diff options
Diffstat (limited to 'arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi')
| -rw-r--r-- | arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi | 107 |
1 files changed, 72 insertions, 35 deletions
diff --git a/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi index acac4666ae59..39845faec894 100644 --- a/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi +++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi @@ -5,47 +5,26 @@ * Copyright (C) 2023 Renesas Electronics Corp. */ +#include <dt-bindings/clock/renesas,r9a08g045-vbattb.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/pinctrl/rzg2l-pinctrl.h> -/* - * On-board switches' states: - * @SW_OFF: switch's state is OFF - * @SW_ON: switch's state is ON - */ -#define SW_OFF 0 -#define SW_ON 1 - -/* - * SW_CONFIG[x] switches' states: - * @SW_CONFIG2: - * SW_OFF - SD0 is connected to eMMC - * SW_ON - SD0 is connected to uSD0 card - * @SW_CONFIG3: - * SW_OFF - SD2 is connected to SoC - * SW_ON - SCIF1, SSI0, IRQ0, IRQ1 connected to SoC - */ -#define SW_CONFIG2 SW_ON -#define SW_CONFIG3 SW_ON +#include "rzg3s-smarc-switches.h" / { compatible = "renesas,rzg3s-smarcm", "renesas,r9a08g045s33", "renesas,r9a08g045"; aliases { + i2c1 = &i2c1; mmc0 = &sdhi0; #if SW_CONFIG3 == SW_OFF mmc2 = &sdhi2; #else - eth0 = ð0; - eth1 = ð1; + ethernet0 = ð0; + ethernet1 = ð1; #endif }; - chosen { - bootargs = "ignore_loglevel"; - stdout-path = "serial0:115200n8"; - }; - memory@48000000 { device_type = "memory"; /* First 128MB is reserved for secure area. */ @@ -61,7 +40,6 @@ enable-active-high; }; -#if SW_CONFIG2 == SW_ON vccq_sdhi0: regulator1 { compatible = "regulator-gpio"; regulator-name = "SDHI0 VccQ"; @@ -71,8 +49,8 @@ gpios-states = <1>; states = <3300000 1>, <1800000 0>; }; -#else - reg_1p8v: regulator1 { + + reg_1p8v: regulator2 { compatible = "regulator-fixed"; regulator-name = "fixed-1.8V"; regulator-min-microvolt = <1800000>; @@ -80,9 +58,17 @@ regulator-boot-on; regulator-always-on; }; -#endif - vcc_sdhi2: regulator2 { + reg_3p3v: regulator3 { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vcc_sdhi2: regulator4 { compatible = "regulator-fixed"; regulator-name = "SDHI2 Vcc"; regulator-min-microvolt = <3300000>; @@ -90,6 +76,16 @@ gpios = <&pinctrl RZG2L_GPIO(8, 1) GPIO_ACTIVE_HIGH>; enable-active-high; }; + + x3_clk: x3-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + }; +}; + +&adc { + status = "okay"; }; #if SW_CONFIG3 == SW_ON @@ -102,8 +98,7 @@ phy0: ethernet-phy@7 { reg = <7>; - interrupt-parent = <&pinctrl>; - interrupts = <RZG2L_GPIO(12, 0) IRQ_TYPE_EDGE_FALLING>; + interrupts-extended = <&pinctrl RZG2L_GPIO(12, 0) IRQ_TYPE_EDGE_FALLING>; rxc-skew-psec = <0>; txc-skew-psec = <0>; rxdv-skew-psec = <0>; @@ -128,8 +123,7 @@ phy1: ethernet-phy@7 { reg = <7>; - interrupt-parent = <&pinctrl>; - interrupts = <RZG2L_GPIO(12, 1) IRQ_TYPE_EDGE_FALLING>; + interrupts-extended = <&pinctrl RZG2L_GPIO(12, 1) IRQ_TYPE_EDGE_FALLING>; rxc-skew-psec = <0>; txc-skew-psec = <0>; rxdv-skew-psec = <0>; @@ -150,6 +144,34 @@ clock-frequency = <24000000>; }; +&i2c1 { + status = "okay"; + + versa3: clock-generator@68 { + compatible = "renesas,5l35023"; + reg = <0x68>; + clocks = <&x3_clk>; + #clock-cells = <1>; + assigned-clocks = <&versa3 0>, + <&versa3 1>, + <&versa3 2>, + <&versa3 3>, + <&versa3 4>, + <&versa3 5>; + assigned-clock-rates = <24000000>, + <12288000>, + <11289600>, + <25000000>, + <100000000>, + <100000000>; + renesas,settings = [ + 80 00 11 19 4c 42 dc 2f 06 7d 20 1a 5f 1e f2 27 + 00 40 00 00 00 00 00 00 06 0c 19 02 3f f0 90 86 + a0 80 30 30 9c + ]; + }; +}; + #if SW_CONFIG2 == SW_ON /* SD0 slot */ &sdhi0 { @@ -341,6 +363,21 @@ }; }; +&rtc { + status = "okay"; +}; + +&vbattb { + assigned-clocks = <&vbattb VBATTB_MUX>; + assigned-clock-parents = <&vbattb VBATTB_XC>; + quartz-load-femtofarads = <12500>; + status = "okay"; +}; + +&vbattb_xtal { + clock-frequency = <32768>; +}; + &wdt0 { timeout-sec = <60>; status = "okay"; |