diff options
Diffstat (limited to 'Documentation/networking/device_drivers')
17 files changed, 565 insertions, 464 deletions
diff --git a/Documentation/networking/device_drivers/cable/index.rst b/Documentation/networking/device_drivers/cable/index.rst deleted file mode 100644 index cce3c4392972..000000000000 --- a/Documentation/networking/device_drivers/cable/index.rst +++ /dev/null @@ -1,18 +0,0 @@ -.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) - -Cable Modem Device Drivers -========================== - -Contents: - -.. toctree:: - :maxdepth: 2 - - sb1000 - -.. only:: subproject and html - - Indices - ======= - - * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/cable/sb1000.rst b/Documentation/networking/device_drivers/cable/sb1000.rst deleted file mode 100644 index c8582ca4034d..000000000000 --- a/Documentation/networking/device_drivers/cable/sb1000.rst +++ /dev/null @@ -1,222 +0,0 @@ -.. SPDX-License-Identifier: GPL-2.0 - -=================== -SB100 device driver -=================== - -sb1000 is a module network device driver for the General Instrument (also known -as NextLevel) SURFboard1000 internal cable modem board. This is an ISA card -which is used by a number of cable TV companies to provide cable modem access. -It's a one-way downstream-only cable modem, meaning that your upstream net link -is provided by your regular phone modem. - -This driver was written by Franco Venturi <fventuri@mediaone.net>. He deserves -a great deal of thanks for this wonderful piece of code! - -Needed tools -============ - -Support for this device is now a part of the standard Linux kernel. The -driver source code file is drivers/net/sb1000.c. In addition to this -you will need: - -1. The "cmconfig" program. This is a utility which supplements "ifconfig" - to configure the cable modem and network interface (usually called "cm0"); - -2. Several PPP scripts which live in /etc/ppp to make connecting via your - cable modem easy. - - These utilities can be obtained from: - - http://www.jacksonville.net/~fventuri/ - - in Franco's original source code distribution .tar.gz file. Support for - the sb1000 driver can be found at: - - - http://web.archive.org/web/%2E/http://home.adelphia.net/~siglercm/sb1000.html - - http://web.archive.org/web/%2E/http://linuxpower.cx/~cable/ - - along with these utilities. - -3. The standard isapnp tools. These are necessary to configure your SB1000 - card at boot time (or afterwards by hand) since it's a PnP card. - - If you don't have these installed as a standard part of your Linux - distribution, you can find them at: - - http://www.roestock.demon.co.uk/isapnptools/ - - or check your Linux distribution binary CD or their web site. For help with - isapnp, pnpdump, or /etc/isapnp.conf, go to: - - http://www.roestock.demon.co.uk/isapnptools/isapnpfaq.html - -Using the driver -================ - -To make the SB1000 card work, follow these steps: - -1. Run ``make config``, or ``make menuconfig``, or ``make xconfig``, whichever - you prefer, in the top kernel tree directory to set up your kernel - configuration. Make sure to say "Y" to "Prompt for development drivers" - and to say "M" to the sb1000 driver. Also say "Y" or "M" to all the standard - networking questions to get TCP/IP and PPP networking support. - -2. **BEFORE** you build the kernel, edit drivers/net/sb1000.c. Make sure - to redefine the value of READ_DATA_PORT to match the I/O address used - by isapnp to access your PnP cards. This is the value of READPORT in - /etc/isapnp.conf or given by the output of pnpdump. - -3. Build and install the kernel and modules as usual. - -4. Boot your new kernel following the usual procedures. - -5. Set up to configure the new SB1000 PnP card by capturing the output - of "pnpdump" to a file and editing this file to set the correct I/O ports, - IRQ, and DMA settings for all your PnP cards. Make sure none of the settings - conflict with one another. Then test this configuration by running the - "isapnp" command with your new config file as the input. Check for - errors and fix as necessary. (As an aside, I use I/O ports 0x110 and - 0x310 and IRQ 11 for my SB1000 card and these work well for me. YMMV.) - Then save the finished config file as /etc/isapnp.conf for proper - configuration on subsequent reboots. - -6. Download the original file sb1000-1.1.2.tar.gz from Franco's site or one of - the others referenced above. As root, unpack it into a temporary directory - and do a ``make cmconfig`` and then ``install -c cmconfig /usr/local/sbin``. - Don't do ``make install`` because it expects to find all the utilities built - and ready for installation, not just cmconfig. - -7. As root, copy all the files under the ppp/ subdirectory in Franco's - tar file into /etc/ppp, being careful not to overwrite any files that are - already in there. Then modify ppp@gi-on to set the correct login name, - phone number, and frequency for the cable modem. Also edit pap-secrets - to specify your login name and password and any site-specific information - you need. - -8. Be sure to modify /etc/ppp/firewall to use ipchains instead of - the older ipfwadm commands from the 2.0.x kernels. There's a neat utility to - convert ipfwadm commands to ipchains commands: - - http://users.dhp.com/~whisper/ipfwadm2ipchains/ - - You may also wish to modify the firewall script to implement a different - firewalling scheme. - -9. Start the PPP connection via the script /etc/ppp/ppp@gi-on. You must be - root to do this. It's better to use a utility like sudo to execute - frequently used commands like this with root permissions if possible. If you - connect successfully the cable modem interface will come up and you'll see a - driver message like this at the console:: - - cm0: sb1000 at (0x110,0x310), csn 1, S/N 0x2a0d16d8, IRQ 11. - sb1000.c:v1.1.2 6/01/98 (fventuri@mediaone.net) - - The "ifconfig" command should show two new interfaces, ppp0 and cm0. - - The command "cmconfig cm0" will give you information about the cable modem - interface. - -10. Try pinging a site via ``ping -c 5 www.yahoo.com``, for example. You should - see packets received. - -11. If you can't get site names (like www.yahoo.com) to resolve into - IP addresses (like 204.71.200.67), be sure your /etc/resolv.conf file - has no syntax errors and has the right nameserver IP addresses in it. - If this doesn't help, try something like ``ping -c 5 204.71.200.67`` to - see if the networking is running but the DNS resolution is where the - problem lies. - -12. If you still have problems, go to the support web sites mentioned above - and read the information and documentation there. - -Common problems -=============== - -1. Packets go out on the ppp0 interface but don't come back on the cm0 - interface. It looks like I'm connected but I can't even ping any - numerical IP addresses. (This happens predominantly on Debian systems due - to a default boot-time configuration script.) - -Solution - As root ``echo 0 > /proc/sys/net/ipv4/conf/cm0/rp_filter`` so it - can share the same IP address as the ppp0 interface. Note that this - command should probably be added to the /etc/ppp/cablemodem script - *right*between* the "/sbin/ifconfig" and "/sbin/cmconfig" commands. - You may need to do this to /proc/sys/net/ipv4/conf/ppp0/rp_filter as well. - If you do this to /proc/sys/net/ipv4/conf/default/rp_filter on each reboot - (in rc.local or some such) then any interfaces can share the same IP - addresses. - -2. I get "unresolved symbol" error messages on executing ``insmod sb1000.o``. - -Solution - You probably have a non-matching kernel source tree and - /usr/include/linux and /usr/include/asm header files. Make sure you - install the correct versions of the header files in these two directories. - Then rebuild and reinstall the kernel. - -3. When isapnp runs it reports an error, and my SB1000 card isn't working. - -Solution - There's a problem with later versions of isapnp using the "(CHECK)" - option in the lines that allocate the two I/O addresses for the SB1000 card. - This first popped up on RH 6.0. Delete "(CHECK)" for the SB1000 I/O addresses. - Make sure they don't conflict with any other pieces of hardware first! Then - rerun isapnp and go from there. - -4. I can't execute the /etc/ppp/ppp@gi-on file. - -Solution - As root do ``chmod ug+x /etc/ppp/ppp@gi-on``. - -5. The firewall script isn't working (with 2.2.x and higher kernels). - -Solution - Use the ipfwadm2ipchains script referenced above to convert the - /etc/ppp/firewall script from the deprecated ipfwadm commands to ipchains. - -6. I'm getting *tons* of firewall deny messages in the /var/kern.log, - /var/messages, and/or /var/syslog files, and they're filling up my /var - partition!!! - -Solution - First, tell your ISP that you're receiving DoS (Denial of Service) - and/or portscanning (UDP connection attempts) attacks! Look over the deny - messages to figure out what the attack is and where it's coming from. Next, - edit /etc/ppp/cablemodem and make sure the ",nobroadcast" option is turned on - to the "cmconfig" command (uncomment that line). If you're not receiving these - denied packets on your broadcast interface (IP address xxx.yyy.zzz.255 - typically), then someone is attacking your machine in particular. Be careful - out there.... - -7. Everything seems to work fine but my computer locks up after a while - (and typically during a lengthy download through the cable modem)! - -Solution - You may need to add a short delay in the driver to 'slow down' the - SURFboard because your PC might not be able to keep up with the transfer rate - of the SB1000. To do this, it's probably best to download Franco's - sb1000-1.1.2.tar.gz archive and build and install sb1000.o manually. You'll - want to edit the 'Makefile' and look for the 'SB1000_DELAY' - define. Uncomment those 'CFLAGS' lines (and comment out the default ones) - and try setting the delay to something like 60 microseconds with: - '-DSB1000_DELAY=60'. Then do ``make`` and as root ``make install`` and try - it out. If it still doesn't work or you like playing with the driver, you may - try other numbers. Remember though that the higher the delay, the slower the - driver (which slows down the rest of the PC too when it is actively - used). Thanks to Ed Daiga for this tip! - -Credits -======= - -This README came from Franco Venturi's original README file which is -still supplied with his driver .tar.gz archive. I and all other sb1000 users -owe Franco a tremendous "Thank you!" Additional thanks goes to Carl Patten -and Ralph Bonnell who are now managing the Linux SB1000 web site, and to -the SB1000 users who reported and helped debug the common problems listed -above. - - - Clemmitt Sigler - csigler@vt.edu diff --git a/Documentation/networking/device_drivers/ethernet/amazon/ena.rst b/Documentation/networking/device_drivers/ethernet/amazon/ena.rst index a4c7d0c65fd7..4561e8ab9e08 100644 --- a/Documentation/networking/device_drivers/ethernet/amazon/ena.rst +++ b/Documentation/networking/device_drivers/ethernet/amazon/ena.rst @@ -230,6 +230,11 @@ per-queue stats) from the device. In addition the driver logs the stats to syslog upon device reset. +On supported instance types, the statistics will also include the +ENA Express data (fields prefixed with `ena_srd`). For a complete +documentation of ENA Express data refer to +https://docs.aws.amazon.com/AWSEC2/latest/UserGuide/ena-express.html#ena-express-monitor + MTU === diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst index 199647729251..32ee827a3a2c 100644 --- a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst +++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst @@ -339,7 +339,7 @@ Key functions include: a bind of the root DPRC to the DPRC driver The binding for the MC-bus device-tree node can be consulted at -*Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt*. +*Documentation/devicetree/bindings/misc/fsl,qoriq-mc.yaml*. The sysfs bind/unbind interfaces for the MC-bus can be consulted at *Documentation/ABI/testing/sysfs-bus-fsl-mc*. diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/switch-driver.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/switch-driver.rst index 8bf411b857d4..5f3885e56f58 100644 --- a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/switch-driver.rst +++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/switch-driver.rst @@ -70,7 +70,7 @@ the DPSW object that it will probe: Besides the configuration of the actual DPSW object, the dpaa2-switch driver will need the following DPAA2 objects: - * 1 DPMCP - A Management Command Portal object is needed for any interraction + * 1 DPMCP - A Management Command Portal object is needed for any interaction with the MC firmware. * 1 DPBP - A Buffer Pool is used for seeding buffers intended for the Rx path diff --git a/Documentation/networking/device_drivers/ethernet/huawei/hinic3.rst b/Documentation/networking/device_drivers/ethernet/huawei/hinic3.rst new file mode 100644 index 000000000000..e3dfd083fa52 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/huawei/hinic3.rst @@ -0,0 +1,137 @@ +.. SPDX-License-Identifier: GPL-2.0 + +===================================================================== +Linux kernel driver for Huawei Ethernet Device Driver (hinic3) family +===================================================================== + +Overview +======== + +The hinic3 is a network interface card (NIC) for Data Center. It supports +a range of link-speed devices (10GE, 25GE, 100GE, etc.). The hinic3 +devices can have multiple physical forms: LOM (Lan on Motherboard) NIC, +PCIe standard NIC, OCP (Open Compute Project) NIC, etc. + +The hinic3 driver supports the following features: +- IPv4/IPv6 TCP/UDP checksum offload +- TSO (TCP Segmentation Offload), LRO (Large Receive Offload) +- RSS (Receive Side Scaling) +- MSI-X interrupt aggregation configuration and interrupt adaptation. +- SR-IOV (Single Root I/O Virtualization). + +Content +======= + +- Supported PCI vendor ID/device IDs +- Source Code Structure of Hinic3 Driver +- Management Interface + +Supported PCI vendor ID/device IDs +================================== + +19e5:0222 - hinic3 PF/PPF +19e5:375F - hinic3 VF + +Prime Physical Function (PPF) is responsible for the management of the +whole NIC card. For example, clock synchronization between the NIC and +the host. Any PF may serve as a PPF. The PPF is selected dynamically. + +Source Code Structure of Hinic3 Driver +====================================== + +======================== ================================================ +hinic3_pci_id_tbl.h Supported device IDs +hinic3_hw_intf.h Interface between HW and driver +hinic3_queue_common.