summaryrefslogtreecommitdiff
path: root/drivers/ide/it821x.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ide/it821x.c')
-rw-r--r--drivers/ide/it821x.c715
1 files changed, 0 insertions, 715 deletions
diff --git a/drivers/ide/it821x.c b/drivers/ide/it821x.c
deleted file mode 100644
index 36a64c8ea575..000000000000
--- a/drivers/ide/it821x.c
+++ /dev/null
@@ -1,715 +0,0 @@
-/*
- * Copyright (C) 2004 Red Hat
- * Copyright (C) 2007 Bartlomiej Zolnierkiewicz
- *
- * May be copied or modified under the terms of the GNU General Public License
- * Based in part on the ITE vendor provided SCSI driver.
- *
- * Documentation:
- * Datasheet is freely available, some other documents under NDA.
- *
- * The ITE8212 isn't exactly a standard IDE controller. It has two
- * modes. In pass through mode then it is an IDE controller. In its smart
- * mode its actually quite a capable hardware raid controller disguised
- * as an IDE controller. Smart mode only understands DMA read/write and
- * identify, none of the fancier commands apply. The IT8211 is identical
- * in other respects but lacks the raid mode.
- *
- * Errata:
- * o Rev 0x10 also requires master/slave hold the same DMA timings and
- * cannot do ATAPI MWDMA.
- * o The identify data for raid volumes lacks CHS info (technically ok)
- * but also fails to set the LBA28 and other bits. We fix these in
- * the IDE probe quirk code.
- * o If you write LBA48 sized I/O's (ie > 256 sector) in smart mode
- * raid then the controller firmware dies
- * o Smart mode without RAID doesn't clear all the necessary identify
- * bits to reduce the command set to the one used
- *
- * This has a few impacts on the driver
- * - In pass through mode we do all the work you would expect
- * - In smart mode the clocking set up is done by the controller generally
- * but we must watch the other limits and filter.
- * - There are a few extra vendor commands that actually talk to the
- * controller but only work PIO with no IRQ.
- *
- * Vendor areas of the identify block in smart mode are used for the
- * timing and policy set up. Each HDD in raid mode also has a serial
- * block on the disk. The hardware extra commands are get/set chip status,
- * rebuild, get rebuild status.
- *
- * In Linux the driver supports pass through mode as if the device was
- * just another IDE controller. If the smart mode is running then
- * volumes are managed by the controller firmware and each IDE "disk"
- * is a raid volume. Even more cute - the controller can do automated
- * hotplug and rebuild.
- *
- * The pass through controller itself is a little demented. It has a
- * flaw that it has a single set of PIO/MWDMA timings per channel so
- * non UDMA devices restrict each others performance. It also has a
- * single clock source per channel so mixed UDMA100/133 performance
- * isn't perfect and we have to pick a clock. Thankfully none of this
- * matters in smart mode. ATAPI DMA is not currently supported.
- *
- * It seems the smart mode is a win for RAID1/RAID10 but otherwise not.
- *
- * TODO
- * - ATAPI UDMA is ok but not MWDMA it seems
- * - RAID configuration ioctls
- * - Move to libata once it grows up
- */
-
-#include <linux/types.h>
-#include <linux/module.h>
-#include <linux/slab.h>
-#include <linux/pci.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#define DRV_NAME "it821x"
-
-#define QUIRK_VORTEX86 1
-
-struct it821x_dev
-{
- unsigned int smart:1, /* Are we in smart raid mode */
- timing10:1; /* Rev 0x10 */
- u8 clock_mode; /* 0, ATA_50 or ATA_66 */
- u8 want[2][2]; /* Mode/Pri log for master slave */
- /* We need these for switching the clock when DMA goes on/off
- The high byte is the 66Mhz timing */
- u16 pio[2]; /* Cached PIO values */
- u16 mwdma[2]; /* Cached MWDMA values */
- u16 udma[2]; /* Cached UDMA values (per drive) */
- u16 quirks;
-};
-
-#define ATA_66 0
-#define ATA_50 1
-#define ATA_ANY 2
-
-#define UDMA_OFF 0
-#define MWDMA_OFF 0
-
-/*
- * We allow users to force the card into non raid mode without
- * flashing the alternative BIOS. This is also necessary right now
- * for embedded platforms that cannot run a PC BIOS but are using this
- * device.
