diff options
Diffstat (limited to 'arch/arc/boot/dts/axc003_idu.dtsi')
| -rw-r--r-- | arch/arc/boot/dts/axc003_idu.dtsi | 81 |
1 files changed, 59 insertions, 22 deletions
diff --git a/arch/arc/boot/dts/axc003_idu.dtsi b/arch/arc/boot/dts/axc003_idu.dtsi index 695f9fa1996b..f31382cb8be4 100644 --- a/arch/arc/boot/dts/axc003_idu.dtsi +++ b/arch/arc/boot/dts/axc003_idu.dtsi @@ -1,9 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-only /* * Copyright (C) 2014, 2015 Synopsys, Inc. (www.synopsys.com) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. */ /* @@ -14,20 +11,35 @@ / { compatible = "snps,arc"; - #address-cells = <1>; - #size-cells = <1>; + #address-cells = <2>; + #size-cells = <2>; cpu_card { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; - ranges = <0x00000000 0xf0000000 0x10000000>; + ranges = <0x00000000 0x0 0xf0000000 0x10000000>; - core_clk: core_clk { + input_clk: input-clk { #clock-cells = <0>; compatible = "fixed-clock"; - clock-frequency = <100000000>; + clock-frequency = <33333333>; + }; + + core_clk: core-clk@80 { + compatible = "snps,axs10x-arc-pll-clock"; + reg = <0x80 0x10>, <0x100 0x10>; + #clock-cells = <0>; + clocks = <&input_clk>; + + /* + * Set initial core pll output frequency to 100MHz. + * It will be applied at the core pll driver probing + * on early boot. + */ + assigned-clocks = <&core_clk>; + assigned-clock-rates = <100000000>; }; core_intc: archs-intc@cpu { @@ -47,7 +59,7 @@ * this GPIO block ORs all interrupts on CPU card (creg,..) * to uplink only 1 IRQ to ARC core intc */ - dw-apb-gpio@0x2000 { + dw-apb-gpio@2000 { compatible = "snps,dw-apb-gpio"; reg = < 0x2000 0x80 >; #address-cells = <1>; @@ -57,7 +69,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <30>; + ngpios = <30>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -66,7 +78,7 @@ }; }; - debug_uart: dw-apb-uart@0x5000 { + debug_uart: dw-apb-uart@5000 { compatible = "snps,dw-apb-uart"; reg = <0x5000 0x100>; clock-frequency = <33333000>; @@ -86,6 +98,32 @@ }; /* + * Mark DMA peripherals connected via IOC port as dma-coherent. We do + * it via overlay because peripherals defined in axs10x_mb.dtsi are + * used for both AXS101 and AXS103 boards and only AXS103 has IOC (so + * only AXS103 board has HW-coherent DMA peripherals) + * We don't need to mark pgu@17000 as dma-coherent because it uses + * external DMA buffer located outside of IOC aperture. + */ + axs10x_mb { + ethernet@18000 { + dma-coherent; + }; + + usb@40000 { + dma-coherent; + }; + + usb@60000 { + dma-coherent; + }; + + mmc@15000 { + dma-coherent; + }; + }; + + /* * This INTC is actually connected to DW APB GPIO * which acts as a wire between MB INTC and CPU INTC. * GPIO INTC is configured in platform init code @@ -97,33 +135,32 @@ * avoid duplicating the MB dtsi file given that IRQ from * this intc to cpu intc are different for axs101 and axs103 */ - mb_intc: dw-apb-ictl@0xe0012000 { + mb_intc: interrupt-controller@e0012000 { #interrupt-cells = <1>; compatible = "snps,dw-apb-ictl"; - reg = < 0xe0012000 0x200 >; + reg = < 0x0 0xe0012000 0x0 0x200 >; interrupt-controller; interrupt-parent = <&idu_intc>; interrupts = <0>; }; memory { - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x00000000 0x80000000 0x40000000>; device_type = "memory"; - reg = <0x80000000 0x20000000>; /* 512MiB */ + /* CONFIG_LINUX_RAM_BASE needs to match low mem start */ + reg = <0x0 0x80000000 0x0 0x20000000 /* 512 MiB low mem */ + 0x1 0xc0000000 0x0 0x40000000>; /* 1 GiB highmem */ }; reserved-memory { - #address-cells = <1>; - #size-cells = <1>; + #address-cells = <2>; + #size-cells = <2>; ranges; /* - * Move frame buffer out of IOC aperture (0x8z-0xAz). + * Move frame buffer out of IOC aperture (0x8z-0xaz). */ frame_buffer: frame_buffer@be000000 { compatible = "shared-dma-pool"; - reg = <0xbe000000 0x2000000>; + reg = <0x0 0xbe000000 0x0 0x2000000>; no-map; }; }; |