[ch] Common structures and methods for NIC queues +hinic3_common.[ch] Encapsulation of memory operations in Linux +hinic3_csr.h Register definitions in the BAR +hinic3_hwif.[ch] Interface for BAR +hinic3_eqs.[ch] Interface for AEQs and CEQs +hinic3_mbox.[ch] Interface for mailbox +hinic3_mgmt.[ch] Management interface based on mailbox and AEQ +hinic3_wq.[ch] Work queue data structures and interface +hinic3_cmdq.[ch] Command queue is used to post command to HW +hinic3_hwdev.[ch] HW structures and methods abstractions +hinic3_lld.[ch] Auxiliary driver adaptation layer +hinic3_hw_comm.[ch] Interface for common HW operations +hinic3_mgmt_interface.h Interface between firmware and driver +hinic3_hw_cfg.[ch] Interface for HW configuration +hinic3_irq.c Interrupt request +hinic3_netdev_ops.c Operations registered to Linux kernel stack +hinic3_nic_dev.h NIC structures and methods abstractions +hinic3_main.c Main Linux kernel driver +hinic3_nic_cfg.[ch] NIC service configuration +hinic3_nic_io.[ch] Management plane interface for TX and RX +hinic3_rss.[ch] Interface for Receive Side Scaling (RSS) +hinic3_rx.[ch] Interface for transmit +hinic3_tx.[ch] Interface for receive +hinic3_ethtool.c Interface for ethtool operations (ops) +hinic3_filter.c Interface for MAC address +======================== ================================================ + +Management Interface +==================== + +Asynchronous Event Queue (AEQ) +------------------------------ + +AEQ receives high priority events from the HW over a descriptor queue. +Every descriptor is a fixed size of 64 bytes. AEQ can receive solicited or +unsolicited events. Every device, VF or PF, can have up to 4 AEQs. +Every AEQ is associated to a dedicated IRQ. AEQ can receive multiple types +of events, but in practice the hinic3 driver ignores all events except for +2 mailbox related events. + +Mailbox +------- + +Mailbox is a communication mechanism between the hinic3 driver and the HW. +Each device has an independent mailbox. Driver can use the mailbox to send +requests to management. Driver receives mailbox messages, such as responses +to requests, over the AEQ (using event HINIC3_AEQ_FOR_MBOX). Due to the +limited size of mailbox data register, mailbox messages are sent +segment-by-segment. + +Every device can use its mailbox to post request to firmware. The mailbox +can also be used to post requests and responses between the PF and its VFs. + +Completion Event Queue (CEQ) +---------------------------- + +The implementation of CEQ is the same as AEQ. It receives completion events +from HW over a fixed size descriptor of 32 bits. Every device can have up +to 32 CEQs. Every CEQ has a dedicated IRQ. CEQ only receives solicited +events that are responses to requests from the driver. CEQ can receive +multiple types of events, but in practice the hinic3 driver ignores all +events except for HINIC3_CMDQ that represents completion of previously +posted commands on a cmdq. + +Command Queue (cmdq) +-------------------- + +Every cmdq has a dedicated work queue on which commands are posted. +Commands on the work queue are fixed size descriptor of size 64 bytes. +Completion of a command will be indicated using ctrl bits in the +descriptor that carried the command. Notification of command completions +will also be provided via event on CEQ. Every device has 4 command queues +that are initialized as a set (called cmdqs), each with its own type. +Hinic3 driver only uses type HINIC3_CMDQ_SYNC. + +Work Queues(WQ) +--------------- + +Work queues are logical arrays of fixed size WQEs. The array may be spread +over multiple non-contiguous pages using indirection table. Work queues are +used by I/O queues and command queues. + +Global function ID +------------------ + +Every function, PF or VF, has a unique ordinal identification within the device. +Many management commands (mbox or cmdq) contain this ID so HW can apply the +command effect to the right function. + +PF is allowed to post management commands to a subordinate VF by specifying the +VFs ID. A VF must provide its own ID. Anti-spoofing in the HW will cause +command from a VF to fail if it contains the wrong ID. + diff --git a/Documentation/networking/device_drivers/ethernet/index.rst b/Documentation/networking/device_drivers/ethernet/index.rst index 6932d8c043c2..139b4c75a191 100644 --- a/Documentation/networking/device_drivers/ethernet/index.rst +++ b/Documentation/networking/device_drivers/ethernet/index.rst @@ -28,6 +28,7 @@ Contents: freescale/gianfar google/gve huawei/hinic + huawei/hinic3 intel/e100 intel/e1000 intel/e1000e @@ -44,6 +45,7 @@ Contents: marvell/octeon_ep marvell/octeon_ep_vf mellanox/mlx5/index + meta/fbnic microsoft/netvsc neterion/s2io netronome/nfp @@ -54,7 +56,7 @@ Contents: ti/cpsw_switchdev ti/am65_nuss_cpsw_switchdev ti/tlan - toshiba/spider_net + ti/icssg_prueth wangxun/txgbe wangxun/ngbe diff --git a/Documentation/networking/device_drivers/ethernet/intel/i40e.rst b/Documentation/networking/device_drivers/ethernet/intel/i40e.rst index 4fbaa1a2d674..53d9d5829d69 100644 --- a/Documentation/networking/device_drivers/ethernet/intel/i40e.rst +++ b/Documentation/networking/device_drivers/ethernet/intel/i40e.rst @@ -299,6 +299,18 @@ Use ethtool to view and set link-down-on-close, as follows:: ethtool --show-priv-flags ethX ethtool --set-priv-flags ethX link-down-on-close [on|off] +Setting the mdd-auto-reset-vf Private Flag +------------------------------------------ + +When the mdd-auto-reset-vf private flag is set to "on", the problematic VF will +be automatically reset if a malformed descriptor is detected. If the flag is +set to "off", the problematic VF will be disabled. + +Use ethtool to view and set mdd-auto-reset-vf, as follows:: + + ethtool --show-priv-flags ethX + ethtool --set-priv-flags ethX mdd-auto-reset-vf [on|off] + Viewing Link Messages --------------------- Link messages will not be displayed to the console if the distribution is diff --git a/Documentation/networking/device_drivers/ethernet/intel/ice.rst b/Documentation/networking/device_drivers/ethernet/intel/ice.rst index 934752f675ba..3c46a48d99ba 