- */
-
-static int it8212_noraid;
-
-/**
- * it821x_program - program the PIO/MWDMA registers
- * @drive: drive to tune
- * @timing: timing info
- *
- * Program the PIO/MWDMA timing for this channel according to the
- * current clock.
- */
-
-static void it821x_program(ide_drive_t *drive, u16 timing)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- int channel = hwif->channel;
- u8 conf;
-
- /* Program PIO/MWDMA timing bits */
- if(itdev->clock_mode == ATA_66)
- conf = timing >> 8;
- else
- conf = timing & 0xFF;
-
- pci_write_config_byte(dev, 0x54 + 4 * channel, conf);
-}
-
-/**
- * it821x_program_udma - program the UDMA registers
- * @drive: drive to tune
- * @timing: timing info
- *
- * Program the UDMA timing for this drive according to the
- * current clock.
- */
-
-static void it821x_program_udma(ide_drive_t *drive, u16 timing)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- int channel = hwif->channel;
- u8 unit = drive->dn & 1, conf;
-
- /* Program UDMA timing bits */
- if(itdev->clock_mode == ATA_66)
- conf = timing >> 8;
- else
- conf = timing & 0xFF;
-
- if (itdev->timing10 == 0)
- pci_write_config_byte(dev, 0x56 + 4 * channel + unit, conf);
- else {
- pci_write_config_byte(dev, 0x56 + 4 * channel, conf);
- pci_write_config_byte(dev, 0x56 + 4 * channel + 1, conf);
- }
-}
-
-/**
- * it821x_clock_strategy
- * @drive: drive to set up
- *
- * Select between the 50 and 66Mhz base clocks to get the best
- * results for this interface.
- */
-
-static void it821x_clock_strategy(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- ide_drive_t *pair = ide_get_pair_dev(drive);
- int clock, altclock, sel = 0;
- u8 unit = drive->dn & 1, v;
-
- if(itdev->want[0][0] > itdev->want[1][0]) {
- clock = itdev->want[0][1];
- altclock = itdev->want[1][1];
- } else {
- clock = itdev->want[1][1];
- altclock = itdev->want[0][1];
- }
-
- /*
- * if both clocks can be used for the mode with the higher priority
- * use the clock needed by the mode with the lower priority
- */
- if (clock == ATA_ANY)
- clock = altclock;
-
- /* Nobody cares - keep the same clock */
- if(clock == ATA_ANY)
- return;
- /* No change */
- if(clock == itdev->clock_mode)
- return;
-
- /* Load this into the controller ? */
- if(clock == ATA_66)
- itdev->clock_mode = ATA_66;
- else {
- itdev->clock_mode = ATA_50;
- sel = 1;
- }
-
- pci_read_config_byte(dev, 0x50, &v);
- v &= ~(1 << (1 + hwif->channel));
- v |= sel << (1 + hwif->channel);
- pci_write_config_byte(dev, 0x50, v);
-
- /*
- * Reprogram the UDMA/PIO of the pair drive for the switch
- * MWDMA will be dealt with by the dma switcher
- */
- if(pair && itdev->udma[1-unit] != UDMA_OFF) {
- it821x_program_udma(pair, itdev->udma[1-unit]);
- it821x_program(pair, itdev->pio[1-unit]);
- }
- /*
- * Reprogram the UDMA/PIO of our drive for the switch.
- * MWDMA will be dealt with by the dma switcher
- */
- if(itdev->udma[unit] != UDMA_OFF) {
- it821x_program_udma(drive, itdev->udma[unit]);
- it821x_program(drive, itdev->pio[unit]);
- }
-}
-
-/**
- * it821x_set_pio_mode - set host controller for PIO mode
- * @hwif: port
- * @drive: drive
- *
- * Tune the host to the desired PIO mode taking into the consideration
- * the maximum PIO mode supported by the other device on the cable.
