diff options
Diffstat (limited to 'arch/arm/boot/dts/intel/ixp')
23 files changed, 2794 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/intel/ixp/Makefile b/arch/arm/boot/dts/intel/ixp/Makefile new file mode 100644 index 000000000000..1a25ce3cf84f --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/Makefile @@ -0,0 +1,19 @@ +# SPDX-License-Identifier: GPL-2.0 +dtb-$(CONFIG_ARCH_IXP4XX) += \ + intel-ixp42x-linksys-nslu2.dtb \ + intel-ixp42x-linksys-wrv54g.dtb \ + intel-ixp42x-freecom-fsg-3.dtb \ + intel-ixp42x-welltech-epbx100.dtb \ + intel-ixp42x-ixdp425.dtb \ + intel-ixp43x-kixrp435.dtb \ + intel-ixp46x-ixdp465.dtb \ + intel-ixp42x-adi-coyote.dtb \ + intel-ixp42x-ixdpg425.dtb \ + intel-ixp42x-goramo-multilink.dtb \ + intel-ixp42x-iomega-nas100d.dtb \ + intel-ixp42x-dlink-dsm-g600.dtb \ + intel-ixp42x-gateworks-gw2348.dtb \ + intel-ixp43x-gateworks-gw2358.dtb \ + intel-ixp42x-netgear-wg302v1.dtb \ + intel-ixp42x-arcom-vulcan.dtb \ + intel-ixp42x-gateway-7001.dtb diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-adi-coyote.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-adi-coyote.dts new file mode 100644 index 000000000000..765ab36e6f0c --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-adi-coyote.dts @@ -0,0 +1,112 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for ADI Engineering Coyote platform. + * Derived from boardfiles written by MontaVista software. + * Ethernet set-up from OpenWrt. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "ADI Engineering Coyote reference design"; + compatible = "adieng,coyote", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* CHECKME: 16 MB SDRAM minimum, maybe the Coyote actually has more */ + device_type = "memory"; + reg = <0x00000000 0x01000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait"; + stdout-path = "uart1:115200n8"; + }; + + aliases { + /* These are switched around */ + serial0 = &uart1; + serial1 = &uart0; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 32 MB of Flash in 128 0x20000 sized blocks + * mapped in at CS0 and CS1 + */ + reg = <0 0x00000000 0x2000000>; + + /* Configure expansion bus to allow writes */ + intel,ixp4xx-eb-write-enable = <1>; + + partitions { + compatible = "redboot-fis"; + /* CHECKME: guess this is Redboot FIS */ + fis-index-block = <0x1ff>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from Coyote PCI boardfile. + * We have slots (IDSEL) 1 and 2 with one assigned IRQ + * each handling all IRQs. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 6 */ + <0x0800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 6 */ + <0x0800 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 6 */ + <0x0800 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 6 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */ + <0x1000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 11 */ + <0x1000 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 11 */ + <0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 11 */ + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-arcom-vulcan.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-arcom-vulcan.dts new file mode 100644 index 000000000000..6f5b4e4eb1cc --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-arcom-vulcan.dts @@ -0,0 +1,169 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Arcom/Eurotech Vulcan board. + * This board is a single board computer in the PC/104 form factor based on + * IXP425, and was released around 2005. It previously had the name "Mercury". + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Arcom/Eurotech Vulcan"; + compatible = "arcom,vulcan", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + /* CHECKME: using a harddrive at /dev/sda1 as rootfs by default */ + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + onewire { + compatible = "w1-gpio"; + gpios = <&gpio0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 32 MB of Flash in 0x20000 byte blocks + * mapped in at CS0 and CS1. + * + * The documentation mentions the existence + * of a 16MB version, which we conveniently + * ignore. Shout if you own one! + */ + reg = <0 0x00000000 0x2000000>; + + /* Expansion bus settings */ + intel,ixp4xx-eb-t3 = <3>; + intel,ixp4xx-eb-byte-access-on-halfword = <1>; + intel,ixp4xx-eb-write-enable = <1>; + + partitions { + compatible = "redboot-fis"; + fis-index-block = <0x1ff>; + }; + }; + sram@2,0 { + /* 256 KB SDRAM memory at CS2 */ + compatible = "shared-dma-pool"; + device_type = "memory"; + reg = <2 0x00000000 0x40000>; + no-map; + /* Expansion bus settings */ + intel,ixp4xx-eb-t3 = <1>; + intel,ixp4xx-eb-t4 = <2>; + intel,ixp4xx-eb-ahb-split-transfers = <1>; + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + serial@3,0 { + /* + * 8250-compatible Exar XR16L2551 2 x UART + * + * CHECKME: if special tweaks are needed, then fix the + * operating system to handle it. + */ + compatible = "exar,xr16l2551", "ns8250"; + reg = <3 0x00000000 0x10>; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + clock-frequency = <1843200>; + /* Expansion bus settings */ + intel,ixp4xx-eb-t3 = <3>; + intel,ixp4xx-eb-cycle-type = <1>; /* Motorola cycles */ + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + gpio1: gpio@4,0 { + /* + * MMIO GPIO in one byte + */ + compatible = "arcom,vulcan-gpio"; + reg = <4 0x00000000 0x1>; + /* Expansion bus settings */ + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + watchdog@5,0 { + compatible = "maxim,max6369"; + reg = <5 0x00000000 0x1>; + /* Expansion bus settings */ + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from Vulcan PCI boardfile. + * + * We have 2 slots (IDSEL) 1 and 2 with one dedicated interrupt + * per slot. This interrupt is shared (OR:ed) by all four pins. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 2 */ + <0x0800 0 0 2 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 2 */ + <0x0800 0 0 3 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 2 */ + <0x0800 0 0 4 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 2 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 3 */ + <0x1000 0 0 2 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 3 */ + <0x1000 0 0 3 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 3 */ + <0x1000 0 0 4 &gpio0 3 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 3 */ + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-dlink-dsm-g600.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-dlink-dsm-g600.dts new file mode 100644 index 000000000000..b9d46eb06507 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-dlink-dsm-g600.dts @@ -0,0 +1,147 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for D-Link DSM-G600 revision A based on IXP420 + * NOTE: revision B of this device uses PowerPC and is NOT supported by + * this device tree. + * + * Inspired by the boardfile by Rod Whitby, Tower Technologies, Alessandro Zummo + * and Michael Westerhof. