - clocks: "ipg" - Required clock for the SSI unit - "baud" - Required clock for SSI master mode. Otherwise this - clock is not used - -Required are also ac97 link bindings if ac97 is used. See -Documentation/devicetree/bindings/sound/soc-ac97link.txt for the necessary -bindings. - -Optional properties: -- codec-handle: Phandle to a 'codec' node that defines an audio - codec connected to this SSI. This node is typically - a child of an I2C or other control node. -- fsl,fiq-stream-filter: Bool property. Disabled DMA and use FIQ instead to - filter the codec stream. This is necessary for some boards - where an incompatible codec is connected to this SSI, e.g. - on pca100 and pcm043. -- dmas: Generic dma devicetree binding as described in - Documentation/devicetree/bindings/dma/dma.txt. -- dma-names: Two dmas have to be defined, "tx" and "rx", if fsl,imx-fiq - is not defined. -- fsl,mode: The operating mode for the AC97 interface only. - "ac97-slave" - AC97 mode, SSI is clock slave - "ac97-master" - AC97 mode, SSI is clock master -- fsl,ssi-asynchronous: - If specified, the SSI is to be programmed in asynchronous - mode. In this mode, pins SRCK, STCK, SRFS, and STFS must - all be connected to valid signals. In synchronous mode, - SRCK and SRFS are ignored. Asynchronous mode allows - playback and capture to use different sample sizes and - sample rates. Some drivers may require that SRCK and STCK - be connected together, and SRFS and STFS be connected - together. This would still allow different sample sizes, - but not different sample rates. -- fsl,playback-dma: Phandle to a node for the DMA channel to use for - playback of audio. This is typically dictated by SOC - design. See the notes below. - Only used on Power Architecture. -- fsl,capture-dma: Phandle to a node for the DMA channel to use for - capture (recording) of audio. This is typically dictated - by SOC design. See the notes below. - Only used on Power Architecture. - -Child 'codec' node required properties: -- compatible: Compatible list, contains the name of the codec - -Child 'codec' node optional properties: -- clock-frequency: The frequency of the input clock, which typically comes - from an on-board dedicated oscillator. - -Notes on fsl,playback-dma and fsl,capture-dma: - -On SOCs that have an SSI, specific DMA channels are hard-wired for playback -and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for -playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for -playback and DMA channel 3 for capture. The developer can choose which -DMA controller to use, but the channels themselves are hard-wired. The -purpose of these two properties is to represent this hardware design. - -The device tree nodes for the DMA channels that are referenced by -"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with -"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g. -"fsl,mpc8610-dma-channel") can remain. If these nodes are left as -"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA -drivers (fsldma) will attempt to use them, and it will conflict with the -sound drivers. |