diff options
Diffstat (limited to 'drivers/ata/Kconfig')
| -rw-r--r-- | drivers/ata/Kconfig | 181 |
1 files changed, 91 insertions, 90 deletions
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig index 030cb32da980..120a2b7067fc 100644 --- a/drivers/ata/Kconfig +++ b/drivers/ata/Kconfig @@ -116,23 +116,40 @@ config SATA_AHCI If unsure, say N. config SATA_MOBILE_LPM_POLICY - int "Default SATA Link Power Management policy for mobile chipsets" - range 0 4 - default 0 + int "Default SATA Link Power Management policy" + range 0 5 + default 3 depends on SATA_AHCI help Select the Default SATA Link Power Management (LPM) policy to use - for mobile / laptop variants of chipsets / "South Bridges". - - The value set has the following meanings: + for chipsets / "South Bridges" supporting low-power modes. Such + chipsets are ubiquitous across laptops, desktops and servers. + Each policy combines power saving states and features: + - Partial: The Phy logic is powered but is in a reduced power + state. The exit latency from this state is no longer than + 10us). + - Slumber: The Phy logic is powered but is in an even lower power + state. The exit latency from this state is potentially + longer, but no longer than 10ms. + - DevSleep: The Phy logic may be powered down. The exit latency from + this state is no longer than 20 ms, unless otherwise + specified by DETO in the device Identify Device Data log. + - HIPM: Host Initiated Power Management (host automatically + transitions to partial and slumber). + - DIPM: Device Initiated Power Management (device automatically + transitions to partial and slumber). + + The possible values for the default SATA link power management + policies are: 0 => Keep firmware settings - 1 => Maximum performance - 2 => Medium power - 3 => Medium power with Device Initiated PM enabled - 4 => Minimum power + 1 => No power savings (maximum performance) + 2 => HIPM (Partial) + 3 => HIPM (Partial) and DIPM (Partial and Slumber) + 4 => HIPM (Partial and DevSleep) and DIPM (Partial and Slumber) + 5 => HIPM (Slumber and DevSleep) and DIPM (Partial and Slumber) - Note "Minimum power" is known to cause issues, including disk - corruption, with some disks and should not be used. + Excluding the value 0, higher values represent policies with higher + power savings. config SATA_AHCI_PLATFORM tristate "Platform AHCI SATA support" @@ -146,7 +163,7 @@ config SATA_AHCI_PLATFORM config AHCI_BRCM tristate "Broadcom AHCI SATA support" depends on ARCH_BRCMSTB || BMIPS_GENERIC || ARCH_BCM_NSP || \ - ARCH_BCM_63XX + ARCH_BCMBCA || COMPILE_TEST select SATA_HOST help This option enables support for the AHCI SATA3 controller found on @@ -156,7 +173,7 @@ config AHCI_BRCM config AHCI_DA850 tristate "DaVinci DA850 AHCI SATA support" - depends on ARCH_DAVINCI_DA850 + depends on ARCH_DAVINCI_DA850 || COMPILE_TEST select SATA_HOST help This option enables support for the DaVinci DA850 SoC's @@ -166,7 +183,7 @@ config AHCI_DA850 config AHCI_DM816 tristate "DaVinci DM816 AHCI SATA support" - depends on ARCH_OMAP2PLUS + depends on ARCH_OMAP2PLUS || COMPILE_TEST select SATA_HOST help This option enables support for the DaVinci DM816 SoC's @@ -174,9 +191,19 @@ config AHCI_DM816 If unsure, say N. +config AHCI_DWC + tristate "Synopsys DWC AHCI SATA support" + select SATA_HOST + select MFD_SYSCON if (MIPS_BAIKAL_T1 || COMPILE_TEST) + help + This option enables support for the Synopsys DWC AHCI SATA + controller implementation. + + If unsure, say N. + config AHCI_ST tristate "ST AHCI SATA support" - depends on ARCH_STI + depends on ARCH_STI || COMPILE_TEST select SATA_HOST help This option enables support for ST AHCI SATA controller. @@ -206,7 +233,7 @@ config AHCI_CEVA config AHCI_MTK tristate "MediaTek AHCI SATA support" - depends on ARCH_MEDIATEK + depends on ARCH_MEDIATEK || COMPILE_TEST select MFD_SYSCON select SATA_HOST help @@ -217,7 +244,7 @@ config AHCI_MTK config AHCI_MVEBU tristate "Marvell EBU AHCI SATA support" - depends on ARCH_MVEBU + depends on ARCH_MVEBU || COMPILE_TEST select SATA_HOST help This option enables support for the Marvebu EBU SoC's @@ -236,7 +263,7 @@ config AHCI_OCTEON config AHCI_SUNXI tristate "Allwinner sunxi AHCI SATA support" - depends on ARCH_SUNXI + depends on ARCH_SUNXI || COMPILE_TEST select SATA_HOST help This option enables support for the Allwinner sunxi SoC's @@ -246,7 +273,7 @@ config AHCI_SUNXI config AHCI_TEGRA tristate "NVIDIA Tegra AHCI SATA support" - depends on ARCH_TEGRA + depends on ARCH_TEGRA || COMPILE_TEST select SATA_HOST help This option enables support for the NVIDIA Tegra SoC's @@ -256,7 +283,7 @@ config AHCI_TEGRA config AHCI_XGENE tristate "APM X-Gene 6.0Gbps AHCI SATA host controller support" - depends on PHY_XGENE + depends on PHY_XGENE || COMPILE_TEST select SATA_HOST help This option enables support for APM X-Gene SoC SATA host controller. @@ -264,6 +291,7 @@ config AHCI_XGENE config AHCI_QORIQ tristate "Freescale QorIQ AHCI SATA support" depends on OF + depends on SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST select SATA_HOST help This option enables support for the Freescale QorIQ AHCI SoC's @@ -273,7 +301,7 @@ config AHCI_QORIQ config SATA_FSL tristate "Freescale 3.0Gbps SATA support" - depends on FSL_SOC + depends on FSL_SOC || COMPILE_TEST select SATA_HOST help This option enables support for Freescale 3.0Gbps SATA controller. @@ -294,7 +322,7 @@ config SATA_GEMINI config SATA_AHCI_SEATTLE tristate "AMD Seattle 6.0Gbps AHCI SATA host controller support" - depends on ARCH_SEATTLE + depends on ARCH_SEATTLE || COMPILE_TEST select SATA_HOST help This option enables support for AMD Seattle SATA host controller. @@ -432,18 +460,6 @@ config SATA_DWC_OLD_DMA This option enables support for old device trees without the "dmas" property. -config SATA_DWC_DEBUG - bool "Debugging driver version" - depends on SATA_DWC - help - This option enables debugging output in the driver. - -config SATA_DWC_VDEBUG - bool "Verbose debug output" - depends on SATA_DWC_DEBUG - help - This option enables the taskfile dumping and NCQ debugging. - config SATA_HIGHBANK tristate "Calxeda Highbank SATA support" depends on ARCH_HIGHBANK || COMPILE_TEST @@ -556,7 +572,7 @@ comment "PATA SFF controllers with BMDMA" config PATA_ALI tristate "ALi PATA support" - depends on PCI + depends on PCI && HAS_IOPORT select PATA_TIMINGS help This option enables support for the ALi ATA interfaces @@ -566,7 +582,7 @@ config PATA_ALI config PATA_AMD tristate "AMD/NVidia PATA support" - depends on PCI + depends on PCI && HAS_IOPORT select PATA_TIMINGS help This option enables support for the AMD and NVidia PATA @@ -584,7 +600,7 @@ config PATA_ARASAN_CF config PATA_ARTOP tristate "ARTOP 6210/6260 PATA support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for ARTOP PATA controllers. @@ -609,19 +625,9 @@ config PATA_ATP867X If unsure, say N. -config PATA_BK3710 - tristate "Palmchip BK3710 PATA support" - depends on ARCH_DAVINCI - select PATA_TIMINGS - help - This option enables support for the integrated IDE controller on - the TI DaVinci SoC. - - If unsure, say N. - config PATA_CMD64X tristate "CMD64x PATA support" - depends on PCI + depends on PCI && HAS_IOPORT select PATA_TIMINGS help This option enables support for the CMD64x series chips @@ -649,7 +655,8 @@ config PATA_CS5530 config PATA_CS5535 tristate "CS5535 PATA support (Experimental)" - depends on PCI && X86_32 + depends on PCI && (X86_32 || (X86_64 && COMPILE_TEST)) + depends on !UML help This option enables support for the NatSemi/AMD CS5535 companion chip used with the Geode processor family. @@ -667,7 +674,7 @@ config PATA_CS5536 config PATA_CYPRESS tristate "Cypress CY82C693 PATA support (Very Experimental)" - depends on PCI + depends on PCI && HAS_IOPORT select PATA_TIMINGS help This option enables support for the Cypress/Contaq CY82C693 @@ -696,8 +703,7 @@ config PATA_EP93XX config PATA_FTIDE010 tristate "Faraday Technology FTIDE010 PATA support" - depends on OF - depends on ARM + depends on ARM || COMPILE_TEST depends on SATA_GEMINI help This option enables support for the Faraday FTIDE010 @@ -716,7 +722,7 @@ config PATA_HPT366 config PATA_HPT37X tristate "HPT 370/370A/371/372/374/302 PATA support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for the majority of the later HPT PATA controllers via the new ATA layer. @@ -725,7 +731,7 @@ config PATA_HPT37X config PATA_HPT3X2N tristate "HPT 371N/372N/302N PATA support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for the N variant HPT PATA controllers via the new ATA layer. @@ -760,7 +766,7 @@ config PATA_ICSIDE config PATA_IMX tristate "PATA support for Freescale iMX" - depends on ARCH_MXC + depends on ARCH_MXC || COMPILE_TEST select PATA_TIMINGS help This option enables support for the PATA host available on Freescale @@ -828,7 +834,7 @@ config PATA_MPC52xx config PATA_NETCELL tristate "NETCELL Revolution RAID support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for the Netcell Revolution RAID PATA