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "D-Link DSM-G600 rev A"; + compatible = "dlink,dsm-g600-a", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 64 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + leds { + compatible = "gpio-leds"; + led-power { + label = "dsmg600:green:power"; + gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + led-wlan { + label = "dsmg600:green:wlan"; + /* CHECKME: flagged as active low in the old board file */ + gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + default-state = "on"; + /* We don't have WLAN trigger in the kernel (yet) */ + linux,default-trigger = "netdev"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button-reset { + wakeup-source; + linux,code = <KEY_ESC>; + label = "reset"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + }; + }; + + gpio_keys_polled { + compatible = "gpio-keys-polled"; + + /* + * According to the board file this key cannot handle interrupts and + * need to be polled. Investigate if this is really the case or if + * this can be moved adjacent to the ordinary gpio-keys above. + */ + button-power { + wakeup-source; + linux,code = <KEY_POWER>; + label = "power"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; + timeout-ms = <5000>; + }; + + soc { + bus@c4000000 { + /* The first 16MB region at CS0 on the expansion bus */ + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 16 MB of Flash in 128 0x20000 sized blocks + * mapped in at CS0. + */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "redboot-fis"; + /* + * A boot log says the directory is at 0xfe0000 + * 0x7f * 0x20000 = 0xfe0000 + */ + fis-index-block = <0x7f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from DSM-G600 PCI boardfile (dsmg600-pci.c) + * We have slots (IDSEL) 1, 2, 3, 4 and pins 1, 2 and 3. + * Only slot 3 have three IRQs. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT E on slot 1 is irq 7 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 10 */ + <0x1800 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 9 */ + <0x1800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 8 */ + /* IDSEL 4 */ + <0x2000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT F on slot 4 is irq 6 */ + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-freecom-fsg-3.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-freecom-fsg-3.dts new file mode 100644 index 000000000000..5a5e16cc7335 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-freecom-fsg-3.dts @@ -0,0 +1,219 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Freecom FSG-3 router. + * This machine is based on IXP425. + * This device tree is inspired by the board file by Rod Whitby. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Freecom FSG-3"; + compatible = "freecom,fsg-3", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 64 MB memory */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + /* Boot from the first partition on the hard drive */ + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button-sync { + wakeup-source; + /* Closest approximation of what the key should do */ + linux,code = <KEY_CONNECT>; + label = "sync"; + gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + }; + button-reset { + wakeup-source; + linux,code = <KEY_ESC>; + label = "reset"; + gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; + }; + button-usb { + wakeup-source; + /* Unplug USB, closest approximation of what the key should do */ + linux,code = <KEY_EJECTCD>; + label = "usb"; + gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + hwmon@28 { + /* + * Temperature sensor and fan control chip. + * + * TODO: create a proper device tree binding for + * the sensor and temperature zone and create a + * zone with fan control. + */ + compatible = "winbond,w83781d"; + reg = <0x28>; + }; + rtc@6f { + compatible = "isil,isl1208"; + reg = <0x6f>; + }; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 4 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x400000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x3e0000 */ + fis-index-block = <0x1f>; + }; + }; + + /* Small syscon with some LEDs at CS2 */ + syscon@2,0 { + compatible = "freecom,fsg-cs2-system-controller", "syscon"; + reg = <2 0x0 0x200>; + reg-io-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <2 0x0 0x0 0x200>; + + led@0,0 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x01>; + label = "fsg:blue:wlan"; + linux,default-trigger = "wlan"; + default-state = "on"; + }; + led@0,1 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x02>; + label = "fsg:blue:wan"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,2 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x04>; + label = "fsg:blue:sata"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,3 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x04>; + label = "fsg:blue:usb"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,4 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x08>; + label = "fsg:blue:sync"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,5 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x10>; + label = "fsg:blue:ring"; + linux,default-trigger = ""; + default-state = "on"; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Written based on the FSG-3 PCI boardfile. + * We have slots 12, 13 & 14 (IDSEL) with one IRQ each. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 12 */ + <0x6000 0 0 1 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 5 */ + <0x6000 0 0 2 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 5 */ + <0x6000 0 0 3 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 5 */ + <0x6000 0 0 4 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 5 */ + /* IDSEL 13 */ + <0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */ + <0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */ + <0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */ + <0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */ + /* IDSEL 14 */ + <0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */ + <0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */ + <0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */ + <0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */ + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateway-7001.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateway-7001.dts new file mode 100644 index 000000000000..4d70f6afd13a --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateway-7001.dts @@ -0,0 +1,110 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Gateway 7001 AP based on IXP422 + * Derived from boardfiles written by Imre Kaloz + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Gateway 7001 AP"; + compatible = "gateway,7001", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x2000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "uart1:115200n8"; + }; + + aliases { + /* second UART is the primary console */ + serial0 = &uart1; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 8 MB of flash + */ + reg = <0 0x00000000 0x800000>; + + /* Configure expansion bus to allow writes */ + intel,ixp4xx-eb-write-enable = <1>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x7e0000 */ + fis-index-block = <0x3f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from Gateway 7001 PCI boardfile (gateway7001-pci.c) + * We have slots (IDSEL) 1 and 2 with one assigned IRQ + * each handling all IRQs. + */ + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 11 */ + <0x0800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 11 */ + <0x0800 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 11 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + <0x1000 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 10 */ + <0x1000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 10 */ + <0x1000 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 10 */ + }; + + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy2>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateworks-gw2348.