100644 --- a/Documentation/networking/device_drivers/ethernet/intel/ice.rst +++ b/Documentation/networking/device_drivers/ethernet/intel/ice.rst @@ -101,6 +101,37 @@ example, if Rx packets are 10 and Netdev (software statistics) displays rx_bytes as "X", then ethtool (hardware statistics) will display rx_bytes as "X+40" (4 bytes CRC x 10 packets). +ethtool reset +------------- +The driver supports 3 types of resets: + +- PF reset - resets only components associated with the given PF, does not + impact other PFs + +- CORE reset - whole adapter is affected, reset all PFs + +- GLOBAL reset - same as CORE but mac and phy components are also reinitialized + +These are mapped to ethtool reset flags as follow: + +- PF reset: + + # ethtool --reset <ethX> irq dma filter offload + +- CORE reset: + + # ethtool --reset <ethX> irq-shared dma-shared filter-shared offload-shared \ + ram-shared + +- GLOBAL reset: + + # ethtool --reset <ethX> irq-shared dma-shared filter-shared offload-shared \ + mac-shared phy-shared ram-shared + +In switchdev mode you can reset a VF using port representor: + + # ethtool --reset <repr> irq dma filter offload + Viewing Link Messages --------------------- diff --git a/Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rst b/Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rst index 1e196cb9ce25..a52850602cd8 100644 --- a/Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rst +++ b/Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rst @@ -14,6 +14,7 @@ Contents - `Basic packet flow`_ - `Devlink health reporters`_ - `Quality of service`_ +- `RVU representors`_ Overview ======== @@ -65,7 +66,7 @@ Admin Function driver As mentioned above RVU PF0 is called the admin function (AF), this driver supports resource provisioning and configuration of functional blocks. Doesn't handle any I/O. It sets up few basic stuff but most of the -funcionality is achieved via configuration requests from PFs and VFs. +functionality is achieved via configuration requests from PFs and VFs. PF/VFs communicates with AF via a shared memory region (mailbox). Upon receiving requests AF does resource provisioning and other HW configuration. @@ -340,3 +341,93 @@ Setup HTB offload # tc class add dev <interface> parent 1: classid 1:2 htb rate 10Gbit prio 2 quantum 188416 # tc class add dev <interface> parent 1: classid 1:3 htb rate 10Gbit prio 2 quantum 32768 + + +RVU Representors +================ + +RVU representor driver adds support for creation of representor devices for +RVU PFs' VFs in the system. Representor devices are created when user enables +the switchdev mode. +Switchdev mode can be enabled either before or after setting up SRIOV numVFs. +All representor devices share a single NIXLF but each has a dedicated Rx/Tx +queues. RVU PF representor driver registers a separate netdev for each +Rx/Tx queue pair. + +Current HW does not support built-in switch which can do L2 learning and +forwarding packets between representee and representor. Hence, packet path +between representee and it's representor is achieved by setting up appropriate +NPC MCAM filters. +Transmit packets matching these filters will be loopbacked through hardware +loopback channel/interface (i.e, instead of sending them out of MAC interface). +Which will again match the installed filters and will be forwarded. +This way representee => representor and representor => representee packet +path is achieved. These rules get installed when representors are created +and gets active/deactivate based on the representor/representee interface state. + +Usage example: + + - Change device to switchdev mode:: + + # devlink dev eswitch set pci/0002:1c:00.0 mode switchdev + + - List of representor devices on the system:: + + # ip link show + Rpf1vf0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether f6:43:83:ee:26:21 brd ff:ff:ff:ff:ff:ff + Rpf1vf1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether 12:b2:54:0e:24:54 brd ff:ff:ff:ff:ff:ff + Rpf1vf2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether 4a:12:c4:4c:32:62 brd ff:ff:ff:ff:ff:ff + Rpf1vf3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether ca:cb:68:0e:e2:6e brd ff:ff:ff:ff:ff:ff + Rpf2vf0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether 06:cc:ad:b4:f0:93 brd ff:ff:ff:ff:ff:ff + + +To delete the representors devices from the system. Change the device to legacy mode. + + - Change device to legacy mode:: + + # devlink dev eswitch set pci/0002:1c:00.0 mode legacy + +RVU representors can be managed using devlink ports +(see :ref:`Documentation/networking/devlink/devlink-port.rst <devlink_port>`) interface. + + - Show devlink ports of representors:: + + # devlink port + pci/0002:1c:00.0/0: type eth netdev Rpf1vf0 flavour physical port 0 splittable false + pci/0002:1c:00.0/1: type eth netdev Rpf1vf1 flavour pcivf controller 0 pfnum 1 vfnum 1 external false splittable false + pci/0002:1c:00.0/2: type eth netdev Rpf1vf2 flavour pcivf controller 0 pfnum 1 vfnum 2 external false splittable false + pci/0002:1c:00.0/3: type eth netdev Rpf1vf3 flavour pcivf controller 0 pfnum 1 vfnum 3 external false splittable false + +Function attributes +=================== + +The RVU representor support function attributes for representors. +Port function configuration of the representors are supported through devlink eswitch port. + +MAC address setup +----------------- + +RVU representor driver support devlink port function attr mechanism to setup MAC +address. (refer to Documentation/networking/devlink/devlink-port.rst) + + - To setup MAC address for port 2:: + + # devlink port function set pci/0002:1c:00.0/2 hw_addr 5c:a1:1b:5e:43:11 + # devlink port show pci/0002:1c:00.0/2 + pci/0002:1c:00.0/2: type eth netdev Rpf1vf2 flavour pcivf controller 0 pfnum 1 vfnum 2 external false splittable false + function: + hw_addr 5c:a1:1b:5e:43:11 + + +TC offload +========== + +The rvu representor driver implements support for offloading tc rules using port representors. + + - Drop packets with vlan id 3:: + + # tc filter add dev Rpf1vf0 protocol 802.1Q parent ffff: flower vlan_id 3 vlan_ethtype ipv4 skip_sw action drop + + - Redirect packets with vlan id 5 and IPv4 packets to eth1, after stripping vlan header.:: + + # tc filter add dev Rpf1vf0 ingress protocol 802.1Q flower vlan_id 5 vlan_ethtype ipv4 skip_sw action vlan pop action mirred ingress redirect dev eth1 diff --git a/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/counters.rst b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/counters.rst index fed821ef9b09..43d72c8b713b 100644 --- a/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/counters.rst +++ b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/counters.rst @@ -189,22 +189,19 @@ the software port. * - `rx[i]_gro_packets` - Number of received packets processed using hardware-accelerated GRO. The - number of hardware GRO offloaded packets received on ring i. + number of hardware GRO