- */
-
-static void it821x_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- ide_drive_t *pair = ide_get_pair_dev(drive);
- const u8 pio = drive->pio_mode - XFER_PIO_0;
- u8 unit = drive->dn & 1, set_pio = pio;
-
- /* Spec says 89 ref driver uses 88 */
- static u16 pio_timings[]= { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
- static u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
-
- /*
- * Compute the best PIO mode we can for a given device. We must
- * pick a speed that does not cause problems with the other device
- * on the cable.
- */
- if (pair) {
- u8 pair_pio = pair->pio_mode - XFER_PIO_0;
- /* trim PIO to the slowest of the master/slave */
- if (pair_pio < set_pio)
- set_pio = pair_pio;
- }
-
- /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
- itdev->want[unit][1] = pio_want[set_pio];
- itdev->want[unit][0] = 1; /* PIO is lowest priority */
- itdev->pio[unit] = pio_timings[set_pio];
- it821x_clock_strategy(drive);
- it821x_program(drive, itdev->pio[unit]);
-}
-
-/**
- * it821x_tune_mwdma - tune a channel for MWDMA
- * @drive: drive to set up
- * @mode_wanted: the target operating mode
- *
- * Load the timing settings for this device mode into the
- * controller when doing MWDMA in pass through mode. The caller
- * must manage the whole lack of per device MWDMA/PIO timings and
- * the shared MWDMA/PIO timing register.
- */
-
-static void it821x_tune_mwdma(ide_drive_t *drive, u8 mode_wanted)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct it821x_dev *itdev = (void *)ide_get_hwifdata(hwif);
- u8 unit = drive->dn & 1, channel = hwif->channel, conf;
-
- static u16 dma[] = { 0x8866, 0x3222, 0x3121 };
- static u8 mwdma_want[] = { ATA_ANY, ATA_66, ATA_ANY };
-
- itdev->want[unit][1] = mwdma_want[mode_wanted];
- itdev->want[unit][0] = 2; /* MWDMA is low priority */
- itdev->mwdma[unit] = dma[mode_wanted];
- itdev->udma[unit] = UDMA_OFF;
-
- /* UDMA bits off - Revision 0x10 do them in pairs */
- pci_read_config_byte(dev, 0x50, &conf);
- if (itdev->timing10)
- conf |= channel ? 0x60: 0x18;
- else
- conf |= 1 << (3 + 2 * channel + unit);
- pci_write_config_byte(dev, 0x50, conf);
-
- it821x_clock_strategy(drive);
- /* FIXME: do we need to program this ? */
- /* it821x_program(drive, itdev->mwdma[unit]); */
-}
-
-/**
- * it821x_tune_udma - tune a channel for UDMA
- * @drive: drive to set up
- * @mode_wanted: the target operating mode
- *
- * Load the timing settings for this device mode into the
- * controller when doing UDMA modes in pass through.
- */
-
-static void it821x_tune_udma(ide_drive_t *drive, u8 mode_wanted)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- u8 unit = drive->dn & 1, channel = hwif->channel, conf;
-
- static u16 udma[] = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 };
- static u8 udma_want[] = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 };
-
- itdev->want[unit][1] = udma_want[mode_wanted];
- itdev->want[unit][0] = 3; /* UDMA is high priority */
- itdev->mwdma[unit] = MWDMA_OFF;
- itdev->udma[unit] = udma[mode_wanted];
- if(mode_wanted >= 5)
- itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */
-
- /* UDMA on. Again revision 0x10 must do the pair */
- pci_read_config_byte(dev, 0x50, &conf);
- if (itdev->timing10)
- conf &= channel ? 0x9F: 0xE7;
- else
- conf &= ~ (1 << (3 + 2 * channel + unit));
- pci_write_config_byte(dev, 0x50, conf);
-
- it821x_clock_strategy(drive);
- it821x_program_udma(drive, itdev->udma[unit]);
-
-}
-
-/**
- * it821x_dma_read - DMA hook
- * @drive: drive for DMA
- *
- * The IT821x has a single timing register for MWDMA and for PIO
- * operations. As we flip back and forth we have to reload the
- * clock. In addition the rev 0x10 device only works if the same
- * timing value is loaded into the master and slave UDMA clock
- * so we must also reload that.