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateworks-gw2348.dts new file mode 100644 index 000000000000..97e3f25bb210 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateworks-gw2348.dts @@ -0,0 +1,174 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Gateworks Avila GW2348 board. + * This machine is based on IXP425. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Gateworks Avila GW2348"; + compatible = "gateworks,gw2348", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + leds { + compatible = "gpio-leds"; + led-user { + label = "gw2348:green:user"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + hwmon@28 { + compatible = "adi,ad7418"; + reg = <0x28>; + }; + rtc: ds1672@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; + eeprom@51 { + compatible = "atmel,24c08"; + reg = <0x51>; + pagesize = <16>; + size = <1024>; + read-only; + }; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 16 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x0fe0000 */ + fis-index-block = <0x7f>; + }; + }; + ide@1,0 { + compatible = "intel,ixp4xx-compact-flash"; + /* + * Set up expansion bus config to a really slow timing. + * The CF driver will dynamically reconfigure these timings + * depending on selected PIO mode (0-4). + */ + intel,ixp4xx-eb-t1 = <3>; // 3 cycles extra address phase + intel,ixp4xx-eb-t2 = <3>; // 3 cycles extra setup phase + intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase + intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase + intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase + intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type + intel,ixp4xx-eb-byte-access-on-halfword = <1>; + intel,ixp4xx-eb-mux-address-and-data = <0>; + intel,ixp4xx-eb-ahb-split-transfers = <0>; + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + /* First register set is CMD second is CTL (notice it uses CS2) */ + reg = <1 0x00000000 0x1000000>, <2 0x00000000 0x1000000>; + interrupt-parent = <&gpio0>; + interrupts = <12 IRQ_TYPE_EDGE_RISING>; + }; + /* + * FIXME: Latch LEDs or extra UARTs at CS4 + */ + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from Avila PCI boardfile. + * + * We have up to 4 slots (IDSEL) with 4 swizzled IRQs. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ + <0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ + <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ + <0x1000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */ + <0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ + <0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */ + <0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */ + <0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */ + /* IDSEL 4 */ + <0x2000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */ + <0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */ + <0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */ + <0x2000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */ + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-goramo-multilink.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-goramo-multilink.dts new file mode 100644 index 000000000000..9ec0169bacf8 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-goramo-multilink.dts @@ -0,0 +1,180 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Goramo MultiLink Router + * There are two variants: + * - MultiLink Basic (a box) + * - MultiLink Max (19" rack mount) + * This device tree supports MultiLink Basic. + * This machine is based on IXP425. + * This is one of the few devices supporting the IXP4xx High-Speed Serial + * (HSS) link for a V.35 WAN interface. + * The hardware originates in Poland. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Goramo MultiLink Router"; + compatible = "goramo,multilink-router", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* + * 64 MB of RAM according to the manual. The MultiLink + * Max has 128 MB. + */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + }; + + /* + * 74HC4094 which is used as a rudimentary GPIO expander + * FIXME: + * - Create device tree bindings for this as GPIO expander + * - Write a pure DT GPIO driver using these bindings + * - Support cascading in the style of gpio-74x164.c (cannot be reused, very different) + */ + gpio_74: gpio-74hc4094 { + compatible = "nxp,74hc4094"; + cp-gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + d-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + str-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; + /* oe-gpios is optional */ + gpio-controller; + #gpio-cells = <2>; + /* We are not cascaded */ + registers-number = <1>; + gpio-line-names = "CONTROL_HSS0_CLK_INT", "CONTROL_HSS1_CLK_INT", "CONTROL_HSS0_DTR_N", + "CONTROL_HSS1_DTR_N", "CONTROL_EXT", "CONTROL_AUTO_RESET", + "CONTROL_PCI_RESET_N", "CONTROL_EEPROM_WC_N"; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 16 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x0fe0000 */ + fis-index-block = <0x7f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * The device has 4 slots (IDSEL) with one dedicated IRQ per slot. + * The slots have Ethernet, Ethernet, NEC and MPCI. + * The IDSELs are 11, 12, 13, 14. + */ + interrupt-map = + /* IDSEL 11 - Ethernet A */ + <0x5800 0 0 1 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 11 is irq 4 */ + <0x5800 0 0 2 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 11 is irq 4 */ + <0x5800 0 0 3 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 11 is irq 4 */ + <0x5800 0 0 4 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 11 is irq 4 */ + /* IDSEL 12 - Ethernet B */ + <0x6000 0 0 1 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 5 */ + <0x6000 0 0 2 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 5 */ + <0x6000 0 0 3 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 5 */ + <0x6000 0 0 4 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 5 */ + /* IDSEL 13 - MPCI */ + <0x6800 0 0 1 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 12 */ + <0x6800 0 0 2 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 12 */ + <0x6800 0 0 3 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 12 */ + <0x6800 