offloaded packets received on ring i. Only true GRO + packets are counted: only packets that are in an SKB with a GRO count > 1. - Acceleration * - `rx[i]_gro_bytes` - Number of received bytes processed using hardware-accelerated GRO. The - number of hardware GRO offloaded bytes received on ring i. + number of hardware GRO offloaded bytes received on ring i. Only true GRO + packets are counted: only packets that are in an SKB with a GRO count > 1. - Acceleration * - `rx[i]_gro_skbs` - - The number of receive SKBs constructed while performing - hardware-accelerated GRO. - - Informative - - * - `rx[i]_gro_match_packets` - - Number of received packets processed using hardware-accelerated GRO that - met the flow table match criteria. + - The number of GRO SKBs constructed from hardware-accelerated GRO. Only SKBs + with a GRO count > 1 are counted. - Informative * - `rx[i]_gro_large_hds` @@ -212,6 +209,31 @@ the software port. headers that require additional memory to be allocated. - Informative + * - `rx[i]_hds_nodata_packets` + - Number of header only packets in header/data split mode [#accel]_. + - Informative + + * - `rx[i]_hds_nodata_bytes` + - Number of bytes for header only packets in header/data split mode + [#accel]_. + - Informative + + * - `rx[i]_hds_nosplit_packets` + - Number of packets that were not split in header/data split mode. A + packet will not get split when the hardware does not support its + protocol splitting. An example such a protocol is ICMPv4/v6. Currently + TCP and UDP with IPv4/IPv6 are supported for header/data split + [#accel]_. + - Informative + + * - `rx[i]_hds_nosplit_bytes` + - Number of bytes for packets that were not split in header/data split + mode. A packet will not get split when the hardware does not support its + protocol splitting. An example such a protocol is ICMPv4/v6. Currently + TCP and UDP with IPv4/IPv6 are supported for header/data split + [#accel]_. + - Informative + * - `rx[i]_lro_packets` - The number of LRO packets received on ring i [#accel]_. - Acceleration @@ -1060,6 +1082,11 @@ like flow control, FEC and more. need to replace the cable/transceiver. - Error + * - `total_success_recovery_phy` + - The number of total successful recovery events of any type during + ports reset cycle. + - Error + * - `rx_out_of_buffer` - Number of times receive queue had no software buffers allocated for the adapter's incoming traffic. diff --git a/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/kconfig.rst b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/kconfig.rst index 20d3b7e87049..34e911480108 100644 --- a/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/kconfig.rst +++ b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/kconfig.rst @@ -130,6 +130,9 @@ Enabling the driver and kconfig options | Build support for software-managed steering in the NIC. +**CONFIG_MLX5_HW_STEERING=(y/n)** + +| Build support for hardware-managed steering in the NIC. **CONFIG_MLX5_TC_CT=(y/n)** diff --git a/Documentation/networking/device_drivers/ethernet/meta/fbnic.rst b/Documentation/networking/device_drivers/ethernet/meta/fbnic.rst new file mode 100644 index 000000000000..f8592dec8851 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/meta/fbnic.rst @@ -0,0 +1,132 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +===================================== +Meta Platforms Host Network Interface +===================================== + +Firmware Versions +----------------- + +fbnic has three components stored on the flash which are provided in one PLDM +image: + +1. fw - The control firmware used to view and modify firmware settings, request + firmware actions, and retrieve firmware counters outside of the data path. + This is the firmware which fbnic_fw.c interacts with. +2. bootloader - The firmware which validate firmware security and control basic + operations including loading and updating the firmware. This is also known + as the cmrt firmware. +3. undi - This is the UEFI driver which is based on the Linux driver. + +fbnic stores two copies of these three components on flash. This allows fbnic +to fall back to an older version of firmware automatically in case firmware +fails to boot. Version information for both is provided as running and stored. +The undi is only provided in stored as it is not actively running once the Linux +driver takes over. + +devlink dev info provides version information for all three components. In +addition to the version the hg commit hash of the build is included as a +separate entry. + +Upgrading Firmware +------------------ + +fbnic supports updating firmware using signed PLDM images with devlink dev +flash. PLDM images are written into the flash. Flashing does not interrupt +the operation of the device. + +On host boot the latest UEFI driver is always used, no explicit activation +is required. Firmware activation is required to run new control firmware. cmrt +firmware can only be activated by power cycling the NIC. + +Statistics +---------- + +TX MAC Interface +~~~~~~~~~~~~~~~~ + + - ``ptp_illegal_req``: packets sent to the NIC with PTP request bit set but routed to BMC/FW + - ``ptp_good_ts``: packets successfully routed to MAC with PTP request bit set + - ``ptp_bad_ts``: packets destined for MAC with PTP request bit set but aborted because of some error (e.g., DMA read error) + +TX Extension (TEI) Interface (TTI) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + + - ``tti_cm_drop``: control messages dropped at the TX Extension (TEI) Interface because of credit starvation + - ``tti_frame_drop``: packets dropped at the TX Extension (TEI) Interface because of credit starvation + - ``tti_tbi_drop``: packets dropped at the TX BMC Interface (TBI) because of credit starvation + +RXB (RX Buffer) Enqueue +~~~~~~~~~~~~~~~~~~~~~~~ + + - ``rxb_integrity_err[i]``: frames enqueued with integrity errors (e.g., multi-bit ECC errors) on RXB input i + - ``rxb_mac_err[i]``: frames enqueued with MAC end-of-frame errors (e.g., bad FCS) on RXB input i + - ``rxb_parser_err[i]``: frames experienced RPC parser errors + - ``rxb_frm_err[i]``: frames experienced signaling errors (e.g., missing end-of-packet/start-of-packet) on RXB input i + - ``rxb_drbo[i]_frames``: frames received at RXB input i + - ``rxb_drbo[i]_bytes``: bytes received at RXB input i + +RXB (RX Buffer) FIFO +~~~~~~~~~~~~~~~~~~~~ + + - ``rxb_fifo[i]_drop``: transitions into the drop state on RXB pool i + - ``rxb_fifo[i]_dropped_frames``: frames dropped on RXB pool i + - ``rxb_fifo[i]_ecn``: transitions into the ECN mark state on RXB pool i + - ``rxb_fifo[i]_level``: current occupancy of RXB pool i + +RXB (RX Buffer) Dequeue +~~~~~~~~~~~~~~~~~~~~~~~ + + - ``rxb_intf[i]_frames``: frames sent to the output i + - ``rxb_intf[i]_bytes``: bytes sent to the output i + - ``rxb_pbuf[i]_frames``: frames sent to output i from the perspective of internal packet buffer + - ``rxb_pbuf[i]_bytes``: bytes sent to output i