diff options
Diffstat (limited to 'Documentation/firmware-guide/acpi/apei/einj.rst')
| -rw-r--r-- | Documentation/firmware-guide/acpi/apei/einj.rst | 67 |
1 files changed, 67 insertions, 0 deletions
diff --git a/Documentation/firmware-guide/acpi/apei/einj.rst b/Documentation/firmware-guide/acpi/apei/einj.rst index d6b61d22f525..7d8435d35a18 100644 --- a/Documentation/firmware-guide/acpi/apei/einj.rst +++ b/Documentation/firmware-guide/acpi/apei/einj.rst @@ -32,6 +32,10 @@ configuration:: CONFIG_ACPI_APEI CONFIG_ACPI_APEI_EINJ +...and to (optionally) enable CXL protocol error injection set:: + + CONFIG_ACPI_APEI_EINJ_CXL + The EINJ user interface is in <debugfs mount point>/apei/einj. The following files belong to it: @@ -55,6 +59,9 @@ The following files belong to it: 0x00000200 Platform Correctable 0x00000400 Platform Uncorrectable non-fatal 0x00000800 Platform Uncorrectable fatal + V2_0x00000001 EINJV2 Processor Error + V2_0x00000002 EINJV2 Memory Error + V2_0x00000004 EINJV2 PCI Express Error ================ =================================== The format of the file contents are as above, except present are only @@ -84,6 +91,8 @@ The following files belong to it: Memory address and mask valid (param1 and param2). Bit 2 PCIe (seg,bus,dev,fn) valid (see param4 below). + Bit 3 + EINJv2 extension structure is valid If set to zero, legacy behavior is mimicked where the type of injection specifies just one bit set, and param1 is multiplexed. @@ -118,6 +127,31 @@ The following files belong to it: this actually works depends on what operations the BIOS actually includes in the trigger phase. +- component_id0 .. component_idN, component_syndrome0 .. component_syndromeN + + These files are used to set the "Component Array" field + of the EINJv2 Extension Structure. Each holds a 128-bit + hex value. Writing just a newline to any of these files + sets an invalid (all-ones) value. + +CXL error types are supported from ACPI 6.5 onwards (given a CXL port +is present). The EINJ user interface for CXL error types is at +<debugfs mount point>/cxl. The following files belong to it: + +- einj_types: + + Provides the same functionality as available_error_types above, but + for CXL error types + +- $dport_dev/einj_inject: + + Injects a CXL error type into the CXL port represented by $dport_dev, + where $dport_dev is the name of the CXL port (usually a PCIe device name). + Error injections targeting a CXL 2.0+ port can use the legacy interface + under <debugfs mount point>/apei/einj, while CXL 1.1/1.0 port injections + must use this file. + + BIOS versions based on the ACPI 4.0 specification have limited options in controlling where the errors are injected. Your BIOS may support an extension (enabled with the param_extension=1 module parameter, or boot @@ -172,6 +206,27 @@ An error injection example:: # echo 0x8 > error_type # Choose correctable memory error # echo 1 > error_inject # Inject now +An EINJv2 error injection example:: + + # cd /sys/kernel/debug/apei/einj + # cat available_error_type # See which errors can be injected + 0x00000002 Processor Uncorrectable non-fatal + 0x00000008 Memory Correctable + 0x00000010 Memory Uncorrectable non-fatal + V2_0x00000001 EINJV2 Processor Error + V2_0x00000002 EINJV2 Memory Error + + # echo 0x12345000 > param1 # Set memory address for injection + # echo 0xfffffffffffff000 > param2 # Range - anywhere in this page + # echo 0x1 > component_id0 # First device ID + # echo 0x4 > component_syndrome0 # First error syndrome + # echo 0x2 > component_id1 # Second device ID + # echo 0x4 > component_syndrome1 # Second error syndrome + # echo '' > component_id2 # Mark id2 invalid to terminate list + # echo V2_0x2 > error_type # Choose EINJv2 memory error + # echo 0xa > flags # set flags to indicate EINJv2 + # echo 1 > error_inject # Inject now + You should see something like this in dmesg:: [22715.830801] EDAC sbridge MC3: HANDLING MCE MEMORY ERROR @@ -181,6 +236,18 @@ You should see something like this in dmesg:: [22715.834759] EDAC sbridge MC3: PROCESSOR 0:306e7 TIME 1422553404 SOCKET 0 APIC 0 [22716.616173] EDAC MC3: 1 CE memory read error on CPU_SrcID#0_Channel#0_DIMM#0 (channel:0 slot:0 page:0x12345 offset:0x0 grain:32 syndrome:0x0 - area:DRAM err_code:0001:0090 socket:0 channel_mask:1 rank:0) +A CXL error injection example with $dport_dev=0000:e0:01.1:: + + # cd /sys/kernel/debug/cxl/ + # ls + 0000:e0:01.1 0000:0c:00.0 + # cat einj_types # See which errors can be injected + 0x00008000 CXL.mem Protocol Correctable + 0x00010000 CXL.mem Protocol Uncorrectable non-fatal + 0x00020000 CXL.mem Protocol Uncorrectable fatal + # cd 0000:e0:01.1 # Navigate to dport to inject into + # echo 0x8000 > einj_inject # Inject error + Special notes for injection into SGX enclaves: There may be a separate BIOS setup option to enable SGX injection. |