0 0 4 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 12 */ + /* IDSEL 14 - NEC */ + <0x7000 0 0 1 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 3 */ + <0x7000 0 0 2 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 3 */ + <0x7000 0 0 3 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 3 */ + <0x7000 0 0 4 &gpio0 3 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 3 */ + }; + + /* HSS links */ + npe@c8006000 { + hss@0 { + status = "okay"; + intel,queue-chl-rxtrig = <&qmgr 12>; + intel,queue-chl-txready = <&qmgr 34>; + intel,queue-pkt-rx = <&qmgr 13>; + intel,queue-pkt-tx = <&qmgr 14>, <&qmgr 15>, <&qmgr 16>, <&qmgr 17>; + intel,queue-pkt-rxfree = <&qmgr 18>, <&qmgr 19>, <&qmgr 20>, <&qmgr 21>; + intel,queue-pkt-txdone = <&qmgr 22>; + /* The Goramo GPIO-based clock etc control */ + cts-gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; + dtr-gpios = <&gpio_74 2 GPIO_ACTIVE_LOW>; + clk-internal-gpios = <&gpio_74 0 GPIO_ACTIVE_HIGH>; + }; + hss@1 { + status = "okay"; + intel,queue-chl-rxtrig = <&qmgr 10>; + intel,queue-chl-txready = <&qmgr 35>; + intel,queue-pkt-rx = <&qmgr 0>; + intel,queue-pkt-tx = <&qmgr 5>, <&qmgr 6>, <&qmgr 7>, <&qmgr 8>; + intel,queue-pkt-rxfree = <&qmgr 1>, <&qmgr 2>, <&qmgr 3>, <&qmgr 4>; + intel,queue-pkt-txdone = <&qmgr 9>; + /* The Goramo GPIO-based clock etc control */ + cts-gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; + dtr-gpios = <&gpio_74 3 GPIO_ACTIVE_LOW>; + clk-internal-gpios = <&gpio_74 1 GPIO_ACTIVE_HIGH>; + }; + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 32>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 33>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-iomega-nas100d.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-iomega-nas100d.dts new file mode 100644 index 000000000000..8da6823e1dbe --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-iomega-nas100d.dts @@ -0,0 +1,148 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Iomega NAS 100D + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Iomega NAS 100D"; + compatible = "iom,nas-100d", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 64 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + leds { + compatible = "gpio-leds"; + led-wlan { + label = "nas100d:red:wlan"; + gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + default-state = "on"; + /* We don't have WLAN trigger in the kernel (yet) */ + linux,default-trigger = "netdev"; + }; + led-disk { + label = "nas100d:red:disk"; + gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "disk-activity"; + }; + led-power { + label = "nas100d:red:power"; + gpios = <&gpio0 15 GPIO_ACTIVE_LOW>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button-power { + wakeup-source; + linux,code = <KEY_POWER>; + label = "power"; + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + }; + button-reset { + wakeup-source; + linux,code = <KEY_ESC>; + label = "reset"; + gpios = <&gpio0 4 GPIO_ACTIVE_LOW>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + timeout-ms = <5000>; + }; + + soc { + bus@c4000000 { + /* The first 16MB region at CS0 on the expansion bus */ + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 8 MB of Flash in 0x20000 byte blocks + * mapped in at CS0. + */ + reg = <0 0x00000000 0x800000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x7e0000 */ + fis-index-block = <0x3f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from NAS 100D PCI boardfile (nas100d-pci.c) + * We have slots (IDSEL) 1, 2 and 3 and pins 1, 2 and 3. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ + <0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */ + <0x1800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>; /* INT C on slot 3 is irq 7 */ + }; + + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdp425.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdp425.dts new file mode 100644 index 000000000000..194945748dc3 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdp425.dts @@ -0,0 +1,72 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Intel IXDP425 also known as IXCDP1100 Control Plane + * processor reference design. + * + * This platform has the codename "Richfield". + * + * This machine is based on a 533 MHz IXP425. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include "intel-ixp4xx-reference-design.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Intel IXDP425/IXCDP1100 Richfield Reference Design"; + compatible = "intel,ixdp425", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 16 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x0fe0000 */ + fis-index-block = <0x7f>; + }; + }; + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdpg425.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdpg425.dts new file mode 100644 index 000000000000..7011fea6205b --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdpg425.dts @@ -0,0 +1,127 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Intel IXDPG425 reference design. + * Derived from boardfiles written by MontaVista software. + * Ethernet set-up from OpenWrt. + * + * The device has 4 x FXS RJ11 ports for analog phones for + * internet telephony. (Not supported yet.) + * + * The device has 9 status LEDs we do not support yet. + * + * This device is very similar to ADI engingeering Coyote. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Intel IXDPG425 reference design"; + compatible = "intel,ixdpg425", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x02000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * CHECKME: the product brief says 16MB in a flash + * socket. + */ + reg = <0 0x00000000 0x1000000>; + + /* Configure expansion bus to allow writes */ + intel,ixp4xx-eb-write-enable = <1>; + + partitions { + compatible = "redboot-fis"; + /* CHECKME: guess this is Redboot FIS */ + fis-index-block = <0x7f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from IXDPG425 PCI boardfile. + * We have slots (IDSEL) 12, 13 and 14 with one assigned IRQ + * for 12 & 13 and one for 14. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 12 */ + <0x6000 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 7 */ + <0x6000 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 7 */ + <0x6000 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 7 */ + <0x6000 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 7 */ + /* IDSEL 13 */ + <0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */ + <0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */ + <0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */ + <0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */ + /* IDSEL 14 */ + <0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */ + <0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */ + <0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */ + <0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */ + }; + + /* + * CHECKME: this ethernet setup seems dubious. Photos of the board shows some kind + * of Realtek DSA switch on the board. + */ + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-nslu2.