from the perspective of internal packet buffer + +RPC (Rx parser) +~~~~~~~~~~~~~~~ + + - ``rpc_unkn_etype``: frames containing unknown EtherType + - ``rpc_unkn_ext_hdr``: frames containing unknown IPv6 extension header + - ``rpc_ipv4_frag``: frames containing IPv4 fragment + - ``rpc_ipv6_frag``: frames containing IPv6 fragment + - ``rpc_ipv4_esp``: frames with IPv4 ESP encapsulation + - ``rpc_ipv6_esp``: frames with IPv6 ESP encapsulation + - ``rpc_tcp_opt_err``: frames which encountered TCP option parsing error + - ``rpc_out_of_hdr_err``: frames where header was larger than parsable region + - ``ovr_size_err``: oversized frames + +Hardware Queues +~~~~~~~~~~~~~~~ + +1. RX DMA Engine: + + - ``rde_[i]_pkt_err``: packets with MAC EOP, RPC parser, RXB truncation, or RDE frame truncation errors. These error are flagged in the packet metadata because of cut-through support but the actual drop happens once PCIE/RDE is reached. + - ``rde_[i]_pkt_cq_drop``: packets dropped because RCQ is full + - ``rde_[i]_pkt_bdq_drop``: packets dropped because HPQ or PPQ ran out of host buffer + +PCIe +~~~~ + +The fbnic driver exposes PCIe hardware performance statistics through debugfs +(``pcie_stats``). These statistics provide insights into PCIe transaction +behavior and potential performance bottlenecks. + +1. PCIe Transaction Counters: + + These counters track PCIe transaction activity: + - ``pcie_ob_rd_tlp``: Outbound read Transaction Layer Packets count + - ``pcie_ob_rd_dword``: DWORDs transferred in outbound read transactions + - ``pcie_ob_wr_tlp``: Outbound write Transaction Layer Packets count + - ``pcie_ob_wr_dword``: DWORDs transferred in outbound write + transactions + - ``pcie_ob_cpl_tlp``: Outbound completion TLP count + - ``pcie_ob_cpl_dword``: DWORDs transferred in outbound completion TLPs + +2. PCIe Resource Monitoring: + + These counters indicate PCIe resource exhaustion events: + - ``pcie_ob_rd_no_tag``: Read requests dropped due to tag unavailability + - ``pcie_ob_rd_no_cpl_cred``: Read requests dropped due to completion + credit exhaustion + - ``pcie_ob_rd_no_np_cred``: Read requests dropped due to non-posted + credit exhaustion diff --git a/Documentation/networking/device_drivers/ethernet/ti/icssg_prueth.rst b/Documentation/networking/device_drivers/ethernet/ti/icssg_prueth.rst new file mode 100644 index 000000000000..da21ddf431bb --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/ti/icssg_prueth.rst @@ -0,0 +1,56 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================================== +Texas Instruments ICSSG PRUETH ethernet driver +============================================== + +:Version: 1.0 + +ICSSG Firmware +============== + +Every ICSSG core has two Programmable Real-Time Unit(PRUs), two auxiliary +Real-Time Transfer Unit (RTUs), and two Transmit Real-Time Transfer Units +(TX_PRUs). Each one of these runs its own firmware. The firmwares combnined are +referred as ICSSG Firmware. + +Firmware Statistics +=================== + +The ICSSG firmware maintains certain statistics which are dumped by the driver +via ``ethtool -S <interface>`` + +These statistics are as follows, + + - ``FW_RTU_PKT_DROP``: Diagnostic error counter which increments when RTU drops a locally injected packet due to port being disabled or rule violation. + - ``FW_Q0_OVERFLOW``: TX overflow counter for queue0 + - ``FW_Q1_OVERFLOW``: TX overflow counter for queue1 + - ``FW_Q2_OVERFLOW``: TX overflow counter for queue2 + - ``FW_Q3_OVERFLOW``: TX overflow counter for queue3 + - ``FW_Q4_OVERFLOW``: TX overflow counter for queue4 + - ``FW_Q5_OVERFLOW``: TX overflow counter for queue5 + - ``FW_Q6_OVERFLOW``: TX overflow counter for queue6 + - ``FW_Q7_OVERFLOW``: TX overflow counter for queue7 + - ``FW_DROPPED_PKT``: This counter is incremented when a packet is dropped at PRU because of rule violation. + - ``FW_RX_ERROR``: Incremented if there was a CRC error or Min/Max frame error at PRU + - ``FW_RX_DS_INVALID``: Incremented when RTU detects Data Status invalid condition + - ``FW_TX_DROPPED_PACKET``: Counter for packets dropped via TX Port + - ``FW_TX_TS_DROPPED_PACKET``: Counter for packets with TS flag dropped via TX Port + - ``FW_INF_PORT_DISABLED``: Incremented when RX frame is dropped due to port being disabled + - ``FW_INF_SAV``: Incremented when RX frame is dropped due to Source Address violation + - ``FW_INF_SA_DL``: Incremented when RX frame is dropped due to Source Address being in the denylist + - ``FW_INF_PORT_BLOCKED``: Incremented when RX frame is dropped due to port being blocked and frame being a special frame + - ``FW_INF_DROP_TAGGED`` : Incremented when RX frame is dropped for being tagged + - ``FW_INF_DROP_PRIOTAGGED``: Incremented when RX frame is dropped for being priority tagged + - ``FW_INF_DROP_NOTAG``: Incremented when RX frame is dropped for being untagged + - ``FW_INF_DROP_NOTMEMBER``: Incremented when RX frame is dropped for port not being member of VLAN + - ``FW_RX_EOF_SHORT_FRMERR``: Incremented if End Of Frame (EOF) task is scheduled without seeing RX_B1 + - ``FW_RX_B0_DROP_EARLY_EOF``: Incremented when frame is dropped due to Early EOF + - ``FW_TX_JUMBO_FRM_CUTOFF``: Incremented when frame is cut off to prevent packet size > 2000 Bytes + - ``FW_RX_EXP_FRAG_Q_DROP``: Incremented when express frame is received in the same queue as the previous fragment + - ``FW_RX_FIFO_OVERRUN``: RX fifo overrun counter + - ``FW_CUT_THR_PKT``: Incremented when a packet is forwarded using Cut-Through forwarding method + - ``FW_HOST_RX_PKT_CNT``: Number of valid packets sent by Rx PRU to Host on PSI + - ``FW_HOST_TX_PKT_CNT``: Number of valid packets copied by RTU0 to Tx queues + - ``FW_HOST_EGRESS_Q_PRE_OVERFLOW``: Host Egress Q (Pre-emptible) Overflow Counter + - ``FW_HOST_EGRESS_Q_EXP_OVERFLOW``: Host Egress Q (Pre-emptible) Overflow Counter diff --git a/Documentation/networking/device_drivers/ethernet/toshiba/spider_net.rst b/Documentation/networking/device_drivers/ethernet/toshiba/spider_net.rst deleted file mode 100644 index fe5b32be15cd..000000000000 --- a/Documentation/networking/device_drivers/ethernet/toshiba/spider_net.rst +++ /dev/null @@ -1,202 +0,0 @@ -.. SPDX-License-Identifier: GPL-2.0 - -=========================== -The Spidernet Device Driver -=========================== - -Written by Linas Vepstas <linas@austin.ibm.com> - -Version of 7 June 2007 - -Abstract -======== -This document sketches the structure of portions of the spidernet -device driver in the Linux kernel tree. The spidernet is a gigabit -ethernet device built into the Toshiba southbridge commonly used -in the SONY Playstation 3 and the IBM QS20 Cell blade. - -The Structure of the RX Ring. -============================= -The receive (RX) ring is a circular linked list of RX descriptors, -together with three pointers into the ring that are used to manage its -contents. - -The elements of the ring are called "descriptors" or "descrs"; they -describe