diff options
Diffstat (limited to 'drivers/ata/Kconfig')
| -rw-r--r-- | drivers/ata/Kconfig | 117 |
1 files changed, 59 insertions, 58 deletions
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig index 36833a862998..120a2b7067fc 100644 --- a/drivers/ata/Kconfig +++ b/drivers/ata/Kconfig @@ -116,25 +116,40 @@ config SATA_AHCI If unsure, say N. config SATA_MOBILE_LPM_POLICY - int "Default SATA Link Power Management policy for low power chipsets" - range 0 4 - default 0 + int "Default SATA Link Power Management policy" + range 0 5 + default 3 depends on SATA_AHCI help Select the Default SATA Link Power Management (LPM) policy to use for chipsets / "South Bridges" supporting low-power modes. Such - chipsets are typically found on most laptops but desktops and - servers now also widely use chipsets supporting low power modes. - - The value set has the following meanings: + chipsets are ubiquitous across laptops, desktops and servers. + Each policy combines power saving states and features: + - Partial: The Phy logic is powered but is in a reduced power + state. The exit latency from this state is no longer than + 10us). + - Slumber: The Phy logic is powered but is in an even lower power + state. The exit latency from this state is potentially + longer, but no longer than 10ms. + - DevSleep: The Phy logic may be powered down. The exit latency from + this state is no longer than 20 ms, unless otherwise + specified by DETO in the device Identify Device Data log. + - HIPM: Host Initiated Power Management (host automatically + transitions to partial and slumber). + - DIPM: Device Initiated Power Management (device automatically + transitions to partial and slumber). + + The possible values for the default SATA link power management + policies are: 0 => Keep firmware settings - 1 => Maximum performance - 2 => Medium power - 3 => Medium power with Device Initiated PM enabled - 4 => Minimum power + 1 => No power savings (maximum performance) + 2 => HIPM (Partial) + 3 => HIPM (Partial) and DIPM (Partial and Slumber) + 4 => HIPM (Partial and DevSleep) and DIPM (Partial and Slumber) + 5 => HIPM (Slumber and DevSleep) and DIPM (Partial and Slumber) - Note "Minimum power" is known to cause issues, including disk - corruption, with some disks and should not be used. + Excluding the value 0, higher values represent policies with higher + power savings. config SATA_AHCI_PLATFORM tristate "Platform AHCI SATA support" @@ -276,6 +291,7 @@ config AHCI_XGENE config AHCI_QORIQ tristate "Freescale QorIQ AHCI SATA support" depends on OF + depends on SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST select SATA_HOST help This option enables support for the Freescale QorIQ AHCI SoC's @@ -295,7 +311,7 @@ config SATA_FSL config SATA_GEMINI tristate "Gemini SATA bridge support" - depends on ARCH_GEMINI || (OF && COMPILE_TEST) + depends on ARCH_GEMINI || COMPILE_TEST select SATA_HOST default ARCH_GEMINI help @@ -556,7 +572,7 @@ comment "PATA SFF controllers with BMDMA" config PATA_ALI tristate "ALi PATA support" - depends on PCI + depends on PCI && HAS_IOPORT select PATA_TIMINGS help This option enables support for the ALi ATA interfaces @@ -566,7 +582,7 @@ config PATA_ALI config PATA_AMD tristate "AMD/NVidia PATA support" - depends on PCI + depends on PCI && HAS_IOPORT select PATA_TIMINGS help This option enables support for the AMD and NVidia PATA @@ -584,7 +600,7 @@ config PATA_ARASAN_CF config PATA_ARTOP tristate "ARTOP 6210/6260 PATA support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for ARTOP PATA controllers. @@ -609,19 +625,9 @@ config PATA_ATP867X If unsure, say N. -config PATA_BK3710 - tristate "Palmchip BK3710 PATA support" - depends on ARCH_DAVINCI || COMPILE_TEST - select PATA_TIMINGS - help - This option enables support for the integrated IDE controller on - the TI DaVinci SoC. - - If unsure, say N. - config PATA_CMD64X tristate "CMD64x PATA support" - depends on PCI + depends on PCI && HAS_IOPORT select PATA_TIMINGS help This option enables support for the CMD64x series chips @@ -650,6 +656,7 @@ config PATA_CS5530 config PATA_CS5535 tristate "CS5535 PATA support (Experimental)" depends on PCI && (X86_32 || (X86_64 && COMPILE_TEST)) + depends