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-nslu2.dts new file mode 100644 index 000000000000..da1e93212b86 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-nslu2.dts @@ -0,0 +1,162 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Linksys NSLU2 + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Linksys NSLU2 (Network Storage Link for USB 2.0 Disk Drives)"; + compatible = "linksys,nslu2", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x2000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + leds { + compatible = "gpio-leds"; + led-status { + label = "nslu2:red:status"; + gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + led-ready { + label = "nslu2:green:ready"; + gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + led-disk-1 { + label = "nslu2:green:disk-1"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + led-disk-2 { + label = "nslu2:green:disk-2"; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button-power { + wakeup-source; + linux,code = <KEY_POWER>; + label = "power"; + gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; + }; + button-reset { + wakeup-source; + linux,code = <KEY_ESC>; + label = "reset"; + gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@6f { + compatible = "xicor,x1205"; + reg = <0x6f>; + }; + }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; + timeout-ms = <5000>; + }; + + gpio-beeper { + compatible = "gpio-beeper"; + gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + }; + + soc { + bus@c4000000 { + /* The first 16MB region at CS0 on the expansion bus */ + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 8 MB of Flash in 0x20000 byte blocks + * mapped in at CS0. + */ + reg = <0 0x00000000 0x800000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x7e0000 */ + fis-index-block = <0x3f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from NSLU2 PCI boardfile, INT A, B, C swizzled D constant + * We have slots (IDSEL) 1, 2 and 3. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ + <0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ + <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ + <0x1000 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 11 */ + <0x1000 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 8 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ + <0x1800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */ + <0x1800 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */ + <0x1800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 3 is irq 8 */ + }; + + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-wrv54g.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-wrv54g.dts new file mode 100644 index 000000000000..4aba9e0214a0 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-wrv54g.dts @@ -0,0 +1,175 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Linksys WRV54G router + * Also known as Gemtek GTWX5715 + * Based on a board file by George T. Joseph and other patches. + * This machine is based on IXP425. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Linksys WRV54G / Gemtek GTWX5715"; + compatible = "linksys,wrv54g", "gemtek,gtwx5715", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB memory */ + device_type = "memory"; + reg = <0x00000000 0x2000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "uart1:115200n8"; + }; + + aliases { + /* UART2 is the primary console */ + serial0 = &uart1; + serial1 = &uart0; + }; + + /* There is an unpopulated LED slot (3) connected to GPIO 8 */ + leds { + compatible = "gpio-leds"; + led-power { + label = "wrv54g:yellow:power"; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + led-wireless { + label = "wrv54g:yellow:wireless"; + gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + led-internet { + label = "wrv54g:yellow:internet"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + led-dmz { + label = "wrv54g:green:dmz"; + gpios = <&gpio0 4 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + }; + + /* This set-up comes from an OpenWrt patch */ + spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sck-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + miso-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cs-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + num-chipselects = <1>; + + switch@0 { + compatible = "micrel,ks8995"; + reg = <0>; + spi-max-frequency = <50000000>; + }; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 8 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x00800000>; + + partitions { + compatible = "fixed-partitions"; + /* + * Partition info from a boot log + * CHECKME: not using redboot? FIS index 0x3f @7e00000? + */ + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "boot"; + reg = <0x0 0x140000>; + read-only; + }; + partition@140000 { + label = "linux"; + reg = <0x140000 0x100000>; + read-only; + }; + partition@240000 { + label = "root"; + reg = <0x240000 0x480000>; + read-write; + }; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * We have up to 2 slots (IDSEL) with 2 swizzled IRQs. + * Derived from the GTWX5715 PCI boardfile. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 0 */ + <0x0000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 0 is irq 10 */ + <0x0000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 0 is irq 11 */ + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>; /* INT B on slot 1 is irq 10 */ + }; + + /* + * EthB - connected to the KS8995 switch ports 1-4 + * FIXME: the boardfile defines .phy_mask = 0x1e for this port to enable output to + * all four switch ports, also using an out of tree multiphy patch. + * Do we need a new binding and property for this? + */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Should be ports 1-4 on the KS8995 switch */ + phy4: ethernet-phy@4 { + reg = <4>; + }; + + /* Should be port 5 on the KS8995 switch */ + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + + /* EthC - connected to KS8995 switch port 5 */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-netgear-wg302v1.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-netgear-wg302v1.dts new file mode 100644 index 000000000000..19d56e9aec9d --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-netgear-wg302v1.dts @@ -0,0 +1,96 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Netgear WG302v2 based on IXP422BB + * Derived from boardfiles written by Imre Kaloz + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Netgear WG302 v1"; + compatible = "netgear,wg302v1", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB SDRAM according to boot arguments */ + device_type = "memory"; + reg = <0x00000000 0x02000000>; + }; + + chosen { + /* The RedBoot comes up in 9600 baud so let's keep this */ + bootargs = "console=ttyS0,9600n8"; + stdout-path = "uart1:9600n8"; + }; + + aliases { + /* These are switched around */ + serial0 = &uart1; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 8 MB of Flash in 64 0x20000 sized blocks + * mapped in at CS0. + */ + reg = <0 0x00000000 0x800000>; + + /* Configure expansion bus to allow writes */ + intel,ixp4xx-eb-write-enable = <1>; + + partitions { + compatible = "redboot-fis"; + fis-index-block = <0x3f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from WG302 v2 PCI boardfile (wg302v2-pci.c) + * We have slots (IDSEL) 1 and 2 with one assigned IRQ + * each handling all IRQs. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 8 */ + <0x0800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 8 */ + <0x0800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 8 */ + <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 9 */ + <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ + <0x1000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 9 */ + <0x1000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 9 */ + }; + + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy30>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy30: ethernet-phy@30 { + reg = <30>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-welltech-epbx100.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-welltech-epbx100.dts new file mode 100644 index 000000000000..c550c421b659 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-welltech-epbx100.dts @@ -0,0 +1,98 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Corentin Labbe <clabbe@baylibre.com> + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" + +/ { + model = "Welltech EPBX100"; + compatible = "welltech,epbx100", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 64 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/ram0 initrd=0x00800000,9M"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 16 MB of Flash + */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "RedBoot"; + reg = <0x00000000 0x00080000>; + read-only; + }; + partition@80000 { + label = "zImage"; + reg = <0x00080000 0x00100000>; + read-only; + }; + partition@180000 { + label = "ramdisk"; + reg = <0x00180000 0x00300000>; + read-only; + }; + partition@480000 { + label = "User"; + reg = <0x00480000 0x00b60000>; + read-only; + }; + partition@fe0000 { + label = "FIS directory"; + reg = <0x00fe0000 0x001f000>; + read-only; + }; + partition@fff000 { + label = "RedBoot config"; + reg = <0x00fff000 0x0001000>; + read-only; + }; + }; + }; + }; + + /* LAN port */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp42x.dtsi new file mode 100644 index 000000000000..84cee8ec3ab8 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x.dtsi @@ -0,0 +1,34 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Intel XScale Network Processors + * in the IXP 42x series. This series has 32 interrupts. + */ +#include "intel-ixp4xx.dtsi" + +/ { + soc { + bus@c4000000 { + compatible = "intel,ixp42x-expansion-bus-controller", "syscon"; + reg = <0xc4000000 0x30>; + }; + + pci@c0000000 { + compatible = "intel,ixp42x-pci"; + }; + + interrupt-controller@c8003000 { + compatible = "intel,ixp42x-interrupt"; + }; + + /* + * This is the USB Device Mode (UDC) controller, which is used + * to present the IXP4xx as a device on a USB bus. + */ + usb@c800b000 { + compatible = "intel,ixp4xx-udc"; + reg = <0xc800b000 0x1000>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp43x-gateworks-gw2358.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-gateworks-gw2358.dts new file mode 100644 index 000000000000..1db849515f9e --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-gateworks-gw2358.dts @@ -0,0 +1,199 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Gateworks IXP43x-based Cambria GW2358 + */ + +/dts-v1/; + +#include "intel-ixp43x.dtsi" + +/ { + model = "Gateworks Cambria GW2358"; + compatible = "gateworks,gw2358", "intel,ixp43x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 128 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + leds { + compatible = "gpio-leds"; + led-user { + label = "gw2358:green:LED"; + gpios = <&pld1 0 GPIO_ACTIVE_LOW>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + }; + + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + hwmon@28 { + compatible = "adi,ad7418"; + reg = <0x28>; + }; + rtc: ds1672@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; + eeprom@51 { + compatible = "atmel,24c08"; + reg = <0x51>; + pagesize = <16>; + size = <1024>; + read-only; + }; + pld0: pld@56 { + compatible = "gateworks,pld-gpio"; + reg = <0x56>; + gpio-controller; + #gpio-cells = <2>; + }; + /* This PLD just handles the LED and user button */ + pld1: pld@57 { + compatible = "gateworks,pld-gpio"; + reg = <0x57>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* + * 32 MB of Flash in 0x20000 byte blocks + * mapped in at CS0 and CS1 + */ + reg = <0 0x00000000 0x2000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x1fe0000 */ + fis-index-block = <0xff>; + }; + }; + ide@3,0 { + compatible = "intel,ixp4xx-compact-flash"; + /* + * Set up expansion bus config to a really slow timing. + * The CF driver will dynamically reconfigure these timings + * depending on selected PIO mode (0-4). + */ + intel,ixp4xx-eb-t1 = <3>; // 3 cycles extra address phase + intel,ixp4xx-eb-t2 = <3>; // 3 cycles extra setup phase + intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase + intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase + intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase + intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type + intel,ixp4xx-eb-byte-access-on-halfword = <1>; + intel,ixp4xx-eb-mux-address-and-data = <0>; + intel,ixp4xx-eb-ahb-split-transfers = <0>; + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + /* First register set is CMD second is CTL */ + reg = <3 0xe00000 0x40000>, <3 0xe40000 0x40000>; + interrupt-parent = <&gpio0>; + interrupts = <12 IRQ_TYPE_EDGE_RISING>; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * In the boardfile for the Cambria from OpenWRT the interrupts + * are assigned one per IDSEL, so all 4 interrupts from IDSEL + * 1 are connected to IRQ 11, all 4 interrupts from IDSEL 2 + * connected to IRQ 10 etc. I find this highly unlikely so I + * have instead assumed that they are rotated (swizzled) like + * this with 11, 10, 9, 8 for the 4 pins on IDSEL 1 etc. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ + <0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ + <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ + <0x1000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */ + <0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ + <0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */ + <0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */ + <0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */ + /* IDSEL 4 */ + <0x2000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 8 */ + <0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */ + <0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */ + <0x2000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 9 */ + /* IDSEL 6 */ + <0x3000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 10 */ + <0x3000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 9 */ + <0x3000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 8 */ + <0x3000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 11 */ + /* IDSEL 15 */ + <0x7800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 8 */ + <0x7800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */ + <0x7800 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */ + <0x7800 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 3 is irq 9 */ + }; + + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + }; + }; + + ethernet@c800c000 { + status = "okay"; + queue-rx = <&qmgr 2>; + queue-txready = <&qmgr 19>; + phy-mode = "rgmii"; + phy-handle = <&phy2>; + intel,npe-handle = <&npe 0>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp43x-kixrp435.