controller. @@ -864,7 +870,7 @@ config PATA_OLDPIIX config PATA_OPTIDMA tristate "OPTI FireStar PATA support (Very Experimental)" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables DMA/PIO support for the later OPTi controllers found on some old motherboards and in some @@ -874,7 +880,7 @@ config PATA_OPTIDMA config PATA_PDC2027X tristate "Promise PATA 2027x support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for Promise PATA pdc20268 to pdc20277 host adapters. @@ -882,7 +888,7 @@ config PATA_PDC2027X config PATA_PDC_OLD tristate "Older Promise PATA controller support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for the Promise 20246, 20262, 20263, 20265 and 20267 adapters. @@ -910,7 +916,7 @@ config PATA_RDC config PATA_SC1200 tristate "SC1200 PATA support" - depends on PCI && (X86_32 || COMPILE_TEST) + depends on PCI && (X86_32 || COMPILE_TEST) && HAS_IOPORT help This option enables support for the NatSemi/AMD SC1200 SoC companion chip used with the Geode processor family. @@ -928,7 +934,7 @@ config PATA_SCH config PATA_SERVERWORKS tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for the Serverworks OSB4/CSB5/CSB6 and HT1000 PATA controllers, via the new ATA layer. @@ -981,7 +987,7 @@ config PATA_VIA config PATA_PXA tristate "PXA DMA-capable PATA support" - depends on ARCH_PXA + depends on ARCH_PXA || COMPILE_TEST help This option enables support for harddrive attached to PXA CPU's bus. @@ -1015,11 +1021,11 @@ config PATA_CMD640_PCI If unsure, say N. config PATA_FALCON - tristate "Atari Falcon PATA support" - depends on M68K && ATARI + tristate "Atari Falcon and Q40/Q60 PATA support" + depends on M68K && (ATARI || Q40) help This option enables support for the on-board IDE - interface on the Atari Falcon. + interface on the Atari Falcon and Q40/Q60. If unsure, say N. @@ -1058,7 +1064,7 @@ config PATA_ISAPNP config PATA_IXP4XX_CF tristate "IXP4XX Compact Flash support" - depends on ARCH_IXP4XX + depends on ARCH_IXP4XX || COMPILE_TEST help This option enables support for a Compact Flash connected on the ixp4xx expansion bus. This driver had been written for @@ -1093,15 +1099,6 @@ config PATA_OPTI If unsure, say N. -config PATA_PALMLD - tristate "Palm LifeDrive PATA support" - depends on MACH_PALMLD - help - This option enables support for Palm LifeDrive's internal ATA - port via the new ATA layer. - - If unsure, say N. - config PATA_PCMCIA tristate "PCMCIA PATA support" depends on PCMCIA @@ -1112,8 +1109,7 @@ config PATA_PCMCIA If unsure, say N. config PATA_PLATFORM - tristate "Generic platform device PATA support" - depends on EXPERT || PPC || HAVE_PATA_PLATFORM + tristate "Generic platform device PATA support" if HAVE_PATA_PLATFORM help This option enables support for generic directly connected ATA devices commonly found on embedded systems. @@ -1122,7 +1118,8 @@ config PATA_PLATFORM config PATA_OF_PLATFORM tristate "OpenFirmware platform device PATA support" - depends on PATA_PLATFORM && OF + depends on OF + select PATA_PLATFORM help This option enables support for generic directly connected ATA devices commonly found on embedded systems with OpenFirmware @@ -1155,16 +1152,6 @@ config PATA_RZ1000 If unsure, say N. -config PATA_SAMSUNG_CF - tristate "Samsung SoC PATA support" - depends on SAMSUNG_DEV_IDE - select PATA_TIMINGS - help - This option enables basic support for Samsung's S3C/S5P board - PATA controllers via the new ATA layer - - If unsure, say N. - config PATA_WINBOND_VLB tristate "Winbond W83759A VLB PATA support (Experimental)" depends on ISA @@ -1173,6 +1160,20 @@ config PATA_WINBOND_VLB Support for the Winbond W83759A controller on Vesa Local Bus systems. +config PATA_PARPORT + tristate "Parallel port IDE device support" + depends on PARPORT_PC + help + There are many external CD-ROM and disk devices that connect through + your computer's parallel port. Most of them are actually IDE devices + using a parallel port IDE adapter. This option enables the + PATA_PARPORT subsystem which contains drivers for many of these + external drives. + Read <file:Documentation/admin-guide/blockdev/paride.rst> for more + information. + +source "drivers/ata/pata_parport/Kconfig" + comment "Generic fallback / legacy drivers" config PATA_ACPI @@ -1197,7 +1198,7 @@ config ATA_GENERIC config PATA_LEGACY tristate "Legacy ISA PATA support (Experimental)" - depends on (ISA || PCI) + depends on (ISA || PCI) && HAS_IOPORT select PATA_TIMINGS help This option enables support for ISA/VLB/PCI bus legacy PATA |