diff options
Diffstat (limited to 'arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts')
| -rw-r--r-- | arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts | 119 |
1 files changed, 1 insertions, 118 deletions
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts index cb8600d0ea1e..d6e732b12c52 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts @@ -5,95 +5,19 @@ /dts-v1/; -#include "sun50i-h616.dtsi" - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/leds/common.h> +#include "sun50i-h616-orangepi-zero.dtsi" / { model = "OrangePi Zero2"; compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616"; - - aliases { - ethernet0 = &emac0; - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - leds { - compatible = "gpio-leds"; - - led-0 { - function = LED_FUNCTION_POWER; - color = <LED_COLOR_ID_RED>; - gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */ - default-state = "on"; - }; - - led-1 { - function = LED_FUNCTION_STATUS; - color = <LED_COLOR_ID_GREEN>; - gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */ - }; - }; - - reg_vcc5v: vcc5v { - /* board wide 5V supply directly from the USB-C socket */ - compatible = "regulator-fixed"; - regulator-name = "vcc-5v"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - }; - - reg_usb1_vbus: regulator-usb1-vbus { - compatible = "regulator-fixed"; - regulator-name = "usb1-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - vin-supply = <®_vcc5v>; - enable-active-high; - gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */ - }; }; -&ehci1 { - status = "okay"; -}; - -/* USB 2 & 3 are on headers only. */ - &emac0 { - pinctrl-names = "default"; - pinctrl-0 = <&ext_rgmii_pins>; - phy-mode = "rgmii"; - phy-handle = <&ext_rgmii_phy>; phy-supply = <®_dcdce>; - allwinner,rx-delay-ps = <3100>; - allwinner,tx-delay-ps = <700>; - status = "okay"; -}; - -&mdio0 { - ext_rgmii_phy: ethernet-phy@1 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <1>; - }; }; &mmc0 { vmmc-supply = <®_dcdce>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ - bus-width = <4>; - status = "okay"; -}; - -&ohci1 { - status = "okay"; }; &r_rsb { @@ -211,44 +135,3 @@ vcc-ph-supply = <®_aldo1>; vcc-pi-supply = <®_aldo1>; }; - -&spi0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>; - - flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <40000000>; - }; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_ph_pins>; - status = "okay"; -}; - -&usbotg { - /* - * PHY0 pins are connected to a USB-C socket, but a role switch - * is not implemented: both CC pins are pulled to GND. - * The VBUS pins power the device, so a fixed peripheral mode - * is the best choice. - * The board can be powered via GPIOs, in this case port0 *can* - * act as a host (with a cable/adapter ignoring CC), as VBUS is - * then provided by the GPIOs. Any user of this setup would - * need to adjust the DT accordingly: dr_mode set to "host", - * enabling OHCI0 and EHCI0. - */ - dr_mode = "peripheral"; - status = "okay"; -}; - -&usbphy { - usb1_vbus-supply = <®_usb1_vbus>; - status = "okay"; -}; |