the received data. This includes a pointer to a buffer -containing the received data, the buffer size, and various status bits. - -There are three primary states that a descriptor can be in: "empty", -"full" and "not-in-use". An "empty" or "ready" descriptor is ready -to receive data from the hardware. A "full" descriptor has data in it, -and is waiting to be emptied and processed by the OS. A "not-in-use" -descriptor is neither empty or full; it is simply not ready. It may -not even have a data buffer in it, or is otherwise unusable. - -During normal operation, on device startup, the OS (specifically, the -spidernet device driver) allocates a set of RX descriptors and RX -buffers. These are all marked "empty", ready to receive data. This -ring is handed off to the hardware, which sequentially fills in the -buffers, and marks them "full". The OS follows up, taking the full -buffers, processing them, and re-marking them empty. - -This filling and emptying is managed by three pointers, the "head" -and "tail" pointers, managed by the OS, and a hardware current -descriptor pointer (GDACTDPA). The GDACTDPA points at the descr -currently being filled. When this descr is filled, the hardware -marks it full, and advances the GDACTDPA by one. Thus, when there is -flowing RX traffic, every descr behind it should be marked "full", -and everything in front of it should be "empty". If the hardware -discovers that the current descr is not empty, it will signal an -interrupt, and halt processing. - -The tail pointer tails or trails the hardware pointer. When the -hardware is ahead, the tail pointer will be pointing at a "full" -descr. The OS will process this descr, and then mark it "not-in-use", -and advance the tail pointer. Thus, when there is flowing RX traffic, -all of the descrs in front of the tail pointer should be "full", and -all of those behind it should be "not-in-use". When RX traffic is not -flowing, then the tail pointer can catch up to the hardware pointer. -The OS will then note that the current tail is "empty", and halt -processing. - -The head pointer (somewhat mis-named) follows after the tail pointer. -When traffic is flowing, then the head pointer will be pointing at -a "not-in-use" descr. The OS will perform various housekeeping duties -on this descr. This includes allocating a new data buffer and -dma-mapping it so as to make it visible to the hardware. The OS will -then mark the descr as "empty", ready to receive data. Thus, when there -is flowing RX traffic, everything in front of the head pointer should -be "not-in-use", and everything behind it should be "empty". If no -RX traffic is flowing, then the head pointer can catch up to the tail -pointer, at which point the OS will notice that the head descr is -"empty", and it will halt processing. - -Thus, in an idle system, the GDACTDPA, tail and head pointers will -all be pointing at the same descr, which should be "empty". All of the -other descrs in the ring should be "empty" as well. - -The show_rx_chain() routine will print out the locations of the -GDACTDPA, tail and head pointers. It will also summarize the contents -of the ring, starting at the tail pointer, and listing the status -of the descrs that follow. - -A typical example of the output, for a nearly idle system, might be:: - - net eth1: Total number of descrs=256 - net eth1: Chain tail located at descr=20 - net eth1: Chain head is at 20 - net eth1: HW curr desc (GDACTDPA) is at 21 - net eth1: Have 1 descrs with stat=x40800101 - net eth1: HW next desc (GDACNEXTDA) is at 22 - net eth1: Last 255 descrs with stat=xa0800000 - -In the above, the hardware has filled in one descr, number 20. Both -head and tail are pointing at 20, because it has not yet been emptied. -Meanwhile, hw is pointing at 21, which is free. - -The "Have nnn decrs" refers to the descr starting at the tail: in this -case, nnn=1 descr, starting at descr 20. The "Last nnn descrs" refers -to all of the rest of the descrs, from the last status change. The "nnn" -is a count of how many descrs have exactly the same status. - -The status x4... corresponds to "full" and status xa... corresponds -to "empty". The actual value printed is RXCOMST_A. - -In the device driver source code, a different set of names are -used for these same concepts, so that:: - - "empty" == SPIDER_NET_DESCR_CARDOWNED == 0xa - "full" == SPIDER_NET_DESCR_FRAME_END == 0x4 - "not in use" == SPIDER_NET_DESCR_NOT_IN_USE == 0xf - - -The RX RAM full bug/feature -=========================== - -As long as the OS can empty out the RX buffers at a rate faster than -the hardware can fill them, there is no problem. If, for some reason, -the OS fails to empty the RX ring fast enough, the hardware GDACTDPA -pointer will catch up to the head, notice the not-empty condition, -ad stop. However, RX packets may still continue arriving on the wire. -The spidernet chip can save some limited number of these in local RAM. -When this local ram fills up, the spider chip will issue an interrupt -indicating this (GHIINT0STS will show ERRINT, and the GRMFLLINT bit -will be set in GHIINT1STS). When the RX ram full condition occurs, -a certain bug/feature is triggered that has to be specially handled. -This section describes the special handling for this condition. - -When the OS finally has a chance to run, it will empty out the RX ring. -In particular, it will clear the descriptor on which the hardware had -stopped. However, once the hardware has decided that a certain -descriptor is invalid, it will not restart at that descriptor; instead -it will restart at the next descr. This potentially will lead to a -deadlock condition, as the tail pointer will be pointing at this descr, -which, from the OS point of view, is empty; the OS will be waiting for -this descr to be filled. However, the hardware has skipped this descr, -and is filling the next descrs. Since the OS doesn't see this, there -is a potential deadlock, with the OS waiting for one descr to fill, -while the hardware is waiting for a different set of descrs to become -empty. - -A call to show_rx_chain() at this point indicates the nature of the -problem. A typical print when the network is hung shows the following:: - - net eth1: Spider RX RAM full, incoming packets might be discarded! - net eth1: Total number of descrs=256 - net eth1: Chain tail located at descr=255 - net eth1: Chain head is at 255 - net eth1: HW curr desc (GDACTDPA) is at 0 - net eth1: Have 1 descrs with stat=xa0800000 - net eth1: HW next desc (GDACNEXTDA) is at 1 - net eth1: Have 127 descrs with stat=x40800101 - net eth1: Have 1 descrs with stat=x40800001 - net eth1: Have 126 descrs with stat=x40800101 - net eth1: Last 1 descrs with stat=xa0800000 - -Both the tail and head pointers are pointing at descr 255, which is -marked xa... which is "empty". Thus, from the OS point of view, there -is nothing to be done. In particular, there is the implicit assumption -that everything