on !UML help This option enables support for the NatSemi/AMD CS5535 companion chip used with the Geode processor family. @@ -667,7 +674,7 @@ config PATA_CS5536 config PATA_CYPRESS tristate "Cypress CY82C693 PATA support (Very Experimental)" - depends on PCI + depends on PCI && HAS_IOPORT select PATA_TIMINGS help This option enables support for the Cypress/Contaq CY82C693 @@ -696,7 +703,6 @@ config PATA_EP93XX config PATA_FTIDE010 tristate "Faraday Technology FTIDE010 PATA support" - depends on OF depends on ARM || COMPILE_TEST depends on SATA_GEMINI help @@ -716,7 +722,7 @@ config PATA_HPT366 config PATA_HPT37X tristate "HPT 370/370A/371/372/374/302 PATA support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for the majority of the later HPT PATA controllers via the new ATA layer. @@ -725,7 +731,7 @@ config PATA_HPT37X config PATA_HPT3X2N tristate "HPT 371N/372N/302N PATA support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for the N variant HPT PATA controllers via the new ATA layer. @@ -828,7 +834,7 @@ config PATA_MPC52xx config PATA_NETCELL tristate "NETCELL Revolution RAID support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for the Netcell Revolution RAID PATA controller. @@ -864,7 +870,7 @@ config PATA_OLDPIIX config PATA_OPTIDMA tristate "OPTI FireStar PATA support (Very Experimental)" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables DMA/PIO support for the later OPTi controllers found on some old motherboards and in some @@ -874,7 +880,7 @@ config PATA_OPTIDMA config PATA_PDC2027X tristate "Promise PATA 2027x support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for Promise PATA pdc20268 to pdc20277 host adapters. @@ -882,7 +888,7 @@ config PATA_PDC2027X config PATA_PDC_OLD tristate "Older Promise PATA controller support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for the Promise 20246, 20262, 20263, 20265 and 20267 adapters. @@ -910,7 +916,7 @@ config PATA_RDC config PATA_SC1200 tristate "SC1200 PATA support" - depends on PCI && (X86_32 || COMPILE_TEST) + depends on PCI && (X86_32 || COMPILE_TEST) && HAS_IOPORT help This option enables support for the NatSemi/AMD SC1200 SoC companion chip used with the Geode processor family. @@ -928,7 +934,7 @@ config PATA_SCH config PATA_SERVERWORKS tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support" - depends on PCI + depends on PCI && HAS_IOPORT help This option enables support for the Serverworks OSB4/CSB5/CSB6 and HT1000 PATA controllers, via the new ATA layer. @@ -1093,15 +1099,6 @@ config PATA_OPTI If unsure, say N. -config PATA_PALMLD - tristate "Palm LifeDrive PATA support" - depends on MACH_PALMLD - help - This option enables support for Palm LifeDrive's internal ATA - port via the new ATA layer. - - If unsure, say N. - config PATA_PCMCIA tristate "PCMCIA PATA support" depends on PCMCIA @@ -1155,16 +1152,6 @@ config PATA_RZ1000 If unsure, say N. -config PATA_SAMSUNG_CF - tristate "Samsung SoC PATA support" - depends on SAMSUNG_DEV_IDE || COMPILE_TEST - select PATA_TIMINGS - help - This option enables basic support for Samsung's S3C/S5P board - PATA controllers via the new ATA layer - - If unsure, say N. - config PATA_WINBOND_VLB tristate "Winbond W83759A VLB PATA support (Experimental)" depends on ISA @@ -1173,6 +1160,20 @@ config PATA_WINBOND_VLB Support for the Winbond W83759A controller on Vesa Local Bus systems. +config PATA_PARPORT + tristate "Parallel port IDE device support" + depends on PARPORT_PC + help + There are many external CD-ROM and disk devices that connect through + your computer's parallel port. Most of them are actually IDE devices + using a parallel port IDE adapter. This option enables the + PATA_PARPORT subsystem which contains drivers for many of these + external drives. + Read <file:Documentation/admin-guide/blockdev/paride.rst> for more + information. + +source "drivers/ata/pata_parport/Kconfig" + comment "Generic fallback / legacy drivers" config PATA_ACPI @@ -1197,7 +1198,7 @@ config ATA_GENERIC config PATA_LEGACY tristate "Legacy ISA PATA support (Experimental)" - depends on (ISA || PCI) + depends on (ISA || PCI) && HAS_IOPORT select PATA_TIMINGS help This option enables support for ISA/VLB/PCI bus legacy PATA |