- *
- * FIXME: we could figure out in advance if we need to do reloads
- */
-
-static void it821x_dma_start(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- u8 unit = drive->dn & 1;
-
- if(itdev->mwdma[unit] != MWDMA_OFF)
- it821x_program(drive, itdev->mwdma[unit]);
- else if(itdev->udma[unit] != UDMA_OFF && itdev->timing10)
- it821x_program_udma(drive, itdev->udma[unit]);
- ide_dma_start(drive);
-}
-
-/**
- * it821x_dma_write - DMA hook
- * @drive: drive for DMA stop
- *
- * The IT821x has a single timing register for MWDMA and for PIO
- * operations. As we flip back and forth we have to reload the
- * clock.
- */
-
-static int it821x_dma_end(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- int ret = ide_dma_end(drive);
- u8 unit = drive->dn & 1;
-
- if(itdev->mwdma[unit] != MWDMA_OFF)
- it821x_program(drive, itdev->pio[unit]);
- return ret;
-}
-
-/**
- * it821x_set_dma_mode - set host controller for DMA mode
- * @hwif: port
- * @drive: drive
- *
- * Tune the ITE chipset for the desired DMA mode.
- */
-
-static void it821x_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- const u8 speed = drive->dma_mode;
-
- /*
- * MWDMA tuning is really hard because our MWDMA and PIO
- * timings are kept in the same place. We can switch in the
- * host dma on/off callbacks.
- */
- if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_6)
- it821x_tune_udma(drive, speed - XFER_UDMA_0);
- else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
- it821x_tune_mwdma(drive, speed - XFER_MW_DMA_0);
-}
-
-/**
- * it821x_cable_detect - cable detection
- * @hwif: interface to check
- *
- * Check for the presence of an ATA66 capable cable on the
- * interface. Problematic as it seems some cards don't have
- * the needed logic onboard.
- */
-
-static u8 it821x_cable_detect(ide_hwif_t *hwif)
-{
- /* The reference driver also only does disk side */
- return ATA_CBL_PATA80;
-}
-
-/**
- * it821x_quirkproc - post init callback
- * @drive: drive
- *
- * This callback is run after the drive has been probed but
- * before anything gets attached. It allows drivers to do any
- * final tuning that is needed, or fixups to work around bugs.
- */
-
-static void it821x_quirkproc(ide_drive_t *drive)
-{
- struct it821x_dev *itdev = ide_get_hwifdata(drive->hwif);
- u16 *id = drive->id;
-
- if (!itdev->smart) {
- /*
- * If we are in pass through mode then not much
- * needs to be done, but we do bother to clear the
- * IRQ mask as we may well be in PIO (eg rev 0x10)
- * for now and we know unmasking is safe on this chipset.
- */
- drive->dev_flags |= IDE_DFLAG_UNMASK;
- } else {
- /*
- * Perform fixups on smart mode. We need to "lose" some
- * capabilities the firmware lacks but does not filter, and
- * also patch up some capability bits that it forgets to set
- * in RAID mode.
- */
-
- /* Check for RAID v native */
- if (strstr((char *)&id[ATA_ID_PROD],
- "Integrated Technology Express")) {
- /* In raid mode the ident block is slightly buggy
- We need to set the bits so that the IDE layer knows
- LBA28. LBA48 and DMA ar valid */
- id[ATA_ID_CAPABILITY] |= (3 << 8); /* LBA28, DMA */
- id[ATA_ID_COMMAND_SET_2] |= 0x0400; /* LBA48 valid */
- id[ATA_ID_CFS_ENABLE_2] |= 0x0400; /* LBA48 on */
- /* Reporting logic */
- printk(KERN_INFO "%s: IT8212 %sRAID %d volume",
- drive->name, id[147] ? "Bootable " : "",
- id[ATA_ID_CSFO]);
- if (id[ATA_ID_CSFO] != 1)
- printk(KERN_CONT "(%dK stripe)", id[146]);
- printk(KERN_CONT ".\n");
- } else {
- /* Non RAID volume. Fixups to stop the core code
- doing unsupported things */
- id[ATA_ID_FIELD_VALID] &= 3;
- id[ATA_ID_QUEUE_DEPTH] = 0;
- id[ATA_ID_COMMAND_SET_1] = 0;
- id[ATA_ID_COMMAND_SET_2] &= 0xC400;
- id[ATA_ID_CFSSE] &= 0xC000;
- id[ATA_ID_CFS_ENABLE_1] = 0;
- id[ATA_ID_CFS_ENABLE_2] &= 0xC400;
- id[ATA_ID_CSF_DEFAULT] &= 0xC000;
- id[127] = 0;
- id[ATA_ID_DLF] = 0;
- id[ATA_ID_CSFO] = 0;
- id[ATA_ID_CFA_POWER] = 0;
- printk(KERN_INFO "%s: Performing identify fixups.\n",
- drive->name);
- }
-
- /*
- * Set MWDMA0 mode as enabled/support - just to tell
- * IDE core that DMA is supported (it821x hardware
- * takes care of DMA mode programming).