in front of the "empty" descr must surely also be empty, -as explained in the last section. The OS is waiting for descr 255 to -become non-empty, which, in this case, will never happen. - -The HW pointer is at descr 0. This descr is marked 0x4.. or "full". -Since its already full, the hardware can do nothing more, and thus has -halted processing. Notice that descrs 0 through 254 are all marked -"full", while descr 254 and 255 are empty. (The "Last 1 descrs" is -descr 254, since tail was at 255.) Thus, the system is deadlocked, -and there can be no forward progress; the OS thinks there's nothing -to do, and the hardware has nowhere to put incoming data. - -This bug/feature is worked around with the spider_net_resync_head_ptr() -routine. When the driver receives RX interrupts, but an examination -of the RX chain seems to show it is empty, then it is probable that -the hardware has skipped a descr or two (sometimes dozens under heavy -network conditions). The spider_net_resync_head_ptr() subroutine will -search the ring for the next full descr, and the driver will resume -operations there. Since this will leave "holes" in the ring, there -is also a spider_net_resync_tail_ptr() that will skip over such holes. - -As of this writing, the spider_net_resync() strategy seems to work very -well, even under heavy network loads. - - -The TX ring -=========== -The TX ring uses a low-watermark interrupt scheme to make sure that -the TX queue is appropriately serviced for large packet sizes. - -For packet sizes greater than about 1KBytes, the kernel can fill -the TX ring quicker than the device can drain it. Once the ring -is full, the netdev is stopped. When there is room in the ring, -the netdev needs to be reawakened, so that more TX packets are placed -in the ring. The hardware can empty the ring about four times per jiffy, -so its not appropriate to wait for the poll routine to refill, since -the poll routine runs only once per jiffy. The low-watermark mechanism -marks a descr about 1/4th of the way from the bottom of the queue, so -that an interrupt is generated when the descr is processed. This -interrupt wakes up the netdev, which can then refill the queue. -For large packets, this mechanism generates a relatively small number -of interrupts, about 1K/sec. For smaller packets, this will drop to zero -interrupts, as the hardware can empty the queue faster than the kernel -can fill it. diff --git a/Documentation/networking/device_drivers/index.rst b/Documentation/networking/device_drivers/index.rst index 0dd30a84ce25..a254af25b7ef 100644 --- a/Documentation/networking/device_drivers/index.rst +++ b/Documentation/networking/device_drivers/index.rst @@ -9,7 +9,6 @@ Contents: :maxdepth: 2 atm/index - cable/index can/index cellular/index ethernet/index diff --git a/Documentation/networking/device_drivers/wwan/t7xx.rst b/Documentation/networking/device_drivers/wwan/t7xx.rst index f346f5f85f15..e07de7700dfc 100644 --- a/Documentation/networking/device_drivers/wwan/t7xx.rst +++ b/Documentation/networking/device_drivers/wwan/t7xx.rst @@ -7,12 +7,13 @@ ============================================ t7xx driver for MTK PCIe based T700 5G modem ============================================ -The t7xx driver is a WWAN PCIe host driver developed for linux or Chrome OS platforms -for data exchange over PCIe interface between Host platform & MediaTek's T700 5G modem. -The driver exposes an interface conforming to the MBIM protocol [1]. Any front end -application (e.g. Modem Manager) could easily manage the MBIM interface to enable -data communication towards WWAN. The driver also provides an interface to interact -with the MediaTek's modem via AT commands. +The t7xx driver is a WWAN PCIe host driver developed for linux or Chrome OS +platforms for data exchange over PCIe interface between Host platform & +MediaTek's T700 5G modem. +The driver exposes an interface conforming to the MBIM protocol [1]. Any front +end application (e.g. Modem Manager) could easily manage the MBIM interface to +enable data communication towards WWAN. The driver also provides an interface +to interact with the MediaTek's modem via AT commands. Basic usage =========== @@ -45,8 +46,8 @@ The driver provides sysfs interfaces to userspace. t7xx_mode --------- -The sysfs interface provides userspace with access to the device mode, this interface -supports read and write operations. +The sysfs interface provides userspace with access to the device mode, this +interface supports read and write operations. Device mode: @@ -67,6 +68,28 @@ Write from userspace to set the device mode. :: $ echo fastboot_switching > /sys/bus/pci/devices/${bdf}/t7xx_mode +t7xx_debug_ports +---------------- +The sysfs interface provides userspace with access to enable/disable the debug +ports, this interface supports read and write operations. + +Debug port status: + +- ``1`` represents enable debug ports +- ``0`` represents disable debug ports + +Currently supported debug ports (ADB/MIPC). + +Read from userspace to get the current debug ports status. + +:: + $ cat /sys/bus/pci/devices/${bdf}/t7xx_debug_ports + +Write from userspace to set the debug ports status. + +:: + $ echo 1 > /sys/bus/pci/devices/${bdf}/t7xx_debug_ports + Management application development ================================== The driver and userspace interfaces are described below. The MBIM protocol is @@ -139,6 +162,25 @@ Please note that driver needs to be reloaded to export /dev/wwan0fastboot0 port, because device needs a cold reset after enter ``fastboot_switching`` mode. +ADB port userspace ABI +---------------------- + +/dev/wwan0adb0 character device +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +The driver exposes a ADB protocol interface by implementing ADB WWAN Port. +The userspace end of the ADB channel pipe is a /dev/wwan0adb0 character device. +Application shall use this interface for ADB protocol communication. + +MIPC port userspace ABI +----------------------- + +/dev/wwan0mipc0 character device +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +The driver exposes a diagnostic interface by implementing MIPC (Modem +Information Process Center) WWAN Port. The userspace end of the MIPC channel +pipe is a /dev/wwan0mipc0 character device. +Application shall use this interface for MTK modem diagnostic communication. + The MediaTek's T700 modem supports the 3GPP TS 27.007 [4] specification. References @@ -164,3 +206,9 @@ speak the Mobile Interface Broadband Model (MBIM) protocol"* [5] *fastboot "a mechanism for communicating with bootloaders"* - https://android.googlesource.com/platform/system/core/+/refs/heads/main/fastboot/README.md + +[6] *ADB (Android Debug Bridge) "a mechanism to keep track of Android devices +and emulators instances connected to or running on a given host developer +machine with ADB protocol"* + +- https://android.googlesource.com/platform/packages/modules/adb/+/refs/heads/main/README.md |