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-kixrp435.dts new file mode 100644 index 000000000000..4703a8b24765 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-kixrp435.dts @@ -0,0 +1,68 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Intel KIXRP435 Control Plane + * processor reference design. + */ + +/dts-v1/; + +#include "intel-ixp43x.dtsi" +#include "intel-ixp4xx-reference-design.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Intel KIXRP435 Reference Design"; + compatible = "intel,kixrp435", "intel,ixp43x"; + #address-cells = <1>; + #size-cells = <1>; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 16 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x0fe0000 */ + fis-index-block = <0x7f>; + }; + }; + }; + + /* CHECKME: ethernet set-up taken from Gateworks Cambria */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + }; + }; + + ethernet@c800c000 { + status = "okay"; + queue-rx = <&qmgr 2>; + queue-txready = <&qmgr 19>; + phy-mode = "rgmii"; + phy-handle = <&phy2>; + intel,npe-handle = <&npe 0>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp43x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp43x.dtsi new file mode 100644 index 000000000000..60bf9903e0f8 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Intel XScale Network Processors + * in the IXP 43x series. This series has 64 interrupts and adds a few more + * peripherals over the 42x series. + */ +#include "intel-ixp4xx.dtsi" + +/ { + soc { + bus@c4000000 { + compatible = "intel,ixp43x-expansion-bus-controller", "syscon"; + /* Uses at least up to 0x230 */ + reg = <0xc4000000 0x1000>; + }; + + pci@c0000000 { + compatible = "intel,ixp43x-pci"; + }; + + interrupt-controller@c8003000 { + compatible = "intel,ixp43x-interrupt"; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp45x-ixp46x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp45x-ixp46x.dtsi new file mode 100644 index 000000000000..1dd4a65cb7a6 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp45x-ixp46x.dtsi @@ -0,0 +1,86 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Intel XScale Network Processors + * in the IXP45x and IXP46x series. This series has 64 interrupts and adds a + * few more peripherals over the 42x and 43x series so this extends the + * basic IXP4xx DTSI. + */ +#include "intel-ixp4xx.dtsi" + +/ { + soc { + bus@c4000000 { + compatible = "intel,ixp46x-expansion-bus-controller", "syscon"; + /* Uses at least up to 0x124 */ + reg = <0xc4000000 0x1000>; + }; + + rng@70002100 { + compatible = "intel,ixp46x-rng"; + reg = <0x70002100 4>; + }; + + interrupt-controller@c8003000 { + compatible = "intel,ixp43x-interrupt"; + }; + + /* + * This is the USB Device Mode (UDC) controller, which is used + * to present the IXP4xx as a device on a USB bus. + */ + usb@c800b000 { + compatible = "intel,ixp4xx-udc"; + reg = <0xc800b000 0x1000>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + i2c@c8011000 { + compatible = "intel,ixp4xx-i2c"; + reg = <0xc8011000 0x18>; + interrupts = <33 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + /* This is known as EthB1 */ + ethernet@c800d000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc800d000 0x1000>; + status = "disabled"; + intel,npe = <1>; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 0>; + queue-txready = <&qmgr 0>; + }; + + /* This is known as EthB2 */ + ethernet@c800e000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc800e000 0x1000>; + status = "disabled"; + intel,npe = <2>; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 0>; + queue-txready = <&qmgr 0>; + }; + + /* This is known as EthB3 */ + ethernet@c800f000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc800f000 0x1000>; + status = "disabled"; + intel,npe = <3>; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 0>; + queue-txready = <&qmgr 0>; + }; + + ptp-timer@c8010000 { + compatible = "intel,ixp46x-ptp-timer"; + reg = <0xc8010000 0x1000>; + interrupt-parent = <&gpio0>; + interrupts = <8 IRQ_TYPE_EDGE_FALLING>, <7 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "master", "slave"; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp46x-ixdp465.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp46x-ixdp465.dts new file mode 100644 index 000000000000..a062cd1a6588 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp46x-ixdp465.dts @@ -0,0 +1,38 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Intel IXDP465 Control Plane processor reference + * design, codename "BMP". + */ + +/dts-v1/; + +#include "intel-ixp45x-ixp46x.dtsi" +#include "intel-ixp4xx-reference-design.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Intel IXDP465 BMP Reference Design"; + compatible = "intel,ixdp465", "intel,ixp46x"; + #address-cells = <1>; + #size-cells = <1>; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 32 MB of Flash mapped in at CS0 and CS1 */ + reg = <0 0x00000000 0x2000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x1fe0000 */ + fis-index-block = <0xff>; + }; + }; + }; + /* TODO: configure ethernet etc */ + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi new file mode 100644 index 000000000000..31c0a69771c4 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi @@ -0,0 +1,134 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree include file for Intel reference designs for the + * XScale Network Processors in the IXP 4xx series. Common device + * set-up for IXDP425, IXCDP1100, KIXRP435 and IXDP465. + */ + +/ { + memory@0 { + /* + * The board supports up to 256 MB of memory. Here we put in + * 64 MB and this may be modified by the boot loader. + */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@50 { + /* + * Philips PCF8582C-2T/03 512byte I2C EEPROM + * should behave like an Atmel 24c04. + */ + compatible = "atmel,24c04"; + reg = <0x50>; + pagesize = <16>; + size = <512>; + read-only; + }; + }; + + soc { + bus@c4000000 { + /* Flash memory defined per-variant */ + nand-controller@3,0 { + /* Some designs have a NAND on CS3 enable it here if present */ + status = "disabled"; + + /* + * gen_nand needs to be extended and documented to get + * command byte = 1 and address byte = 2 from the device + * tree. + */ + compatible = "gen_nand"; + + /* Expansion bus set-up */ + intel,ixp4xx-eb-t1 = <0>; + intel,ixp4xx-eb-t2 = <0>; + intel,ixp4xx-eb-t3 = <1>; // 1 cycle extra strobe phase + intel,ixp4xx-eb-t4 = <0>; + intel,ixp4xx-eb-t5 = <0>; + intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type + intel,ixp4xx-eb-byte-access-on-halfword = <0>; + intel,ixp4xx-eb-mux-address-and-data = <0>; + intel,ixp4xx-eb-ahb-split-transfers = <0>; + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + + /* 512 bytes memory window */ + reg = <3 0x00000000 0x200>; + nand-on-flash-bbt; + nand-ecc-mode = "soft_bch"; + nand-ecc-step-size = <512>; + nand-ecc-strength = <4>; + nce-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; /* NCE */ + + label = "ixp400 NAND"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + fs@0 { + label = "ixp400 NAND FS 0"; + reg = <0x0 0x800000>; + }; + fs@800000 { + label = "ixp400 NAND FS 1"; + reg = <0x800000 0x0>; + }; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from IXDP425 PCI boardfile. + * PCI slots on the BIXMB425BD base card. + * We have up to 4 slots (IDSEL) with 4 swizzled IRQs. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ + <0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ + <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ + <0x1000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */ + <0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ + <0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */ + <0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */ + <0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */ + /* IDSEL 4 */ + <0x2000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */ + <0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */ + <0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */ + <0x2000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */ + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp4xx.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx.dtsi new file mode 100644 index 000000000000..51a716c59669 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx.dtsi @@ -0,0 +1,202 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Intel XScale Network Processors + * in the IXP 4xx series. + */ +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> + +/ { + soc { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "simple-bus"; + interrupt-parent = <&intcon>; + + /* + * The IXP4xx expansion bus is a set of up to 7 each up to 16MB + * windows in the 256MB space from 0x50000000 to 0x5fffffff. + */ + bus@c4000000 { + /* compatible and reg filled in by per-soc device tree */ + native-endian; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0x0 0x50000000 0x01000000>, + <1 0x0 0x51000000 0x01000000>, + <2 0x0 0x52000000 0x01000000>, + <3 0x0 0x53000000 0x01000000>, + <4 0x0 0x54000000 0x01000000>, + <5 0x0 0x55000000 0x01000000>, + <6 0x0 0x56000000 0x01000000>, + <7 0x0 0x57000000 0x01000000>; + dma-ranges = <0 0x0 0x50000000 0x01000000>, + <1 0x0 0x51000000 0x01000000>, + <2 0x0 0x52000000 0x01000000>, + <3 0x0 0x53000000 0x01000000>, + <4 0x0 0x54000000 0x01000000>, + <5 0x0 0x55000000 0x01000000>, + <6 0x0 0x56000000 0x01000000>, + <7 0x0 0x57000000 0x01000000>; + }; + + qmgr: queue-manager@60000000 { + compatible = "intel,ixp4xx-ahb-queue-manager"; + reg = <0x60000000 0x4000>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>, <4 IRQ_TYPE_LEVEL_HIGH>; + }; + + pci@c0000000 { + /* compatible filled in by per-soc device tree */ + reg = <0xc0000000 0x1000>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, + <9 IRQ_TYPE_LEVEL_HIGH>, + <10 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + bus-range = <0x00 0xff>; + status = "disabled"; + + ranges = + /* + * 64MB 32bit non-prefetchable memory 0x48000000-0x4bffffff + * done in 4 chunks of 16MB each. + */ + <0x02000000 0 0x48000000 0x48000000 0 0x04000000>, + /* 64KB I/O space at 0x4c000000 */ + <0x01000000 0 0x00000000 0x4c000000 0 0x00010000>; + + /* + * This needs to map to the start of physical memory so + * PCI devices can see all (hopefully) memory. This is done + * using 4 1:1 16MB windows, so the RAM should not be more than + * 64 MB for this to work. If your memory is anywhere else + * than at 0x0 you need to alter this. + */ + dma-ranges = + <0x02000000 0 0x00000000 0x00000000 0 0x04000000>; + + /* Each unique DTS using PCI must specify the swizzling */ + }; + + uart0: serial@c8000000 { + compatible = "intel,xscale-uart"; + reg = <0xc8000000 0x1000>; + /* + * The reg-offset and reg-shift is a side effect + * of running the platform in big endian mode. + */ + reg-offset = <3>; + reg-shift = <2>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <14745600>; + no-loopback-test; + }; + + uart1: serial@c8001000 { + compatible = "intel,xscale-uart"; + reg = <0xc8001000 0x1000>; + /* + * The reg-offset and reg-shift is a side effect + * of running the platform in big endian mode. + */ + reg-offset = <3>; + reg-shift = <2>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <14745600>; + no-loopback-test; + }; + + gpio0: gpio@c8004000 { + compatible = "intel,ixp4xx-gpio"; + reg = <0xc8004000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + intcon: interrupt-controller@c8003000 { + /* + * Note: no compatible string. The subvariant of the + * chip needs to define what version it is. The + * location of the interrupt controller is fixed in + * memory across all variants. + */ + reg = <0xc8003000 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + timer@c8005000 { + compatible = "intel,ixp4xx-timer"; + reg = <0xc8005000 0x100>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + }; + + npe: npe@c8006000 { + compatible = "intel,ixp4xx-network-processing-engine"; + reg = <0xc8006000 0x1000>, <0xc8007000 0x1000>, <0xc8008000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + /* NPE-A contains two high-speed serial links */ + hss@0 { + compatible = "intel,ixp4xx-hss"; + reg = <0>; + intel,npe-handle = <&npe 0>; + status = "disabled"; + }; + + hss@1 { + compatible = "intel,ixp4xx-hss"; + reg = <1>; + intel,npe-handle = <&npe 0>; + status = "disabled"; + }; + + /* NPE-C contains a crypto accelerator */ + crypto { + compatible = "intel,ixp4xx-crypto"; + intel,npe-handle = <&npe 2>; + queue-rx = <&qmgr 30>; + queue-txready = <&qmgr 29>; + }; + }; + + /* This is known as EthB */ + ethernet@c8009000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc8009000 0x1000>; + status = "disabled"; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + intel,npe-handle = <&npe 1>; + }; + + /* This is known as EthC */ + ethernet@c800a000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc800a000 0x1000>; + status = "disabled"; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 0>; + queue-txready = <&qmgr 0>; + intel,npe-handle = <&npe 2>; + }; + + /* This is known as EthA */ + ethernet@c800c000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc800c000 0x1000>; + status = "disabled"; + intel,npe = <0>; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 0>; + queue-txready = <&qmgr 0>; + }; + }; +}; |