- */
- if (ata_id_has_dma(id)) {
- id[ATA_ID_MWDMA_MODES] |= 0x0101;
- drive->current_speed = XFER_MW_DMA_0;
- }
- }
-
-}
-
-static const struct ide_dma_ops it821x_pass_through_dma_ops = {
- .dma_host_set = ide_dma_host_set,
- .dma_setup = ide_dma_setup,
- .dma_start = it821x_dma_start,
- .dma_end = it821x_dma_end,
- .dma_test_irq = ide_dma_test_irq,
- .dma_lost_irq = ide_dma_lost_irq,
- .dma_timer_expiry = ide_dma_sff_timer_expiry,
- .dma_sff_read_status = ide_dma_sff_read_status,
-};
-
-/**
- * init_hwif_it821x - set up hwif structs
- * @hwif: interface to set up
- *
- * We do the basic set up of the interface structure. The IT8212
- * requires several custom handlers so we override the default
- * ide DMA handlers appropriately
- */
-
-static void init_hwif_it821x(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct ide_host *host = pci_get_drvdata(dev);
- struct it821x_dev *itdevs = host->host_priv;
- struct it821x_dev *idev = itdevs + hwif->channel;
- u8 conf;
-
- ide_set_hwifdata(hwif, idev);
-
- pci_read_config_byte(dev, 0x50, &conf);
- if (conf & 1) {
- idev->smart = 1;
- hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
- /* Long I/O's although allowed in LBA48 space cause the
- onboard firmware to enter the twighlight zone */
- hwif->rqsize = 256;
- }
-
- /* Pull the current clocks from 0x50 also */
- if (conf & (1 << (1 + hwif->channel)))
- idev->clock_mode = ATA_50;
- else
- idev->clock_mode = ATA_66;
-
- idev->want[0][1] = ATA_ANY;
- idev->want[1][1] = ATA_ANY;
-
- /*
- * Not in the docs but according to the reference driver
- * this is necessary.
- */
-
- if (dev->revision == 0x10) {
- idev->timing10 = 1;
- hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
- if (idev->smart == 0)
- printk(KERN_WARNING DRV_NAME " %s: revision 0x10, "
- "workarounds activated\n", pci_name(dev));
- }
-
- if (idev->smart == 0) {
- /* MWDMA/PIO clock switching for pass through mode */
- hwif->dma_ops = &it821x_pass_through_dma_ops;
- } else
- hwif->host_flags |= IDE_HFLAG_NO_SET_MODE;
-
- if (hwif->dma_base == 0)
- return;
-
- hwif->ultra_mask = ATA_UDMA6;
- hwif->mwdma_mask = ATA_MWDMA2;
-
- /* Vortex86SX quirk: prevent Ultra-DMA mode to fix BadCRC issue */
- if (idev->quirks & QUIRK_VORTEX86) {
- if (dev->revision == 0x11)
- hwif->ultra_mask = 0;
- }
-}
-
-static void it8212_disable_raid(struct pci_dev *dev)
-{
- /* Reset local CPU, and set BIOS not ready */
- pci_write_config_byte(dev, 0x5E, 0x01);
-
- /* Set to bypass mode, and reset PCI bus */
- pci_write_config_byte(dev, 0x50, 0x00);
- pci_write_config_word(dev, PCI_COMMAND,
- PCI_COMMAND_PARITY | PCI_COMMAND_IO |
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
- pci_write_config_word(dev, 0x40, 0xA0F3);
-
- pci_write_config_dword(dev,0x4C, 0x02040204);
- pci_write_config_byte(dev, 0x42, 0x36);
- pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
-}
-
-static int init_chipset_it821x(struct pci_dev *dev)
-{
- u8 conf;
- static char *mode[2] = { "pass through", "smart" };
-
- /* Force the card into bypass mode if so requested */
- if (it8212_noraid) {
- printk(KERN_INFO DRV_NAME " %s: forcing bypass mode\n",
- pci_name(dev));
- it8212_disable_raid(dev);
- }
- pci_read_config_byte(dev, 0x50, &conf);
- printk(KERN_INFO DRV_NAME " %s: controller in %s mode\n",
- pci_name(dev), mode[conf & 1]);
- return 0;
-}
-
-static const struct ide_port_ops it821x_port_ops = {
- /* it821x_set_{pio,dma}_mode() are only used in pass-through mode */
- .set_pio_mode = it821x_set_pio_mode,
- .set_dma_mode = it821x_set_dma_mode,
- .quirkproc = it821x_quirkproc,
- .cable_detect = it821x_cable_detect,
-};
-
-static const struct ide_port_info it821x_chipset = {
- .name = DRV_NAME,
- .init_chipset = init_chipset_it821x,
- .init_hwif = init_hwif_it821x,
- .port_ops = &it821x_port_ops,
- .pio_mask = ATA_PIO4,
-};
-
-/**
- * it821x_init_one - pci layer discovery entry
- * @dev: PCI device
- * @id: ident table entry
- *
- * Called by the PCI code when it finds an ITE821x controller.
- * We then use the IDE PCI generic helper to do most of the work.
- */
-
-static int it821x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
- struct it821x_dev *itdevs;
- int rc;
-
- itdevs = kcalloc(2, sizeof(*itdevs), GFP_KERNEL);
- if (itdevs == NULL) {
- printk(KERN_ERR DRV_NAME " %s: out of memory\n", pci_name(dev));
- return -ENOMEM;
- }
-
- itdevs->quirks = id->driver_data;
-
- rc = ide_pci_init_one(dev, &it821x_chipset, itdevs);
- if (rc)
- kfree(itdevs);
-
- return rc;
-}
-
-static void it821x_remove(struct pci_dev *dev)
-{
- struct ide_host *host = pci_get_drvdata(dev);
- struct it821x_dev *itdevs = host->host_priv;
-
- ide_pci_remove(dev);
- kfree(itdevs);
-}
-
-static const struct pci_device_id it821x_pci_tbl[] = {
- { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), 0 },
- { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), 0 },
- { PCI_VDEVICE(RDC, PCI_DEVICE_ID_RDC_D1010), QUIRK_VORTEX86 },
- { 0, },
-};
-
-MODULE_DEVICE_TABLE(pci, it821x_pci_tbl);
-
-static struct pci_driver it821x_pci_driver = {
- .name = "ITE821x IDE",
- .id_table = it821x_pci_tbl,
- .probe = it821x_init_one,
- .remove = it821x_remove,
- .suspend = ide_pci_suspend,
- .resume = ide_pci_resume,
-};
-
-static int __init it821x_ide_init(void)
-{
- return ide_pci_register_driver(&it821x_pci_driver);
-}
-
-static void __exit it821x_ide_exit(void)
-{
- pci_unregister_driver(&it821x_pci_driver);
-}
-
-module_init(it821x_ide_init);
-module_exit(it821x_ide_exit);
-
-module_param_named(noraid, it8212_noraid, int, S_IRUGO);
-MODULE_PARM_DESC(noraid, "Force card into bypass mode");
-
-MODULE_AUTHOR("Alan Cox");
-MODULE_DESCRIPTION("PCI driver module for the ITE 821x");
-MODULE_LICENSE("GPL");